[Q] Download Mode Gone?? WTF - Captivate Q&A, Help & Troubleshooting

So I recently made a thread how adb wasn't working and that evolved into not being able to get into download mode. Now after not being able to get into download mode for days, I'm still stuck on cm7 with no way of getting back to stock. 3-button recovery won't work, the only way to get into recovery is adb reboot recovery. No button and cable methods work to get phone into download mode as well as adb reboot download. I even recently tried http://www.youtube.com/watch?v=lojU5bvGz3c which is a makeshift usb jig. I successfully made it but it would only turn the phone on. WTF. I'm afraid to buy a real usb jig from online because it most likely will cause the same thing. What is there to do? I'm completely lost. The phone works, the rom is okay I just cannot get back to stock and get rid of cm7. There are lots of issues I need to fix and cannot because of this. Any ideas?????
EDIT: Now I'm completely f'ed. I tried flashing cm7 instead of MIUI again to try once more if I would have better luck on just cm7, but during flash in cwm the phone turned off because the battery compartment was loose and now the phone boots up and goes into recovery shows some code then turns off again

(This post just in case anyone missed the reason in the edit)
Reason: EDIT: FIXED! Don't know what happened. Rearranged resistors and tried again and finally got it
Click to expand...
Click to collapse

I just went back to cm7/miui and it happened again. Nothing to get into download mode is working. What's wrong with cm7 on my phone?

mikel.canovas said:
I just went back to cm7/miui and it happened again. Nothing to get into download mode is working. What's wrong with cm7 on my phone?
Click to expand...
Click to collapse
What's your process to get CM7/Miui installed?
On a side note, ADB won't connect to your device unless you have the Nexus S drivers installed on you computer when CM7/Miui is installed

When I was last on cm7 adb reboot download doesn't work.
Drivers installed
Just sayin
Sent from my unbrickable cappy *bam*

yeah, i distinctly remember the first CM7 build threads that came up here saying that adb reboot download DOES NOT work, and you DO need working 3 buttons or a jig
not sure why that was removed from the threads

A jig should work
You might be coming into contact with the resistors (I can't watch that youtube video from work--firewalled--so I don't know what the setup looks like). Any contact with the them will make it not work. Try insulating them more with some heavy packing tape.
I cut up my mini-usb plug from my car charger (didn't need it), and peeled off all the plastic so I could easily touch the correct two pins with the jig when the hacked up mini-usb is plugged in. Works like a charm. Sometimes if you aren't touching them just right, or if one end of the pin is touching the wrong point the power will come on.
Try harder with the jig, I guarantee you it will work (and you shouldn't have to buy one--it's too easy to do yourself for less than $2 and about 5 minutes).
Good luck!

Just a thought. Are you installing GB boot loaders before flashing CM7/Miui? If so, the way to get into Recovery/Download mode changes. Recovery is vol+/power, Download is Vol-/power.
Just thought I'd toss that out there...just in case

kangi26 said:
Just a thought. Are you installing GB boot loaders before flashing CM7/Miui? If so, the way to get into Recovery/Download mode changes. Recovery is vol+/power, Download is Vol-/power.
Just thought I'd toss that out there...just in case
Click to expand...
Click to collapse
That is only for I9000 GB bootloaders.
On I897 GB bootloaders its still the same as eclair/froyo!
Sent from my SAMSUNG-SGH-I897 using xda premium

b-eock said:
That is only for I9000 GB bootloaders.
On I897 GB bootloaders its still the same as eclair/froyo!
Sent from my SAMSUNG-SGH-I897 using xda premium
Click to expand...
Click to collapse
Yeah, I know, but without all of the details. I figure it doesn't hurt to ask
Sent from a autonomous device

Thanks a ton for the info on GB i've been beating my head trying to get my Mesmerize flashed to a rooted EH09. The vol down button was teh trick i needed.

No download Mode after I897 GB Bootloaders on CM7
Hi there, i've got a question. If i can't get into download mode using the 3 button combination nor the Vol- + Power nor the connect+press buttons+insert baterry trick , do i have chance to get into download mode using the YIG? Thank you
I've lost the 3combo after installing the GB bootloaders with CM7 but the Odin Connection was lost on the SBL, The phone is not even Powering on anymore

If your phone has no signs of life at all, then sadly you are hard bricked...
But it can be fixed through jtag or the unbrickable mod.

