Database Develop

[ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working)

T959 (US T-Mobile version of the Galaxy S) Firmware that can be flashed through Odin to restore all partitions to the way your phone was shipped to you.
WARNING!!! THIS WILL WIPE ANY DATA ON YOUR DEVICE, IT WILL REPLACE YOUR BASEBAND, KERNEL, RECOVERY AND OS.
JFD ODIN Images from Samsung (PDA)
www.justanotherdev.slackdev.com/T959UVJFD.tar
MD5:632730f6b637f53e5b10e5cbc8b966a7
512 PIT File (PIT Extract first!)
www.justanotherdev.slackdev.com/s1_odin_20100512.rar
MD5:b5628c8e183fdd8f4c703321ca40e33a
ODIN
www.justanotherdev.slackdev.com/Odin3.rar
ALL 3 Files plues the root update.zip
http://tinyurl.com/2bc5b6r
thx to KopyKatKiller
INSTRUCTIONS!
1.Your Device must be in DOWNLOAD mode to use ODIN.
2.Get your phone into Download mode by holding vol down and power.
3.THEN connect your phone to the USB. (some folks have had luck doing it in reverse..connecting the USB then Power and vol down)
4.Open Odin and load each file with it's corresponding field..PIT,PDA,CSC etc. (In this case we just use the PDA and PIT)
5.Don't check anything else, the other two boxes should be checked by default (Auto Reboot and Reset Time)
6.Hit "start"! be patient!
NOTE: COM3 worked fine for me. COM should not matter as long as you are using the correct drivers.
Finally we get some U.S love from samsung firmwares.
For those looking the Nandroid method it is in the post below but only recovers ,system, data, cache and datadata. Not your kernel/recovery or BASEBAND/RADIO (Modem.bin)
Thx to all helping work on the Vibrant. Especially Youneek, Scepterr, MS_Guru, Wes Garner, rhcp0112345, and anyone I may have forgot.
Twitter

NANDROID Images
Extract first!
For BaseBand T959UVJFD
ROOTED
www.justanotherdev.slackdev.com/2010-07-24.18.53.50.zip
MD5:ad0e4709593eb13c8494e62ebd949f17
UNROOTED
http://www.mediafire.com/?kqaulorzx5f6dyq
MD5:baf6e1d532b5dbd76723c64440420302
Thx to youneek.
To Restore
1. Make sure you have clockwork recovery installed (To get Clockwork see this thread)
2. Extract files to /sdcard/clockworkmod/backup/
3. Boot into recovery and select NANDroid and restore
Make sure to check USB debugging to enable ADB access after a restore.
This has been confirmed as WORKING before I uploaded. Any issues please post in this thread. Check MD5 as always after a download.
This will allow those that got stuck on a pre-release or EU ROM to go back to the shipped release TMO ROM for the Vibrant (JFD)
All the thanks goes to Koush for getting fakeflash working on the Vibrant allowing this to happen.

Came from the pre-release?
Flash the software in the first post via ODIN. The Pre-Release is garbage get back to JFD!!

Awesome.....You've just helped alot of people.

And now it begins....Nice to see you back bro!!

For later use...

WilliamStern said:
For later use...
Click to expand...
Click to collapse
why do you need to reserve space? The OP does this so they can post additional info if they need to and its not buried in the thread.

WilliamStern said:
For later use...
Click to expand...
Click to collapse
haha ;]
wanna be one of the first to say 'NANDROIDING!!!'?
i would too haha

You are doing a huge favor to many people, THANKS!

I'll also be adding one from totally stock. No clockworkmod, etc. just bone stock. It'll take about 5 minutes.

Thank you, finnaly! You're the man.
Sent from my SGH-T959 using XDA App

rsfaze said:
why do you need to reserve space? The OP does this so they can post additional info if they need to and its not buried in the thread.
Click to expand...
Click to collapse
How would it get buried? All he has to do is re-edit his OP with updates. It'll stay up top.

WilliamStern said:
How would it get buried? All he has to do is re-edit his OP with updates. It'll stay up top.
Click to expand...
Click to collapse
I think this board only lets you edit your OP after so many days.. but I could have this board mixed up with some of the others I'm on.

rsfaze said:
I think this board only lets you edit your OP after so many days.. but I could have this board mixed up with some of the others I'm on.
Click to expand...
Click to collapse
You could be right... My bad.

