Related
Hey guys, I was just about to purchase this case but then started wondering if it would adversely affect my signal strength so I thought I would jump on here and see if any of you have used an aluminum case and what the results were...
Thanks for any info, you guys rock!
It has a very good possibility of affecting the signal since the antenna will have a clunk of metal around it. But I dont have any first hand knowledge. Why not just get a plastic case. They effect it less.
I really want a case that has a door with a window on it..do you know of any plastic one?
Anyone else have any experience with aluminum cases?
Perhaps I am a pioneer in the area of aluminum cases and the HTC Mogul...or perhaps no one is paying attention to this thread because it's posted in the wrong area. I don't suppose an admin could move this over to the accessories sub forum could they.
Aside from this, where is the antenna located in the mogul? I'm thinking that if I do end up with signal issues I will cut slits the length of the antenna in the case.
Any info on this would be greatly appreciated!
conradcliff said:
Perhaps I am a pioneer in the area of aluminum cases and the HTC Mogul...or perhaps no one is paying attention to this thread because it's posted in the wrong area. I don't suppose an admin could move this over to the accessories sub forum could they.
Aside from this, where is the antenna located in the mogul? I'm thinking that if I do end up with signal issues I will cut slits the length of the antenna in the case.
Any info on this would be greatly appreciated!
Click to expand...
Click to collapse
Sounds pretty cool, can you link us to the particular case mentioned? Other than that I have no experience with metal (aluminum is considered a metal for the banterers) cases either. Personally I would stick to plastic, but sounds neat.
There's a link to it in the first post, but here it is again.
I've been walking around with an ipaq 2215 for the last 5 years with an aluminum case and that thing has saved my life on many occasions.
The plastic would be ok too I think, but only if I could find one that had a door that closed over the screen..
Who do you think I should talk to to get this moved over into accessories? I didn't even realize there was an accessories category when I posted this..
conradcliff said:
There's a link to it in the first post, but here it is again.
I've been walking around with an ipaq 2215 for the last 5 years with an aluminum case and that thing has saved my life on many occasions.
The plastic would be ok too I think, but only if I could find one that had a door that closed over the screen..
Who do you think I should talk to to get this moved over into accessories? I didn't even realize there was an accessories category when I posted this..
Click to expand...
Click to collapse
That case is awesome. I really like it. Interested to see if it ruins the signal quality, or possibly enhance it lol I dont know.. It looks properly designed, I am sure the manufacturer took the antenna location into consideration. I would go for it. Let me know how it works out, hopefully by then one is still available. I can grab one myself.
I will have this moved for you.
Thanks for getting this moved for me Ryan..yeah, I think I'm going to purchase the case within the next few days unless someone pipes in with a negative review.
In the meantime, does anyone know where the antenna is located in the 6800?
Thanks for any help!
So, I came in here to bump the thread up one more time before I bought the case, but it was still at the top...doesn't seem like people are too concerned about Titan accessories any longer
I guess 150 views is enough though, I think I'm just going to bite the bullet and buy.
Will update once I've tested in the low signal areas that I frequent.
I had the exact same case for my xv6700 and never had any signal issues. The case worked well and kept my 6700 looking brand new!
I really liked the lexan screen cover.
I tried the seidio rubberized case for my titan. it worked awesome for about 10 months until the little tiny tabs that held it on broke off. Only a 90 day warrenty so SOL. Now I use a cudora pouch.
So let me know how the aircraft aluminum one fits!!
That's great to hear! I'm going to order it tonight and maybe upload some pics when I get it..
hi conradcliff
dont forget test review the case (how about the look, size etc) and upload the pict, i want to buy also, but it seems need 2 week to deliver it to my country
Oh I most certainly will..I'll also post the coupon code they gave me for 10% off, hopefully it will work for anyone.
Initial Review: Monaco Aluminum Case for Mogul/6800
Short answer: A well designed, sturdy case well worth the ~ $20 price. I'll add some photos soon. Sorry if I stepped on anyone's toes who intended to write one of these up, but hey, two opinions are better than one!
I've had three of these cases for three separate Sprint 6800's. Two black, one silver. For those familiar with Monaco Aluminum Cases (they made/make these for other phones, such as the 6700), this embodiment is just as good.