So is there hope?
4-2ndtwin said:
If your phone has no signs of life at all, then sadly you are hard bricked...
But it can be fixed through jtag or the unbrickable mod.
Click to expand...
Click to collapse
So if i open the phone and do the unbrickable mod is there a chance to solve the problem? thank you in advance

Yes, according to those that have done jtag or the unbrickable mod, these methods are successful. To get better info though, I would recommend going to those specific threads.

4-2ndtwin said:
Yes, according to those that have done jtag or the unbrickable mod, these methods are successful. To get better info though, I would recommend going to those specific threads.
Click to expand...
Click to collapse
Thank you man i'm going to talk with Adam to see if i can solve the problem.

guilleglad said:
Hi there, i've got a question. If i can't get into download mode using the 3 button combination nor the Vol- + Power nor the connect+press buttons+insert baterry trick , do i have chance to get into download mode using the YIG? Thank you
I've lost the 3combo after installing the GB bootloaders with CM7 but the Odin Connection was lost on the SBL, The phone is not even Powering on anymore
Click to expand...
Click to collapse
I don't think you need jtag (but you can look into it). If your phone is able to at least power on, you should be able to use a Jig to get it into download mode. That is what I did with mine when all the options fail.
good luck.

0gravity1 said:
I don't think you need jtag (but you can look into it). If your phone is able to at least power on, you should be able to use a Jig to get it into download mode. That is what I did with mine when all the options fail.
good look.
Click to expand...
Click to collapse
If the phone doesn't show any signs of life (wich it wont if he failed on sbl) Jtag or Unbrickable Mod would be your 2 best bet. (Id use Unbrickable mode since it will protect you from future issues.)

Sorry haven't checked this thread in a while. My process for going to cm7/miui is flashing stock eclair through odin one click, then rooting and installing cwm. From there I just flash the latest nightly or whatever it is. Nothing I'm doing seems to be wrong

The problem is that I should be able to get into download mode without having to use a jig every single time. 3 button combo should work, but it doesn't when using cm7/miui for some reason

