Related
There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Help guys.
I have a Samsung Galaxy S Captivate I897. Last night I installed the Clockworkmod ROM Manager in there and was messing around with it.
I choose my phone model to be the the I9000 and then I went into recovery mode to restore the previous ROM, but guess what? It went into recovery mode, the volume up and down buttons select the menu items and it asks me to hit the "OK key" to enter.
The Captivate doesn't have an OK key, it uses the power button. So the Android Recovery Mode here thinks the phone is a I9000 and I can't get it to do anything other than reboot into that mode.
I've tried using the ADB to try to get back into download mode but it's no longer reading the phone. The volume + power buttons to go into that mode has never worked for this phone either.
I'm at a loss at what to do. Is there anyway I can get out of recovery mode and into download mode or back to regular phone usage here? Would I need to take it to an android developer?
Thanks for your help.
Thanks for your help.
vancouverguy said:
Help guys.
I have a Samsung Galaxy S Captivate I897. Last night I installed the Clockworkmod ROM Manager in there and was messing around with it.
I choose my phone model to be the the I9000 and then I went into recovery mode to restore the previous ROM, but guess what? It went into recovery mode, the volume up and down buttons select the menu items and it asks me to hit the "OK key" to enter.
The Captivate doesn't have an OK key, it uses the power button. So the Android Recovery Mode here thinks the phone is a I9000 and I can't get it to do anything other than reboot into that mode.
I've tried using the ADB to try to get back into download mode but it's no longer reading the phone. The volume + power buttons to go into that mode has never worked for this phone either.
I'm at a loss at what to do. Is there anyway I can get out of recovery mode and into download mode or back to regular phone usage here? Would I need to take it to an android developer?
Thanks for your help.
Thanks for your help.
Click to expand...
Click to collapse
Shut off the phone, open up odin(DG's flash to stock one) hold the power and the menu button. Once you see the ATT screen release the power while continuing to hold the volume buttons. Once odin recognizes your device flash to stock using the utility. Once this works donate to DG for saving your ass. Also, quit using ROM manager. Just use the update.zip method everyone else uses.
+1 for just using CWM update.zip It is sooo much easier/faster.
Thanks, but it didn't work. My Galaxy S is one of those where the volume + power buttons don't work to get it into download mode.
I did try power + menu as you suggest, but that doesn't work either.
try this
1. open odin.
2. With phone unplugged remove battery
3. with battery removed plug phone into pc via USB
4. with battery still removed simultaneously hold down Vol. + / - (forget about power button just hold down the two vol buttons)
5. While holding down the vol + / - insert the battery (keep the vol buttons down and hopefully DL screen comes up)
silverslotcar said:
+1 for just using CWM update.zip It is sooo much easier/faster.
Click to expand...
Click to collapse
I cannot stress this enough.
Also, OP, if the above doesn't work, it might be USB jig time.
pwr isn't used to go into dload mode - that would turn your phone on.
Do this:
Open odin
Remove bat, sim, ext mem card
replace bat
hold vol -/+ and plug in data cable to computer
(should be download mode)
If that fails, then get yourself a jig... gotta search for the thread though - should cost a couple dollars. Then once you're back up... look up the thread to fix the 3 button combo.
You might try turning the phone off then hold VOLUME DOWN and POWER (not vol up/dwn/pwr) to get into download mode. Make sure to remove the sim and sd cards.
I bricked my phone over the weekend and had similar problem you did.the easiest way too get out in to download mode is a jig. Its easy and cheap to do.look on you tube under un brick captivate fort a tutorial.
Sent from my SAMSUNG-SGH-I897 using XDA App
Question about using update.zip to install clockwork recovery after flashing to stock (and avoiding Rom Manager):
Is rooting still required?
doreyu said:
Question about using update.zip to install clockwork recovery after flashing to stock (and avoiding Rom Manager):
Is rooting still required?
Click to expand...
Click to collapse
Nope. No root needed
mcord11758 said:
Nope. No root needed
Click to expand...
Click to collapse
Awesome, great that would be hugely faster, thanks.
doreyu said:
Awesome, great that would be hugely faster, thanks.
Click to expand...
Click to collapse
Once you learn that trick you are on stock for like 2 minutes before you flash
Yeah I'm kind of a lurk but I've been around for about a month just flashing everything, and I had no idea it could be done like this till today. Going to make my next one even faster.
Sent from my SAMSUNG-SGH-I897 using XDA App
Nothing seems to work.
I'm going to try the jig method Wednesday morning. Wish me luck!
