Related
There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Hey Guys I know there a lot of threads like the one I am about to start up but those do not apply to what I have done to my phone.
So to start off I know I do not have a lot of posts but that is because I usually find all of the information that I need by reading through the forums. I have experience with flashing various roms onto my captivate. Today I decided I would try out an I9000 rom on my Captivate. I was following the instructions provided by this link
http://forum.xda-developers.com/showthread.php?t=791366
I downloaded the files that the poster said to download. I got to step 2 where I flashed the JM8 PDA. I think this is where I messed up because I after I did this my phone boots directly into recovery and spits some information out. Which is the following (this is the text under the recovery menu options):
update media, please wait ...
update media, finished
# MANUAL MODE #
-- Appling Multi-CSC...
Installing Multi-CSC
mps_dat value: ATT
copy_multi_carrier from: ATT
multicsc : can not access to /system/csc/ATT/system/
copy_common_data
Thats the end of the information spit out by the recovery menu. My problem is that since I flashed some version of the I9000 kernel there is no way for me to enter the download menu so I can restore back to stock. Please Please guys I really need the communities help with this. I am screwed if I take the phone to AT&T because when the phone boots it has the I9000 splash screen that says galaxy s phone gt i9000.
The help will be greatly appreciated and I might even make a donation to the person that can help me!
Yank out battery, close Odin, Remove USB
Open Odin
Insert Battery
Hold Volume down (NO POWER)
Plug in USB
Phone should go into download mode - Start flash
Hey zilch I have tired that as well and I just keep going into the same recovery menu as before. Do you think it might be the fact that I do not have the galaxy s drivers on my computer???
If you can't get into download mode with the button combos (hell, I couldn't) you should still be able to use adb to reboot into download mode. So:
Plug in usb
Open Odin
type from a console in the android sdk tools directory "adb reboot download"
Use odin when you get into the download mode.
Also, Zilch, you've helped me out before, you're the man.
abezapata said:
Hey zilch I have tired that as well and I just keep going into the same recovery menu as before. Do you think it might be the fact that I do not have the galaxy s drivers on my computer???
Click to expand...
Click to collapse
You dont need separate drivers if you had the Captivate ones installed... it should work either way, but if you have no drivers at all, that could be an issue
Edit: If it's plugged into USB and you didnt hit power it shouldn't power on the phone to go into recovery menu... if you did the button combo wrong it should just show the battery
No i do have the captivate drivers installed. I was coming from cognition so maybe that is a problem??? I am really open to any suggestions!
abezapata said:
No i do have the captivate drivers installed. I was coming from cognition so maybe that is a problem??? I am really open to any suggestions!
Click to expand...
Click to collapse
Install the drivers!
I meant I do have the Captivate drivers installed but when the phone turns on and enters recovery mode my computer (windows 7 x64) notifies me it is searching for drivers and then fails.
To get into download mode:
1. Remove Battery, SIM, SD
2. Open Odin
3. hold volume up + down buttons
4. While holding them down, put the battery
5. still holding them(buttons) down, plug the usb cable.
Phone should go to download mode and Odin should detect it.
Zilch25 said:
You dont need separate drivers if you had the Captivate ones installed... it should work either way, but if you have no drivers at all, that could be an issue
Edit: If it's plugged into USB and you didnt hit power it shouldn't power on the phone to go into recovery menu... if you did the button combo wrong it should just show the battery
Click to expand...
Click to collapse
When I plug in the phone it shows the batter and the loading bars for a couple of seconds and then automatically enters the recovery menu. I have not touched any of the buttons the whole time this happens.
abezapata said:
When I plug in the phone it shows the batter and the loading bars for a couple of seconds and then automatically enters the recovery menu. I have not touched any of the buttons the whole time this happens.
Click to expand...
Click to collapse
So if you unplug the phone from USB while it's off, then hold volume down, and plug in USB nothing happens or does it do the battery thing?