Related

I know,Another Bricked Phone...sigh

I had loaded the ginger clone rom and all was well. I then however wanted to swap kernels so i loaded up seitrons cwm 1.5.6 and proceeded to flash through cwm. this has now become the worst day of my life. the phone will not boot past the galaxy s screen. i cannot not get into recovery and both computers now say usb device not recognized when in download trying to flash odin. i am worried that something is corrupted on my phone because not matter how many times i uninstall and reinstall the drivers no luck. i think it is officially bricked and im sol. maybe some great minds can figure it out here.
It's not bricked - issue is trying to get your computer to recognize your phone when in download mode so you can flash it back.
What OS are you running? Also - where did you download the drivers from? Some seem to work better than others.
If you can get to the galaxy screen you might still be able to to get into recovery. pull out the battery and use the 3 button combo. Hold down both volume button then power and let go of the power button after it turns on. then just reinstall the rom
I'm willing to bet you can also get into Download Mode either with button combos, or a JIG. Once in Download, you can use Odin to restore to JF6, and have a working phone to flash around with again.
i can get into download mode no problem. and i think it is quite possible drivers are corrupted on the phone itself. my wifes phone works on the same exact setup. no usb device not recognized error. i have tried the drivers from here and samsung directly with no luck. 3 button combo does not work. sim out sim in battery out and in. but like i said it will just not register with the comp and hers will. so im going to att and seeing about replacing it. but i will see how that goes. ive done this lots of times with no issues ever.
download works
3 button combo does not so no recovery
usb device not recognized error
thanks for the help and keep it coming i will try everything if i haven't already.
Try current usb port
Sent from my SCH-I897 using XDA App
Think I'm in worse shape. Tried flashing just the kernel to get BLN working again (last ROM I put on somehow loaded a non-compatible kernel). Now the phone boots the white ATT screen and just sits there. Can't get it into D/L mode with 3-button and doesn't respond to computer I have been using to flash ROMs for a couple weeks now...
Am I hosed? ANY help would be greatly appreciated...
You could try to use a JIG to force your phone into Download Mode
Okay...well, got into D/L mode finally. Used Odin to get it back to factory. Used the One Click rooter again, except now it boots to recovery 3e, which doesn't let my power button work as the okay button Pulling the battery to reset it, but it will no longer go into D/L mode to use Odin again. It keeps booting to the recovery Utils, which I cant get out of...*sigh*
Thoughts?
at least your able to do something i still cannot get my phone into recovery or to be recognized by the computer. it is not the drivers so i have no idea. i can only think that something got funked up with the kernel flash.
if you are getting into 3e recovery then you are most certainly NOT using the JF6 one click stock
3e recovery comes on JI6 which is the FroYo leak....completely different builds and roms
have you tried a different usb cable? I was having this problem, and the stock samsung cable was B.O. and wasnt working... i tried my blackberry one and all was good
magnumrt562 said:
have you tried a different usb cable? I was having this problem, and the stock samsung cable was B.O. and wasnt working... i tried my blackberry one and all was good
Click to expand...
Click to collapse
i actually tried this yes. i had a blackberry cable from the storm (shivers) that was laying around. tried that but no luck with that or my wifes cable as well. but a good tip for others nonetheless
Pirateghost said:
if you are getting into 3e recovery then you are most certainly NOT using the JF6 one click stock
3e recovery comes on JI6 which is the FroYo leak....completely different builds and roms
Click to expand...
Click to collapse
I just want to quote this to stress the importance.
Thank you, didn't realize that (still sorta new to this)...
I downloaded a zip (I thought from here somewhere) that extracted into the 4 files. Anyone got a link to the JH6 set of files?
I also downloaded DG's "One Click Odin", but it doesn't seem to really do anything when I run it unless I manually load all the files. Also, I don't see a "Master Clean" like the post refer too
are you sure you downloaded the right odin? in the one click version, theres no option to load files at all. only a "start" and "master clear"
make sure the odin one click is open before you connect your phone.
http://forum.xda-developers.com/showthread.php?t=731989
You guys rock! I don't know how, cause I could have sworn I D/L'd it from that link before and I got the generic Odin, but it looks like I have the right one now! Thank you for your patience with us noobs as we start getting into this new world!
glad you got yours working. i have officially given up and receiving a new one on tuesday. i tried everything but somehow someway the phone is not recognized in download mode. oh well have to mess the with new one then lol
zippox180 said:
glad you got yours working. i have officially given up and receiving a new one on tuesday. i tried everything but somehow someway the phone is not recognized in download mode. oh well have to mess the with new one then lol
Click to expand...
Click to collapse
I was having the same problem. Have you tried powering off, start odin, hold both the volume up/down, then plug in the usb to your phone?

