Related
I have my Kaiser upgraded from Abusalza ROM v7 to v10.
It works like a charm and I'm loving it so far until now.
The battery is dead and when I plugged in either usb charger or power charger, the notification led lit up solid orange/amber like it supposed to and then it blinks.
I checked and later found my phone isn't charging at all. Is this related to bad battery or is it because of incompatible radio?
Oh, and when I tried to switch on the device it just hang. Perhaps it doesn't have enough juice to boot up.
Anyone got same problem with me? Please advice how to fix this.
Thanks.
If you have already cleaned the battery terminals, I would suppose it is new battery time.
Well, I was sort of having a problem similar to this running the same ROM series. For me though, the notification LED would blink, even if it wasn't plugged in and there were no notifications. I would also get it when plugged in at times. This was intermittent, since it would randomly happen for some unknown reason. To fix it, I just killed all running programs, and reset the phone once or twice and it went away.
For you, if the ROM worked fine before, but isn't working now, a bad radio would not cause your problem. An incompatible radio would have caused you boot up problems and such from the moment you flashed, not later on. Don't know exactly what to tell you, except try a new battery. Get back to us after, and if it doesn't work, we can figure something else out. Hope your problem gets resolved by the battery.
Tilt Fanatic said:
Well, I was sort of having a problem similar to this running the same ROM series. For me though, the notification LED would blink, even if it wasn't plugged in and there were no notifications. I would also get it when plugged in at times. This was intermittent, since it would randomly happen for some unknown reason. To fix it, I just killed all running programs, and reset the phone once or twice and it went away.
For you, if the ROM worked fine before, but isn't working now, a bad radio would not cause your problem. An incompatible radio would have caused you boot up problems and such from the moment you flashed, not later on. Don't know exactly what to tell you, except try a new battery. Get back to us after, and if it doesn't work, we can figure something else out. Hope your problem gets resolved by the battery.
Click to expand...
Click to collapse
Keep in mind that my phone is currently out of juice i.e. dead.
So, supposedly by plugging in the charger I can restore the battery but in this case that didn't happen.
I guess I would better off go to the shop where I bought the battery and ask a replacement. The battery was new and not even 1 months old.
I will keep you posted. Thanks for the advice guys.
Does the LED light up still, even with the battery dead? If so, wait about 20 min for it to recharge, even though I am assuming you have already done this. If it is completely drained, it most likely won't power back until it has enough power to do so on it's own, even with the charger connected.
Tilt Fanatic said:
Does the LED light up still, even with the battery dead? If so, wait about 20 min for it to recharge, even though I am assuming you have already done this. If it is completely drained, it most likely won't power back until it has enough power to do so on it's own, even with the charger connected.
Click to expand...
Click to collapse
At first it blinking and then I pulled out the battery and reinsert it into the phone. Now it lit amber light and then in few minutes turned green. Tried to switch it on and the screen loading fine until at one time it show loading icon and then shutdown.
You assumed it right though, I've been letting the phone connected to the charger since last night and still no juice pumped into the battery I presume as I can't turn it on.
I agree with WillardZ
nyunyu said:
I guess I would better off go to the shop where I bought the battery and ask a replacement. The battery was new and not even 1 months old.
Click to expand...
Click to collapse
There's a technical term for items which fail very early on called infant mortality - this may be whats happened. See how it goes with a battery swapped in the shop. If you can get it to work by putting in a fully charged, known good battery but the recharging function doesn't work (or you get a flashing red light after a few minutes again), also try cleaning the spring terminals with IPA or contact cleaner applied using cotton buds. If that still doesn't work but you can boot the device into windows (with the shop borrowed battery), perform a hard reset before the battery goes flat/below 50 % and test again.
okay, I found my other battery which is I know work fine and put it in the device.
I charge it to full and now turning the device on.
While loading the touchflo, the loading icon just hang and I can't do anything.
Nothing works except sleep button.
Can you advice me how to reset this thing?
I know that battery isn't the problem here and I can't seems to do anything since it hung on me.
Oh, I tried turning the phone on without SIM and memory card and still hung.
nyunyu said:
okay, I found my other battery which is I know work fine and put it in the device.
I charge it to full and now turning the device on.
Click to expand...
Click to collapse
hmmm, wonder why you didn't try that at the first hint of a suggestion it's a dodgy battery
While loading the touchflo, the loading icon just hang and I can't do anything.
Nothing works except sleep button.
Can you advice me how to reset this thing?
Click to expand...
Click to collapse
I can but it'll encourage others to ask without searching first and given there's already a wiki here that covers Kaiser Resets perfectly well (and the Kaiser users manual that comes with the device - let me guess, you don't have that), you'll need to read the wiki and help yourself.