Okay so through some miracle of god I got the adb to detect the phone and I sent it into download mode but odin wasnt open and now I am getting the mobile phone image/ warning image/ pc image!
abezapata said:
Okay so through some miracle of god I got the adb to detect the phone and I sent it into download mode but odin wasnt open and now I am getting the mobile phone image/ warning image/ pc image!
Click to expand...
Click to collapse
From that screen if you can't get your button combos to work you're pretty much toast =/
You can try:
USB
Unplug battery
Plug in battery
Hold both volume buttons + power
keep holding the buttons, the screen will turn off, then turn back on
As soon as the screen goes black again, release the power button and hope that you get the android digger
MY PHONE IS FIXED!!!!!!!!!!!! I think what did the trick is I installed Samsung Kies and that gave me all of the drivers for the samsung phone thus giving me the ability to use adb in recovery. Thanks guys! Your'e post encouraged me to keep trying and not cuddle up in the fetal position crying myself to sleep!
Zilch25 said:
From that screen if you can't get your button combos to work you're pretty much toast =/
You can try:
USB
Unplug battery
Plug in battery
Hold both volume buttons + power
keep holding the buttons, the screen will turn off, then turn back on
As soon as the screen goes black again, release the power button and hope that you get the android digger
Click to expand...
Click to collapse
Yeah thanks man once I saw those icons I knew I was good because I have seen them before. Thanks for the help!
abezapata said:
Yeah thanks man once I saw those icons I knew I was good because I have seen them before. Thanks for the help!
Click to expand...
Click to collapse
Whew... well I'm glad you got it back, we've had so many perma-fails lately with the OTA these days it's nice to see a miraculous recovery Improves morale around here!
this thread just saved my life. thank you to everyone that contributed
For future reference, since the button combos are different on the i9000 vs. the Captivate, I've found that I get into download mode every time on an i9000 ROM by yanking the battery, and then re-inserting it while holding volume down+power. I know you already got it resolved, but just keep that in mind, as it has never failed me. Only wish I knew about that combo back during the whole JPC fiasco!
My Phone: Stock Eclair 2.1 JH7 update Build 1006
(amazingly no GPS or shutdown issues)
Rooted
Voodoo Lagfix
That's It.
I read alot on here about upgrading to Froyo, regarding having to un-root and stopping lag fix. I could not figure out how to stop lagfix, which I figured I had to be rooted to do so, so I just didn't un-root either. So my mistake I just said F-It and started Kies Mini and plugged in my phone. My firmware updated and my phone rebooted, however it gets to the Galaxy S screen, and instead of booting up my screen goes black and nothing happens, like it shuts off. So, what should I do from here, as this is my only phone, and I don't have readily available access to a computer.
get to the download mode and reflash to stock using odin.
well that's what I was thinking of doing, however. it seems I can only boot into recovery mode. Vol. Down button and Power button. The three button combo seems to do nothing for me, don't know why. So how do I get into Download mode? My first phone WAS the three button combo.
ConeyKiller said:
well that's what I was thinking of doing, however. it seems I can only boot into recovery mode. Vol. Down button and Power button. The three button combo seems to do nothing for me, don't know why. So how do I get into Download mode? My first phone WAS the three button combo.
Click to expand...
Click to collapse
the key combo may not work on certain build phone. if it happens to your phone, you have to build a jig yourself or buy one (i can send you one, PM me).
ConeyKiller said:
well that's what I was thinking of doing, however. it seems I can only boot into recovery mode. Vol. Down button and Power button. The three button combo seems to do nothing for me, don't know why. So how do I get into Download mode? My first phone WAS the three button combo.
Click to expand...
Click to collapse
fire up ODIN 1-CLICK
connect USB to Computer
remove battery from phone
replace battery
hold down both volume buttons
insert micro USB into phone
*DOWNLOAD MODE!*
Well I sure do appreciate that offer. Vol. Up & Vol. Down button with ODIN open and Then plugging in USB got me to download mode. heh I pushed Master Clear, so we'll see what happens.
THANKS!
