Wi-Fi issues?? Very poor reception? - Nook Color General

I put CM7 on it the first night I got it so I can't say for sure if it was this way stock, but my Nook Color barely sees my wifi router an won't connect. My LG G2x phone gets 30-50% signal and my Sony VPC1280 laptop gets full signal (it's got fantastic wifi reception).
Is this typical? Well below average wifi reception?
I may need to get a repeater or something. Moving the main router closer to the area I want to use is not an option.

I'm not sure about the wifi reception in general for the NC but for me it works as well as my laptop which is pretty darn good.

My NC connects just fine to my wifi router at home (can't remember brand/model unfortunately), but the transfer rates are pretty bad (3 down, <1 up). My G2 phone gets very good transfer rates (9 down, 3 up). Not sure how to make it better.

I have the same problem... my NC has trouble picking up a WiFi signal in certain places in my house that my other WiFi devices don't.
My guess is that the WiFi antenna is placed where my hands block while holding it or I just have too much interference in my home.

Related

Wifi signal gone

When on wifi my kaiser seems to loose the signal and picks it up again.
its just going on and off.
No problem with the routersignal all wireless computers work fine.
anyone knows about this problem?
cbgnl said:
When on wifi my kaiser seems to loose the signal and picks it up again.
its just going on and off.
No problem with the routersignal all wireless computers work fine.
anyone knows about this problem?
Click to expand...
Click to collapse
Have you put the slider to best performance rather than best battery?
Yes i did
never had the problem with the tytn and wizard.
I only get that on my TyTN II when I'm far away from the router and the signal strength is low. If you've already set the performance vs battery life slider to give maximum performance as suggested by kareem9nba and it's still behaving as reported, what happens when you're near to the router?
If it's just that your saying the range isn't as good as youve been used to with other devices, I have nothing to compare my TyTN II with as this is my first WiFi capable ppc - but I'm sure other more experienced members here will be able to comment. If you're near to the router where there's no doubt it should be working fine and still getting problems then thats a different matter.
maybe your router needs a restart or maybe its just faulty.
have you tried other devices with same router?
try a wifi sniffer/scanner see what happens (a good example would be PeekPocket)
mospantagruel said:
maybe your router needs a restart or maybe its just faulty.
have you tried other devices with same router?
try a wifi sniffer/scanner see what happens (a good example would be PeekPocket)
Click to expand...
Click to collapse
All other devices doenst have the problem output signal is ok but i ll try peekpocket
Flying Kiwi said:
I have nothing to compare my TyTN II with
Click to expand...
Click to collapse
I do! My Kaiser's performance is on a par with my old HTC Universal, which is to say, they are both terrible at getting a signal. I don't think my Kaiser is faulty as back in the Universal forums, it was often commented how useless the WiFi was in comparison to other machines. I used to have a HP Ipaq 5450 which could get a signal upto approx 20m from my router, my laptop starts struggling at around 50m. The Universal could just about get a signal upto 4m away, the Kaiser is no better.
I realise much of this is due router location and the fact that I was trying to get WiFi in my garage, but in my bedroom with a full signal on the laptop, the HTC devices struggle to get more than 1 bar and if I move 10cm further away from the router the signal goes completely.
I think the WiFi on the Universal and the Kaiser just isn't that powerful. I guess it's Maximum Performance setting is still quite low power in order to save battery life. Wonder if there is a registry tweek to increase the power to the WiFi card, and if doing that would blow the card?!
Steve-C said:
The Universal could just about get a signal upto 4m away, the Kaiser is no better.
I realise much of this is due router location and the fact that I was trying to get WiFi in my garage, but in my bedroom with a full signal on the laptop, the HTC devices struggle to get more than 1 bar and if I move 10cm further away from the router the signal goes completely.
Click to expand...
Click to collapse
I'm using an 11 Mbps Wifi capable router (about 2003 vintage) and even with a wall and a floor between my TyTN II and the router it still works about 15 m away, I've yet to try any further as that'd be outside the house. I was impressed to see it even detected other WiFi sources in the area though. I found that even though the signal quality bar was fluctuating, my web browsing still worked OK. Bumping the slider towards the performance end did make a difference to the signal quality indicator (although it still fluctuated). If your TyTN II is only working up to 4 m from your router then I think there's a fault with either device, you should be getting better than that.
I can connect to my linksys WRT54G when beside the it and 20mt away. Even when beside it the TynII will cycle off (disconnect) and then reconnect again. I thought it was signal strength but I am beginning to think its just a crappy wifi setup on the tyn. I also have my slider on best performance.
Flying Kiwi said:
I'm using an 11 Mbps Wifi capable router (about 2003 vintage)
Click to expand...
Click to collapse
Funny that, so am I! However I bought it because it was cheap and I really didn't know much about WiFi etc several years ago when I bought it. I notice many routers come with external antenna's, mine is all internal so I would think that it's more my router isn't that powerful, combined with the Kaiser having a less powerful WiFi set-up that older models. To be fair, the Ipaq had an external antenna (of sorts, a little lump on top) and my previous laptops didn't have built in WiFi, their external WiFi adaptors also had external antenna's.