Flying Kiwi said:
hmmm, wonder why you didn't try that at the first hint of a suggestion it's a dodgy battery
Click to expand...
Click to collapse
Not to sound rude but I did said that I 'found' my other battery which is previously misplaced whereas I said earlier I'm going to get a replacement for the dead battery.
Flying Kiwi said:
I can but it'll encourage others to ask without searching first and given there's already a wiki here that covers Kaiser Resets perfectly well (and the Kaiser users manual that comes with the device - let me guess, you don't have that), you'll need to read the wiki and help yourself.
Click to expand...
Click to collapse
There is an instruction of how to reset the kaiser but is there a way to reset it while it is OFF or HANG?
I honestly apologies if I sound like I asked question without searching first but I honestly did not found what I'm looking for. The pda is still hang no matter how many times I restart it and I'm out of idea.
nyunyu said:
Not to sound rude but I did said that I 'found' my other battery which is previously misplaced whereas I said earlier I'm going to get a replacement for the dead battery.
There is an instruction of how to reset the kaiser but is there a way to reset it while it is OFF or HANG?
Click to expand...
Click to collapse
duuuuudddeee....the page you linked to above describes a way to do a HARD RESET for your EXACT requirement...read it again.
also, if it is OFF to begin with, then powering it up (even if it hangs ultimately) is equivalent to a SOFT RESET. if it doesn't complete startup and always hangs, then a HARD RESET is the way to go.
I honestly apologies if I sound like I asked question without searching first but I honestly did not found what I'm looking for. The pda is still hang no matter how many times I restart it and I'm out of idea.
Click to expand...
Click to collapse
and if by "reset it", you mean "flash a new ROM", you can search for that also and you'll find plenty of guides and tutorials and FAQs...but go one step at a time and do a hard reset first (remember, you will lose all data and non-default programs after the hard reset).
ASCIIker said:
duuuuudddeee....the page you linked to above describes a way to do a HARD RESET for your EXACT requirement...read it again.
also, if it is OFF to begin with, then powering it up (even if it hangs ultimately) is equivalent to a SOFT RESET. if it doesn't complete startup and always hangs, then a HARD RESET is the way to go.
and if by "reset it", you mean "flash a new ROM", you can search for that also and you'll find plenty of guides and tutorials and FAQs...but go one step at a time and do a hard reset first (remember, you will lose all data and non-default programs after the hard reset).
Click to expand...
Click to collapse
Thanks!
I just noticed the part where it says power+camera+stylus.
Appreciate that a lot.
nyunyu said:
I just noticed the part where it says power+camera+stylus.
Click to expand...
Click to collapse
You've found the right section but just the hard reset section will be applicable. You don't need the bootscreen (which is what that button combination is all about), just a hard reset (making sure the battery has a decent charge of at least 50% before starting).
Thank you for all the help.
I've managed to reset my phone back to OEM and then flash 3.34 hardspl and radio and abusalza v10. Looks like it back functioning.
Will monitor it to see what could be wrong in these few days.
i finally get my SGS back to JM1, install the voodoo lagfix + colour fix (which im now looking to remove as it does wierd things to my screen, the colour fix not the lagfix). anyway i thought i had it set-up perfectly, then i put it on charge last night at some point it hit the 100% charge and then 5-10 mins later it turned off (as in completly turned off), as i use this phone for daily alarm/diary etc this is obviously quite a shock that the alarm no longer functions if the phone is off, i know sony and nokia and htc's will all still work in these circumstances, due to this i missed a very important meeting.
so how can i fix this, firstly i want it to stop turning off on full charge (it used to just stay on), if this is not an option i want to make it so the alarm goes off, even if the phone is off,
I just tested it and the alarm of my gt-i9000 doesn't work either, when the phone is turned off. Pretty lame.
I have Froyo JPM with Chainfire's root
you would think it would as some things are important, im more worried that its turning itself off 5-10 mins after being fully charged, there is no setting for it either, so its a problem with the way the rom flashed.
i did a full clear and wipe of both sd, and cache from the recovery menu, and then i also formatted the int sd, when android booted to get rid of that annoying process error. so it cant be that. the only things i have installed are the apps i have paid for, and the lagfix, i never had this issue b4 when i did not use the lag fix, could it be that thats causing it.
after doing a little rerading.
I found a link about flashing roms and another about a 3 button download mode.. and that you should check that this mode works... before you even try to flash so after reading it I tried it out...
yes my unit showed the correct screen but thats a far as the topic went..
and thats exactly where my phone sat for quite a while, after about 5 minutes of this screen being on my hone it progressing I figured that since there was nothing for it to download that it would exit out after a few more minutes and not exiting I decided to remove the battery as nothing else seemed to work....
yes I did read do not turn off unit.. however I was not downloading anything as the sim was removed and the wifi was turned off on my router.. so I could not see that this would cause harm..
however now my phone is in a boot loop...