Thanks I am currently trying to make an update.zip version for everyone too.
Sent from my SGH-T959 using XDA App

My FTP is giving me fits so I'm uploading it to Multi-Share.

Maybe we should consolidate all of the stock rooted roms to one thread and users can report any problems with any of them.

justanothercrowd said:
My FTP is giving me fits so I'm uploading it to Multi-Share.
Click to expand...
Click to collapse
I am happy that you are back in the game. yours hero ports were the best on G1 back in the day

nick_karstedt said:
Maybe we should consolidate all of the stock rooted roms to one thread and users can report any problems with any of them.
Click to expand...
Click to collapse
we don't really have any yet.. until this nandroid is posted.. the 'stock' roms that have been posted in other threads have all been a beta pre-release from MS_guru.. and in my experience.. its pretty buggy

Great. Lets see if it restores the people who were fooling with the pre-release and had to update to the EU version.
Let us know when its up. and, tested.

[ATT 4.5.91(DEVS ONLY)] How to install stock 4.5.91 [READ THE WARNING & #2 POST]

Do not use this method any longer. there is safe alternatives for people who used this method, or kenns rom to return to stock without using ever sbf.​​Fruit Cakes (Safe Stock Builds for CWM)​Kennethpenn Gingerbread 2.3.4 Rom is safe​Navalynt's Cherryblur is also safe​

TEMPORARY FIX​If the need to return to 1.8.6 is huge. Or a requirement, and only if its a requirement . I suggest you do the following.​flash this special 183 sbf​
after installing sbf enter fastboot and type fastboot -w​YOU CAN NOT USE ANY SBF THAT DOES NOT CONTAIN PUDDING
This special sbf is the same that can be found here! And is created by The2dCour.​Big Thanks go to The2dCour for creating sbf and finding a temp fix. And to Jiva, AllTheWay and jruweaver for testing.​NOTE: It is safe to flash kenns rom and navylants rom. It is also safe to fastboot flash boot and system img.​

The boys are back in business ..

You really don't need to flash 1.8.3 before you install 4.5.91.
I flashed 4.5.91 right over my original stock 1.8.3 and it worked without a hitch.

Is this The ota that will be released soon?
Sent from my MB860 using XDA App

Your Update is labled 4.1.83... is this correct or wrong file?
Also, I notice the "Verifying account status" is back when trying to enable hotspot..

grave101 said:
You really don't need to flash 1.8.3 before you install 4.5.91.
I flashed 4.5.91 right over my original stock 1.8.3 and it worked without a hitch.
Click to expand...
Click to collapse
I am pretty sure its for all the people on 2.3.4

grave101 said:
You really don't need to flash 1.8.3 before you install 4.5.91.
I flashed 4.5.91 right over my original stock 1.8.3 and it worked without a hitch.
Click to expand...
Click to collapse
almost everyone here is rooted with cwm. if you have cwm the install wont work, you need a fresh sbf off 1.8.3, not to mention that you could have caused a brick because of your cache not having update.

sublimejosh2000 said:
Your Update is labled 4.1.83... is this correct or wrong file?
Also, I notice the "Verifying account status" is back when trying to enable hotspot..
Click to expand...
Click to collapse
Yes the update says 4.1.83, but i assure you this is the 4.5.97 update

Javi97100 said:
Is this The ota that will be released soon?
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
As far as we know this is the final build, kenneth also confirms the leak he got running on his phone is 4.5.91. theres other things in this build that give it away as final. no bugging tools, and no extra motorola testing apps.

sublimejosh2000 said:
Your Update is labled 4.1.83... is this correct or wrong file?
Also, I notice the "Verifying account status" is back when trying to enable hotspot..
Click to expand...
Click to collapse
Like sam said, its the right file. From the metadata:
post-build=MOTO/olyatt/olympus:2.3.4/4.5.91/110625:user/release-keys

samcripp said:
almost everyone here is rooted with cwm. if you have cwm the install wont work, you need a fresh sbf off 1.8.3, not to mention that you could have caused a brick because of your cache not having update.
Click to expand...
Click to collapse
I'm not sure what your talking about. I'm rooted with CWM as well. I cleared my cache through CWM and then installed the Gingerbread zip. There is no reason I should have caused a brick to my phone.
CWM is needed for the install.