I figured that out right before you posted it! you Canadians are alright. lol
I would give you a thanks, but I can't find the button for you!
clemmie said:
fire up ODIN 1-CLICK
connect USB to Computer
remove battery from phone
replace battery
hold down both volume buttons
insert micro USB into phone
*DOWNLOAD MODE!*
Click to expand...
Click to collapse
Been about 15 mins since hitting Master Clear phone still says Downloading... Do not turn off target. I forget, having only flashed once to the leaked, does it usually take this long?
ConeyKiller said:
Been about 15 mins since hitting Master Clear phone still says Downloading... Do not turn off target. I forget, having only flashed once to the leaked, does it usually take this long?
Click to expand...
Click to collapse
you cannot be in the download mode if you just want to do a master clear. boot the phone normally, enable the debug mode and do the master clear using odin there.
No it shouldn't. Another thing that helped was to install the driver package that is included in the Original Post for 1-click. If that still doesn't work after 5 or so minutes, unplug and try again, but this time just go for the ROM flash. You should see the blue status bar moving on the phone. I had the same issue. This took me a few tries.
well odin now says Removed! like i'm supposed to celebrate. phone still says downloading.. lol I guess I should have hit START instead.
Thanks so much clemmie. phone is back to stock you can master clear in download mode, just takes 20 mins. lol I hit start instead and it put me back to the stock jf6. now time to get froyo wee! thanks alot guys, thread can be closed and deleted if you would like.
Hello I accidently went and flashed a s5570i rom into my s5570 and now my phone will not turn on,
or into download/recovery mode.
I have a question will a jig get me into download mode?
Thanks in advance
Also plugged usb in and was holding
Home + power + volume up
and odin detects it but the phone wont flash or turn on and there is nothing on the screen
PhaseCoder said:
Also plugged usb in and was holding
Home + power + volume up
and odin detects it but the phone wont flash or turn on and there is nothing on the screen
Click to expand...
Click to collapse
Download mode is home+power+vol down
Tapatalk 2-vel küldve az én GT-S5570-ről
Yea I know that, but it wont boot to recovery or download mode.
But when I press volume up home and power odin detects it
heyy, the problem already has a solution?
my phone S5570 also has the same problem, black screen, can not go into recovery mode or download mode.
but go to RAMDump (vol up + home + power) and connect it to my PC, my S5570 is detected by the PC and odin, but can not flashing my rom.
stuck in "Setup Connection" I know it because my phone is not in the download mode.
whether the USB JIG is the right solution?
sorry if my language is bad
PhaseCoder said:
Hello I accidently went and flashed a s5570i rom into my s5570 and now my phone will not turn on,
or into download/recovery mode.
I have a question will a jig get me into download mode?
Thanks in advance
Click to expand...
Click to collapse
(I think this set of steps works in these
conditions: Hard-brick, absolutely non-
responsive to any button combination.
Odin still recognizes the phone when
connected through USB port)
1.- Remove both the SIM card and de
microSD card.
2.- KEEP YOUR BATTERY REMOVED
3.- Apply the Download-mode button
combination (known by you all)
4.- WHILE HOLDING THE
COMBINATION, insert the battery, and
keep the buttons pressed untill you get
the download mode.
5.- Flash your phone with a valid
firmware through Odin (Preferebly,
have Odin prepared before doing this
trick).........
hit thanks if this helped you and others....
R: [Q] Hard bricked s5570
Henota11 said:
heyy, the problem already has a solution?
my phone S5570 also has the same problem, black screen, can not go into recovery mode or download mode.
but go to RAMDump (vol up + home + power) and connect it to my PC, my S5570 is detected by the PC and odin, but can not flashing my rom.
stuck in "Setup Connection" I know it because my phone is not in the download mode.
whether the USB JIG is the right solution?
sorry if my language is bad
Click to expand...
Click to collapse
Try to press power+home+vol down+vol up
It'll go to emergency download mode.
Need tester for your rom (Galaxy Mini)? Just pm me! Sent from my BlackdroidLie v1 (My Phone often lies with this rom..)
steexyl said:
Try to press power+home+vol down+vol up
It'll go to emergency download mode.