Pros:
Very solid design - this case can easily outlast the life of your phone. Aside from slight exterior discoloration, dings, and scratches, this case should easily withstand all normal, day-to-day use.
Inner liner - this case includes an inner liner made of neoprene that protects the phone from minor scratch/abrasion marks; that provides a very snug fit for the phone; and provides *minimal* fall protection. Two-story drops and projectile usage by angry girlfriends are not protected.
Access - the case provides access to all buttons, dials, interfaces (except for touch screen & slide-out KB). Luckily, almost all functionality of this phone can be effectuated without the touch screen (not the TP, grrrr), so you will not have to open the case too often, which is very nice. When you do open the case, the keyboard slides over the open top of the case nicely.
Vents (Air/Signal) - there are vents on the top, back, and right side of the case for air and/or signal paths. I've experienced no signal difference, or even heat difference, with this case. I'm sure it does insulate the phone to some degree, but it's minimal.
Belt Clip - the case comes with a belt clip and swivel that are relatively secure and convenient. I've had one belt clip split (the plunger portion), but it is still very usable. You don't have to use them, but I do. The round swivel that screws into the back of the case provides a nicer grip of the phone, IMHO. If you don't like either, you don't have to use them.
Cons:
Weight - it does add weight to your phone. It's not extreme, but holding the phone for extended periods of time may prove annoying by some with this extra weight. I don't mind it at all, and I have a headset and use speakerphone anyhow.
User Adjustment Required - Out of the box, this case is NOT ready to use! You absolutely must gauge how well the metal clip engages the main body of the case. Every case I've received required me to slightly bend the clip inwards to provide a stronger hold. If the hold is too weak, brushing against the side of the case (by your arm when walking with the case attached to your waist side, or by anything you may brush against) can result in your phone falling out to the ground. So, adjust the clip right away, and ALWAYS, periodically check it, as repeated opening may loosen the hold over time. Also, when wearing this case attached to the side of your hip, attach it to your left side so the metal clip and catch of the case are facing behind you. This way, brushing against something while you're walking will not accidentally open your case allowing your phone to drop out.
Plastic Cover - this cover can scratch. I tried placing a screen protectors over it, but they would never stay. The oil from your face/hands/etc, along with the lack of a frame protecting the edges of a protector from friction are mostly to blame. However I've learned that with a little care, the plastic screen can survive everyday use quite nicely.
So, I highly recommend this case!!
10% off coupon code -> EIWQC1257830
"Simply insert the coupon code during our checkout process and instantly save 10% off the merchandise.
You can use the coupon up to 5 times. This code will expire after 60 days [from 10/7/09]."
There's more to know though so don't buy until you get my review..hopefully tomorrow.
Can anyone recommend a windscreen mount that would meet my following requirements?
1. Must hold the HD2 securely (goes without saying) - but doesn't have to be specifically designed for the HD2
2. Under or around £10 (can't afford those £40-£60 'official' things!)
3. Must not block camera lens as I wish to record some of my journeys
4. Can swivel portrait/landscape without removing
I have found a fair view that 'might' meet these requirements but I'd like to know for sure.
- http://cgi.ebay.co.uk/AIO-PREMIUM-C...ries_MobilePhoneBatteries?hash=item2304e852d0 <--- this looks decent but I can't work out whether it blocks the lens or not??
- http://www.dealextreme.com/details.dx/sku.1154
(some more but I've lost the urls - loads on DX to choose from)
Any help's much appreciated!
Hi, I bought this one on eBay:
WINDSCREEN SUCTION CAR HOLDER & CHARGER FOR HTC HD2 LEO, the company is "e-Cell"
It arrived yesterday and it works the way you want it to - there is a hole for the camera lens, but not for the LEDs, and it swivels all the way round.
It costs £7.85, with free P & P, and includes a cigarette lighter power supply (which I haven't used yet).
I hope this helps.
EDIT: I checked and the item is no longer listed - perhaps they're out of stock.