grave101 said:
I'm not sure what your talking about. I'm rooted with CWM as well. I cleared my cache through CWM and then installed the Gingerbread zip. There is no reason I should have caused a brick to my phone.
CWM is needed for the install.
Click to expand...
Click to collapse
dude get off my thread, you install kenneths zip, that is desing to be installed that way, this is pure pure pure ota. this works comepletly stock, it wont work using CWM

grave101 said:
I'm not sure what your talking about. I'm rooted with CWM as well. I cleared my cache through CWM and then installed the Gingerbread zip. There is no reason I should have caused a brick to my phone.
CWM is needed for the install.
Click to expand...
Click to collapse
Apparently this doesn't use cwm....
Sent from my MB860 using Tapatalk

grave101 said:
I'm not sure what your talking about. I'm rooted with CWM as well. I cleared my cache through CWM and then installed the Gingerbread zip. There is no reason I should have caused a brick to my phone.
CWM is needed for the install.
Click to expand...
Click to collapse
AFAIK what Sam is trying to say is that this update.zip is not meant to be used with CWM as it is for stock recovery.
Sam correct me if I am wrong

4.5.91 or 4.5.97??
samcripp said:
Yes the update says 4.1.83, but i assure you this is the 4.5.97 update
Click to expand...
Click to collapse
Is this the 4.5.91 like Kenneth's or is this 4.5.97?

samcripp said:
dude get off my thread, you install kenneths zip, that is desing to be installed that way, this is pure pure pure ota. this works comepletly stock, it wont work using CWM
Click to expand...
Click to collapse
Lol...
Sent from my MB860 using Tapatalk

fastbikedroid said:
Is this the 4.5.91 like Kenneth's or is this 4.5.97?
Click to expand...
Click to collapse
That was a typo! He updated it to 4.5.91!

fastbikedroid said:
Is this the 4.5.91 like Kenneth's or is this 4.5.97?
Click to expand...
Click to collapse
that was a typo i corrected it, and this is not like kennesth release. thats mroe like a custom rom, is full of bugs, things may work or may not. not to knock it, as kenneth did an amazing job with his release. this is purely good old stable stock build. flash it, and rooted

samcripp said:
that was a typo i corrected it, and this is not like kennesth release. thats mroe like a custom rom, is full of bugs, things may work or may not. not to knock it, as kenneth did an amazing job with his release. this is purely good old stable stock build. flash it, and rooted
Click to expand...
Click to collapse
This is 2.3.4?

[system.img] GB 4.5.91 deodexed and rooted stock

This is kennethpenn's stock system.img from BriefMobile. I deodexed the system and framework and rooted it.
This is a stock deodexed app and framework. That is all. Use ./moto-fastboot flash system system.img to install it. I made this so i can keep data as i continue to build from stock up. If something gets borked i just flash the .img and start over will all data and most settings in tact. I am posting it to share for anyone who wants to have a stock deodexed image to base their personal rom off of. Begin with the deodexed system and hack away. if you break something flash the system again and keep all data.
Thanks to ...
kennethpenn for stock 4.5.91
Jug6ernaut for doo iit
s0dhi for the extra push
and xeudoxus for xUltimate
DOWNLOAD HERE

this one address the issue when batteries apk/odex been deodexed?

@PAulyhoffman
Would you be kind to do the same for the ORFR 2.3.4 please?

FabricioGS said:
@PAulyhoffman
Would you be kind to do the same for the ORFR 2.3.4 please?
Click to expand...
Click to collapse
Perhaps tomorrow

mramirezusa said:
this one address the issue when batteries apk/odex been deodexed?
Click to expand...
Click to collapse
No, this is basically stock. you will want to flash Jug6ernaut fix 2 on top of this if you want. or adb push the files

PAulyhoffman said:
Perhaps tomorrow
Click to expand...
Click to collapse
Thank you!

