I have got Nv_data.bin from my phone and opened it with Hex Workshop, and gone to 0x181468.
This is apparently supposed to be FF 01 ... when the phone is locked, and you change it to FF 00 00... ... but mine is already FF 00 00 00 00 46 46... but the phone is still locked (says emergency calls only with sim from different network.)
It is locked to orange UK FWIW.
check your IMEI number matches the number on the box / phone
theres a small chance it could of got corrupted with playing with the Nv_data.bin files
The IMEI under anroid settings is the same as printed on the phone. If you mean within the file then you will have to let me know how to find it?
I haven't done anything to the file yet except copy it.
?? what to do ??
Related
Hi,
I intend to flash a cooked ROM (ITsPapa20748) to my Herald. From reading some sticky posts here I learned that at first I have to install a hacked bootloader - so I downloaded HardSpl_WM6.rar
My procedure was as follows:
1. install canonyang, ASerg_Policies and Disable_Security (in this order)
2. softreset
3. start RUU
My mobile then enters bootloader mode and ends up with error message "Error [270]: Update Error" (progress bar freezes at 3pct)
My config is as follows:
PC: is running WindowsXP (with SP2), ActiveSync v4.5 is in Guest Mode
Mobile: Model-Nr. Hera100
ROM version 4.17.402.102 GER
IPL 4.17.0001
SPL 4.17.0000
I had to UNcheck the start/system/advanced_networking-box in order to establish USB-connection.
After spending some hours going through existing threads I'm pretty sure that this is a common situation. But I didn't find any hint that helped me to flash successfully.
So any comments and suggestions are welcome.
thx!
1aladdin1
it works now
sorry for posting too early - now it worked.
I basically performed the same steps as listed in my previous post. Two differences:
1. softreset between installation of canonyang/aserpolicy/disable_security
2. while performing the RUU I had FILEMON running (a great tool from mark russinovich)
Finally I don't know, which step was the decisive one - bot anyhow it works now.
Hope this helps other guys in a similar situation.
please guys help me
my htc touch p3452 is dead becoz i flash but something is wrong and then it was dead now it will on on bootloder mode(red,green,blue) here is my detail please tell ,me what to do
it show..
IPL 3.07.0002
SPL 3.07.0000
DEVICE ID= ELF010050
CID= DOPOD001
45 4C 46 30 31 30 30 35 30 00 00 00 00 00 00 00 ELF010050.......
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
44 4F 50 4F 44 30 30 31 00 00 00 00 00 00 00 00 DOPOD001........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 ..............
i also tryed to flash "DID-ELF010050_CID-DOPOD001_ROM-2.20.721.2B" but is not flashed it gave "error 270 update error" something please tell me where is the problem and how to solve please guys
Wwwwwweeeellllllll....YOU HAVE AN ELF, NOT A HERALD. Seriously, if you tried to HardSPL your Elf with the Herald HardSPL...I don't even know. These are the Herald forums, NOT the Elf forums, as such, more than likely no one that frequents here will know what to do to help you.
use for rewrite ESN and flash ROMs. good luck.
rename it to .rar, its a winrar file.
MOD EDIT - Removed file. PM me if you disagree and provide me with more history/evidence
Leave it. He has 1 post and the SPL hasn't been cracked yet. Probably a scam.
I have re-opened this thread.
@ ls1024 - Feel free to modify first post again and provide more info including what you showed me in PM
Rick
Thanks Spartan for looking at this. Hopefully once he posts more info it will be what we Imagio users are desperate for, or a step in that direction.
Narcotichobo said:
The linked thread reads as following:
Only 6975's with spl already unlocked can be flashed, before you flash please make sure your spl is unlocked.
Currently all chinese phones come unlocked.
To confirm, go into the three color screen (hold down the volume button and the device on button), spl should be 0.40.0000
After flashing check to see if the radio number is 2.05ESNWVL
The operation below is identical to the 6875 (TP2), if you have a problem refer to posts on 6875 (TP2) ESN post
Use any version of CDMA Work Shop
On the terminal page, commands section
27 97 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
After you press send the MEID should be cleared
Afterward you can write whatever ESN
When you finish you can flash any radio and won't lose the ESN
Reference: Tutorial on writing the 6875
http://www.diypda.com/viewthread.php?tid=92838&extra=page=1
Alright, I don't know how to do any of that stuff, but i'm 95% sure on the translation so I hope that helps someone who does know what they are doing!