I pulled the batery for another 10 minutes and replaced still the same... can sombody please help me..
I have searched and found nothing....
Well I fixed my issue.. I went intothe recovery mode adn selected reboot system.. the top option.. and all is good.. I would have thought that removing the battery and restarting the system wouldhave been the same but it seems that the system must read stored info. on reboot..
Yay all good I feel I learned something...
Hey guys,
I could need a bit of help! It's now the third time I'm having this problem, don't ask me why. I've got the feeling that I read the whole forum here, but didn't find anything similiar.
The 1st time I didn't change anything (ok, rooted it, but nothing else)
The 2nd time I overclocked it slightly (~850-900 MHz)
Now I'm using MIUI.
But back to the problem:
I'm unable to use the keyboard, every time I'm sliding open the keyboard (even when it's turned off), it "crashes". The screen stops working or it freezes, the only way to turn it off is taking out the battery.
However, the bigger problem comes now: I'm barely able to restart it. It tries booting, but is restarting all the time or the screen is just turning on (in some angles you see that it is turned on but it's black). After many retries, it starts working, sometimes the bootloop is running 15min or i have to manually restart it 10 times or more. The strange thing is that the keyboard works fine, nevertheless I have to choose between using it opened (taking it with me becomes difficult ) or closed...
...the main problem now is flashing a new Rom, I'm currently trying it through the android sdk and adb, but using the power-button + x is easier
I don't think that I can solve the problem, I sent the device two times back (warranty till may 2012), but maybe someone here knows a bit more. My guess is that one of the sensors is broken, or some parts of the display that should manage the sliding process...
Anyway, thanks for your attention!
Web
If you already have Rom Manager, just click Reboot into Recovery..
inches0 said:
If you already have Rom Manager, just click Reboot into Recovery..
Click to expand...
Click to collapse
Tried to use one a time ago, but it wasn't working right....
However, now I'm not even able to boot it, the screen just flashes and turns off itself before trying to restart a few moments later....guess I lost my Milestone
Sbf back to stock?
taptaptouch said:
Sbf back to stock?
Click to expand...
Click to collapse
the computer isn't finding it anymore...I'll back up the data and try use my warranty... I hope that they don't complain about MIUI...
But I'm still not getting the point, why my mobile had these issues three times, although they "repaired" it twice...and nobody else is having the same problem
I have the feeling I'm going to get repetitive here guys, but I've been reading the troubleshooting threads for over an hour and couldn't find an answer to help me.
Last saturday I was to lazy to move from the couch, so I watched as my S3 Mini ran out of battery. I got the "phone is turning off" screen as usual. Later I went to bed, but as I needed my alarm to go off in the morning I tried turning it on again, and nothing* happened. Plugged it on the wall, nothing*. Replaced the battery, nothing*. Gave it a good half hour plugged, and as you can guess, nothing*.
* when I say nothing, I mean it won't light up, won't vibrate, won't wink for me, won't load any kind of error, it's actually just like if you were trying to turn on a phone without any battery connected, no grasp of life comes from its poor soul.
The only moment I could see some action on the device is when I tried connecting it on the PC a few hours ago, as it installed drivers to Windows. Right after installing the drivers however, it won't show in the file explorer. I've tried to detect it with a few development tools such as ORT and Odin and there was no sucess either. Download or Recover mode will not work as well.
One thing I think worth mentioning, is that ever since I rooted it a couple of years ago, whenever I tried to recharge it while it was off, the standard "green charging battery" would never appear. What would appear on the screen was a freezed loading icon (the one that keeps roling again and again, but frozen). This particular issue never came off, even reseting it or installing new ROMs.
I always used Maclaw's, some of the latest 4.x, because I tought the 5.x was to heavy for the s3 minis.
I've read some about USB JIGs and stuff, but what makes me very curious is what the heck?! The phone was working just fine, the battery runs out and I have a brick? Is this possible? Can anyone tell me any work around?
I apologize for possible grammar mistakes.
ScrewedImei said:
I have the feeling I'm going to get repetitive here guys, but I've been reading the troubleshooting threads for over an hour and couldn't find an answer to help me.
Last saturday I was to lazy to move from the couch, so I watched as my S3 Mini ran out of battery. I got the "phone is turning off" screen as usual. Later I went to bed, but as I needed my alarm to go off in the morning I tried turning it on again, and nothing* happened. Plugged it on the wall, nothing*. Replaced the battery, nothing*. Gave it a good half hour plugged, and as you can guess, nothing*.