Frankly I think that all this internalisation of components is having a negative impact on signal strength and range. To compare I have a GSM car kit with an external antenna that picks up a much better signal than a phone on it's own. Likewise my GPS can be connected to an external antenna and I've noticed when connected it will pick up more satalites, with a stronger lock, than when on it's built in antenna. It also picks up more than the Kaiser (internal antenna) or Universal (external bluetooth GPS with internal antenna) ever do.
Still, it all just about works for my needs, so I'm going to leave well alone!
Juzzman said:
I can connect to my linksys WRT54G when beside the it and 20mt away. Even when beside it the TynII will cycle off (disconnect) and then reconnect again. I thought it was signal strength but I am beginning to think its just a crappy wifi setup on the tyn. I also have my slider on best performance.
Click to expand...
Click to collapse
i have the same problem... i hope that's a firmware problem....
checked
i checked signal and even did hard reset on kaiser.
i still have full signal and goes to zero all the time
no clue here
eipiklein said:
i have the same problem... i hope that's a firmware problem....
Click to expand...
Click to collapse
But does this actually affect your browsing? In the end the signal quality bar can do whatever it wants as long as the data still gets through as far as I'm concerned and for me that’s happening. My hunch is that the reason why the signal quality bar intermittently dips down (even when nearby a router) is associated with power management on the TyTN II (which will still be in place to a certain degree even when the performance vs. battery life slider is fully at the performance end).
Flying Kiwi said:
But does this actually affect your browsing? In the end the signal quality bar can do whatever it wants as long as the data still gets through as far as I'm concerned and for me that’s happening. My hunch is that the reason why the signal quality bar intermittently dips down (even when nearby a router) is associated with power management on the TyTN II (which will still be in place to a certain degree even when the performance vs. battery life slider is fully at the performance end).
Click to expand...
Click to collapse
really i can't connect to my wifi router, while other hardware can (a laptop for example). it loops from "connecting" to "available" with 5 bars. but nevers connect or never shows an error. i tried open, WEP, WPA, WPA2 with no results... its a compatibility problem of TYTN II with some routers....
i hope that upgrading firmware, this problem dissapear....
Hi
My experience isn't that the signal itself is particlarly poor, but that it can be prone to loose connection regularly if its very weak. Atm I'm sitting some 150m from the accesspoint (quite powerfull transmitter), through a couple of concrete walls and its fast, as in almost so fast as the Kaiser can chew. Livestreaming from Youtube is np etc. The signal is no doubt very poor tho, and I have to use max signal/minimum battery on that bar you can adjust.
What drives me nuts is that it DCs me and often force me to key in the network key randomly every 1 to 20mins or so. I don't know if this is due to weak signal (both my laptop and the kaiser have 1 bar) or config of the wlan/kaiser. The PC dont DC, but its deffo a cranky connection. It almost seems like theres some auto-DC feature somewhere.
On other networks I haven't seen this. Generally I find the Kaiser wlan surprisingly powerfull, albeit it often shows a weak signal I've found this to be very relative and far from always descriptive of real life performance.
/Mac
kaiser wifi low signal - wi fi poor reception - wifi disconnecting and reconnecting:
Suffered a lot with my kaiser wifi poor reception. Tested several radio versions and could solve the problem.
Radio version:
1 71 09 01 - too low WIFI reception
1.27.12.11 - disconnecting and turning OFF the WIFI with no automatic reengage of the access point or turning ON the WIFI if coverage is good.
1.65.17.56 is the versione that SOLVED my problem.
This radio was collected from the original HTC shipped rom:
RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.17.56_Ship.exe
In this moment I am running Radio 1.65.17.56 with
ROM jjblaster3 - updated 28014 with good WIFI behaviour.
I need to underline that the reception I have now with the Kaiser, can never reach the sensibility of my Nokia 5530 WIFI or the one I have on my laptop with good antenna embeded in my LCD framem but I am happy now because the WIFI is making sense now.
Best Regards
cbgnl said:
When on wifi my kaiser seems to loose the signal and picks it up again.
its just going on and off.
No problem with the routersignal all wireless computers work fine.
anyone knows about this problem?
Click to expand...
Click to collapse
I'm facing the same problem. WiFi worked fine and one day it was suddenly gone. Tried quite a few radios, including 1.65.17.56 and still no deal.
To elaborate, when WiFi is turned on, the icon never even comes up in the taskbar, and it continues to remain in an off state (when checked in wifi settings) even when it's turned on (in the comm manager).
I'm guessing this could be a hardware problem like a loose contact to the antenna? Anyone heard of such issues?
(On a side note, the phone function never worked either, I always got a "No Service")
I've fixed it! I believe the problem was indeed a loose antenna. I opened up my phone and removed the antenna peice (the plastic plate that also houses the speaker) and pushed up the two pins left of the camera (so that they'll have better contact with the antenna piece. Put everything back and now the WiFi works!
Now if only I can figure out why the cellular doesn't work..