Need tester for your rom (Galaxy Mini)? Just pm me! Sent from my BlackdroidLie v1 (My Phone often lies with this rom..)
Click to expand...
Click to collapse
and then?
I do not see any change, only detected on my computer
but the screen stays black
Send it to Samsung to repair it or try USB jig
Sent from my GT-S5570 using xda premium
tried jig didnt work, sent it to samsung was back in 3 days fully working
TIP: say you were during a call and phone turned off wouldbnt turn back on. do not mention ROOt or anything else
sir
PhaseCoder said:
tried jig didnt work, sent it to samsung was back in 3 days fully working
TIP: say you were during a call and phone turned off wouldbnt turn back on. do not mention ROOt or anything else
Click to expand...
Click to collapse
how much did you pay ?
hard brick galaxy mini
my galaxy mini also hard brick cannot go to downloading mode or recovery mode .tried jsb jig also cannot any other solution ???????
Same problem.. only solution is bring to ur frend technician, an operation will conduct to ur problem, pay for only 300 pesos here in the Philippines
Sent from my GT-S5570 using xda app-developers app
uploaded wrong rom on galaxy mini s5570,
phone turns off and dead I think,
nothing was working,
I've JTAG the phone from my friend,
phone turns on and able to enter in downloading mode only,
i've uploaded froyo android it failed,
then I uploaded arm11 boot file,
now phone won't be able to enter in DOWNLOAD MODE or recovery mode,
phone turns on and screen went black cannot be able to enter in DOWNLOAD MODE or recovery,
when I connect it to pc with usb cable it automatically turns on and screen turns black,
will usb jig works for it to enter in DOWNLOAD MODE??
please reply me if possible
thanks and regards
Sent from my GT-N7100 using xda app-developers app
---------- Post added at 10:55 PM ---------- Previous post was at 10:42 PM ----------
uploaded wrong rom on galaxy mini s5570,
phone turns off and dead I think,
nothing was working,
I've JTAG the phone from my friend,
phone turns on and able to enter in downloading mode only,
i've uploaded froyo android it failed,
then I uploaded arm11 boot file,
now phone won't be able to enter in DOWNLOAD MODE or recovery mode,
phone turns on and screen went black cannot be able to enter in DOWNLOAD MODE or recovery,
when I connect it to pc with usb cable it automatically turns on and screen turns black,
Odin also won't detecting it
will usb jig works for it to enter in DOWNLOAD MODE??
please reply me if possible
thanks and regards
Sent from my GT-N7100 using xda app-developers app
Jtag it again then try to re install the firmware
Sent from my GT-S5570 using xda app-developers app
brick s5570
I have a Samsung mini S7750, in resetting to factory defaults boot.
Boot mode or recovery mode does not.Only works is a combination of "home + vol up + vol down" moves into some mode where it while Odin detects the two com ports, but nothing to do, Odin hangs on setup conection.
JIG does not work [resistor 301kohm].Display is black.
[cz eng dictionary]
PhaseCoder said:
Hello I accidently went and flashed a s5570i rom into my s5570 and now my phone will not turn on,
or into download/recovery mode.
I have a question will a jig get me into download mode?
Thanks in advance
Click to expand...
Click to collapse
Try the simple just "hold power+home". It'll be leads you to recovery mode, then you should flash the appropriate rom for s5570. Cchopefully help
Sent from my GT-S5570 using Tapatalk
Help please
Hi. My S5570 is hard bricked. Will not turn on in any way i try. Does not go on download or recovery mode. The USB Jig method does not work for me. (I tried with around 3) and I connected my phone to my laptop and help down power + home + vol up and it does not recognise my device but when i do power + home + vol up + vol down it recognises it. I then used Odin to recover it but I have tried over 50 times and it is always stuck on "Setup connection...". Can someone please help? I have already tried re-installing Samsung USB Drivers. Still not working. Please help and thanks!
