Related
Okay I don't know if this will help anyone, but I figured out how to stop Windows from detecting the phone as two USB drives when the phone goes into Recovery mode, and to make it show up as Android Composite ADB device.
I do NOT have HTC installed, rather, I'm using the USB 3 drivers that come down through the SDK, so I'm not sure how to do this if you are using the HTC Sync drivers intead.
At any rate, start with the phone off and disconnected. Open the Device Manager. Boot with your prefered method into Recovery mode, then connect the phone. It should detect as USB Mass Storage Device under Universal Serial Bus Controllers. Right click on USB Mass Storage Device and click Uninstall and then OK. Once this is done, disconnect the phone (you can leave it running in Recovery).
Open My Computer and navigate to C:\Windows\inf. Copy the files usbstor.inf and usbstor.pnf to your desktop or wherever, it doesn't matter, just make sure you put them somewhere you can get them later. Then delete them from the C:\Windows\inf folder. These are the drivers that Windows automatically uses for USB storage devices.
Ok, now bring Device Manager back to the foreground and plug the phone back in in Recovery. It should show up as Android Phone with an exclamation mark. If Device Wizard pops up cancel out of it. Now right click on the Android Phone and click update driver. Click Browse my computer for driver software. Click Let me pick from a list... Click Android Phone and Next. Click Have Disk. Browse to your SDK folder into the USB Drivers folder and you should see android_winusb.inf, select that then click OK. You should now have a list of three items to select, this part I am not sure if there is a 'right' or a 'wrong' but I go with Android Composite ADB Interface.
Select that or whichever one you think and this is what it will install as. Bingo, now whenever you connect the phone into Recovery or boot into Recovery with it already connect it correctly detects as the Composite ADB Interface or whichever you selected, but does NOT show up as any USB drives.
Unfortunately... I still could not get ADB Shell to connect (I even went out and bought a 2GB PNY card).... so I don't know if this will help any of you but I figure it's one step closer to what we need to happen.
At any rate, to get everything back to normal as far as your computer being able to use USB storage devices just copy those two files back to the inf folder before you connect them and you should be fine.
bast525 said:
Unfortunately... I still could not get ADB Shell to connect (I even went out and bought a 2GB PNY card).... so I don't know if this will help any of you but I figure it's one step closer to what we need to happen.
.
Click to expand...
Click to collapse
Format it LONG Fat32, 1024k allocation, name it TEST, put PB31IMG.zip (downgrade ROM) on it, power on into bootloader holding volume down until you get to volume up to start upgrade, run the downgrade from Bootloader, then immediately reboot with holding the track button switch into Fastboot menu, power to Bootloader, let the card check run, decline upgrade this time, run your loop.bat or loop.sh if you like linux, power the phone into recovery boot, and prepare yourself to be happy--I think that will work. The whole trick is get a card/format that forces recovery into an ADB-available mode.
Or you could try what I've done 7 times and achieved ADB Shell 7 times...
1. Turn the phone off.
2. Start running Loop.bat
3. Unplug USB cable.
4. Turn device on in Fastboot by holding in the optical joystick and power.
5. Plug USB in.
6. Hit power button once to get to HBOOT.
7. Wait two seconds for it to do it's thing.
8. Pull off the back of the phone.
9. Hit Vol - to Recovery then hit power.
10. Immediately after doing this continuously push the sd card in and out (about every .5 - .75 seconds)
11. ?????
12. Profit
@DigitalDementia--
How is what you said relevant in this thread?
bast525 said:
Unfortunately... I still could not get ADB Shell to connect (I even went out and bought a 2GB PNY card).... so I don't know if this will help any of you but I figure it's one step closer to what we need to happen.
Click to expand...
Click to collapse
drtrmiller said:
@DigitalDementia--
How is what you said relevant in this thread?
Click to expand...
Click to collapse
Pretty positive it had everything to do with that section of the first post, he said he still couldn't achieve root I attempted to help him. Why don't you explain to me exactly what it doesn't have to do with this thread?
rynosaur said:
Format it LONG Fat32, 1024k allocation, name it TEST, put PB31IMG.zip (downgrade ROM) on it, power on into bootloader holding volume down until you get to volume up to start upgrade, run the downgrade from Bootloader, then immediately reboot with holding the track button switch into Fastboot menu, power to Bootloader, let the card check run, decline upgrade this time, run your loop.bat or loop.sh if you like linux, power the phone into recovery boot, and prepare yourself to be happy--I think that will work. The whole trick is get a card/format that forces recovery into an ADB-available mode.
Click to expand...
Click to collapse
The real bummer here - and I should have known better, really - is that this wipes your phone.
I suppose it should be obvious, but take it from someone who's pretty new to Android phones and just wiped their entire phone after following your steps: Please add a warning to your original post.
It's late, I'm tired and irritated, but I'm sort of bummed to know I went from hero to zero in trying to enter shell (again) during recovery all in an effort to get proper perm. root. Sort of ****ty to know that I just lost everything.
still no root
I'm sorry, I shouldn't have assumed people knew an IMG flash from bootloader wipes user data. Believe me, that's not the only time you'll wipe if you keep modding
-------------------------------------Sent via the XDA Tapatalk App
USB drives are ok in recovery
When I am in recovery with adb and working correctly it still shows the 2 USB drives so this is normal and ok, what you have done is fool yourself into thinking that your phone is in correct mode but it really is not, this is why it still does not work, sorry.
rynosaur said:
I'm sorry, I shouldn't have assumed people knew an IMG flash from bootloader wipes user data. Believe me, that's not the only time you'll wipe if you keep modding
-------------------------------------Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
Now that I've scorched the earth, I'm hitting this thing hard with every trick I can think of to get the shell in recovery again.
Thankfully, I at least have my app list on appbrain.
After researching around the different forums, I think this maybe my issue. I will have to make this attempt when I get home.
This is what I posted on a different forum. I am not sure if this is a similar experience you were having:
So, for a little a bit I was having issues with finding and modding the usb.inf file. I got that finally resolved... Now as I go to one of the first parts of the procedure, executing the adb shell command. Well at first it said the 2 lines, about the daemon and whatever the second line was. Anyways, the third line did not say "no device found" it went straight to a shell prompt "$" . The instructions made a point in the instructions for it to say " no device found" .
I went ahead with the rest of the instructions. No Luck. And I did both methods. A co-worker of mine told to run adb devices to see if my phone is recognized. I will also make that attempt tonight.
I wanted to know if any of you had some insight. I made sure I was in the right directory.
I will make another attempt on a different machine tonight.
Thanks. Oh yeah, I do have some UNIX experience if that makes a difference.
I had the same problem, used this method here
addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/
Click to expand...
Click to collapse
Seemed to help me with the dumb usb mass storage devices whilst in recovery
I don't know how I missed this thread earlier though, It had been a problem for me for days!
kentoe said:
I had the same problem, used this method here
Seemed to help me with the dumb usb mass storage devices whilst in recovery
I don't know how I missed this thread earlier though, It had been a problem for me for days!
Click to expand...