PAulyhoffman said:
This is kennethpenn's stock system.img from BriefMobile. I deodexed the system and framework and rooted it.
Click to expand...
Click to collapse
Cold you also create a CWM update zip with this kernel? Would be so much easier to use it. [email protected]!

xploited said:
Cold you also create a CWM update zip with this kernel? Would be so much easier to use it. [email protected]!
Click to expand...
Click to collapse
If you want a cwm zip of the system it is basically the same thing as Kennethpenn's beta 4.5. IMO cwm is more of a PITA than fastboot ever will be.
I won't have to because faux123 already did HERE

PAulyhoffman said:
If you want a cwm zip of the system it is basically the same thing as Kennethpenn's beta 4.5. IMO cwm is more of a PITA than fastboot ever will be.
I won't have to because faux123 already did HERE
Click to expand...
Click to collapse
I have used faux's and edgan's kernels before but I thought it would be nice to have a clean stock one as well in case I need it. (I often revert back and forth between stock and custom stuff).
Anyway, I thought your's is the closest to stock but with deodex and root.
If you say kenneth's is pretty much the same, I will use that.

Can this be flashed on a stock and locked ATRIX running 4.5.91 OTA to deodex using moto-fastboot?
I know it states in the OP to use moto-fastboot, but doesn't clarify if you need to be unlocked or not. I know you can use fadtboot to flash preinstall for root being locked but curious as to the system.img

SGTShark said:
Can this be flashed on a stock and locked ATRIX running 4.5.91 OTA to deodex using moto-fastboot?
I know it states in the OP to use moto-fastboot, but doesn't clarify if you need to be unlocked or not. I know you can use fadtboot to flash preinstall for root being locked but curious as to the system.img
Click to expand...
Click to collapse
You can install this in a rooted phone with locked bootloader
put the system.img on your device /sdcard/
Code:
adb shell
su
dd if=/sdcard/system.img of=/dev/block/mmcblk0p12

xploited said:
I have used faux's and edgan's kernels before but I thought it would be nice to have a clean stock one as well in case I need it. (I often revert back and forth between stock and custom stuff).
Anyway, I thought your's is the closest to stock but with deodex and root.
If you say kenneth's is pretty much the same, I will use that.
Click to expand...
Click to collapse
the link i gave was for Stock Kernel. Faux123 uploaded it. did you want a cwm of the system.img? Because yes kenneths is nearly the same.

PAulyhoffman said:
You can install this in a rooted phone with locked bootloader
put the system.img on your device /sdcard/
Code:
adb shell
su
dd if=/sdcard/system.img of=/dev/block/mmcblk0p12
Click to expand...
Click to collapse
Thanks. This will be my quick route to deodex!

I'm gonna try this tonight.
Sent from my MB860 using XDA App

i tried from fastboot and it says image is to large...

chaosjh said:
i tried from fastboot and it says image is to large...
Click to expand...
Click to collapse
You need to use moto-fastboot to flash this file.
Sent from my MB860 using XDA Premium App

Can you flash this on 2.2.2 gibgerblur?
Sent from my MB860 using XDA App

Hm...I can only install this through moto-fastboot? Can I install this zip through CWM?
Edit: so nevermind. I was able to install this but I am now missing the settings? Don't know what else could be missing. Any thoughts ?
Edit: Nevermind...I guess it was just a bad flash. I re-flashed it and everything is normal again. Thanks

Exactly what I was looking for. Installed this over rooted stock GB.
@filmusikat After digging around a bit, I decided skipping the moto-fastboot erase recovery command. Just flashed it over the existing system.img. Thanks again!

ghost_og said:
Exactly what I was looking for. Installed this over rooted stock GB.
@filmusikat After digging around a bit, I decided skipping the moto-fastboot erase recovery command. Just flashed it over the existing system.img. Thanks again!
Click to expand...
Click to collapse
Hey let me know which themes work for u... cuz not all the 4.5.91 themes work for this... when I flashed most of them on this... some things disappeared... like settings..and the camera... pretty weird?
Sent from my MB860 using Tapatalk

[ROM] XT883 Rom v60.3.250 Android v2.3.6 (upload 1/13/2013 ROM v60.3.250)