wifi signal

Anyone notice dodgy wifi 802.11 signal? I have dd-wrt firmware on my Linksys router with the transmit power amped up and still while in the same room the reception meter on the n1 shows 2out of 3 bars sometimes. Seem peculiar to me. I've tried different channels, lowering the transmit power on the router also.
I am an old iPhone user and I have noticed the same. My iPhone was always connected fine and then in the house I look at the N1 and it is on 3G.. i have to go back into settings-> wireless & networks -> wi-fi settings and connect to my wifi again....
No I mean it just has a poor signal.I look at the wireless clients from my router configuration and the phone has a low signal
ya. but it is essentially the same problem... mine is just worse..
Compared to my iPhone 2G, my T-Mo N1 seems to show the WiFi on full bars less of the time, but actually have better reception in real life marginal areas. In other words, my experience is that the actual reception is better, but the indicator graphic doesn't show full bars as readily as the iPhone did.

Random Slow WiFi problem

So today I started having a strange issue with my Droid Turbo. The WiFi speeds are absolutely abysmal. Everything was fine in the morning. Then I went out for a while and got home around 4, and my phone wouldn't connect to the WiFi. I finally got it to connect, but nothing was loading, so I ran a speed test and saw that I was getting < 1Mbps down and up. This was really strange because I usually get 50 up and 25 down. All my other devices work, including 3 laptops, 2 iPhones, a note 2, an iPad, and a Chromecast. My router is an ASUS Google OnHub, and I used my Turbo to set it up. LTE works fine. I've already tried the basic steps, including a cache partition clear, but nothing is working. Any idea what's going on?
Edit: so I did some testing and found out that if I hold my phone right up to the router it will give me the full speed. Once i move a few feet away it drops significantly. However, my phone still reports the signal strength as "excellent". I also tried this with a different network somewhere else, this time with a Cisco router, and the results were the same.
My wife's phone had all sorts of issues recently with Wifi on her Turbo. Longer story short, we found it was related to interference with her bluetooth (also on 2.4GHz) and possibly interference from neighbors. I'm not sure what changed, but I had her on 2.4GHz and she had all sorts of issues. I moved her to 5GHz which has resolved the issues (though it's much shorter range now, too). Turning off bluetooth seemed to help... but it didn't resolve it completely. The phone would say it was connected, but it wouldn't actually function online. We do live in an apartment complex with LOTS of 2.4GHz users and interference, so something in someone else's apartment may be interfering... obviously I'm not going to be able to figure that out with so many neighbors! Also, we have an Asus router... so that's why I figured maybe something is up with Asus's code or something, too... making more sensitive to interference?
Update: So I noticed that my phone was only connecting to the 2.4 GHz band, which is strange because everything else would connect to the 5GHz band. I messed around a bit and I found out that the range was just too short. When I placed my phone on top of my router, it would connect to the 5GHz band. As soon as I walked away, it would disconnect. So this leads me to believe that the wifi antenna inside my phone got messed up somehow.