Also there seems to be an attachment to the post in that thread but i can't access it because I am not a forum member, and registration requires an invitation number.
Click to expand...
Click to collapse
The 0.40 SPL comes on the Chinese version of the Imagio and it allows writing of the ESN and flashing.
All being chatted in this thread:
http://www.forum.ppcgeeks.com/showthread.php?t=97542
Cmonex is working on the HSPL ATM and I do believe it will be based off of the 0.40 SPL
Americanmetal said:
The 0.40 SPL comes on the Chinese version of the Imagio and it allows writing of the ESN and flashing.
All being chatted in this thread:
http://www.forum.ppcgeeks.com/showthread.php?t=97542
Cmonex is working on the HSPL ATM and I do believe it will be based off of the 0.40 SPL
Click to expand...
Click to collapse
Woot I got quoted here.
\/
||
||
\/
And this helps us .38 how?
I think I read this over at PPCG but no instructions on how to do it on a .38 SPL so basically this is for the .40 Imagio only correct?
I posted both modified radios for TP2 and Imagio on PPCG and also a utility to write MEID/ESN (all 3 files from diypda china)
narcotichobo said:
Woot I got quoted here.
Click to expand...
Click to collapse
I had to get this thread unlocked rofl
Still, how can we upgrade to .40? That's what's holding us from at least changing radios to chinese ones hehehe
ls1024 said:
use for rewrite ESN and flash ROMs. good luck.
rename it to .rar, its a winrar file.
MOD EDIT - Removed file. PM me if you disagree and provide me with more history/evidence
Click to expand...
Click to collapse
i have pm...tks.
Ignore this
Here is a couple of files I got from chinese DIYPDA forum. One is a modified radio and the other one a program to simplify the esn repair.
Click to expand...
Click to collapse
Here is the modified radio and DFS, a program that does let you change MEID and/or ESN for when we can do it. Only .40 can change to this radio
Code:
http://www.mediafire.com/?bxjnytljdid
http://www.mediafire.com/?zmtjymhzcjf
we upgrade to 0.40? is the focus of
At least if we can do the .40 upgrade then we can also upgrade to an HSPL that allows unsigned ROMs. Has anybody had any luck with .40? I would like .40 on my phone... And also a way to go back to .38 if possible!
Well, easiest way to go .40 is to buy an Imagio that's .40 already.
taobao(dot)com as specified by our friends at diypda(dot)com has them for 3150 = $461 usd. The question is... If we get this phone and we flash the Imagio shipped rom, will it flash .38 spl or leave it at .40 spl?
It will replace to .38 ,
u must delete SPL from the ruu_signed.nbh
m4f1050 said:
Well, easiest way to go .40 is to buy an Imagio that's .40 already.
taobao(dot)com as specified by our friends at diypda(dot)com has them for 3150 = $461 usd. The question is... If we get this phone and we flash the Imagio shipped rom, will it flash .38 spl or leave it at .40 spl?
Click to expand...
Click to collapse
Hmmm, well, at least the .40 can flash it after you remove .38 spl (will be unsigned afterwards) so how do you remove it? I've cooked ROMs with kitchens before but I have no clue how to remove the SPL from the .nbh
htcRIE_0.5.0.12
m4f1050 said:
Hmmm, well, at least the .40 can flash it after you remove .38 spl (will be unsigned afterwards) so how do you remove it? I've cooked ROMs with kitchens before but I have no clue how to remove the SPL from the .nbh
Click to expand...
Click to collapse
I'll give it a test drive to see how it works. Link here: http://forum.xda-developers.com/showthread.php?t=377514
I tested program, it does work, I managed to remove SPL from the Verizon .nbh but Whitestone is not on the list of selected phones, not sure what that list/dropdown menu is for, is that for signing the ROM?
Imagio ROM Test
I have an Imagio, I am willing to use as Genie Pig if anyone can point me to promising ROM to test out. I'm willing to chance bricking the phone. It has been replaced by a new phone from Verizon.
Thanks for gruptnt,I finally figure out the reason is not eeprom.I think the wifi antena is loose when my phone droped from 1.7 meter a few days ago.So the people who have a familar wlan issue can try this method.And thanks gruptnt again for his kind help.Now the thread can be closed!
Hi，recently I have flashed my diamond to stock wm 6.1 ROM.When it finished,I found My WLAN is also finished.
