Trying to flash back to stock. Bricked. - Galaxy Tab Q&A, Help & Troubleshooting

I have the WOOT sprint G tab.
I am trying to flash back to stock EA24. however i think i bricked my phone.
now i am getting a "phone triangle computer" picture on the phone and it wont do anything.. from there i have been trying to flash with odin
i installed that sprint drivers, opened odin, select the 512 pit file, select the correct binary under the "pda" option, select re-partition. but every time it gets only to this stage and fails, it also failed like this when i was in download mode.
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> Enter CS for MD5..
<ID:0/005> Check MD5.. Do not unplug the cable..
<ID:0/005> Please wait..
<ID:0/005> Checking MD5 finished Sucessfully..
<ID:0/005> Leave CS..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> zImage
<ID:0/005> recovery.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
when it gets to this part there is part of a a small progress bar on my screen.
i then have to shut the phone off and turn it back on for odin to work at all.
kinda scared i screwed my self here.

Turn off the phone by disconnecting the USB cable, holding the power button down until the screen goes off.
Open Odin and select the tar file in the PDA slot only.(You should have remove the MD5 extension already). Do not select re partition, leave everything as it is.
Connect the USB and the device should turn on to the same PC connection to phone error screen. Wait till Odin detects the com Port and flash. Repeat until successful.

I have done this 10 times now exactly like you said, and i still get the same error.
odin 1.7 or 1.3 only selected the file SPH-P100.EA24.SECURE.REV07-FULL_CL871413.tar
everytime it shows part of a blue progress bar and odin says
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> zImage
<ID:0/005> recovery.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

I can get into recovery by using heimdall and a zimage
but from there i get a
checking /system..
E:failed to mount /system (invalid argument)
/system may be rfs. Checking...
checking /data...
checking /datadata...
E:failed to mount /datadata (invalid argument)
/datadata may be rfs. checking...
checking /cache
done!
and then e: Can't mount /sdcard
when i try to choose zip from sdcard.

Phone - triangle - computer is another download. You get that screen when you have a bad flash. Redownload your files - sometimes there is a corrupted file, causing success, but the tab won't boot, so you get the phone - triangle - computer.

I see from your computer output you are missing the dbdata.rfs file. That would explain the blank line.

Related

Help internal mmc block !! galaxytab P1000

recently my galaxy tab keep crashing till it suck in the startup in a flashing logo of samsung
i tried odin never works then i went to samsung maintenance they say u hav to change the motherboard !!
i really dont think the problem from the board i really hope it can be fixed by using some kind of software
here is the text that i got from the recovery mode
--verfing internal mmc block
E: failed to mount mmc : open file
internal mmc checksum verify failed.
#MANUAL MODE#
--updating application ...
E: failed to mount /preload (no such file or directory)
E: install_application_for_customer:cant mount / preload
your storgare not prepare yet , please use UI menu for for format and reboot actions .
--Appling multi-csc...
installing multi -csc
multicsc : scan access to ojxcom .
multicsc : opera mini[lib] reset .
appliedthe CSC-code 'xss'.
successfully applied multi-csc .
Click to expand...
Click to collapse
I think the problem should be solved if you restock to stable gingerbread.. .
Sent from my GT-P1000 using xda app-developers app
tnx for the reply
i tried gingerbread it never works :/ kies cant open the tab my rom was froyo 2.2
He meant you should flash GB using Odin, not upgrade via Kies.
Follow my signature, download Overcome's PDF guide, and GB-Stock-Safe-v5 (it has all the tools you need in it).
Open the guide, jump to page 7, put tab to download mode, and flash according to that guide.
so no need to kies. cuz when it happen i tried other tut required kies i couldn't pass the first stage in oden then it bricked
i'll try it hope it will work tnx guys
sorry guys same result
it failed in the end of first stage
i got this message in odin
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> cache.rfs
<ID:0/004> dbdata.rfs
<ID:0/004> factoryfs.rfs
<ID:0/004> movinand.mst
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Looks like a bad internal sd chip.
Follow ChrisCTX's guide...search for it
Sent from my GT-P1000 using xda app-developers app

Flashing ROM is failed

Hi,
I have Samsung Galaxy S3 I9305 LTE phone made in Vietnam. Initially I got the Samsung Logo stuck issue. In the stock recovery mode i got the following error.
"E:failed to mount /efs (Invalid argument)".
I tried to wipe cache partition and checked. but no luck.
Then I rooted the phone using the following file:
CF-Auto-Root-m3-m3zh-gti9305.tar.zip
Then i installed the CWM recovery using the following file:
CWM_touch_6.0.4.7_i9305.tar
Then I went to CWM recovery and did the following things:
back up to /SD card
wipe data/factory reset
format /system
format /data
wipe dalvik cache
then First I tried to flash the 2 ROMs(I9305XXUFNL1_I9305H3GFNL1_I9305XXUFOA1_HOME.tar.md5 and I9305XXUFNL1_I9305ORLFOB1_I9305XXUFOA1_HOME.tar.md5) . Both are installed. but logo issue was still there. Then I found the ROM(I9305XXUENH1_I9305FTMENJ1_I9305XXUENG1_HOME.tar.md5) using KIES using model no and serial no.
I flashed that ROM using ODIN and ROM installation is failed. Following is the ODIN Log.
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> boot.img
<ID:0/007> NAND Write Start!!
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> modem.bin
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> tz.img
<ID:0/007> sboot.bin
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed.
Then I went to Android Recovery Mode and still I'm getting the following error:
"E:failed to mount /efs (Invalid argument)".
Note: I did not do any mount in recovery mode
Please help me on this.