I tried the jig and it didn't work.
What happened was that it got me back into recovery mode, not download mode. Tried it several times. So unless I'm hitting the wrong points on the phone usb plugin (other than the last two), I'm hooped.
I tried the direct resistor wire to points in usb plugin method. I didn't try the one where I cut open a mini-usb cable and use the plug as a dongle, although I think it may get the same result.
What do you guys think?
my phone has been frozen at the samsung i9000 screen ever since opening this app.... i am very new to this do not understand most concepts here.. ie. flashing a rom. If anyone can help me get my phone out of this state or has any suggestions on how i should fix this please comment.
if you can get into recovery mode try flasing another rom via cwm or flash it using odin and download mode (flashing non wipe roms via cwm might leave your apps and data intact)
What is the full name of the app? How did you try using it? Do you know what firmware version your phone is on?
First thing to try is turn off, remove battery sim and any microSD. leave five minutes and put all back in and turn on.
krtken said:
if you can get into recovery mode try flasing another rom via cwm or flash it using odin and download mode (flashing non wipe roms via cwm might leave your apps and data intact)
Click to expand...
Click to collapse
i can get in recpvery and download mode but have no clue really how to flash a rom.. i have odin and a few otehr files but i cannot get this back to normal.
Tehpriest said:
What is the full name of the app? How did you try using it? Do you know what firmware version your phone is on?
First thing to try is turn off, remove battery sim and any microSD. leave five minutes and put all back in and turn on.
Click to expand...
Click to collapse
the app is galaxy s tweaks or something very simalar (black and white logo) the two options i was given in the app were "YES-BREAAAAK my phone" and "NO- Im not crazy" i selected no and then my phone just reset and wouldnt turn on again ive tried everything i can do without hooking up to a comp ( as far as i know) but thx for the advice
Where did you get this from? It does not seem to be in the market.
OK just found it. Have a read off all the comments. Not good.
http://www.appbrain.com/app/gst-(galaxy-s-tweaker)/com.pommedeterresautee.lagfix
You could try restart holding Home Vol up and Power button then choose Clear cache and Factory reset.
or
Try restart the phone holding home Vol down and press power button to get into recovery mode. then plug in and open Kies go to tools and firmware recovery.
Tehpriest said:
OK just found it. Have a read off all the comments. Not good.
http://www.appbrain.com/app/gst-(galaxy-s-tweaker)/com.pommedeterresautee.lagfix
You could try restart holding Home Vol up and Power button then choose Clear cache and Factory reset.
or
Try restart the phone holding home Vol down and press power button to get into recovery mode. then plug in and open Kies go to tools and firmware recovery.
Click to expand...
Click to collapse
Is telling me i need recovery code, I have never received one.
Just read this so it may work for you.
disconnect the phone from USB, pull the battery, replace it, boot into recovery mode and reconnect the phone. Go back to Kies and tools firmware recovery.
In other words repeat what you have done :-s
Original post on Android Forums.
The message indicated that I would need a recovery code that could be obtained later by clicking Tools | Firmware Emergency Recovery Menu.
I was then instructed to disconnect the phone, pull the battery, boot into recovery mode and reconnect the phone which I did. The phone would not reconnect. At this point I called Samsung tech support and wasn't impressed when I was simply told to repeat the procedure. But to my surprise, the upgrade was successful the second time around. Go figure! Anyway, I was wondering if anyone else ran into the recovery code message.
Click to expand...
Click to collapse
Hello people,
I recently installed GalaxySense Rom (Search "oozeroo" on Google) for my Samsung Captivate AT&T, and it was working fine, until I changed a few settings, then it said it was going to Hot Boot, so the hot boot worked fine. Then, I turned off my phone and turned it back on, and it does not boot. I tried some stuff (check the Situations). My phone is stuck at "Galaxy S Cyanogen(Mod)" (Picture Included!!!)
Situation:
-No Download Mode
-No recovery mode
-Flashed this rom with rom manager (wiped dalvik cache only)
-TRIED installing Clockworkmod recovery, but wont work (not booting into recovery)
-Only an internal SD inside phone, 14 Gigs.
(Ask me for more info if needed please)
Thank you so much, and please help.
--DV
dvasavda said:
Hello people,
I recently installed GalaxySense Rom (Search "oozeroo" on Google) for my Samsung Captivate AT&T, and it was working fine, until I changed a few settings, then it said it was going to Hot Boot, so the hot boot worked fine. Then, I turned off my phone and turned it back on, and it does not boot. I tried some stuff (check the Situations). My phone is stuck at "Galaxy S Cyanogen(Mod)" (Picture Included!!!)