Click to collapse
I rooted in Windows, rather than linux, simply because I like the look of MejDam's procedure better than the linux script posted here on XDA--and his windows procedure is accompanied by his YouTube video
Long story short: I had ADB Composite Device AND the two storage volumes mounted together, as I got shell, and did the other steps in recovery. NB: they were mounted as Generic Storage Volumes, not writeable partitions. The stock recovery on DI does not allow host to mount either partions, although I'd like to see if
Code:
mount /dev/block/mmcblk0p1
worked for the SDcard on the sdcard, cuz then it would be a cinch to mount sdcard/emnc partition into host OS--windows, linux, Atari 2600, etc Worth a try.
Anyhow, my conclusion: a bad driver setup could be a barrier to catching adb shell, but it is certain not the prevailing problem for most, IMHO.
Was wondering if bast525(the creator of the thread) was ever able to adb shell while in recovery, and if so what did you do thanks.
Heh, I wish.... I've tried just about every method posted on these forums, and five different SD cards from Sandisk, PNY, and Kingston. The only thing I haven't tried is rolling back to the pre OTA update, because I don't want to wipe the phone at this point.
I'm working to enable FM radio functionality, RX and TX on HTC Legend and other devices with TI FM chip.
I need help to get this done ASAP. I'm an experienced embedded Linux dev, but I'm pretty new to smartphones and Android.
A few weeks back I managed to muddle my way through on phone gold card creation, downgrading, rooting, CWMod (2.5 ?) installation, CMMod7 nightly install, S-Off and new Radio flash. Since then I haven't flashed anything and probably forgot half of what I learned.
So now I want to flash the best ROM for the purpose of figuring out the audio routing "secrets" of the HTC FM app. Any suggestions for the best ROM for that purpose ?
Next, I could use some pointers to the best posts or web pages to refer to for flashing the HTC Rom, and then later flashing back to CM7. As easy as possible. Can I do something Nandroid like and save the entire state of the phone to easily get me back to where I started with CM7 ?
Yes, I AM a dev, but very much appreciate easy to follow step by steps that don't leave me scratching my head wondering if I'll brick my device or create some other catastrophy . Eg: Should I ignore those error messages or not worry ? Do I have to reboot 5 times while clicking my heels ? Etc.
Once I get the above figured out, perhaps this thread can be used for discussion of the observations and any reverse engineering results.
Thanks !
Well, the best ROM would probably be BlaY0's, as it has the FM functionality. Take a nandroid of that and then install CM (as that's what your developing for, ye?). Then nandroid the CM and you can easily switch between the 2 without the need to set it up again.
BlaY0's ROM is based of the official HTC one, so it would probably do for the reverse engineering stuff. Thus I don't think you'd need to go back to a stock HTC ROM. If you do you can just flash a pre-rooted one (found here) and that would do it.
TheGrammarFreak said:
Well, the best ROM would probably be BlaY0's, as it has the FM functionality. Take a nandroid of that and then install CM (as that's what your developing for, ye?). Then nandroid the CM and you can easily switch between the 2 without the need to set it up again.
BlaY0's ROM is based of the official HTC one, so it would probably do for the reverse engineering stuff. Thus I don't think you'd need to go back to a stock HTC ROM. If you do you can just flash a pre-rooted one (found here) and that would do it.
Click to expand...
Click to collapse
OK, thanks GrammarFreak. BlaY0's ROM 0.7 it is.
Hate to be/seem so newb-ish....
So I'm running CM7 now. So:
(1) Run ROM Manager Backup.
(2) Watch phone go into recovery mode with red triangle and exclamation mark.
(3) Don't freak as the backup will take maybe 10-20 minutes or so.
(4) Phone reboots back to CM7 I presume.
(5) Pull any important data from sdcard including ROM backup files.
(6) Download http://blay0.r3volutionary.net/b-0.7.zip
(7) Run ROM Manager to flash Blayo.
(8) Reboot and mess around with Blayo ROM.
(9) When done messing, optionally save Blayo ROM and mods with ROM Manager Backup.
(10) Use ROM Manager restore to return to CM7 ROM.
Sound good ? I don't even have to remember which key when booting brings up CWMod recovery mode ?
I couldn't find a canonical web page documenting CWMod/ROM Manager and it's usage.
Gee my phone has been stuck in red mode for a while now...
EDIT: So I'm reading threads and getting the impression the red triangle is not what I want. So I run "adb reboot" and will check and see if the backup looks good.
I can understand that the "community" has to somehow pull together to pool info, but my experience seems typical of what so many face.
In order to figure out some sort of semi-foolproof method of doing XYZ it seems I have to search threads all over to collect the full info. 50-100+ page threads are a challenge. Do I start with the first few posts or pages of posts, or should I skip to somewhere near the end for latest info ? Yes I can read to see if first posts are updated etc.
Before I started the rooting process on my phone, I read QUITE a few big threads from begin to end. And I made LOTS of notes to try and figure it all out and avoid problems. And my head got so full it almost exploded, and I almost sorta gave up, dived in, did a few more google searches on the way and thankfully finally ended up with a nicely open device.
But it all seems so ridiculously difficult, UNLESS you happen to come across some very succinct, accurate and informative HOWTO somewhere that works well for you.
/rant off
Ok, I want you to do a couple of things:
Forget about ROM manager, it's a piece or crap and it creates more problems than it solves.
So, you said you performed S-OFF, correct? Did you let the S-OFF procedure install ClockworkMOD recovery? Given the red triangle of doom I doubt it. No worries. Here's what you do:
Download this (it's the ADB tools) to a known location. Then extract the zip to a known location. Open a command window in that location (for the sake of this guide: C:\ADB) So open CMD (start, run, type CMD, hit enter) In CMD type "cd C:\ADB". Plug your phone into the computer (make sure you're using CM). Debugging mode should be on (you'll get a notification in the status bar of your phone). Now, I want you to download this (CWM 2.5) and save it to C:\ADB. In CMD type "adb push recovery.img /sdcard" Wait for it to complete. It will output a file-size, time taken and resultant transfer rate. When it's completed type "adb shell". You'll end up with a "#" and nothing else (if you get a "$" just type "su" and hit enter, and on the phone's screen accept the Superuser request). Now, type "flash_image recovery /sdcard/recovery.img", let it do it's thang. When you see the "#" type "reboot recovery", and your phone will reboot to CWM. This is what I refer to as a win
Now, from clockworkMOD you can use the trackball (move and click) to select "backup/restore" then "backup". Let it do its stuff. Once backed up you can flash B-0.7 and then back that up. Note down the name of each backup so you know which is which
TheGrammarFreak said:
Ok, I want you to do a couple of things:
Forget about ROM manager, it's a piece or crap and it creates more problems than it solves.
So, you said you performed S-OFF, correct? Did you let the S-OFF procedure install ClockworkMOD recovery? Given the red triangle of doom I doubt it. No worries. Here's what you do:
Download this (it's the ADB tools) to a known location. Then extract the zip to a known location. Open a command window in that location (for the sake of this guide: C:\ADB) So open CMD (start, run, type CMD, hit enter) In CMD type "cd C:\ADB". Plug your phone into the computer (make sure you're using CM). Debugging mode should be on (you'll get a notification in the status bar of your phone). Now, I want you to download this (CWM 2.5) and save it to C:\ADB. In CMD type "adb push recovery.img /sdcard" Wait for it to complete. It will output a file-size, time taken and resultant transfer rate. When it's completed type "adb shell". You'll end up with a "#" and nothing else (if you get a "$" just type "su" and hit enter, and on the phone's screen accept the Superuser request). Now, type "flash_image recovery /sdcard/recovery.img", let it do it's thang. When you see the "#" type "reboot recovery", and your phone will reboot to CWM. This is what I refer to as a win
Now, from clockworkMOD you can use the trackball (move and click) to select "backup/restore" then "backup". Let it do its stuff. Once backed up you can flash B-0.7 and then back that up. Note down the name of each backup so you know which is which
Click to expand...