XT883 ROM SOLANA_SLNCT-57.1.60
http://www.multiupload.com/M15LSXNPOU(thank LaZiODROID uploaded)
Here is another mirror containing the XT883 Fastboot, 60.3.250 OTA, RSDlite, and motofail root.
http://dl.dropbox.com/u/71053731/XT883 Files.zip(thank RWALEY reupload)
v60.3.250 fully rom
http://www.kuaipan.cn/file/id_108891826273910787.htm
Enable GSM/wcdma:
edit file
\System\etc\motorola\com.motorola.android.providers.settings\settings.mkitso
enable_icc_type_restriction=1 -> enable_icc_type_restriction=0
boot in stock recovery,wipe.
restart.
RSD Lite v5.6
http://www.multiupload.com/DOCGHV98OM
Google Mobile Service Package Full Version for XT883
(need flash via recovery mode x+Power):
http://depositfiles.com/files/wwknt3bga
GAPP simplify edition (thanks #65 The Solutor upload):
http://www.multiupload.com/QHFKX161FE
XT883 Rom Benefits:
Moto Phone Portal
Call Firewall
Call Record
menu+power to screenshot
FM Radio
Hardware Decoding
Transfer any format file like Apk via Blurtooth
SMS received time shown was each other sent time.
you will enjoy it.
you need install morelocale to change to your Country and Language,then reboot droid3.
Root Tools:motofail root
Verizon Boot Animation:
http://www.megaupload.com/?d=1ST5WZMG
decompression
replace the same files in /system/media/
Change file-permission to rw-r-r
delete downanimation
Verizon Forest Wallpaper
http://www.megaupload.com/?d=QLN9XDS8
ME863/XT860 look here
http://forum.xda-developers.com/showthread.php?t=1288823

No idea how to download that file - could you up it somewhere a bit more....readable?

The 2 grey buttons between the green and blue buttons, by clicking any of them will start downloading straight away.

anyone able to download this?
http://translate.googleusercontent....1.html&usg=ALkJrhjD-vL8FcLruBRJzwHjSXGwKcwkRA
I think it may be along the same lines as the above file, but for the xt862

Android 2.3? I thought droid 3 already comes with 2.3.4?
Sent from my DROID3 using xda premium

slvrarrow said:
anyone able to download this?
http://translate.googleusercontent....1.html&usg=ALkJrhjD-vL8FcLruBRJzwHjSXGwKcwkRA
I think it may be along the same lines as the above file, but for the xt862
Click to expand...
Click to collapse
no,this rom is for me863,only be used for wcdma&gsm , no cdma2000
and no one flash this rom,may be get your droid3 brick

Can you give any more detail about this file?
Sent from my DROID3 using XDA App

sorry, thought it may be of use! is it a little odd these recovery files for fastboot arent in sbf format? maybe the usual `leakers' are looking for sbfs when these zip's may do the same job?
again im pretty rookie but trying to help. cheers

mvp3 said:
http://www.115.com/file/clf4iza2#SOLANA_SLNCT-57.1.40_Fastboot-service.xml.zip
Click to expand...
Click to collapse
Did anyone manage to snag this while the link was good?

rynosaur said:
Did anyone manage to snag this while the link was good?
Click to expand...
Click to collapse
Its not for our phone. Dont bother.

So? We still want a copy...

rynosaur said:
Did anyone manage to snag this while the link was good?
Click to expand...
Click to collapse
psouza4 said:
So? We still want a copy...
Click to expand...
Click to collapse
Sorry, i thought we had that file weeks ago.

@Suzook - are you refering to this chinese debug SBF linked by royolpunk?
http://forum.xda-developers.com/showpost.php?p=16649064&postcount=1
Surely this one
http://forum.xda-developers.com/showpost.php?p=17282326&postcount=4
is the more promising of the 2?
If that's a fully restorable system, we could swap out the radio image for the one in the OTA update, and the system image could be anything we want, right?
Or will the system image need to be signed for this to work?

apologies pressing save many too much

very sorry duplicate

mvp3 said:
china smuggled goods seller pay for get the modified from XT883 ROM for Chinesizing verizon droid3,It's just hearsay.
Click to expand...
Click to collapse
Oh Google Translate, thank you many kindnesses for your nonsensing translated!!!
thingonaspring said:
If that's a fully restorable system, we could swap out the radio image for the one in the OTA update, and the system image could be anything we want, right?
Or will the system image need to be signed for this to work?
Click to expand...
Click to collapse
Changing the .zip will make it unflashable in stock recovery, unless someone has a key signer for a Droid3 . . . and I'm guessing not Or is this truly something that will work with
Code:
moto-fastboot flashall
However, if an enterprising individual were to flash the stock update/ROM in recovery, then manually flash our radio in fastboot, they might not end up with a brick.
...maybe . . . my recovery is iced, so it won't be me trying