phone just bricked nothing turns on

Hey guys need a little help here.
today i was trying to flash apex and fail, then i flash back to stock 2.1
after its flashing the phone does not turn on. nothing showing up.
can't go to the download mode. also tried to connect to the computer.
the screen just complete black.
will a jig work?
How did you try to flash 2.1
Sent from my GT-I9000 using XDA Premium App
i was in download mode and odin it with pit file
chaolanren said:
i was in download mode and odin it with pit file
Click to expand...
Click to collapse
Flashback to 2.1 completed successfully? Which ODIN did u use? What keycombo are you trying
A jig might work but more likely you'll need JTAG. Same thing happened to my phone a week ago and I ended up shipping it off to connexion2005. This is a high risk when changing bootloaders (2.3 -> 2.2/2.1).
watsaa said:
Flashback to 2.1 completed successfully? Which ODIN did u use? What keycombo are y trying
Click to expand...
Click to collapse
It did show blue sign saying it is finished. then the phone shut off itself and never come back on.
I used odin3 v1.0 the old one I always use.
I tried keycombo
Pull battery, put in battery, vol down+power---no work
Pull battery, put in battery, vol down and up+power----no work
Pull battery, put in battery, vol down and up and power then plug usb---no work
Pull battery, put in battery, vol down and up+usb cable no work
Are you sure the battery isnt dead?
ntdb said:
A jig might work but more likely you'll need JTAG. Same thing happened to my phone a week ago and I ended up shipping it off to connexion2005. This is a high risk when changing bootloaders (2.3 -> 2.2/2.1).
Click to expand...
Click to collapse
I repaired your phone and sent it back today also...
mrhaley30705 said:
Are you sure the battery isnt dead?
Click to expand...
Click to collapse
i did test the battery and it is not dead
How far did you get before you f+4'd on your Apex attempt?
I'm guessing bootloaders the key role here. Also did you master clear before you flashed back to eclair, or just straight to odin?
Sent from I'm sure glad Danger went under, else I'd still be on a Mr.Cartoon SK2.
melbourne408 said:
How far did you get before you f+4'd on your Apex attempt?
I'm guessing bootloaders the key role here. Also did you master clear before you flashed back to eclair, or just straight to odin?
Sent from I'm sure glad Danger went under, else I'd still be on a Mr.Cartoon SK2.
Click to expand...
Click to collapse
I didn't master clear just odin flashed
What .tar did you use to flash 2.1? Was it the one with the 3 button fix?
studacris said:
What .tar did you use to flash 2.1? Was it the one with the 3 button fix?
Click to expand...
Click to collapse
it was the one that can solve 3 botton fix problem and if the system flash goes bad, it will save it back
Ok there's where the problem happened. That .tar only contains the sbl.bin (secondary bootloader) with no primary. So now you have a gingerbread primary and a froyo secondary resulting in a hard brick, you're only option now is jtag. Connexion2005 has already posted in this thread, pm him and he'll get you fixed up.
chaolanren said:
it was the one that can solve 3 botton fix problem and if the system flash goes bad, it will save it back
Click to expand...
Click to collapse
You might need Jtag service. BUT before you do that try making/buying a jig since that will be cheaper to check than just sending for Jtag
Don't think a jig can help
Sent from my SAMSUNG-SGH-I897 using XDA Premium App
One thing I found after bricking my phone a few times is you might want to try download mode again. Have Odin running with a full stock rom loaded. Try the battery trick again. Plug your phone into the usb cable, making sure the battery is removed. Hold both volume buttons and insert your battery. Wait a minute while holding the volume buttons. While holding the volume buttons, keep pulling the battery out and putting it back in. Even though nothing shows up on the phone screen, once Odin did pick up the phone on com and I was able to flash it.
worth a shot. I was ready to send my my phone in for jtag, but persisted and got lucky.
If you flashed Gingerbread bootloaders, then flashed 3 button fix, you hard bricked it. Only way to revive it is with jtag.
anybody know anyone has jtag service in Los Angeles?
The captivate is one if the most difficult phones to jtag, and flute that reason, The only place I know of that can jtag a captivate is
mobiletechvideos.com.