Click to collapse
Thanks for the newb-friendly instructions. Much of I don't need, but may help others.
I'm running Linux, I've had adb etc installed for 2 weeks. I've got the SDK installed w/ Eclipse but never tried it, but have done App Inventor. And I've been poking around in the innards of the various source codes, binaries, firmwares and other files for the last 2 weeks too.
OK, I'll "Forget about ROM manager" and just use CWM after manually rebooting into it with Volume Down or whatever.
I'm pretty positive I'm S-OFF and have CWM 2.5.0.0.7 or so installed. ROM Manager says so. I have CWM on before I S-Offed using the Bell/Virgin modified alpharev boot disk.
I'll do the backup manually with CWM later tonight when I get back to this. I checked the SD and the backup isn't there, although there are still 3 backups I took when I installed CM7 2 weeks ago.
So I guess I do a complete flush or wipe or whatever when installing the new (or a backed up) ROM ? And since the backup is a nandroid type it will absolutely restore to exactly the same state as when the backup was taken ? But the SD card is not touched...
EDIT:
"adb reboot recovery" gives me red triangle of doom.
"adb reboot bootloader" gives me AlphaRev and I see S-Off and HBOOT 1.000000000
Did AlphaRev remove CWM ?
Given that you get the red triangle we can assume you don't have CWM installed to /recovery, you have it in fakeflash. Nothing inherently wrong with that, just FYI
As for your rant in post numero uno, I've often considered trying to put together a comprehensive "document" on the matter, but it'd take an age and would probably raise more questions than it'd answer.
"adb reboot recovery" gives me red triangle of doom.
"adb reboot bootloader" gives me AlphaRev and I see S-Off and HBOOT 1.000000000
Did AlphaRev remove CWM ?
Click to expand...
Click to collapse
See above about fakeflash. You could well use the image I linked above and use flash_image on the phone or fastboot to flash it
Fakeflash is pretty easy, I either do that or do my business in rom manager as I find that easy.
Rom manager method for installing a new rom:
If rom manager isn't installed, do so from the market
start up rom manager
tap "backup current ROM" (I suggest naming your backup, I just use the rom name)
Let it reboot and do it's thing
When it's booted back into CM7, open up rom manager again
tap "install ROM from SD card"
browse your sd for your rom and tap it.
You are presented with 2 check box options
Since we already backed up make sure "backup existing rom" is unchecked
If you are flashing a new rom, make sure "Wipe Data and Cache" is checked
If you are flashing a newer version of the same rom, you can leave this area unchecked as it will not erase the stuff stored on the phones built in memory
Press ok, let it do it's thing and thats it.
Place the fakeflash update.zip from http://forum.xda-developers.com/showthread.php?t=698404 on the root of your sd card
turn off your phone
Hold the volume down button as you press the power button
using the volume buttons, navigate to "recovery"
press power
your phone will reboot to th red triangle (of DOOOM)
Don't panic, hold volume up and press power (if it gives you an error just wait few seconds)
Using the volume buttons to scroll and power for enter choose "apply sdcard:update.zip"
Use the trackball and go to "Nandroid" if you are using ClockWorkMod 2.5.xxx fake flash or "backup and recovery" if you are using ClockWorkMod 3.xxx
hit "backup"
Let it do it's thing
If you're installing a new rom, scroll to "wipe data/factory reset", wait, then choose "wipe cache partition". If your installing a newer version of the same rom, don't bother.
Scroll to "install zip from sdcard"
scroll to "choose zip from sdcard"
choose your zip, let it do it's thing, and thats that.
You're SD is not touched at all during flashing, no need to backup those files.
Wow, can't believe I typed all that out...
TheGrammarFreak said:
As for your rant in post numero uno, I've often considered trying to put together a comprehensive "document" on the matter, but it'd take an age and would probably raise more questions than it'd answer.
See above about fakeflash. You could well use the image I linked above and use flash_image on the phone or fastboot to flash it
Click to expand...
Click to collapse
Re: rant, don't want to come off as complaining, I KNOW documenting semi-foolproof procedures is tons of work, to do properly. I understand a big problem is consideration of the large set of combinations of ROMs, recoveries, apps, S-On/S-Off states, Radios, etc.
OK, cool, I want "realflash" type recovery then. I guess that's one reason to have S-Off ?
I had to slightly alter your first command by appending a '/'.
EDIT: WOOHOO ! Success I think ! Feel free to skip the rest of this post unless you want to hear the details of my adventure...
Thank you ! Editing this post the last hour I wrote "Success ! " here anticipating such, but alas, I have some issue.
I don't know if I have to be extra patient as deodexing happens, Or if I'm stuck in some boot loop... I see "HTC quietly brilliant" and screen flashing on and off and re-writing the HTC spam.
Re: HTC FM app. OK, cool, I see :
ls -l /system/app/HtcFMRadio.apk
-rw-r--r-- root root 826176 2008-08-01 07:00 HtcFMRadio.apk
And bluetooth. Is there any way to switch normal media output, like from TuneIn radio etc, to my cheap new bluetooth headset ? I pushed the button in CM7 and I see I could start a voice dial, but I figured BT would take over all audio I desired routed through it.
-----------------
I did:
adb push recovery.img /sdcard/
adb shell flash_image recovery /sdcard/recovery.img
adb reboot recovery
In the CWM menu I had to select "Nandroid", and then "Backup".
That completed.
I didn't want to bother rebooting, so manually grabbed the backup files:
adb shell ls -l /sdcard/clockworkmod/backup/
adb shell ls -l /sdcard/clockworkmod/backup/2011-02-27.03.19.57/
mkdir cm7backup-2011-02-27.03.19.57
cd cm7backup-2011-02-27.03.19.57
adb pull /sdcard/clockworkmod/backup/2011-02-27.03.19.57/boot.img
adb pull /sdcard/clockworkmod/backup/2011-02-27.03.19.57/cache.img
adb pull /sdcard/clockworkmod/backup/2011-02-27.03.19.57/data.img
adb pull /sdcard/clockworkmod/backup/2011-02-27.03.19.57/nandroid.md5
adb pull /sdcard/clockworkmod/backup/2011-02-27.03.19.57/recovery.img
adb pull /sdcard/clockworkmod/backup/2011-02-27.03.19.57/system.img
Then to be sure:
cat nandroid.md5
md5sum *.img
Yes, looks good ! Now for Blayo:
cd ..
adb push b-0.7.zip /sdcard/
Goto CWM. Version 2.5.0.1, I had a 7 at the end before. Fine I'm sure.
Use volume up/down to select install from a ZIP. Press power to select. Oh, oh, shoulda used the trackball switch as it powered off.