WiFi strength, range, and throughput

Rate this thread to express how you think the LG V20's Wifi performs. A higher rating indicates that it has excellent range, throughput, and signal strength. Like when you're taking a dump in the bedroom upstairs, do your videos have to buffer or do they come through without interruption?
Then, drop a comment if you have anything to add!
WIFI Multi Route Network Problem
I am having problems with wifi on my work network in the office. The explanation I got from our IT department is that the phone is having troubles with multi route setting on the network. Wifi home works without problems, but wifi at the office is not working at all. It is showing as connected but you cannot open any page nor get any internet access through any app. Anybody having this issue?
This is the first phone I've owned that has been able to fully utilize my home internet speeds. Every other phone has reduced the speeds by as much as half, and sometimes as little at 25%.
The auto switch between wifi and mobile data works great. There was nothing more frustrating than sitting in my car in front of my house, trying to pull up navigation and the phone running horrendously slow because it wanted to use my wifi that was 100 feet and 16 walls away, just because there was a signal.
I had the same issue with my wi-fi and internet signal for a time. Have you tried checking the phone lines in your area? Stactic noise in the lines may affect the stability of the signal. Have an IT expert check and replace the line if necessary to hopefully resolve the issue.
Signal strength is better than my note 7 before I sent not back I ran test checking data strength. I walked outside up the street connected to home wifi note lost connect 7 houses up the street v20 i was near 9th house
GPS accuracy, Lock speed, and reliability is poor for me. Can we vote on that?
My V20 is head and shoulders better than my Note 7 when it comes to networking performance. I had real, serious issues with throughput on the N7. My Note 3 would get ~5MB/sec transfers from my home Linux servers' SMB shares, the N7 would get 800-1000KB on a good day. The V20 is on par with the N3 on SMB, but where it REALLY shines is encrypted transfers via SCP. I can do SCP file copies at 80MB/sec reliably. It's amazing. I'm guessing we have some sort of encryption offload chip in the phone or something.
Does anyone else have this issue where the wifi cuts in and out every 30 minutes or so? I have a Netgear WNDR3400 router and I'm on Nougat 7.0
very lg-v20
lg v20 perfect phone-very speed.
my favorite phone
I agree man. Very speed. Much phone. Wow.
anon389389109 said:
I agree man. Very speed. Much phone. Wow.
Click to expand...
Click to collapse
xDDDDD Made my day
Auto Proxy
OK so I investigated the issue of not having internet through WIFI although connected to network, and the issue is that the phone cannot use auto proxy? My LG G4 did not have this issue. Setting up manual proxy through Drony app solves the issue. Any way to get this working straight out of android? Seems like 7.0 took a step back in usability.
I have a Asus AC68U router and the LG V20 reports the connection speed as 78Mbps, whereas my S7 Edge shows the speed as 173Mbps while connected to the same network.
Why is the V20 connecting at such a slow speed? Have reset the router, turned off Wifi optimisation on the phone, but speeds have not improved.
Is there anything else I can try out?
krumbs said:
I have a Asus AC68U router and the LG V20 reports the connection speed as 78Mbps, whereas my S7 Edge shows the speed as 173Mbps while connected to the same network.
Why is the V20 connecting at such a slow speed? Have reset the router, turned off Wifi optimisation on the phone, but speeds have not improved.
Is there anything else I can try out?
Click to expand...
Click to collapse
I have the same router. Mske sure you are connected to 5ghz and you will get adequate speed. I have no problems.
Wifi strength is good, a lot better than my G3. The download speeds are a little less than my laptop, like 35 vs 50 and 70 on 2 laptops, they may be connecting to different severs though, the speed seems to vary more on the phone. Sometimes it's slow to switch over to LTE when moving out of wifi range. Tells me no internet connection when wifi is too weak to get a good signal. Mainly an issue I think with a weak wifi signal that it's still trying to connect to.
HBRSR said:
OK so I investigated the issue of not having internet through WIFI although connected to network, and the issue is that the phone cannot use auto proxy? My LG G4 did not have this issue. Setting up manual proxy through Drony app solves the issue. Any way to get this working straight out of android? Seems like 7.0 took a step back in usability.
Click to expand...
Click to collapse
What steps do you go through to make your v20 connect to work wifi? I have a new v20 from Tmobile and upon my 1st try to connect to work wifi, i can reach the splash login page, but after entering credentials, it bounces me back to the splash page instead of verifying that I have logged in. My older Nexus 6 has no issues connecting to wifi...
st0rmz said:
What steps do you go through to make your v20 connect to work wifi? I have a new v20 from Tmobile and upon my 1st try to connect to work wifi, i can reach the splash login page, but after entering credentials, it bounces me back to the splash page instead of verifying that I have logged in. My older Nexus 6 has no issues connecting to wifi...
Click to expand...
Click to collapse
Solution to my issue: Not sure if it was a combination of things or just solely this tip from an LG rep:
Go to: Settings>Apps> (3 dots top left) > Show System> Wi-Fi > (storage>clear cache & clear data)
Tried connecting to Wifi after that and it worked on my v20. Also I entered in slightly different info in my work wifi splash page which may or may not have made a difference.
Hello, has anyone had a problem that they cannot connect to 5G on your router? My phone will not connect to 5G what ever I do, but will connect no problem to 2.4G. I've tested it with several different routers and all my other devices connect without any problems.
WiFi Issues
I was having issues with my WiFi at home only. Connected everywhere else. I found a post on this site that helped. The post was for a different issue. I just looked at all of the other settings that were available and did a little experimenting. My issue is fixed. WiFi is now good everywhere!!! I have T-Mobile so I am not sure if it will work with other carriers.
Dial-er code that got me to the right menu.
*#546368#*918#
I found that taking the metal back off my v20 improved download speed significantly!
I reported that in the discussion about people unable to get 5 GHz Wi-Fi.