[Q] What kind of brick would this be considered and steps to fix it

My Captivate is currently in a state where it can boot up and it reaches the Cognition boot screen and does nothing further. When trying to use the 2 button+usb cord method to enter download mode the phone loads the charging battery but the animation is frozen.
Would this be considered a soft or hard brick? I'm not familiar with the factors that constitute the differences between the two. Is is a soft brick because the phone can still turn on or is it a hard brick because download mode is unreachable?
I was a user of Cognition 5 v1.00 but as support of the rom by the developer seemed to waiver I felt myself looking for a new GB Rom for my phone. I first flashed Cognition 4.5.3 onto my phone in order to have a stable Rom on my phone until I could decide upon the GB Rom I wanted to try. I decided to flash CM7 and began following the steps outlined in the thread. I formatted my system, data, and cache partitions but upon reboot I reached the point where I am currently.
I have not yet tried the jig as I do not have it on hand at my school apartment. Button combos, the usb cord, and the one click unbrick have not solved the problem and I would like to know if their are any other methods I could use to enter download mode until I am able to procure my jig and try that method.
Any help would be greatly appreciated.
Soft Bricked
You are whats considered soft bricked. Id recommend pulling out battery, SIM and SD. Open odin with with admin rights. Plug your phone to the computer, press volume up and down and insert battery. If that doesn't work then I would suggest making/buying a jig and flash back to stock (eclair, froyo or GB). As to how to get CM7 to work I can't offer any help since i haven't used it in a while and flashing method changed. I can recommend Atomic Fusion, KF1 based and very nice (after u theme it)
Clay
+1 I agree with prbassplayer. You have to get into dl mode and if none of the key combos work, then a jig is probably the only way. I use one and it works great in exactly the situation you seem to be in.
edit: Sorry for the double post, forget this and read next. :-/
Clay?
+1 I agree with prbassplayer. You have to get into dl mode and if none of the button combos work for you then the jig may be you're only option. I use it and it works great in exactly the same situation you seem to be in.
You might have crossed up some files and such from going back and forth between GB and Eclair. So need to flash back to stock and start over with fresh install.
If you're still interested in CM7, after rooting, you can install Rom Manager and follow the install process in the CM7 OP or check out their website, it'll walk you thru the whole thing.
Hope this helps
prbassplayer said:
You are whats considered soft bricked. Id recommend pulling out battery, SIM and SD. Open odin with with admin rights. Plug your phone to the computer, press volume up and down and insert battery. If that doesn't work then I would suggest making/buying a jig and flash back to stock (eclair, froyo or GB). As to how to get CM7 to work I can't offer any help since i haven't used it in a while and flashing method changed. I can recommend Atomic Fusion, KF1 based and very nice (after u theme it)
Click to expand...
Click to collapse
Thank you for the input. At this point it seems that the jig is the only option as I've already tried the usb cord volume up and down process to no avail. I already own a jig, I just need to find a way to my parents house to go grab it.
They aren't hard to make to be honest and if u have a micro usb cable u don't care for it only cost w/e resistors cost for you there.
Using the SDK to use adb commands to get into download mode isn't an option as mentioned in this thread here?
http://forum.xda-developers.com/showthread.php?t=819105http://forum.xda-developers.com/showthread.php?t=1198270&highlight=soft+brick#
TheDeveron said:
Thank you for the input. At this point it seems that the jig is the only option as I've already tried the usb cord volume up and down process to no avail. I already own a jig, I just need to find a way to my parents house to go grab it.
Click to expand...
Click to collapse
If you've already installed the GB bootloaders, the button combination has changed. I believe it is just volume down-power for gingerbread. Try that or volume up-power then release once the logo starts to see if that gets you into download or recovery.
trekie86 said:
If you've already installed the GB bootloaders, the button combination has changed. I believe it is just volume down-power for gingerbread. Try that or volume up-power then release once the logo starts to see if that gets you into download or recovery.
Click to expand...
Click to collapse
That's if he installed I9000's bootloaders. Im assuming he is on I897 bootloaders if he came from Cog 5.
TheDeveron said:
My Captivate is currently in a state where it can boot up and it reaches the Cognition boot screen and does nothing further. When trying to use the 2 button+usb cord method to enter download mode the phone loads the charging battery but the animation is frozen.
Would this be considered a soft or hard brick? I'm not familiar with the factors that constitute the differences between the two. Is is a soft brick because the phone can still turn on or is it a hard brick because download mode is unreachable?
I was a user of Cognition 5 v1.00 but as support of the rom by the developer seemed to waiver I felt myself looking for a new GB Rom for my phone. I first flashed Cognition 4.5.3 onto my phone in order to have a stable Rom on my phone until I could decide upon the GB Rom I wanted to try. I decided to flash CM7 and began following the steps outlined in the thread. I formatted my system, data, and cache partitions but upon reboot I reached the point where I am currently.
I have not yet tried the jig as I do not have it on hand at my school apartment. Button combos, the usb cord, and the one click unbrick have not solved the problem and I would like to know if their are any other methods I could use to enter download mode until I am able to procure my jig and try that method.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
download mode thru adb is a good idea...
or gb key combo for download mode as someone else also menioned...coz u r already on gb bootloaders..
prbassplayer said:
That's if he installed I9000's bootloaders. Im assuming he is on I897 bootloaders if he came from Cog 5.
Click to expand...
Click to collapse
but i think gb bootloaders...be it i9000 or i897....hav the same key combo to get to download mode..i m sorry if i m wrong..as i m on i9000 bootloaders...
^^^ you are wrong, the captivate boots have the same combos they've always had eclair/froyo/gingerbread
Only the I9000 boots have different combos.
studacris said:
^^^ you are wrong, the captivate boots have the same combos they've always had eclair/froyo/gingerbread
Only the I9000 boots have different combos.
Click to expand...
Click to collapse
as i already said...may be i m wrong..
thanx for the info...though i m on cappy ..but first gb botlaoders i had was i9000 while flashin apex..and m still on it....so didnt pay attention
i m using xda classin.so dont hav thanks button..so thanx here only..
killer_raj said:
download mode thru adb is a good idea...
or gb key combo for download mode as someone else also menioned...coz u r already on gb bootloaders..
but i think gb bootloaders...be it i9000 or i897....hav the same key combo to get to download mode..i m sorry if i m wrong..as i m on i9000 bootloaders...
Click to expand...
Click to collapse
No on Cog it is not. You can use the 3 button method just fine.
FYI GB bootloaders are not designed for CM7. CM7 used Froyo based bootloaders for its roms.