Whoops, press power again and screen comes back, LOL. Choose zip from sdcard and use trackball switch this time. Move and select Blayo b-0.7.zip
Wonderfully wacky confirmation. Error message saying it can't find the zip file. Hmmm....
Reboot a few times and finally do "adb reboot recovery" and retry install from ZIP.
No go, get:
-- Installing: SDCARD:b-0.7.zip
Finding update package...
Opening update package...
E:Can't open sdcard/b-0.7.zip
(bad)
Installation aborted.
Try to open 98 MB zip file. No go. AHA ! corrupted file.
Try download from mirror 2: http://www.dkmdesign.dk/custom_roms/blay0/b-0.7.zip File is supposed to be 126 MB.
Gee I'm glad there's an unzip process that checks the integrity of ROM flashes.
So again:
adb push b-0.7.zip /sdcard/
And install, running..... Done !
Try to use power button to reboot. Use back key and "reboot system now". Cross fingers and offer the gods sacrifices...
See androids on skateboards again. Recall I may have to be patient as deodexing happens... See "HTC quietly brilliant" spam,,, in this context,good. Waiting....
Waiting.... screen flashing on and off and writing the HTC mind control spam.
Try reboot when tired of waiting and same thing. AFAICT, from "adb shell ls * etc" on the filesystem, Blayo ROM is installed but just won't stop flashing the HTC logo.
speedyink said:
If you are flashing a new rom, make sure "Wipe Data and Cache" is checked
Click to expand...
Click to collapse
Thanks. Maybe that's my boot loop or whatever problem now. I didn't recall seeing that option, but should be there with CWMod, so I'll try installing Blayo again after that.
There was some Wipe in main menu, and another w/ factory reset. Also in advanced menu I selected Wipe Dalvik cache. I left the Battery Stats alone. Hmmm. Naah !
Did all 3 wipe twice for good luck. Rebooted in between. Installed. Now waiting... Oh here's the HTC screen again. Time to read the Blayo thread to see how long to wait. etc.
Man what a pain ! Yet likely a world easier than the new paths I attempted to forge on my previous LG Optimus Chic resulting in a hard brick, LOL.
WOOHOO ! Success I think !
Welcome to the BlaY0 universe.. Just remember that many of us went through this journey as well to have our phone in same state Glad you got to fully download the BlaY0 rom from my mirror.. now happy reverse engineering..
Sent from my Legend using XDA App
whitetigerdk said:
Welcome to the BlaY0 universe.. Just remember that many of us went through this journey as well to have our phone in same state Glad you got to fully download the BlaY0 rom from my mirror.. now happy reverse engineering..
Sent from my Legend using XDA App
Click to expand...
Click to collapse
Thanks. Figured I was finished messing with such nasties once I had CM.
(In case you aren't aware, I have scripts that make the FM radio "work" on CM7. I can scan and see RSSI as expected etc. Only "problem" is I haven't figured out the audio routing part yet so no sound, which is why I'm exploring the HTC app for it's special tricks.)
What I want to do now is try running my hcitool scripts and see if they work on Blayo ROM.
If yes, then the Blayo ROM has something the CM7 ROM needs.
If no, then there's likely some magic step required on either stock ROM or CM7 ROM and likely the HTC FM app is doing that step, directly or indirectly.
But the needed hcitool is not on Blayo ROM. I find 3 of the hci utils and install them. Now I can't get hciattach running, which I think is needed for hcitool.
I'm guessing I can edit /init.legend.rc and change service hciattach to enabled. Reboot and no dice. Try running from command line also with no luck. At one point it hung, but now:
# hciattach -n -s 115200 /dev/ttyHS0 texasalt 4000000 flow
Unknown device type or id
# hciattach -n -s 115200 /dev/ttyHS0 any 4000000 flow
Can't set device: Device or resource busy
Can't initialize device: Device or resource busy
# hciattach -n -s 115200 /dev/ttyHS0 any
Can't set device: Device or resource busy
Can't initialize device: Device or resource busy
Waiting with baited breath
Sent from my Legend using XDA App
pjgodd said:
Waiting with baited breath
Sent from my Legend using XDA App
Click to expand...
Click to collapse
Bated ? Baited=fish
Well AFAICT, the world of Bluez bluetooth and hciattach, hcitool, hciconfig and hcidump doesn't get along with the TI BT stack world of btipsd and btipds_cli.
I'll have to bust out the NDK and start trying APIs.
But FIRST, I'm happy to report that btipds_cli is a pretty interesting and cool tool. Once I rebooted, turned BT on and learned the quirky UI, it wasn't too long before I had FM audio coming out of the speakers or the headphone.
I even tried a BT over FM option in another menu, but no go. Next I'll try the FM Tx, cause I'd REALLY like to see if that works.
btipds_cli doesn't seem to want to start FM a second time though, so a few reboots might be needed for testing.
I think it's possible that the "14.start_audiO" option in the "4.fm_Rx/" is the missing link for FM in non HTC ROMs. I don't know yet if it initiates a digital PCM / SCO connection or just switches analog. I don't see any new processes for that but btipsd might be doing the good stuff.
Following this thread with great interest..
Sent from my Legend using XDA App
I still can't get the transmitter to work, despite all the commands seeming successful. Both with hcitool on CM7 and btipsd_ci on Blayo0.7.
So I think one, or both, of the following are the TX issues:
(A) - It is somehow disabled by the hardware. The Tx antenna pin could be tied to ground, perhaps even through a capacitor or something. It may even just be unconnected and unable to transmit a few inches because it's inside an RF shield.
(B) - The firmware file for the FM portion disables TX, yet the registers still respond as if it works.
(A) would be difficult to infeasible to fix.
(B) should be fixable by loading a firmware file from a TI FM chip device that is known to support transmission.
For a TI based device that is known to transmit, I presume firmware files for a TI or TI partner evaluation board may work.
So far I can't get hciattach and hcitool etc working on BlaY0 ROM.
I HAVE, however, gotten btipsd and btipsd_cli to work on CM7. I had to create the /data/btips directory and am running btipsd manually in foreground.
What I find is exactly the same as with my hcitool scripts: everything seems to work but actual sound doesn't exit the device. Even after doing everything else the same as with BlaY0 ROM.
The /etc/firmware files on both ROMs are identical.
So I'm thinking there is some other thing separating the two ROMs. Could be some HTC customized library, or a config file or who knows.
Hi Mike, your work is appreciated, i hope you wil get it to work. We have great legend dev's. Please BlaYo and. Ali Ba, help this guy!
mikereidis said:
I HAVE, however, gotten btipsd and btipsd_cli to work on CM7. I had to create the /data/btips directory and am running btipsd manually in foreground.
Click to expand...
Click to collapse
Then you got as far as I did a few months ago. The btipsd stuff can be found in the original init.legend.rc, if you are interested.
mikereidis said:
So I'm thinking there is some other thing separating the two ROMs. Could be some HTC customized library, or a config file or who knows.
Click to expand...
Click to collapse
"Customized library" applies here, but that's in fact a euphemism for "all kinds of proprietary code in the framework".