Home Network Expert/Engineer Help Needed

Here is how I have my home network setup:
Uverse Gateway (Wifi 2.4GHz SSID=2wireXXX, currently off) (NAT/router 192.168.1.X)(6Mbps data plan)(other Uverse TV boxes are connected via coax)
---Netgear R6250 AC (Gigabit) (as Wifi Access Point 2.4GHz SSID=tesla, 5GHz SSID=tesla5g)
------Gigabit Switch (to TV/BluRay/laptop/etc)
~~~~Wifi Devices (lots of android phones/tablets/roku/etc)
---Netgear Arlo Hub (dedicated wifi to 4 cameras)(seems these like to force themselves to same channel as router, makes no sense?)
---SmartThings Hub (Zwave 900MHz)
---AT&T MicroCell (currently off)
I am getting some dropouts in Wifi lately and looking for some help to see if I have everything configured/connected in most efficient way. 2 kids are usually on tablets playing Minecraft/NBAlive/watching Youtube cooking videos Son has been complaining about wifi a lot lately. I don't think it has been too bad, but I also notice spinning icon on ipad title bar near Wifi occasionally. I've been doing speed tests via google, when everything is quiet I get 6-8Mbps. One kid on youtube drops it ~2Gbps. Occasionally when I get that spinning icon, speed test only gets 0.5Mbps for unknown reason. Recently when this happened I jumped on cat5 connected computer and immediately got 7Mbps.... uverse seems okay.
Home is 2 story, wood, with full basement. All of this (except the switch and wifi devices) is in one cabinet at North end of my house, near main living area. Kitchen, Bedroom are on south end of house (which is about 55feet) so get poor coverage there (phone charging area and bedroom Roku have por signal). Obviously moving it all to the middle of house would cover everything better, but don't have a good spot to place everything at middle of main floor. I have a basement with drop ceiling that I could relocate some stuff too but need to pull cat5 and power there, just under first floor decking.
I had the kids tablets and older devices on 2.4GHz and only a few newer/faster/work devices on 5GHz. Moved my son to 5GHz recently, too soon to tell if it helps his issues.
-Do I have too many devices in one cabinet (as far as number of radio transceivers)? Heat doesn't seem to be problem, not sealed and doesn't feel too hot.
-Would it help to move R2650 to middle of house and turn back on the Uverse wifi? Put kids on 2.4GHz. To minimize re-wiring, I'd probably change the devices to this order: Uverse---GigabitSwitch---NetgearR6250; I think this maintains Gigabit speed inside house.
-I also have another even older Netgear 2.4GHz B(or G?) router, should I put this at other end of house all on same SSID? So I could have three 2.4GHz access points which all appear to be same network (?????). Then just have 5GHz for the important devices (my wife and I).
-What are some ways to monitor/debug this??? I'd like an app to see which devices are using most data throughput at any given moment and total per day. Tried Netgear Genie App but it is pretty limited. Is the only way to use router with custom firmware?
Thanks in advance for any advice or pointers to help!!!

Categories

Resources