I Think I am Bricked

After looking for quite a few hours on google and xda the only solution thats shows up is to use a jtag and quite frankly that scares the pants off me
here is what happened
-i upgraded the device to froyo then did the super one click root in order to root
-after that i installed the modified recovery to turn off the signature check
-after doing that i flashed clockwork mod renamed update.zip through recovery
-after that i flashed the ICS beta but i could not get the main zip to work through recovery the only other zip i had on my sd card was the kernel so i flashed that and it worked, in clockworkmod 5.0 it wiped everything on the phone so i reloaded the 2 zips i flashed the rom there and it rebooted. (this is out of order from the thread so i know this is what causes the next problem.
now when ICS boots up i get an encryption unsuccessful screen saying i need a factory reset, only option given is reboot now. can't bypass the screen, can't access via adb (driver install fails on windows too), cant get into download mode, and can't get into recovery.
how screwed am i
device is
Samsung captivate
-build number 1009
You need Gingerbread bootloaders.
And since you cant get into download mode... You probably need a USB Jig.
Good news is that you see something at startup. I doubt you are totally screwed then.
Second the jig as an option. It has quite the track record on this forum as making the captivate almost un-brickable.
What have you tried as far as getting your phone into download mode? There are sometimes multiple ways (Vol-up + Vol-down while plugging in USB without battery, sim, or microsd installed is how I always seem to get it working). Here is a list:
http://samsungcaptivate.wikia.com/wiki/Putting_the_Phone_into_Download_Mode
To my knowledge, none of that information is dated... but there are those here that know far more about it than I ever will.
none of those methods worked, it just stinks if it would have been any other rom i would have been fine i think but since i can't do anything in user space and everything i do takes me to the ICS android screen i cant do anything.
also for the record i am a noob to samsung devices but i have been doing this stuff to HTC devices for years
Why does he need GB bootloaders?!?
And just boot into recovery factory reset.
Sent from my SGH-I897 using xda premium
b-eock said:
Why does he need GB bootloaders?!?
And just boot into recovery factory reset.
Sent from my SGH-I897 using xda premium
Click to expand...
Click to collapse
I have no recovery or download mode or atleast nothing is letting me into them
Sent from my Touchpad using Tapatalk
b-eock said:
Why does he need GB bootloaders?!?
And just boot into recovery factory reset.
Sent from my SGH-I897 using xda premium
Click to expand...
Click to collapse
He flashed ICS over froyo... are froyo bootloaders compatible?
Im assuming not and thats what caused the brick. Either that or CWM5 doesnt like froyo BL's. Either way.
erbsmokah said:
He flashed ICS over froyo... are froyo bootloaders compatible?
Im assuming not and thats what caused the brick. Either that or CWM5 doesnt like froyo BL's. Either way.
Click to expand...
Click to collapse
They are compatible...
Sent from my SGH-I897 using xda premium
Did you try this method to get into download mode?
1. Turn off phone, remove sim, battery, sd
2. hold both volume buttons, keep holding for remainder of instructions
3. insert usb
4. insert battery
This has instantly granted download mode on every captivate i've ever tried.
b-eock said:
They are compatible...
Sent from my SGH-I897 using xda premium
Click to expand...
Click to collapse
The team hacksung project might be compatible, but the straight port says in the op that you need to flash kf1 first, which included bootloaders.
You aren't hard bricked and your device is recoverable.
If you are still on the froyo bootloaders, try unplugging the usb cable, removing the battery, sim and sd cards, hold vol up+vol down (don't hold power), and plug the usb cable back in. It should take you to download mode.
If your phone responds to adb while it's booting, you can just issue a quick 'adb reboot download' or 'adb reboot recovery' to get it to boot into either without the button combos.