I gave up reverse engineering after looking at the disassembled HTC radio application. As I already told you there are loads of pointers to closed source TI code that can be found in the framework (= /system/lib/whatever.so). You will have to reverse engineer all those rpcs, libandroid_servers and god knows whatnot.
ali ba said:
I gave up reverse engineering after looking at the disassembled HTC radio application. As I already told you there are loads of pointers to closed source TI code that can be found in the framework (= /system/lib/whatever.so). You will have to reverse engineer all those rpcs, libandroid_servers and god knows whatnot.
Click to expand...
Click to collapse
Oh, there must be SOME shortcut...
Since I have the FM radio and audio working with the btipsd_cli. I'm not sure the answer would lie in the HTC FM app. Or at least the answer is in btipsd_cli also.
I'd love to find the source to btipsd_cli. I DO have source for TI's fmapp and fmstack-0.12 and I can see they share some, but not all code.
In a log I can see an HCI command is sent when audio starts; I just don't know which one or with which parameters.
btipsd_cli has some rather weird bugs that prevent me from experimenting well with audio routing. When I disable analog, audio keeps playing. At first I thought it was using digital, but now I think it's part of the buginess. When I select various digital options, various weird things happen, including a crash in btipsd for most of them.
If I can run some HCI queries, I might get better clues or the actual answer. I managed to get hciattach to sort of work with "texas" as the type, but I think I need "texasalt" and the binary I have that runs on Blayo doesn't support it. The CM7 binaries wont run on Blayo.
So unless there are some other tools I can use, I'm wondering if it's time to write an NDK app.
Unless I can increase the verbosity of the btipsd logging to tell me everything it's doing. Will check.
These AudioRouting strings aren't in the CM7 libandroid_runtime so I tried pushing the Blayo lib to CM7. GUI never boots fully, but no audio still using the btipsd_cli.
Same when I also replace libandroid_servers.so, bluez-plugin/audio.so and bluez-plugin/input.so
strings blayo/system/lib/libandroid_runtime.so |grep -i audiorouting
FM_RX_DisableAudioRouting
FM_RX_EnableAudioRouting
nativeJFmRx_SetAudioRouting(): Entered
nativeJFmRx_SetAudioRouting: fmapp_set_audio_routing() returned %d
nativeJFmRx_SetAudioRouting(): Exit
nativeJFmRx_disableAudioRouting(): Entered
nativeJFmRx_disableAudioRouting: FM_RX_DisableAudioRouting() returned %d
nativeJFmRx_disableAudioRouting(): Exit
nativeJFmRx_enableAudioRouting(): Entered
nativeJFmRx_enableAudioRouting: FM_RX_EnableAudioRouting() returned %d
nativeJFmRx_enableAudioRouting(): Exit
nativeJFmRx_EnableAudioRouting
nativeJFmRx_DisableAudioRouting
nativeJFmRx_SetAudioRouting
FM_RX_DisableAudioRouting
FM_RX_EnableAudioRouting
DisableAudioRouting
EnableAudioRouting
editi guess sdcard is incorrect/confusing for my situation, it's the entire system up to root folders is stuck in a read-only type state.
I didn't really see anything that fits my current problem (sorry if there is an answer somewhere buried in here)
So to start off with info, I installed Android on the TP back in February for my fiancée just for the basics of email, videoplayer, comic reader, internet browsing. Nothing too extravagant, just something with more to offer than webos.
I never did any updates on it because it worked perfectly fine for what it was being used on.
I've changed out the video selection many times as she watches through the shows with no problems.
Now I go to change the files and I delete them, add the new stuff, all seems fine. Then I unmount it and everything I deleted is back and everything I added is gone. I've uninstalled apps and they come back, I've done updates to apps and they revert back to before the update.
I've gone into CMW and done the wipes and even formatted sdcard, cache, etc. Nothing works. Even mounting USB in CWM to add files gives the same result of them disappearing right after it is unmounted.
I've tried ACMEUnistaller but it doesn't work. I saw something flash by the screen about something failing, but it goes too fast to even really see what it's about.
Sorry this is so long. I appreciate any insight!
Kernel
2.6.35-palm-tenderloin
[email protected]ost #12
CyanogenMod version:
9.0.0-RC0-Touchpad-alpha2
Build Date
Mon, Feb 20 13:59:21 CST 2012
Build Number
IML74K
plasticsoldier said:
I didn't really see anything that fits my current problem (sorry if there is an answer somewhere buried in here)
So to start off with info, I installed Android on the TP back in February for my fiancée just for the basics of email, videoplayer, comic reader, internet browsing. Nothing too extravagant, just something with more to offer than webos.
I never did any updates on it because it worked perfectly fine for what it was being used on.
I've changed out the video selection many times as she watches through the shows with no problems.
Now I go to change the files and I delete them, add the new stuff, all seems fine. Then I unmount it and everything I deleted is back and everything I added is gone. I've uninstalled apps and they come back, I've done updates to apps and they revert back to before the update.
I've gone into CMW and done the wipes and even formatted sdcard, cache, etc. Nothing works. Even mounting USB in CWM to add files gives the same result of them disappearing right after it is unmounted.
I've tried ACMEUnistaller but it doesn't work. I saw something flash by the screen about something failing, but it goes too fast to even really see what it's about.
Sorry this is so long. I appreciate any insight!
Kernel
2.6.35-palm-tenderloin
[email protected] #12
CyanogenMod version:
9.0.0-RC0-Touchpad-alpha2
Build Date
Mon, Feb 20 13:59:21 CST 2012
Build Number
IML74K
Click to expand...
Click to collapse
I've run across this 3 times with TPs I work on....
1st one had to be sent back to HP because somehow internal memory was damaged and got locked in some some of read only mode
2nd one I saw, I went into webOS, installed the internalz app, mounted the TP to the computer, then added and erased some files and from then on all was good in both webOS and Android
3rd and 4th (same customer) had to be sent in to HP
Now let me mention I live in Costa Rica so all these have been exposed to several scans at airport security checkpoints. I mention this because I haven't seen anything close to a read only problem with the TPs in the USA
Sent from my aokp_tenderloin using Tapatalk 2
thank you so much for the info. Unfortunately Internalz didn't want to help the items stay deleted either. The stuck in read-only type mode is very weird.
I'm pretty sure I am 3 weeks out of the 1-year warranty on it, plus I am unable to remove android from it to even trick them that it just doesn't work.
I guess I'll try webos doctor and see if that can get it going.
edit: webos doctor not working, even with the closing it at 8-12% tricks and doing the lvm.static..... stuff... 'cause it of course doesn't see to actually delete anything... i'll have to double check tomorrow when i bought it, pretty sure it's over the year and since it turns on and has android kinda screwed
plasticsoldier said:
thank you so much for the info. Unfortunately Internalz didn't want to help the items stay deleted either. The stuck in read-only type mode is very weird.
I'm pretty sure I am 3 weeks out of the 1-year warranty on it, plus I am unable to remove android from it to even trick them that it just doesn't work.
I guess I'll try webos doctor and see if that can get it going.
edit: webos doctor not working, even with the closing it at 8-12% tricks and doing the lvm.static..... stuff... 'cause it of course doesn't see to actually delete anything... i'll have to double check tomorrow when i bought it, pretty sure it's over the year and since it turns on and has android kinda screwed
Click to expand...