* when I say nothing, I mean it won't light up, won't vibrate, won't wink for me, won't load any kind of error, it's actually just like if you were trying to turn on a phone without any battery connected, no grasp of life comes from its poor soul.
The only moment I could see some action on the device is when I tried connecting it on the PC a few hours ago, as it installed drivers to Windows. Right after installing the drivers however, it won't show in the file explorer. I've tried to detect it with a few development tools such as ORT and Odin and there was no sucess either. Download or Recover mode will not work as well.
One thing I think worth mentioning, is that ever since I rooted it a couple of years ago, whenever I tried to recharge it while it was off, the standard "green charging battery" would never appear. What would appear on the screen was a freezed loading icon (the one that keeps roling again and again, but frozen). This particular issue never came off, even reseting it or installing new ROMs.
I always used Maclaw's, some of the latest 4.x, because I tought the 5.x was to heavy for the s3 minis.
I've read some about USB JIGs and stuff, but what makes me very curious is what the heck?! The phone was working just fine, the battery runs out and I have a brick? Is this possible? Can anyone tell me any work around?
I apologize for possible grammar mistakes.
Click to expand...
Click to collapse
try to plug in the phone into charger & leave it there like 20 mins or more. battery loads then.
then try access samsung download mode, if you cant the phone is probably useless (brick for ever) because itslike mthe last standing thing.
& sorry i say that but thats typically samsung behaviuor. there allways this kind of threads in the samsung forums of xda... other manufacturer can mostly be restored or atleast you know what make it dead.
Exactly the same problems happening to me.
This is my thread:
http://forum.xda-developers.com/galaxy-s3-mini/help/sgs3-mini-dead-t3085031
Can you try to follow what appears on this link? (I can't by now because my PC is broken)
I think won't do nothing because you won't be able to access to the recovery mode on android, as me, but to try...
http://forum.xda-developers.com/showthread.php?t=1840030
bejunk said:
try to plug in the phone into charger & leave it there like 20 mins or more. battery loads then.
then try access samsung download mode, if you cant the phone is probably useless (brick for ever) because itslike mthe last standing thing.
& sorry i say that but thats typically samsung behaviuor. there allways this kind of threads in the samsung forums of xda... other manufacturer can mostly be restored or atleast you know what make it dead.
Click to expand...
Click to collapse
Hi there,
Thank you for your interest but I have passed this point already. Tried a brand new battery I had laying down in the drawer (which was fully charged with an universal charger) and there is no answer to any attempt of turning it on. Via recovery, download or normal boot.
CrashOverride93 said:
Exactly the same problems happening to me.
This is my thread:
http://forum.xda-developers.com/galaxy-s3-mini/help/sgs3-mini-dead-t3085031
Can you try to follow what appears on this link? (I can't by now because my PC is broken)
I think won't do nothing because you won't be able to access to the recovery mode on android, as me, but to try...
http://forum.xda-developers.com/showthread.php?t=1840030
Click to expand...
Click to collapse
Hello there,
I'm sorry to hear I'm not the only one affected by this bug (lets call it a bug). This shows there is a lack of concern from Samsung on dealing with this issues, and thus we see that old programmed obsolescence.
I will try that later on the weekend, and I come back here with an report.
Cheers
ScrewedImei said:
Hi there,
Thank you for your interest but I have passed this point already. Tried a brand new battery I had laying down in the drawer (which was fully charged with an universal charger) and there is no answer to any attempt of turning it on. Via recovery, download or normal boot.
Hello there,
I'm sorry to hear I'm not the only one affected by this bug (lets call it a bug). This shows there is a lack of concern from Samsung on dealing with this issues, and thus we see that old programmed obsolescence.
I will try that later on the weekend, and I come back here with an report.
Cheers
Click to expand...
Click to collapse
this guide useless for you. how u want flash things with odin if u cant enter download mode at all??
im really sorry for you that this phone is dead. just can give you 1 advice, dont buy samsung in future.
I have been repaired my phone successfully!!!
I just needed to change two capacitors on its motherboard, and that's it.
Here the video where I have found the info and how to do that. It's in Spanish but easy to understand for you I think. But if you need some help, send me a PM.
can you take a picture from the location of the 2 capasitors and the types of it
Hi everyone.
I have some news. It took me a while but I followed CrashOverride93's advice on that video. It actually solved one issue, as I now can turn it on, but now I have a second problem, I'm stuck on a boot loop, with acess to Download mode ONLY. No recovery.
Considering where my issue started, and where I am now, I have tried the following:
- Flashed via Odin stock ROM, kernel;
- flashed Wipe;
- flashed PARAM;
- three button combo.
So far I couldn't get it pass the boot loop. Any thoughts?