Situation:
-No Download Mode
-No recovery mode
-Flashed this rom with rom manager (wiped dalvik cache only)
-TRIED installing Clockworkmod recovery, but wont work (not booting into recovery)
-Only an internal SD inside phone, 14 Gigs.
(Ask me for more info if needed please)
Thank you so much, and please help.
--DV
Click to expand...
Click to collapse
What key combo are you trying for recovery? You have a JIG laying around? If not, I'd go get one regardless of how invincible you think your phone may be. Maybe you could try Adam's one-click unbrick. http://forum.xda-developers.com/showthread.php?t=1153310 I don't know what conditions need to be met for it (your phone) to be recognized, but I'd give it a shot anyway.
I am using:
take out battery, hold both volume buttons, plug in USB, then put in battery, all with both volume buttons held the whole time.
No, I do not have a jig, I want to get one though
-I do not care to erase everything I have, I tried using Odin3 one click downloader, it worked for me once, when my phone actually went download mode
dvasavda said:
I am using:
take out battery, hold both volume buttons, plug in USB, then put in battery, all with both volume buttons held the whole time.
No, I do not have a jig, I want to get one though
-I do not care to erase everything I have, I tried using Odin3 one click downloader, it worked for me once, when my phone actually went download mode
Click to expand...
Click to collapse
remove sim and microsd. You have to have your batt back in before you hold volume+- and insert USB
what recovery key combo you using?
still nothing buddy, tried your technique
thanks dude
i did try returning it, but they didnt accept it (costco), NOT because I had another romm installed... but because it wasnt booting!
-although, I do not have the battery sign show up, it just has the circle, then it goes to galaxy s screen
Twicebak3d said:
What key combo are you trying for recovery? You have a JIG laying around? If not, I'd go get one regardless of how invincible you think your phone may be. Maybe you could try Adam's one-click unbrick. http://forum.xda-developers.com/showthread.php?t=1153310 I don't know what conditions need to be met for it (your phone) to be recognized, but I'd give it a shot anyway.
Click to expand...
Click to collapse
Dont have linux
post as much as you want on this thread, i dont really care
any other ideas?
Well..... has galaxysense been actually ported to the captivate yet? I doubt this'll work but.... try vol down + home + power. You could vary vol down with vol up for recovery mode as well. Like I said.... doubt they'll work.
It has ported to captivate, there is a captivate section on website
Home button? you mean the touchscreen/virtual home button? When do you press it:when it lights up?
-btw, i tried the brick fix thing, but it didnt recognize my phone, because it was only booting
dvasavda said:
It has ported to captivate, there is a captivate section on website
Home button? you mean the touchscreen/virtual home button? When do you press it:when it lights up?
-btw, i tried the brick fix thing, but it didnt recognize my phone, because it was only booting
Click to expand...
Click to collapse
There's a reason I didn't think it'd work lol. Those are i9000 key combos lol. Get a jig imo.
what are the sgh-i897 combos?
can you go into safe mode with this?
and my home button question please?
dvasavda said:
what are the sgh-i897 combos?
can you go into safe mode with this?
and my home button question please?
Click to expand...
Click to collapse
Yeah I meant that virtual key. cappy combos are vol up/down + power for recovery mode for me.
no recovery for me
actually, at first, I had no recovery on my new rom, so... (I dont want to tell you this!) but I looked for a stock recovery, and I put it over the old recovery file in the system.
dvasavda said:
no recovery for me
actually, at first, I had no recovery on my new rom, so... (I dont want to tell you this!) but I looked for a stock recovery, and I put it over the old recovery file in the system.
Click to expand...
Click to collapse
Do you know if you flashed 3 button? try vol up vol down power. hold those while inserting usb
nothing dude yet, i did not flash the 3 button fix, (oops!)
i did notice that, when the phone is booting up, and I connect, the phone is half recognized with computer, and yes I did install drivers.
If i go to device manager, it says Captivate, but with a yellow exclamation mark
have to go to, talk to you tommorow morning!
thanks buddy, i appreciate it!
dvasavda said:
nothing dude yet, i did not flash the 3 button fix, (oops!)
i did notice that, when the phone is booting up, and I connect, the phone is half recognized with computer, and yes I did install drivers.
If i go to device manager, it says Captivate, but with a yellow exclamation mark
Click to expand...