I can't flash the update in recovery :/ otherwise I would try. I do have recovery access though. Wonder if swapping out portions of that xt862 file may be possible..? We need someone with the knowledge!

slvrarrow said:
I can't flash the update in recovery :/ otherwise I would try. I do have recovery access though. Wonder if swapping out portions of that xt862 file may be possible..? We need someone with the knowledge!
Click to expand...
Click to collapse
Just like with the other SBF, do not flash it. Stop thinking about flashing it. Stop thinking about thinking about flashing it. In the best case, you will brick your phone until we get an SBF. In the worse case, the Chinese government is already en route to your location.
DO NOT FLASH THIS SBF!

Adam.h.ogle said:
Just like with the other SBF, do not flash it. Stop thinking about flashing it. Stop thinking about thinking about flashing it. In the best case, you will brick your phone until we get an SBF. In the worse case, the Chinese government is already en route to your location.
DO NOT FLASH THIS SBF!
Click to expand...
Click to collapse
LOL I don't think the Chinese government could do anything about it if we tampered with this
Sent from my DROID3 using xda premium

I wont don't worry just wondering about possibilities

Atrix HD FXZ's released. Thank you Firmware Team!

Source: http://sbf.droid-developers.org/dinara/list.php
Thank you very much to Pzyduck and his firmware team for finding and leaking these FXZ's for the Atrix HD to us to use!
DO NOT FLASH AT&T ON BELL AND VICE-VERSA!
AT&T FXZ-> http://sbf.droid-developers.org/dinara/7.7.1Q-115_MB886_FFW-14_SIGNED_CFC.xml.zip
System Version: 77.10.16.MB886.ATT.en.US
Bell FXZ-> http://sbf.droid-developers.org/dinara/7.7.1Q-115_MB886_BELL_FFW-12_SIGNED_CFC.xml.zip
System Version: ???
You can find the 32 bit Motorola USB Drivers here:
http://rootingmydroid.com/FILESYSTE..._End_User_Driver_Installation_5.9.0_32bit.msi
And 64 bit here:
http://rootingmydroid.com/FILESYSTE..._End_User_Driver_Installation_5.9.0_64bit.msi
RSD Lite 5.7 for flashing these can be found here:
http://rootingmydroid.com/FILESYSTEM/DEVELOPMENT/UDPATES/-RSD-LITE/RSDLite57.zip
Happy flashing... make sure that you have plenty of battery life before attempting this or you are using a Motorola Factory-style cable.

mattlgroff said:
Source: http://sbf.droid-developers.org/dinara/list.php
Thank you very much to Pzyduck and his firmware team for finding and leaking these FXZ's for the Atrix HD to us to use!
AT&T FXZ-> http://sbf.droid-developers.org/dinara/7.7.1Q-115_MB886_FFW-14_SIGNED_CFC.xml.zip
System Version: 77.10.16.MB886.ATT.en.US
Bell FXZ-> http://sbf.droid-developers.org/dinara/7.7.1Q-115_MB886_BELL_FFW-12_SIGNED_CFC.xml.zip
System Version: ???
You can find the 32 bit Motorola USB Drivers here:
http://rootingmydroid.com/FILESYSTE..._End_User_Driver_Installation_5.9.0_32bit.msi
And 64 bit here:
http://rootingmydroid.com/FILESYSTE..._End_User_Driver_Installation_5.9.0_64bit.msi
RSD Lite 5.7 for flashing these can be found here:
http://rootingmydroid.com/FILESYSTEM/DEVELOPMENT/UDPATES/-RSD-LITE/RSDLite57.zip
Happy flashing... make sure that you have plenty of battery life before attempting this or you are using a Motorola Factory-style cable.
Click to expand...
Click to collapse
I am new to motorola phones. Can someone explain what this is?
A leaked update? Is this version rootable? And on that note, is an unlocked bootloader required for root?
Sent from my phone.