Thanks John, I managed to find the one you're referring to via Google but as you say it's sold out: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=200433261802
It looks very similar to the ones being sold by DX for other devices (currently none on DX for HD2), e.g.
http://www.dealextreme.com/details.dx/sku.18225
http://www.dealextreme.com/details.dx/sku.22814
It looks decent - how easy is it to put your HD2 into and remove it from the holder?
I've also found this super cheap universal one on DX: http://www.dealextreme.com/details.dx/sku.23565
...which allows full swiveling and most likely the top of the HD2 (camera, flash) would stick out from the holder making it accessible for filming. I may order this one as I can always give it to a friend if it doesn't work out, though I'm def still interested in more stuff like your link.
Cheers
The Capdase Car Mount will work.
Try E-CELL on E-bay. I bought mine there, it is a veryy good holder for the HD2 and cost app. 8 pounds.
Search ebay for this "Holder Mount USB Car Charger For HTC Touch HD2 Leo 100". Has opening for camera and holds phone in landscape which is good for copilot.
Hi,
This is for the e-Cell model:
If you imagine the phone in the landscape position, with the five buttons to the right, the phone slots into two grips left and right, at the bottom. These are fixed and don't move, but at the top, in the centre of the phone holder is another clip that flexes to allow the insertion and removal of the phone. This piece of plastic then clips onto a standard flexible arm windscreen mount, which in turn fixes to the windscreen with a suction cup. There is a ball joint on the back of the phone clip, which, when you've found your best position, can be tightened to lock the mount so that it will not move.
I've only used mine a couple of times and it's relatively easy to put in and remove the phone, perhaps a bit stiff at first, and I've found it easier to fit the phone into the holder first and then attach the complete assembly to the windscreen. It seems to work OK, so it may be worth waiting for e-Cell to get new stock, particularly as you also get a cigarette lighter charger, and it's only £7.85 with free postage.
This looks similar to the e-Cell model:
http://www.mobilefun.co.uk/car-pack-for-the-htc-hd2-p23420.htm but they're sold out too! The joint on this looks more sophisticated, but it's more than twice as expensive. There seems to be a hole for the lens, but the picture isn't very clear.
http://cgi.ebay.it/ws/eBayISAPI.dll?ViewItem&item=280435698894&ssPageName=STRK:MEWNX:IT
mine, cheapest and camera effective, even if I'd prefer a joint-like arm instead of the one it's got
Hi Ephestione,
It's a pity we can't combine the best features of all the mounts. For instance, mine doesn't have the cushioned grips, so I'll have to be careful not to scratch the phone with the rigid clips.
http://cgi.ebay.co.uk/Car-Charger-Mount-Kit-Holder-for-HTC-Touch-HD-2-T8585_W0QQitemZ390175231504QQcmdZViewItemQQptZUK_MobilePhones_MobilePhoneAccessories_MobilePhoneBatteries?hash=item5ad8418e10
this one is available, exacly the same as ecell one, but will come "out of the box", and comes with a charger too. this seller also got the 1600mah andida battery.
for recording purpose, another good point is its having a strong and quite short metal neck that won't take cars vibrations as a long neck/flexible one would. definitely would recomend it.
Hi,
Yes, this is the same as the e-Cell item, and it works well. I paid a bit more because I was impatient and e-Cell seem to be UK based, so delivery was quicker. Some comments I found when I googled the holder questioned the location of the company, but I had no problems. I'll check out the battery, thanks.
I bought this and it will suit ur needs.
What is the ideal case for your Nook Color?
Is it one that is available or not?
What are some of the features you would like it to have?
Do you want a fold case that covers the screen?
Is the micro usb port in a convenient location?
Looking for some ideas. Working on a shell now for a mold. Not sure if anything will come of it but want to see what you all are looking for in a case. Feel free to post your thoughts. Thanks.
I would like to see a one sided hard cover that can protect the screen when not in use and snap onto the rear when in use. Probably use the typical four corner frame system you see in many cases so nothing is obstructed.
Also, have a stand "system" so that when it is snapped to the rear you can prop up the NC. Maybe something like what you see on back side of keyboards. And like some keyboards I've seen, have different levels of lift. One lift level that slightly raises the NC off the surface, for typing and such. Another lift level that is like the leg stand you see on the EVO 4G or Archos 70, for video/picture viewing and the like.