Kailens said:
Hi. My S5570 is hard bricked. Will not turn on in any way i try. Does not go on download or recovery mode. The USB Jig method does not work for me. (I tried with around 3) and I connected my phone to my laptop and help down power + home + vol up and it does not recognise my device but when i do power + home + vol up + vol down it recognises it. I then used Odin to recover it but I have tried over 50 times and it is always stuck on "Setup connection...". Can someone please help? I have already tried re-installing Samsung USB Drivers. Still not working. Please help and thanks!
Click to expand...
Click to collapse
Only hold vol up+home+power and THEN connect it if download mode works. I mean if it's recognized by the computer, download mode has to work, there is no way. If it does, then flash a stock ROM.
Oh and also something: before doing this, pull out your sd card and even your sim card. The same thing happened to my phone and Odin could flash it after removing everything.
Kailens said:
Hi. My S5570 is hard bricked. Will not turn on in any way i try. Does not go on download or recovery mode. The USB Jig method does not work for me. (I tried with around 3) and I connected my phone to my laptop and help down power + home + vol up and it does not recognise my device but when i do power + home + vol up + vol down it recognises it. I then used Odin to recover it but I have tried over 50 times and it is always stuck on "Setup connection...". Can someone please help? I have already tried re-installing Samsung USB Drivers. Still not working. Please help and thanks!
Click to expand...
Click to collapse
There is another way that u can try:
(Asumming that samsung mobile drivers are installed, with no Samsung KIES... & odin running in the foreground.)
*Remove sim, sdcard & battery.
*Now connect ur phone(without battery) to pc via usb cable.
*Now press the usual download mode keys(volume down & home & power buttons) together without the battery.
*While still holding those three buttons, insert the battery.
At this point Odin should detect ur phone so that u can flash stock firmware.
U can try this atleast since u r left with no choice:sly:.
Good Luck..!!:thumbup:
Hope this helps...!!
hello, I have a problem with my galaxy note 9. I mistakenly started an update with a different firmware from mine (I have SM-N960F). So now it is in bootloop on the screen installing system update. If I press Power + Volume Down the phone can simulate the removal of the battery by switching off and then restarting immediately. I can not get into recovery mode nor download mode. The phone is not recognized by the PC and therefore I can not use odin. How can i do?
Hold down Bixby, volume down, and power button until you see the download screen. Then flash through proper firmware.
if I try this combination of keys the phone will reboot on the logo screen until I stop (and then go back to that of the installing system update)
cosmo.1 said:
if I try this combination of keys the phone will reboot on the logo screen until I stop (and then go back to that of the installing system update)
Click to expand...
Click to collapse
Ok. Try Bixby, Power, and Volume UP. See if you can get into recovery.
no, nothing happens..
If one wants to remove the carrier boot/flashscreen does one just flash an unbranded firmware? hate the carrier startup splash screen...
cosmo.1 said:
no, nothing happens..
Click to expand...
Click to collapse
Dang. That sounds like a hard brick to me. If you can't get into download, there's nothing you can do. Hopefully someone here can find a solution for you, but sounds like you're bricked.
---------- Post added at 08:52 PM ---------- Previous post was at 08:51 PM ----------
Jostian said:
If one wants to remove the carrier boot/flashscreen does one just flash an unbranded firmware? hate the carrier startup splash screen...
Click to expand...
Click to collapse
I think you accidentally clicked on for wrong thread. Your question has nothing to do with the OP's problem.
cosmo.1 said:
hello, I have a problem with my galaxy note 9. I mistakenly started an update with a different firmware from mine (I have SM-N960F). So now it is in bootloop on the screen installing system update. If I press Power + Volume Down the phone can simulate the removal of the battery by switching off and then restarting immediately. I can not get into recovery mode nor download mode. The phone is not recognized by the PC and therefore I can not use odin. How can i do?
Click to expand...
Click to collapse
contrary to what some might have suggested in this case dl mode can only be achieved if phone is OFF. ( on the note 9 dl mode button combo changed so... :cyclops: )
so if you cant get to recovery and select power off. let it drain out. then plug the power for 10 min to charge it. leave it powered off
then unplug. hold vol down and bixby with one hand. while holding those 2 buttons plug the usb cable from your pc.
should revive to dl mode
Mr. Orange 645 said:
Dang. That sounds like a hard brick to me. If you can't get into download, there's nothing you can do. Hopefully someone here can find a solution for you, but sounds like you're bricked.