Markyzz said:
I am new to motorola phones. Can someone explain what this is?
A leaked update? Is this version rootable? And on that note, is an unlocked bootloader required for root?
Sent from my phone.
Click to expand...
Click to collapse
Firmware Stock/Official :good:
Thanks you matt
MIRROR: http://forum.xda-developers.com/showthread.php?p=30714649#post30714649

Markyzz said:
I am new to motorola phones. Can someone explain what this is?
A leaked update? Is this version rootable? And on that note, is an unlocked bootloader required for root?
Sent from my phone.
Click to expand...
Click to collapse
These are files that can be used to truly factory restore your phone. If you had a custom rom installed, this would put you back to stock.
You use Motorola's RSD Lite program to flash to your phone while it is in AP Fastboot mode.
This will work on locked bootloaders because they are signed files from Motorola meant for flashing in this way.
EDIT: As Pzyduck says above, these are official firmware not leaks

Don't flash AT&T on Bell or vice versa, you may get trapped because of secure versions.
(btw. I know, it's codenamed qinara, and not dinara, but meh, too lazy to fix it )

Skrilax_CZ said:
Don't flash AT&T on Bell or vice versa, you may get trapped because of secure versions.
(btw. I know, it's codenamed qinara, and not dinara, but meh, too lazy to fix it )
Click to expand...
Click to collapse
If you look inside the files themselves Motorola was too lazy to fix it too! They use both throughout lol.

Thanks to mattlgroff for posting here
---------- Post added at 04:03 AM ---------- Previous post was at 04:01 AM ----------
Pzyduck said:
Firmware Stock/Official :good:
Thanks you matt
MIRROR: http://forum.xda-developers.com/showthread.php?p=30714649#post30714649
Click to expand...
Click to collapse
Can these files be modded to allow root before they are installed on the phone?

reddog said:
Thanks to mattlgroff for posting here
---------- Post added at 04:03 AM ---------- Previous post was at 04:01 AM ----------
Can these files be modded to allow root before they are installed on the phone?
Click to expand...
Click to collapse
On 2 accounts we wouldn't be able to do this.
1) The phone will only take signed images for system in AP Fastboot. There are sig checks on flashing and on boot (we can assume this, we can test more obviously since we have FXZ backups).
I didn't want to test flashing a rooted system dd'd out before because we had no FXZ's to test. Now that we have them it might be worth it to try it out. Worst case use these FXZ.
Rooted system.img: you can get the entire partitions here which includes it: http://crackflasher.com/dev/mattlgroff/MB886.ATT.en.US/AtrixHdPartitions.zip
Be extra careful flashing things you do not have backups for...
2) The system.img.ext4 file inside of these are not only compressed, but appear to be encrypted as well.

mattlgroff said:
On 2 accounts we wouldn't be able to do this.
1) The phone will only take signed images for system in AP Fastboot. There are sig checks on flashing and on boot (we can assume this, we can test more obviously since we have FXZ backups).
I didn't want to test flashing a rooted system dd'd out before because we had no FXZ's to test. Now that we have them it might be worth it to try it out. Worst case use these FXZ.
Rooted system.img: you can get the entire partitions here which includes it: http://crackflasher.com/dev/mattlgroff/MB886.ATT.en.US/AtrixHdPartitions.zip
Be extra careful flashing things you do not have backups for...
2) The system.img.ext4 file inside of these are not only compressed, but appear to be encrypted as well.
Click to expand...
Click to collapse
Any luck flashing this yet?

popfan said:
Any luck flashing this yet?
Click to expand...
Click to collapse
No one's tried to my knowledge, also the system.img.ext4 is not encrypted, but its compression methods are unknown.

mattlgroff said:
No one's tried to my knowledge, also the system.img.ext4 is not encrypted, but its compression methods are unknown.
Click to expand...
Click to collapse
i tried but nothing. only error when installing

There is a new firmware listed as MB886_att-user-4.1.1-9.8.0Q-97_MB886_FFW-20-27-release-keys-ATT-US_BuildA.xml.zip has anyone tried to to flash this yet? Is this 4.1.1 OTA that we have now? I need to know because like an idiot I tried to flash back to 4.0.4 from 4.1.1 and now it fastboots on every reboot. Super annoying. Anyway I need to flash to 4.1.1 to fix this apparently.

Tried it says unknown command flash failed unknown flash boot command so u can try but no good phone still OK so I got lucky
Sent from my MB886 using xda app-developers app