Click to collapse
I would suggest trying to restore down to WebOS 3.0. In that procedure you literally wipe EVERYTHING on the internal partitions in novaterm and start from absolute scratch. Therefore, if it a software issue you could solve the problem. However, if it is a hardware issue, you'd be kinda screwed.
Yeah, none of the methods I've ended up finding about this problem or other bricked problems are working at all.
i checked at work when i bought it, which of course the 11th was the year mark... but I do have android installed so even if i can get any chance of them honouring it so close they'll probably be like "oh you have android, that'll be $$$ for us to do anything. thanks!"
So I guess I now I have a paperweight with some features.
cdzo72 said:
I've run across this 3 times with TPs I work on....
1st one had to be sent back to HP because somehow internal memory was damaged and got locked in some some of read only mode
2nd one I saw, I went into webOS, installed the internalz app, mounted the TP to the computer, then added and erased some files and from then on all was good in both webOS and Android
3rd and 4th (same customer) had to be sent in to HP
Now let me mention I live in Costa Rica so all these have been exposed to several scans at airport security checkpoints. I mention this because I haven't seen anything close to a read only problem with the TPs in the USA
Sent from my aokp_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
When you got the tablets back had they been fixed or were they refurbs ? Did HP say anything about Android still being on it?
There is a thread in the General forum about how to restore and downgrade. Have you tried that thread ? It is usually a great way to try and get that last restore before sending it back to HP.
73 de VE6AY
Sent from my HP Touchpad, running the latest CM9 nightly, from the XDA Premium App
how are you adding and deleting files when in android? which version of android do you have installed? have you tried different rom versions? have you tried moving and/or deleting files over adb? are you using windows or linux on your computer that youre connecting the touchpad to? it doesnt make sense that the sdcard would be set to read only. is it only certain folders that you cant modify the contents of, or is it the entire sdcard? are you able to modify contents of folders in the / directory of the device using root file explorer or es file explorer in android? have you run "fix permissions"? Also, running webosdoctor wont wipe the sdcard contents or format the sdcard in any way. its going to change the data in the webos partition and may change some data in the /boot directory.
sstar said:
When you got the tablets back had they been fixed or were they refurbs ? Did HP say anything about Android still being on it?
Click to expand...
Click to collapse
They had been fixed but the owners sent them off and had to pay for the whole thing because they had Android on them. When I got my hands on them again I just reinstalled Android. HP charged a little over a hundred dollars for the fix
Sent from my aokp_tenderloin using Tapatalk 2
cdzo72 said:
They had been fixed but the owners sent them off and had to pay for the whole thing because they had Android on them. When I got my hands on them again I just reinstalled Android. HP charged a little over a hundred dollars for the fix
Sent from my aokp_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
Thanks for the answer, this would tend to suggest that the problem is software based corrupted or otherwise. I am trying to find a program that will allow me to read/format the Android partition on my windows computer and will let you know if come up with anything.
Regards
i guess i should change the title slightly.. it's not sdcard, but basically the entire touchpad contents. go to root and delete whatever i want and it doesn't matter. connect it and format with windows and it doesn't actually matter.
haxin said:
how are you adding and deleting files when in android?
Click to expand...
Click to collapse
i've added and deleted just by using mtp. i've also deleted the files on the android side with the video player (vplayer) i've installed es file explorer (which after restart is gone) and deleted with that. i've also gone into webos and installed internalz pro and deleted files that way, which it then seems to work until i of course do anything related to restarting.
some of the files i've put on, i've had it recognize briefly. so for the video file, start it, then it gets really choppy/glitchy playing it. so stop it, go back into the vplayer and it's back to the old stuff
which version of android do you have installed? have you tried different rom versions?
Click to expand...
Click to collapse
android version 4.0.3. nothing else will install. if i add files while in android, when i boot into cwm they are gone. if i mount usb in cwm and add them they stay briefly but when i try to flash them they fail.
have you tried moving and/or deleting files over adb? are you using windows or linux on your computer that youre connecting the touchpad to?
Click to expand...
Click to collapse
i have not tried adb yet, just not as familiar using it properly, i will give it a try though.
i am using windows 7 on my laptop currently. i do have a pc upstairs that i barely use that has vista, but i don't know how that would make a difference to the touchpad
it doesnt make sense that the sdcard would be set to read only. is it only certain folders that you cant modify the contents of, or is it the entire sdcard?
Click to expand...
Click to collapse
yeah as i put above i guess saying sdcard was a bit confusing/misleading (my bad, sorry!), i didn't really know what else to call it at the time or how to explain myself properly at first.
are you able to modify contents of folders in the / directory of the device using root file explorer or es file explorer in android?
Click to expand...
Click to collapse
i can move/delete/modify anything which has absolutely no effect to the device. i've used es file explorer and gone up to root and deleted everything and the system runs fine. says the system is empty with lots of free space (its the 32gb model) but restart or even go into recovery and everything is once again there.
have you run "fix permissions"?
Click to expand...
Click to collapse
i've run it a few times. just acts likes it's working and then says done. i've even gone into the mounts and storage in cwm and formatted sdcard/cache/data/system. does nothing at all in the end of things
Also, running webosdoctor wont wipe the sdcard contents or format the sdcard in any way. its going to change the data in the webos partition and may change some data in the /boot directory.
Click to expand...
Click to collapse
it was just something to try to get somewhere right. it never gets past 12%. always fails to reboot.
I am currently letting the battery drain and see if it dying and then being charged will do anything. probably not. but who knows. i talked to a "tech" on the chat support (i never mentioned android) who told me that having preware installed in webos causing it to become corrupt and they "don't knowledge of preware installed devices" exact words. no idea what that means haha don't have knowledge, don't acknowledge...
anyhow. i've not quite given up. i just don't really see it turning out any differently from the previous times. i do appreciate all the feedback and help very much though
ok so heres what I would try. First try flashing a new fresh rom. download one that you want to your computer like cm9 nightly or aokp or whatever you feel like. then boot into CWM recovery connect the touchpad to the computer via usb. then connect to the touchpad with adb. I'm not sure how to do this in windows because it's been so long since I've done it on a windows box, I always use linux.
adb has alot of options, you can move files to and from the device, you can uninstall or install app packages, and more. this way you can adb push the rom .zip to the touchpad's sdcard while youre in cwm recovery. this way you dont have to reboot the touchpad and risk having the file disappear, you can just go to 'install zip from sdcard' and then 'choose zip from sdcard' in cwm recovery after you adb push the rom, you should see it in the folder you pushed it to on the sdcard.
If you arent familiar with how to use adb from the command line or the terminal this might not make alot of sense and i dont know how better to explain it than that. Also yes windows 7 vs windows vista does make a difference there are issues with novacom installing properly, that's why you would have problems running acmeuninstaller or acmeinstaller2. if you look around you should find some videos or how to's that can probably explain it better. Hope this helps.
http://www.webos-internals.org/wiki/Novacom_with_Windows_7
http://forums.webosnation.com/webos-internals/295881-webos-doctor-12-issue-fixed-5.html
http://forum.xda-developers.com/showthread.php?t=1426244 is the thread I was talking about - it allows you to access the hard root of the device, repartition it, and start again from scratch. It is what I was suggesting last night, from my tablet when I didn't have the link handy.
ve6ay said:
http://forum.xda-developers.com/showthread.php?t=1426244 is the thread I was talking about - it allows you to access the hard root of the device, repartition it, and start again from scratch. It is what I was suggesting last night, from my tablet when I didn't have the link handy.