The problem was just the same as the video below:
http://www.youtube.com/watch?v=G_jQc1JRGQI
I seach all of the froum and found a possible reason--I have erased my eeprom during the flashing.Solution for herme and trinity have been found.However,I can't locate the mac address of wlan and there is no working waln diamond to dump the eeprom.Sorry for my bad english ,hope some one can solve this problem.
Here is herme thread:
http://forum.xda-developers.com/showthread.php?t=322225
Here is trinity thread:
http://forum.xda-developers.com/showthread.php?t=490681
Hi,
very strange. Usually, it does not happen when flashing.
Which Diamond you flashed?
If it is a Dopod D900 from China, it does not have the WLAN chip at all, like all Dopod with WM6.x officially sold in China. So, even if you find out how to change EEPROM and add a mac-address it will not work. (btw, Dopod S900 also misses the front camera)
Which ROM you had before and which (stock) ROM you flashed?
How did you flash? With mtty?
Do you still have the same problem when changing back to previous ROM?
Good luck!
Huckleberry88 said:
Hi,
very strange. Usually, it does not happen when flashing.
Which Diamond you flashed?
If it is a Dopod D900 from China, it does not have the WLAN chip at all, like all Dopod with WM6.x officially sold in China. So, even if you find out how to change EEPROM and add a mac-address it will not work. (btw, Dopod S900 also misses the front camera)
Which ROM you had before and which (stock) ROM you flashed?
How did you flash? With mtty?
Do you still have the same problem when changing back to previous ROM?
Good luck!
Click to expand...
Click to collapse
I use HTC WCDMA version(DIAM100) and it has a WLAN chip and front camera.
I have always been using Donsalari TFL2.1ROM (just show in my signature) before.
Just a few days ago I flashed "RUU_Diamond_HTC_WWE-AFK_2.03.421.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship" which I download from HTC offical website using my own S/N.
Of coure I use mtty's task 29 command before flashing.However It failed first time.So I change my SPL from Olinex 1.93 to stock 1.93 .The I just run the exe file I downloaded tiwce to make it work(the first flashing is unsuccessful but it changde my SPL from stock 1.93 to 2.03,and the second time was succcessfull).After flashing,My WLAN dead as shown in the video in the first post.
Yes,I change it to previous ROM but no miracle happened.I also change different radio and SPL but it didn't work.
Finally,I search the entire thread and found it could be the eeprom problem,but I don't found any solution to diamond just like herme and trinity.
Lastly,Thank you for your kind help.
In that case, if you have the original ROM with spl and radio installed, then maybe best chance is to check with the HTC service to help you to sort it out.
As you mentioned the problem with the missing mac-address happened to some other phones but I never heard it happens to a Diamond before.
Good luck!
Huckleberry88 said:
Hi,
very strange. Usually, it does not happen when flashing.
Which Diamond you flashed?
If it is a Dopod D900 from China, it does not have the WLAN chip at all, like all Dopod with WM6.x officially sold in China. So, even if you find out how to change EEPROM and add a mac-address it will not work. (btw, Dopod S900 also misses the front camera)
Which ROM you had before and which (stock) ROM you flashed?
How did you flash? With mtty?
Do you still have the same problem when changing back to previous ROM?
Good luck!
Click to expand...
Click to collapse
Huckleberry88 said:
In that case, if you have the original ROM with spl and radio installed, then maybe best chance is to check with the HTC service to help you to sort it out.
As you mentioned the problem with the missing mac-address happened to some other phones but I never heard it happens to a Diamond before.
Good luck!
Click to expand...
Click to collapse
Thank you guy,I think I will live with it cause I do not use wlan very often.And Diamond is old enough nowdays.If microsoft publish a chiense version of windows phone 7,I'll consider to buy one to replace my diamond.
jent.le said:
Hi，recently I have flashed my diamond to stock wm 6.1 ROM.When it finished,I found My WLAN is also finished.
The problem was just the same as the video below:
http://www.youtube.com/watch?v=G_jQc1JRGQI
I seach all of the froum and found a possible reason--I have erased my eeprom during the flashing.Solution for herme and trinity have been found.However,I can't locate the mac address of wlan and there is no working waln diamond to dump the eeprom.Sorry for my bad english ,hope some one can solve this problem.
Here is herme thread:
http://forum.xda-developers.com/showthread.php?t=322225
Here is trinity thread:
http://forum.xda-developers.com/showthread.php?t=490681
Click to expand...