If either of those don't work, you can try forcing it with a usb jig (just a 301k resistance over pins 4 and 5 of the microusb port). Build a jig, take the battery out, plug the jig in, make sure not to touch the jig while it's in or you'll change the resistance and won't work, put the battery back in and it should kick your phone into download mode. Once you're there, simply remove the jig and plug the usb cable back in.
Sometimes the download mode graphic won't show up even if you are actually in download mode. If the phone looks like it hung, try connecting it to Odin anyway and see if it recognizes it.
Edit: forgot to mention, try using adb from linux (virtual machine or livecd will work too). You shouldn't have to mess with drivers and it's worth a shot.
modest_mandroid said:
You aren't hard bricked and your device is recoverable.
If you are still on the froyo bootloaders, try unplugging the usb cable, removing the battery, sim and sd cards, hold vol up+vol down (don't hold power), and plug the usb cable back in. It should take you to download mode.
If your phone responds to adb while it's booting, you can just issue a quick 'adb reboot download' or 'adb reboot recovery' to get it to boot into either without the button combos.
If either of those don't work, you can try forcing it with a usb jig (just a 301k resistance over pins 4 and 5 of the microusb port). Build a jig, take the battery out, plug the jig in, make sure not to touch the jig while it's in or you'll change the resistance and won't work, put the battery back in and it should kick your phone into download mode. Once you're there, simply remove the jig and plug the usb cable back in.
Sometimes the download mode graphic won't show up even if you are actually in download mode. If the phone looks like it hung, try connecting it to Odin anyway and see if it recognizes it.
Edit: forgot to mention, try using adb from linux (virtual machine or livecd will work too). You shouldn't have to mess with drivers and it's worth a shot.
Click to expand...
Click to collapse
i will try it out the jig is the last thing i want to do, luckily this isnt my everyday phone but i would like to get it working hopefully
thank you everyone for the help expect me to hit some thank buttons soon
Were you able to get this working again? If so, how? My Captivate with Build 11 of ICS that had been running perfectly for a week got the message you saw regarding encryption.
I couldn't reset, I tried one click back to stock, and now I just get messages saying can't mount /dev/block/mmcblk0p1.
Unbricking Cappy
Are you able to go to CWM using the three button combo? Try pulling out the battery, reinsert, Hold vol-up + vol-down
and hit power button. Let me know whether CWM menu is appearing or not
All I have to say is wow, not one of those things are true
UCKF1 was the first GB leak for the Captivate, not official Froyo wtf :S
you also don't just connect and power on?!
Who ever needs help, don't listen to this dude, he obviously doesn't know his facts!
Short answer is problem was solved by my friend having a jtag jig
Sent from my PG86100 using XDA App
thoughtlesskyle said:
Wait who is this directed at, if its at me cool dude sorry for asking for help, the answer you have given has been invaluable to solving the problem. This was solved turns out a friend of mine had a jig, glad you went out of your way to lend a useless opinion
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
Yahh you meed to edit your post, that wasn't to you it was to ROMMaker. So don't get your panties in a wad.
Sent from my SGH-I897 using xda premium
b-eock said:
Yahh you meed to edit your post, that wasn't to you it was to ROMMaker. So don't get your panties in a wad.
Sent from my SGH-I897 using xda premium
Click to expand...
Click to collapse
I don't know what good editing my post will do since you quoted it but sure
Sent from my PG86100 using XDA App
Other people who have this issue, try this:
http://forum.xda-developers.com/showthread.php?t=1447303
thoughtlesskyle said:
Short answer is problem was solved by my friend having a jtag jig
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
Hey,
Could you tell us more about how it was resolved?
I'm having the same issue here.