Click to expand...
Click to collapse
Probably the best suggestion yet given that everything else has been tried.
Good luck.
****EDIT****
Before you attempt the step above I have just noticed a difference between between cwm and. TWRP2.2 which I have installed on my Touchpad via goo manager. If I open recovery via goo manager and then select wipe it gives me 4 options cache, davlik, factory reset AND system which i think says will remove your rom . I don't see the forth option available with the regular cwm/clockwork. Just a thought.
All the best with whatever you try next.
sstar said:
Probably the best suggestion yet given that everything else has been tried.
Good luck.
Click to expand...
Click to collapse
this would work, however you have to fix you novacom/novaterm issues on your windows machine before you'll be able to do any of this. the reason acmeuninstaller, acmeinstaller2 arent working is likely because youre on a windows7 64bit box and Palm-sdk, the novacomd.exe, noverm.exe, and javaruntime apps and drivers arent setup right. just make sure you have the proper javaupdates on your computer then you can install preware in webos, preware has some nice tools that will delete the entire android install partitions, one is called 'remove android' and the other is called 'tailor' you run them from within webos. after you do that then in webos you should do a full device reset. you'll find it in the "info" tab under settings in webos. this will delete and reformat the whole /media ,(aka sdcard) partition. so you will lose all the files you have stored on both webos and android. that format will take a long time probably like 30 min or more. after thats done. reboot the hp and run webosdoctor. now i know for sure this will work because ive done it on mine. remember to put the touchpad in developer mode in webos first to install preware. you can do that by typing webos20090606 into the webos search bar and hitting enter. I'll put links from my box.com accou t to everything you need.
https://www.box.com/s/479acdb6ef9c99fc7b92
https://www.box.com/s/1aed4722990aad251570
edit: also I'm not sure if youre on the 16gig 32gig or 64gig pad, the webosdoctor that i linked is for 32gig wifi only US version. if thats not what you have then youll need to get the doctor for for specific touchpad. or you could create a webosmetadoctor but thats a whole nother project.
i have the 32gb version. i assume US and Canadian aren't gonna make a difference
i've tried all those threads. any novacom/novaterm stuff doesn't work, the files won't delete so when trying to recreate they just error saying it already exists.
if the devices is on in androind the adb can find the device although the "Serial" has a bunch of ???? at the end of it. when i go to cwm adb cannot find the device.
in cwm i can mount and add files that way and go back to install zip sdcard but get:
Code:
--Installing /sdcard/aokp_tenderloin_milestone-4.zip
Finding update package...
Opening update package...
E: Can't open /sdcard/aokp_tenderloin_milestone-4.zip
(bad)
Installation aborted
used "remove android" in webos, but then nothing is different after the fact as usual. 'tailor' doesn't seem to exist anymore in preware at least that i can find
not sure if there is anything else I can do at this point
plasticsoldier said:
i have the 32gb version. i assume US and Canadian aren't gonna make a difference
i've tried all those threads. any novacom/novaterm stuff doesn't work, the files won't delete so when trying to recreate they just error saying it already exists.
if the devices is on in androind the adb can find the device although the "Serial" has a bunch of ???? at the end of it. when i go to cwm adb cannot find the device.
in cwm i can mount and add files that way and go back to install zip sdcard but get:
Code:
--Installing /sdcard/aokp_tenderloin_milestone-4.zip
Finding update package...
Opening update package...
E: Can't open /sdcard/aokp_tenderloin_milestone-4.zip
(bad)
Installation aborted
used "remove android" in webos, but then nothing is different after the fact as usual. 'tailor' doesn't seem to exist anymore in preware at least that i can find
not sure if there is anything else I can do at this point
Click to expand...
Click to collapse
ok no one will be able to help you fix this issue unless you give complete details of the problems. when you say " novacom/novaterm stuff doesn't work" we cant really help specific error details is what i need. I dont mind helping you fix this but you have to be a little more specific on exactly what,where, and how youre installing and running and mounting apps and directories.
your problem IS fixable but you need to slow down and really do things exactly step by step.
Ok so back to ./adb. now when you boot in to CWM recovery on he touchpad DONT do anything in CWM just plug it into the computer. do not mount it as a usb storage and dont mount or unmount the sd partition LEAVE IT.
you can then use ./adb from the command line or terminal on the computer to move the files to the touchpad' or install apk's uninstall apk's you name it. This will require that you know some linux terminal commands. for example to move a new rom zip to the internal sd card or into any other folder you can use ./adb push command to run a root shell on the android device itself you can use ./adb shell and then change folder and file properties from readonly to rw. this can all be done while the touchpad is patiently waitng in CWM recovery. this way when youre done installing or uninstalling apps from the device and moving flash zips to it, you can disconnect the .adb connection with ./adb disconnect or just type exit from the terminal till it closes. unplug it then you will be able to pick up the touchpad and install zip from the sdcard, keep in mind you dont want to choose 'apply u[date from sdcard' you want to use the 'install zip from sdcard option' you can read up more on how adb works. it is probally the most important part of hacking android.
with that being said. novaterm is the palm webos version of .adb. this is why when you boot into webos recovery to do things like acmeinstaller and acmeuninstaller2 the novaterm novacom and novacomd apps have to be installed correctly on the computer or else you wont be going anywhere fast. some screenshot examples of how it should appear below.
https://www.box.com/s/432e63a83215f00eea6a
https://www.box.com/s/970bc29542a05f98f036
https://www.box.com/s/63c0f656e8354f7f2d6a
https://www.box.com/s/cbe3266467ae8e3ebabe
https://www.box.com/s/005e56a61a178dd17fa4 some better resolution images.
Plasticsoldier said
used "remove android" in webos, but then nothing is different after the fact as usual. 'tailor' doesn't seem to exist anymore in preware at least that i can find
not sure if there is anything else I can do at this point
Yes there is
Firstly tailor does exist, it is a beta and the facility to dl must be enabled.
Read this and scroll down to Enabling beta test feeds and follow the instructions , when you get as far as using the Linux command you CAN copy and paste thank God.
http://en.m.webos-internals.org/wiki/Testing_Feeds?wasRedirected=true . After that reboot into Webos and launch preware. Go into managed feeds as per the instructions in the link above and install Tailor. Reboot again and the app will work. It looks very good actually.
But before attempting to actually use Tailor please read the article I have posted below it is only 7 pages long but will explain how to use Taylor properly as it is a powerful tool.
http://forums.webosnation.com/webos...partition-filesystem-editor-beta-testing.html
I have done all of this , this morning so if you have any problems pm me or ask in this thread.
I sincerely hope that this helps, it should be the answer to your problems.
@haxin: sorry, wasn't trying to be unhelpful when everyone is being helpful to me. I shall be more detailed in future responses. I think i was getting frustrated and had had a busy exhausting day so it didn't help me come across clearly/properly.