Help with extracting AT&T S5 G900A Stock Rom and change Language

hi guys i need your help
my phone S5 G900A AT&T Rom 5.1.1 With no root and can't downgrade or add custom recovery
i need unpack to change my phone language and delete AT&T Programs in lollipop ROM 5.1.1 stock ROM
I made the next steps.. if could clarify the wrongs in those steps .. thank you very much
i am using ubuntu 16.04 LTS
first : i have stock ROM with 4 files AP - BL - CP - CSC
G900AUCU4COI5_CL5869384_QB6398515_REV00_user_low_s hip_MULTI_CERT
i need to extract AP_G900AUCU4COI5_CL5869384_QB6398515_REV00_user_lo w_ship_MULTI_CERT.tar.md5
and edit system.img.ext4
by right click on file system.img.ext4 and open with ARK and extract it
now i have those files boot.img - persist.img.ext4 - recovery.img - system.img.ext4
I've downloaded "img-tools" to change ext4 to img
i take a system.img.ext4 file and but it in img-tools folder in my home and do this commands
right click and chose Open in Terminal in img-tools folder
sudo su
enter password
simg2img system.img.ext4 system.img
makdir system
mount -t ext4 -o loop system.img system/
Click to expand...
Click to collapse
now i have mounted system.. i well open it with this command
sudo nautilus
enter password
Click to expand...
Click to collapse
and delete APK files >
Code:
system/APP/*.APK
system/framework/framework-res.apk
system/framework/twframework-res.apk from the same ROM
and replace it with the same files from other ROM S5 G900H lollipop 5.1.1 with national language
when finished i need to repack files with this command
tune2fs -l system.img | grep "Block size"
Block size: 4096
tune2fs -l system.img | grep "Block count"
Block count: 656384
ech $((4096 * 656384))
2688548864
make_ext4fs -s -l 2688548864 -a system system.img.ext4 system
Click to expand...
Click to collapse
now i have my edited sysytem.img.ext4
i need to but it back in the same folder with the next files to repack it in "tar.md5" file to flash it
Code:
boot.img
persist.img.ext4
recovery.img
this commands well do it
tar -H ustar -c boot.img persist.img.ext4 recovery.img system.img.ext4 > my_final_packeg.tar
md5sum -t my_final_packeg.tar >> my_final_packeg.tar
mv my_final_packeg.tar my_final_packeg.tar.md5
Click to expand...
Click to collapse
finally i have the last file to flash it ((my_final_packeg.tar.md5))
the problem is when i flash it by odin3 v3.11 i have this massage
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> persist.img.ext4
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> FAIL (auth)!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
i need your help and Sorry about my bad language

Softbricked my old Galay GT P1000 - can anyone help.

Heyas. I'm hoping someone can point me in the right direction. I'm trying to refresh an old Galaxy Tab (GT-P1000) for my son. Not the first time I've done this but the first time I've hit a deadlock.
I've reviewed the [Guide]How to unbrick your galaxy tab. Not helping unfortunately.
Background:
I've installed TWRP (CF-Root-TAB7_XX_OXA_JQ1-v3.3-CWM3RFS.tar) on the device using ODIN. Installed OK. Booted into the OS fine afterwards.
I copied the firmware (cm-13.0-20160519-UNOFFICIAL-p1.zip) and GAPPS from the microsd card to the /download folder as I've had issues seeing the card from the recovery app.
Booted into recovery - did a system, data and dalvik cache wipe. Installed the CM13 image and rebooted. The message I got was:
failed to mount '/system' (invalid argument)
failed to mount '/data' (no such device)
In an attempt to fix the mount issues I reflashed including a PIT. Now nothing is mounting - I'm guessing I've blown away the partitions.
I can get to the Clockwork recovery application but I can't flash from the SD card as it needs a file system to mount to I'm guessing.
Can anyone point me in the right direction to begin troubleshooting this?
If I try to reflash using ODIN, a PIT file and GB_Stock_Safe_v5.tar
ODIN zips through till it gets to:
<ID:0/004> factoryfs.rfs
At which point it seems to hang up.
eventually ODIN times out with a Fail message. If I reboot I get the soft brick logo of the mobile and PC with the yellow triangle. From this point I can reflash Clockwork Recovery Mod (CF-Root-TAB7_XX_OXA_JQ1-v3.3-CWM3RFS.tar) and get to the download screen again if need be.
I just don't seem to be able to get a working OS up.
Message log reads:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> cache.rfs
<ID:0/004> dbdata.rfs
<ID:0/004> factoryfs.rfs
<ID:0/004> Removed!!
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Note 9 SM-N960U Flash Issues

Greetings all,
I'm attempting to flash my SM-N960U from ATT to Verizon. I've tried the Verizon version: SM-N960U VZW, which passes in Odin but the phone fails to mount the data. I get the following message on the phone:
/////
#Reboot Recovery Cause is [[odin]RebootRecoveryAfterOdinDL]#
Support SINGLE-SKU
Block-Based OTA
Supported API: 3
-- Resizing...
E: failed to mount /data (Invalid argument)
can't mount '/data', rc = '-1'(Invalid argument)
:failed the resizing-data
\\\\\
I tried the stock version SM-N960U1 XAA - which fails. From what I've researched online, the SM-N960U version should be able to work on Verizon when flashed successfully.
Odin log:
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 7107 M
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks for any feedback.
Don't think you can because one is GSM and the other is CDMA.
Sent from my SM-N960U using XDA-Developers Legacy app

Categories

Resources