---------- Post added at 08:52 PM ---------- Previous post was at 08:51 PM ----------
I think you accidentally clicked on for wrong thread. Your question has nothing to do with the OP's problem.
Click to expand...
Click to collapse
Yip, apologies, my bad.
bober10113 said:
contrary to what some might have suggested in this case dl mode can only be achieved if phone is off. ( on the note 9 dl mode button combo changed so... :cyclops: )
so if you cant get to recovery and select power off. Let it drain out. Then plug the power for 10 min to charge it. Leave it powered off
then unplug. Hold vol down and bixby with one hand. While holding those 2 buttons plug the usb cable from your pc.
Should revive to dl mode
Click to expand...
Click to collapse
bro you are the best.. It's work!
Love youu
cosmo.1 said:
bro you are the best.. It's work!
Love youu
Click to expand...
Click to collapse
lol ask mr orange, im actualy the worst
bober10113 said:
lol ask mr orange, in actualy the worst
Click to expand...
Click to collapse
Yes, but I celebrated too early ... now I have another problem. I downloaded a firmware from updato.com and unzipped. I assigned the entries bl ap cl and csc, and started .. now the process is started on "set partition" and on the device the horizontal bar has not loaded. now it is still .. and yet the phone has been recognized.
cosmo.1 said:
Yes, but I celebrated too early ... now I have another problem. I downloaded a firmware from updato.com and unzipped. I assigned the entries bl ap cl and csc, and started .. now the process is started on "set partition" and on the device the horizontal bar has not loaded. now it is still .. and yet the phone has been recognized.
Click to expand...
Click to collapse
you need to know what model phone you have and flash the matching firmware.(get latest)
you can also use samfirm tool to get latest firmwares.
you cant downgraded bootloader so maybe you just choose a too old of a firmware.
also be sure you use Odin v. 3.13.1
also check that you are using a good USB c cable/USB port on PC.
bober10113 said:
you need to know what model phone you have and flash the matching firmware.(get latest)
you can also use samfirm tool to get latest firmwares.
you cant downgraded bootloader so maybe you just choose a too old of a firmware.
also be sure you use Odin v. 3.13.1
also check that you are using a good USB c cable/USB port on PC.
Click to expand...
Click to collapse
Yes.. there was an error non odin 12.3
It's finally work:good:
Glad you got it working. Sorry if I steered you the wrong direction. I wasn't implying you could get to Download mode with it powered on. I assumed you were trying it with the device powered down. I should've been more clear and I almost asked you that.
Glad Bober got you up and running.
Hi all, I got a boot loop on my note 9 n960n after I was enable the "encryption"(didn't think straight..). After I pressed "reset and the phone will go to TWRP recovery but it will not allow me to stop so it just keep looping whenever I press "reset". I cannot power off the phone also. Any advise is appreciated, thanks in advance.
I solved the problem eventually..
same problem here.
wait a lot of hours battery to go down and put in download mode but now odin didn recognize it.
Any advice,please
aaatso said:
same problem here.
wait a lot of hours battery to go down and put in download mode but now odin didn recognize it.
Any advice,please
Click to expand...
Click to collapse
Have you tried:
1. Plug phone into computer, with odin running
2. Turn phone off (if bootlooping skip to next step)
3. Hold bixby and volume down buttons, then turn phone on( or wait for phone to power cycle if bootlooping)
4. You should now be in download mode
if i press power button it will stuck in installing system info again
aaatso said:
if i press power button it will stuck in installing system info again
Click to expand...
Click to collapse
seems you might not have flashed a complete firmware set ( all 4 bl ap cp and csc .md5 files. were you trying to downgrade by any chance?)
also u should state what got you in that jam in the 1st place. because just responding to an old thread dosen't give much info on your current situation.