Heh. First post around here. Been meaning to chime in on a thread and this is the perfect one to start. Only because I've been looking for something I described but there is nothing out there yet.
I'm looking for an inexpensive silicone gel skin, something I'd keep on pretty much all the time. I'm also keeping my eyes open for sturdy travel case.
There seem to be choices out there for both, I'm just waiting a bit for more of them to hit ebay.
I missed your last question about the micro usb port. IMO its not in a good location because its awkward when trying to read while charging, particularly when reclining or lying down. I'm concerned about putting pressure on the usb cable, especially considering its not just a standard cheap cable. Not sure how a case will help this, though.
drp1 said:
I missed your last question about the micro usb port. IMO its not in a good location because its awkward when trying to read while charging, particularly when reclining or lying down. I'm concerned about putting pressure on the usb cable, especially considering its not just a standard cheap cable. Not sure how a case will help this, though.
Click to expand...
Click to collapse
ill be trying out a few designs once the mold sets. i can add a ribbon cable in the case to move the USB port to the sides which I might try. trying to keep it thin but actually worth putting on.
techboydino said:
ill be trying out a few designs once the mold sets. i can add a ribbon cable in the case to move the USB port to the sides which I might try. trying to keep it thin but actually worth putting on.
Click to expand...
Click to collapse
Are you designing desktop/multimedia cases as well? I would love additional speakers on the NC and also a magnetic swivel X mount stand for desktop use.
My ideal case is not available yet. It is an envelope-like case that will allow me to pull the Nook out and use it naked. Something in nice black leather.
Something similiar to the covers of the TI calculators, with a little more thought about aesthetics obviously.
A 90deg connector or adapter would be nice. Then run the cable through the corner loop thingie.
Cheers,
kev
bugeyed1 said:
A 90deg connector or adapter would be nice. Then run the cable through the corner loop thingie.
Cheers,
kev
Click to expand...
Click to collapse
Good Idea, I may try that out.
Im not any sort of professional or anything, but I do have access to some pretty sweet resin's and molding equipment. Carbon fiber is the idea, but the glass mold and how I want to do the front part comes first. Ill keep the thread updated.
ideal nook case
looking for something very close to this case
http://www.amazon.com/gp/product/B0040VNRTG/ref=oss_product
just substituting the swivel belt clip for a kickstand
i like the idea of moving the usb jack to another spot but i think that would add alot of cost and effort to the case build
Rube Goldberg lives; or, is this even possible?
You asked for the ideal, here is mine. Not at all sure it is doable....
1. In the interest of keeping the total package as slim as possible, no back, unless it is necessary to support other features.
2. [Front] cover has a slot for a pad of paper and/or corner slots for index cards.
3. [Front] cover is hinged on the right (I'm right handed and I want to be able to write easily).
4. [Front] cover has a foldover flap to keep the paper or cards from contacting the screen when the cover is closed.
5. The cover can fold 180 degrees so that the cover lies flat against the back of the tablet.
6. The cover can support the Nook as an easel in landscape mode.
7. The cover can support the Nook as an easel in portrait mode - this might involve some sort of short extension legs or other support to raise the lower edge of the Nook an inch or so (and this might help with the need to plug in the USB connector at the bottom).
8. Bonus points for the ability to fold out a handle attached at the lower left corner when in portrait mode, sort of like a hand mirror.
9. And of course it should be strong, light, durable, elegant, and less than $40 US.
I'm ready to order as soon as I see the pictures of the finished product.
Thanks for the ideas everyone. Haven't worked on it in a few due to being out at CES. Unfortunately there were NO cases out there. Working with Speck to find something but tried everything else and could not even find a nice slip cover. Otterbox said they are testing designs so no real info there either.
My ideal case is something like
http://shop.brando.com/samsung-galaxy-tab-case-with-bluetooth-keyboard_p05269c0299d057.html
this.
Bluetooth keyboard case, waiting for bluetooth to work for NOOK!! and I could use it as a netbook and a tablet. IDEAL.