OK, so I had preware installed already, so I removed it, went into developer mode, used the linux commands, reinstalled preware, added Tailor.
(i've done this a few times, because I didn't remove the cable after doing the linux commands for preware, then i accidentally hit the wrong buttons and it connected to 'usb drive' mode and wouldn't connect on the pc side and got stuck on the "ow disconnected me properly next time" screen).
So it gives me the following options
USB (media)
Android (system)
Android (cache)
Android (data)
Unused Space
the 'usb media' starts mounted and will mount again if unmounted. If I use 'check filesystem' it'll pass. So then I try 'delete partition' which pretends to delete, then it takes me to the unused partition which is still at 16mb. so i try to use "check filesystem' again and it fails. try repair and it fails as well
I've tried mounting the android parts just to see, they just sit there processing that they are trying to mount. trying to delete or anything else fails as well.
and now after trying things, any of the 'cards' will try to open and just sit there grey. and with my usb cable not plugged in it still is giving me the option to enter usb drive mode. and with this i have to restart and go through the steps again of adding Tailor which is getting tedious.
I restarted, went through the motions to get back to Tailor. trying out resizing just to see how that goes. So far 15%. not sure what will happen when done, but we will see.
This is getting long, so i'll end this part and update on anything and also try to familiarize myself with adb a tad more
Hey all!
I've been pretty frustrated with this issue and I've been browsing around and couldn't find any answers for it.
First off:
I rooted with my Xperia T with the Bin4ry_v31 Root method.
I then installed 3D Chainfire for my device and after installing the drivers for the program it told me to restart my device.
After it restarted it was stuck in the Boot Loop so I went to PC Companion to "repair" my phone. After downloading the appropriate file it updated my phone with v.9.1.A.0.489
The update solved my Boot Loop problem but now my Touch Screen doesn't work, physical buttons turns on but I cannot select anything.
Is there a solution to this problem?
Thanks in advance
PS. I don't think I even downloaded Clockwork or anything for it... just the root software. I'm thinking that I just need to re-root my phone and it should work?? I dunno... I tried to re-root it but it wouldn't let me because now my phone isn't in USB Debugging Mode.
GabrielTONE2 said:
Hey all!
I've been pretty frustrated with this issue and I've been browsing around and couldn't find any answers for it.
First off:
I rooted with my Xperia T with the Bin4ry_v31 Root method.
I then installed 3D Chainfire for my device and after installing the drivers for the program it told me to restart my device.
After it restarted it was stuck in the Boot Loop so I went to PC Companion to "repair" my phone. After downloading the appropriate file it updated my phone with v.9.1.A.0.489
The update solved my Boot Loop problem but now my Touch Screen doesn't work, physical buttons turns on but I cannot select anything.
Is there a solution to this problem?
Thanks in advance
PS. I don't think I even downloaded Clockwork or anything for it... just the root software. I'm thinking that I just need to re-root my phone and it should work?? I dunno... I tried to re-root it but it wouldn't let me because now my phone isn't in USB Debugging Mode.
Click to expand...
Click to collapse
press power button and vol up button simultaneously for few seconds until 4 vibrate and your phone will turn off; then power it on; if this won't not solve the problem repair it again or use flashtool to flash other firmware for this device
Please read this thread and especially post #11 in it.
Please use search in the future. "Loss of touch screen" brings up ALL the threads already started about this issue and the one with the solution in it that all the other threads are directed to.
The Volume Up+ Power button didn't do much to help out.
Greg- I'll read the post later on tonight when I get an internet connection.(using [email protected] work) I skimmed over the posts and didn't seem to understand much but I'll look at it more indepth and hopefully I can figure it out. Ill keep you guys posted.
Thanks for the fast responses!
GabrielTONE2 said:
The Volume Up+ Power button didn't do much to help out.
Greg- I'll read the post later on tonight when I get an internet connection.(using [email protected] work) I skimmed over the posts and didn't seem to understand much but I'll look at it more indepth and hopefully I can figure it out. Ill keep you guys posted.
Thanks for the fast responses!
Click to expand...
Click to collapse
If you need some help I am happy to talk you through it.
Just make sure you adb drivers installed on your PC/laptop
Basically once you have that set up you just need to type those commands into a command window.
gregbradley said:
If you need some help I am happy to talk you through it.
Just make sure you adb drivers installed on your PC/laptop
Basically once you have that set up you just need to type those commands into a command window.
Click to expand...
Click to collapse
I'm gonna be near a computer soon and I would like to confirm the steps that you have suggested me to take according to your link thread:
First- I should download the ADB Driver(universal android USB driver) -Q: I'm wondering if it will still work with my android USB debugging set off?(newbie question?)
Second- I should open the program and plug my phone in -Q: do I have to do anything special to my phone before I put it in? Ex. Power off the phone and hold the volume down button before connecting the USB
I'm assuming that once ABD recognizes my phone a line in the command should read:
C:\Android>adb devices
List of devices attached
"My Device" device
Then I should copy and paste this:
C:\Android>adb shell
[email protected]:/ $ su
su
[email protected]:/ # rmi4_fwloader -b /system/etc/firmware/touch_module_id_0x32.img
-d /sys/bus/rmi4/devices/sensor00 -r -f
rmware/touch_module_id_0x32.img -d /sys/bus/rmi4/devices/sensor00 -r -f <
[email protected]:/ # reboot
reboot
C:\Android>
Then afterwards my phone should reboot and have solved the touch screen problem?
I just wanna make sure that I'm doing it correctly before I attempt this method since this is completely new to me.
Greg; you are a good guy!
replied via 1 off the 2 PM's you sent.
You only need to post here or send me one PM, no need to contact me via three ways
Hi, I have SGS I9000 for over 2 years now, and today, I unlocked it and it just started to reboot, by itself. As far as the start goes is moment when it needs to switch between "starting aplicatios" and home screen. Then he goes again into starting android mode (it doesn't turn off completly, just android reeboting). It worked fine before seconds before.
I have MIUI android V4 and I've tried everything, wiping, restoring, but main problem is that I have some unsynced contacts and sms that I need but I can't access them. Can you help me please? (only way I can access internal storage is boot/mount/mount USB, because of the restarting thing)
something must be segfaulting everytime it comes to load the UI, what does adb logcat say?
Could you please tell me how to check adb logcat? I don't know much about phones but I'm willing to learn
unzip the adb package below, open a command prompt in that directory and type adb.exe logcat
you need Android Debug Bridge drivers installed, windows should do the job for you, unless you're on crappy vista
if it gets stuck on - waiting for device - you don't have those drivers
Tank you SuicideFlasher on your replies but I managed everything by my self :victory: I flashed my phone with Odin and got semaphore kernel, but it got stuck in a boor loop again. I then copied restore folder from my computer to internal storage (that i previously saved there), reinstalled CWM with Odin and restored the system that worked (I backup ed all data) and now I completely formated my phone to start over. Congrats if any of this makes any sence but it worked for me :good:
it's good to see beginners trying to fix stuff by themselves :good: you have good probabilites of becoming a dev one day imo
anyway, by using logcat you would just have watched the phone freak out in that bootloop while seeing in detail whatever the log could tell you, but i think that log would have frightened the hell out of you if your knowledge is really that minimal atm