[Q] No Recovery mode and No Download mode.

Hello XDA peeps,
So here is my situation, some days ago (like 3-4 months ago) I installed CM 10.1 on my Captivate. Everything went well and I can even open my phone and use it. But the problem was, after installing that ROM, I no longer can get into recovery mode or download mode. I tried everything possible, the button combo method, button combo and battery pull in method, button combo and USB pull in method and also tried ADB "restart recovery / reboot download" I think, (does not remember because it was 3-4 months ago). Tried everything correctly and stopped trying when I could not get into download mode or recovery mode. The last option I have is a USB jig, but the thing is I don't have it and I will need to buy it from abroad if I want it.
Some more information: When I try to put it in download mode, it gets in a boot loop (I see the AT&T logo and then reboots), the boot loop stops when I leave the buttons. And also when I switch on the phone, it does display the battery charging animation.
And also I've heard some people saying that it might be because I flashed some incompatible kernal or something. (This might be true, because I also don't remember what I did to flash the ROM )
So, I want to fix this now because I want to update my phone to the CyanFox 4.3 ROM which seems very cool . Is there anyway I can fix this recovery mode or download mode on this phone so that I could flash a new ROM to my phone (without the jig if possible)
Thank you lots peeps.
vinte007 said:
Hello XDA peeps,
So here is my situation, some days ago (like 3-4 months ago) I installed CM 10.1 on my Captivate. Everything went well and I can even open my phone and use it. But the problem was, after installing that ROM, I no longer can get into recovery mode or download mode. I tried everything possible, the button combo method, button combo and battery pull in method, button combo and USB pull in method and also tried ADB "restart recovery / reboot download" I think, (does not remember because it was 3-4 months ago). Tried everything correctly and stopped trying when I could not get into download mode or recovery mode. The last option I have is a USB jig, but the thing is I don't have it and I will need to buy it from abroad if I want it.
Some more information: When I try to put it in download mode, it gets in a boot loop (I see the AT&T logo and then reboots), the boot loop stops when I leave the buttons. And also when I switch on the phone, it does display the battery charging animation.
And also I've heard some people saying that it might be because I flashed some incompatible kernal or something. (This might be true, because I also don't remember what I did to flash the ROM )
So, I want to fix this now because I want to update my phone to the CyanFox 4.3 ROM which seems very cool . Is there anyway I can fix this recovery mode or download mode on this phone so that I could flash a new ROM to my phone (without the jig if possible)
Thank you lots peeps.
Click to expand...
Click to collapse
Download and recovery mode aren't affected by ROM flashing. If you can run your phone just fine, then your kernel is fine.
Now my guess is that one of your button isn't working properly, or that you're using the wrong combo. That being said, when you hold the power button (while phone is powered on), you should have an extended menu that gives you the option of booting in recovery or download mode, have you tried those?
As for a jig, you can make one if you don't wanna order one. It's fairly simple and we have a guide in here on how to for just a couple bucks.
BWolf56 said:
Download and recovery mode aren't affected by ROM flashing. If you can run your phone just fine, then your kernel is fine.
Now my guess is that one of your button isn't working properly, or that you're using the wrong combo. That being said, when you hold the power button (while phone is powered on), you should have an extended menu that gives you the option of booting in recovery or download mode, have you tried those?
As for a jig, you can make one if you don't wanna order one. It's fairly simple and we have a guide in here on how to for just a couple bucks.
Click to expand...
Click to collapse
Thank you for your reply. Yes I did try that also. But it just does a normal restart. I tried the the ADB "reboot recovery" also. It also didn't help. I even downloaded an app to reboot into recovery, but no help.
And yesterday I got a jig from my friend, it worked on his infuse but did not work on my Captivate. He said that it might be because he is using a 330K resistor. So I ordered a jig from ebay. It will take some time to reach here.
Is there anything else I can try? maybe push a recovery or something using ADB? Sorry if I am being noob here
Once again, thanks for your support.
At this point i would just wait for the jig. And yes, Samsung galaxy jig requires 301k.
Sent from my SGH-I747 using xda app-developers app
BWolf56 said:
At this point i would just wait for the jig. And yes, Samsung galaxy jig requires 301k.
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Ok, I will wait for the jig and when I get it, I will post the result.
Once again Thank you for your help
Aaaand all of a sudden I was wondering, can this be a bootloader problem? Maybe my bootloader got locked somehow or something?
The best thing is still to wait for the Jig or make one, as BWolf56 suggested.
Once ya have the Jig and If u can get into Download Mode with it, I suggest that u flash the One Click Odin or Heimdall Stock Android 2.3.5 i897uckk4 that includes the Bootloaders. (See the stickied One Click thread in the Dev forum, Post #3). If that is successful, do not flash any Bootloaders again. U can then proceed to flash the KK4 Corn Kernel, the .tar version of the kernel v7.0A, through Odin and then use that CWM Recovery that is baked into that kernel to go on flashin other Roms, etc.
If u cannot get into Download Mode with the Jig, then ur micro usb port of ur phone may be the fault. (But still an app should work from the play store to reboot to download or recovery)...anyway that is all i got for now.
Keep us posted.
Sent from my SAMSUNG-SGH-I747 using Tapatalk

Categories

Resources