This is my cheap (free) case for my nook color. It’s the zippered case for my trucks instruction manual. The patch covers the ford symbol; if I need to hide it in plain sight I can pull the patch off and leave it in the back seat. It fits perfectly and there is a plastic divider on the inside I can put business cards and a small pad of paper (as others have asked). All I keep in it is a set of skullcandy headphones in an microfiber Oakley sunglass bag for cleaning the screen.
michael
-"I learned a very valuable lesson on my travels, Tucker. No matter how bad things might seem..."
-"They could be worse?"
-"Nope, no matter how bad they seem, they can't be any better, and they can't be any worse, because that's the way things fraking are, and you better get used to it Nancy. Quit yer *****ing."
Perfect case for the Nook Color
Before I bought my Nook, I had a Pandigital Novel that I bought on eBay.
In the same eBay search results page the Novel appeared on was a great case called BookArmor. Although it was $35, I bought it. And I haven't regretted it either.
The BookArmor case comes with a set of velcro-like pads that stick on the back of the tablet and allow it to be fixed to the case. The case itself is laminated steel and plastic covered with textured fabric. It zippers shut and the zipper sides are soft and stay out of the way when the case is opened. You have total access to all side buttons and ports. The inside surface that comes in contact with the screen is covered with a soft foam pad.
When I decided to get the Nook, I found out that the case I had for the Novel is the exact same case for the Nook Color. I really like this case and haven't even considered another one.
For more info go to extremeinkjet.com and click on BookArmor cases in the blue left-hand column. Pick any Delta 6 case ... there is a Nook Color one. Checkout their video at the bottom of the page.
It looks like this case is really popular too ... there aren't any left on eBay and the extremeinkjet site shows all out of stock for the Delta 6 case. Amazon shows one Delta 6 left for the Pandigital (same case) but it doesn't even show up for Nook Color.
I don't know if I'd call it perfect. But, I bought the B&N case with the vertical flap and ribbon with magnet on the end to hold it closed/open. It works well for me.
If they were available in store when I bought my nook, I would have also considered the silicone one. Although, if I went that route, I'd probably prefer the otter box version with the hard resin exterior an rubber liner. I would also have considered the black leather pouch one where you completely remove the nook to use it.
Alas, none of these were available to me when I made my purchase so I'm using what I have.
With either the otter box or the silicone I would gain a thinner form factor. But, I would never be able to completely cover the screen. With the pouch one, I would gain the thin form factor when using and would not add much when transporting. But, it's basically just a branded leather sleeve.
In the end, what drew me to the case that I bought was the vertical flap and ribboned magnet. 1 - with the horizontal flapped ones, the magnet does not flip around to hold the flap to the back of the case so it's open like a book with the flap dangling out the right side. 2 - with the vertical one that I got, you flip the cover over the top, move the magnet to the back to hold the cover in place and you have all your nooky goodness to go to town with!
Just my 2 cents.
jlh8733 said:
Something similiar to the covers of the TI calculators, with a little more thought about aesthetics obviously.
Click to expand...
Click to collapse
Wow...love love love this idea.
This would be great..a hard protective slide case.
This would definitely be a $$$ maker.
I bought a "Industriell Cover in Storm" cover and it works perfectly, very simple, protects the screen, and it's small.
I'm stealing your "DON'T PANIC" sticker on the back idea. thanks for reminding me.
When I had the Eris I used some plexiglass and a heat gun to make a cradle but with the button placement and shape of the DInc, it was a bit harder to make so I designed a simple holder in SolidWorks to hold the phone vertically. It holds it by the bottom 1" of the phone and has a cut out for the charger. I attached it to my car using 3M exterior mounting tape(great stuff) and it has been working very well for me.
If you want one, just order it from here http://shpws.me/1wfv. However I think there is a minimum order from this place of $25 and takes about 3 weeks to get because they have to put it into their que to print and then it gets shipped from overseas.
I made another one today that is designed to hold the phone horizontally. It has cut-outs for the USB, volume and power buttons. I just designed it today and have not test fit it but it should work without a problem.
I made one thin http://shpws.me/1LD8 and another with thicker walls http://shpws.me/1wo0. The thin walled one works for my vertical holder but it is a bit flimsy so you might want to opt for the thicker one at a slight increase in production cost.
Added more
I have designed two more holders which I have just ordered today and when I get them I will let everyone know how they fit.