Click to collapse
U can see at this
http://forum.xda-developers.com/showthread.php?t=597195
Note :
i have another diamond with wlan problem (can't go on) but when i have disassembly diamond the cable of antenna wlan were disconnected on mainboard
i have reconnect and now wlan is ok
; said:
U can see at this
http://forum.xda-developers.com/showthread.php?t=597195
Note :
i have another diamond with wlan problem (can't go on) but when i have disassembly diamond the cable of antenna wlan were disconnected on mainboard
i have reconnect and now wlan is ok
Click to expand...
Click to collapse
Thank you dude.I see your work on trinity,but i don't see the thread above.Thank very much for your kind help.I will try it later,and I will post the result.Thanks again,gtuptnt.
gruptnt said:
U can see at this
http://forum.xda-developers.com/showthread.php?t=597195
Note :
i have another diamond with wlan problem (can't go on) but when i have disassembly diamond the cable of antenna wlan were disconnected on mainboard
i have reconnect and now wlan is ok
Click to expand...
Click to collapse
Hi,dude.I try your method,but no luck.Since I am at school,I can not find my mac address in router log file.I have used 56 48 65 48 22 00 which I find in supersport's video.
I use mtty's info 8,and find BLOCK 951 (0x3B7) is bad block ,however，it does exist when I use task 29 before flashing.
After using task 37 ff in mtty I got:
AA0EFF80: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFF90: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFFA0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFFB0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFFC0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFFD0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFFE0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
AA0EFFF0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 | ................
Click to expand...
Click to collapse
And no signature in the end.Any idea？
Hi. I am a sgs user living in vietnam struggling to restore my imei.
Okay, you guys can blame me.
I removed my efs folder accidently without backup.
Here is what’s going on.
My phone works perfectly on any froyo roms but not on eclairs.
When I check my product code with sgs tools, I see “Not Active” instead of product code.
And, of course, I’ve got this so called generic imei.
I checked my nv_data.bin with Ultraedit and here is what it shows
00188000 ff ff ff ff 52 45 56 5f ….REV_
00188008 5f 00 00 00 00 00 47 58 _.....GX
00188010 53 4f 00 00 00 00 4e 6f SO….No
00188018 74 20 41 63 74 69 76 65 t Active
00188020 00 58 53 4f 00 00 00 00 .XSO….
I know it looks very abnormal…..
Is there anyone who has any ideas about imei and product code restore?
(In windows registry, my product code had been I9000HKAXSO before it went bad)
I really want to restore my imei so I can bring my phone over to Germany!!!
It's not possible without a backup.
send it to Samsung . They can fix it with a fee
thank you for your reply. i am going to give away my sgs to sammy service center.
Before you do that search the forum their are a large number of posts on the topic including some fixes .Longshot but worth a try .
jje
So I have CWM, a 4.2.2 ROM On this phone, but whenever I turn it on with a different SIM Card than the phone is accepting, it asks me for a SIM network Unlock PIN.
I found this thread:
http://forum.xda-developers.com/showthread.php?t=939752
Where it says to edit the /efs/nv_data.bin file and change it from FF 01 00 00 00 00 46 46 46... and change the 01 to 00. When I tried to edit it in a Hex Editor, the 01 was already 00. So that should mean that it's already unlocked right? What can I do to unlock this phone?
Image from Hex editor (to make sure I'm editing the right part):
http://i.imgur.com/F0jMO0x.png
ROM: http://forum.xda-developers.com/showthread.php?t=1878961&highlight=cm+10+1
Career: T-Mobile.
Thank you.
same issue
Aman1238 said:
So I have CWM, a 4.2.2 ROM On this phone, but whenever I turn it on with a different SIM Card than the phone is accepting, it asks me for a SIM network Unlock PIN.
I found this thread:
http://forum.xda-developers.com/showthread.php?t=939752
Where it says to edit the /efs/nv_data.bin file and change it from FF 01 00 00 00 00 46 46 46... and change the 01 to 00. When I tried to edit it in a Hex Editor, the 01 was already 00. So that should mean that it's already unlocked right? What can I do to unlock this phone?
Image from Hex editor (to make sure I'm editing the right part):
http://i.imgur.com/F0jMO0x.png
ROM: http://forum.xda-developers.com/showthread.php?t=1878961&highlight=cm+10+1
Career: T-Mobile.
Thank you.
Click to expand...
Click to collapse
Hi I too have the same issue...it asks for the sim network unlock pin after update.
Can anyone help?