The design of these is such that they are to be made from Alumide (http://www.shapeways.com/materials/alumide) and can hold the phone wither you have the standard battery or the official HTC extended battery. These holders only hold the phone by the lower 3/4" vs the previous 1" in order to save in material and therefore cost.
An additional feature that I added to the horizontal holder is a sleeve that should hold, with some glue, the official HTC video output cable.
Vertical Holder $15.52 - http://shpws.me/1LC7
Horizontal Holder $21.03 - http://shpws.me/1LBU
Both together $33.09 (save $3.46) - http://shpws.me/1Ltv
See all the things I have designed here http://www.shapeways.com/shops/tbe
Note: Prices listed are if you get this made in Alumide, you can get this made in a bunch of other materials and can save some money if you get plastic, or if you have the money and want to show off you can get this in silver. These have a wall thickness of 1.5mm/.06in so make sure you choose a material that allows for that thickness.
Note 2: There is a minimum of $25 when purchasing from this site of if you only get one of them, you might want to look at something else. If someone has a special request. I made these for my own use but I am sharing them to the world so that others may benefit.
They came today
I received the two holders in the mail today and they are pretty much perfect. The material is much stiffer than the regular plastic and it has a sparkle to it. I did a test fit with both the standard and oem extended batteries and they both have a nice snug fit. However, if you use a case, then you are SOL. On the horizontal holder, the video cable also slides right in and is snug to where I don't think any adhesives will be needed.
I have posted some pictures on the shapeway website.
Also, if anyone likes it but would like a modification to it, let me know.
I know this post is quite useless. I just wanted to vent out my frustration.
I just got off the phone with a B&N rep after 20 minutes of talking--because the rep kept beating around the bush and kept placing me on hold--and was told that I needed to callback on Monday to get the tracking no. for my 2nd--yup, this happened twice before--USB cable replacement. Yup, it broke again like the first one I got included with the NC--SIMPLY BECAUSE OF IT'S POOR QUALITY.
In generic micro USB cables, you would notice that most of them are made of rubber material, especially the one covering the tiny metal tip that you insert on the device's USB port, which makes them quite durable. Even if you bend it intentionally multiple times, the metal tip will not be affected that much. Only downside is, it doesn't fast charge the NC. In my experience, it takes a day and a half (about 36 hours) to be able to charge the NC fully. And yup, my NC is now turned off for a week (and counting).
The NC's stock USB cable however is made out of a gloss plastic material, probably to give way to the LED? light indicator? Downside is, it gets cracked/chipped off easily whether it was done unintentionally or not, because of the plastic material not being 'hard' enough, and that's where most NC owners like me are getting pissed off.
You have to be very careful whenever you charge the NC--you need to make sure that it's on a flat surface, not on a surface where it can sink itself say for example, a foam bed, so that the cable will not 'sink' with it in and put pressure on the metal tip, finally chipping off the plastic coating.
Do you guys know of any alternative that can fast-charge the NC like it's stock USB cable? Does anyone have the ability to modify the NC's stock USB cable to coat it with rubber or something to make it more durable?
I'm sure there are others who are experiencing these things. Hope we can gather around and start a discussion about getting a permanent fix. Maybe rally at a local B&N store or something, I dunno.
Well, a cheap and quick bit would be to wrap it with electrical tape. If you have an electronics store or Radio shack carrying it, there is also something called shrink tubing. this is a rubberish tube that when carefully heated with a heat gun (not a blow dryer) or a lighter, will shrink down around wires, or plastic.
But, I am rather annoyed with this serious design flaw as well. Would be nice if B&N either recalled these cables with a properly designed one, or get a 3rd party available to handle that.
I was thinking of reinforcing the plug end of the cable by encasing it in a big wad of epoxy putty.
epoxy putty usually cures to something a bit too brittle for what this really needs. As the OP said, the plastic on the plugs are really way too brittle for what it's meant for. other than those things, the other option I can think of is some of that latex dip sold in some hardware stores, or sex shops. wrap the metal bit in tape, then give it a few dips, let it cure, then carefully cut the tape off. instant rubberized plug. could even carefully cut an indicator window for the charge light.
heat shrink tubing sounds best. will try that. you can get it from home depot or lowes. get the multiple size package. it is really best to use a heat gun. if you dont know what your doing and use a lighter you will burn right through the heat shrink.
It sounds like you might be looking for Sugru. It hardens to a rubbery flexible consistency. There's also a how to floating around the web on making your own using caulk and ...baking soda? I think?
For that matter, a flexible clear caulk might do the trick.
I was thinking that RTV silicone (downside is long cure time) or maybe hot melt glue would be worth a try. Either one would be translucent enough to see the LED color. The Sugru looks interesting, although opaque like heat shrink tubing.
You could probably use something like Scotch Coat (more or less liquid electrical tape..) or plasti-dip perhaps?
*I'm still waiting on my NC to arrive. So, I'm not sure exactly which portion of the connector you're talking about. If it's the entire outside portion that is typically metal... this is normally a chasis ground which equalizes the chasis potential between the NC and whatever it's plugged into..., and really shouldn't be coated with anything
I ordered this off Amazon with the intent of fixing several things in my house. I was going to use the clear for the tip of the charger.
http://www.amazon.com/gp/product/B0027JIEPU
I think the shame of it is that all they had to do was use a strain relief sleeve like one of there:
Using the shrink tubing-
1. make sure you get a size large enough to get around the connection end.
2. Measure out a length. you want at least from the bottom of the N light to about 1/2 inch past the nub where the cord goes into the connector.
3. Slip the tube into place
4. Using a heat gun or lighter, carefully shrink the tube into place (NOTE: with a lighter, keep the flame moving, don't let it linger too long or you'll melt something)
5. If the resulting reinforcement doesn't seem enough, feel free to add another layer or 2.
WHAT DOES THIS ACCOMPLISH?
Well, most of the failure pictures I have seen, as well as the failed cord of my own, it seems the plastic is too friable (meaning it cracks really easy) to handle the stresses put on it at that end. Most of the cracks and fractures take place below the N, towards the cable side of the connection.
By adding this, it not only adds a semi flexible reinforcement around where it likes to crack up, it also stiffens and immobilizes a stretch of the cable, relieving a little of the stress that can happen in that part.
While other things might do the trick, and even electrical tape could do, this tubing is about the best option I've seen so far.
Srilania said:
While other things might do the trick, and even electrical tape could do, this tubing is about the best option I've seen so far.
Click to expand...
Click to collapse
Heat shrink tubing isn't a bad idea. I don't know how readily available it is in consumer stores and stuff... but I know I've used the Heat shrink tubing with the glue inside on quite a few connectors (higher end coaxial/heliax connectors tend to come with it). It's a bit thicker and more durable than typical heat shrink tubing, and the glue holds it solidly in place.
I used scotch tape. ugly, but it works.
Heat Shrink tubing shouldn't be too hard to find, most any electrical / hardware store should carry it, even Wal-mart will have it from time to time in the automotive section.
A better option may be plastidip. It gives a thick rubnery coating.
Sent from my NookColor using Tapatalk
After having a Nook Color for less than 6 months, mine just broke this morning! I would do without the LED indicator for a durable rubber casing.
Imbroglio said:
I was thinking of reinforcing the plug end of the cable by encasing it in a big wad of epoxy putty.
Click to expand...
Click to collapse
Epoxy works very well actually, but you need to put it on the inside, not the outside. Split open the plastic cover. Clean it up so it fits back together cleanly. Mix up a batch of translucent 5 Minute epoxy and completely fill the cavity with epoxy. Fit it back around the cable and secure it with a clip or clamp of your choice. A small binder clip works perfectly. After about 5 or ten minutes you can remove the clip and use an exacto knife to clean up the excess. Clamp it up again and
let it cure for 12 hours or so. Works well for me.
Triple wall heat shrink is just what you need. A heat gun (not a lighter, it won't work well) is the way to go. A hair dryer most likely won't have the heat needed.
I use the stuff in my home business and have tons of it...if you need some let me know!
I bent the male end that plugs into the nook unit... I Pressed the male end against a counter in my kitchen so it was bent back into place, put a few spots of super glue (the kind you get at the dollar store) and waited overnight for it to dry. good as new, no more wiggle or bend in my usb end.