Click to collapse
I wonder if it'd be recognized by ADB if you install Nexus S drivers. try using that as the drivers for the marked captivate in dev manager. http://developer.android.com/sdk/win-usb.html#
If it changes name to Android Composite ADB interface, then you can ADB into recovery and reflash. I don't see how but if you don't have a jig.... might as well try.
(just raised your thanks meter!)
can I cut off an old charger that fits the captivate, and use that?
dvasavda said:
(just raised your thanks meter!)
can I cut off an old charger that fits the captivate, and use that?
Click to expand...
Click to collapse
For a JIG? Possibly. You have to jump pins 4 and 5 with 300k worth of resistors. if you look in my sig, there's also a guide to just making one without a USB. Regardless of how you apply the resistance to your phone, you still need 301k. There is a window. I've seen 294k jigs work, so just as long as resistance is in a certain range across those two pins, it will work.
ok, thanks
I tried adb rebooting, but says error device not found
(same thing happened when my device was working and on)
Hi,
I tried the regular fastboot method to load CWM recovery.
Whenever it got to the point of loading the recovering, it would just say "flashing recovery on the device...".
Then, when restarting bootloader and clicking on "recovery", it would just shut down the phone.
I decided to experiment to try fix the issue, and I came across this post:
http://forum.xda-developers.com/showthread.php?t=1928551
I downloaded the ZIP file and I ran the root.bat
It flashed some boot images and now my phone wont start
It is stuck on the "warning bootloader unlocked screen" and will not go any further.
Please help . I'm so scared that I've bricked my phone. Is there ANYTHING I can do?
Thanks in advance for the help!
The methods u used can't brick your phone
Reboot in boot loader by pressing the power button and volume - button at the same time. Just at the moment the phone shuts-down/reboot release the power button. It will boot in boot loader. After this flash cwm or twrp again and with the volume down button go to recovery. Select recovery with the volume up key and u are done. Cwm/twrp is flashed and will boot in the recovery.
In recovery I would install the ROM from Omar. It will restore your system and boot.IMG so it will work. Don't forget to wipe data.
If this doesn't work flash the home made fast boot files somewhere in the development section
Sent from my XT890 using xda app-developers app
Hazou said:
The methods u used can't brick your phone
Reboot in boot loader by pressing the power button and volume - button at the same time. Just at the moment the phone shuts-down/reboot release the power button. It will boot in boot loader.
Click to expand...
Click to collapse
Thanks - I tried that. I do let go of the buttons as soon as it starts to reboot itself, but it doesn't start the bootloader - it still just shows the screen "warning bootloader unlocked". I can not get back into the bootloader
Do u reset the phone with the 4 buttons and just when it resets does your phone reboots immediately?
Sent from my GT-P5110 using XDA Premium HD app
Hazou said:
Do u reset the phone with the 4 buttons and just when it resets does your phone reboots immediately?
Sent from my GT-P5110 using XDA Premium HD app
Click to expand...
Click to collapse
If I hold all 4 buttons, the screen goes blank, and the green light stays on. My PC then finds hardware called "MEDFIELD" but wont find drivers for it.
Does this help at all?
alkit said:
If I hold all 4 buttons, the screen goes blank, and the green light stays on. My PC then finds hardware called "MEDFIELD" but wont find drivers for it.
Does this help at all?
Click to expand...
Click to collapse
The above applies when connected with usb.
If I press all 4 buttons without USB connected, it just reboots and gets stuck on the "unlocked bootloader" message again
alkit said:
Then, when restarting bootloader and clicking on "recovery", it would just shut down the phone.
Click to expand...
Click to collapse
Just of curiosity - which button you used to select recovery - power button or vol.up button?
alkit said:
I do let go of the buttons as soon as it starts to reboot itself, but it doesn't start the bootloader
Click to expand...
Click to collapse
You should let go only of power button and hold vol.down button (at least for me)
If your PC finds hardware - can you do fastboot devices to check whether it is actually recognized properly?
And last thing - which method you used to load recovery (and were you on ICS\JB)? You were rooted and used automated methods or you unlocked bootloader and wanted to root afterwards (manually through fastboot)?
Divina Angelus said:
Just of curiosity - which button you used to select recovery - power button or vol.up button?
You should let go only of power button and hold vol.down button (at least for me)
If your PC finds hardware - can you do fastboot devices to check whether it is actually recognized properly?
And last thing - which method you used to load recovery (and were you on ICS\JB)? You were rooted and used automated methods or you unlocked bootloader and wanted to root afterwards (manually through fastboot)?
Click to expand...
Click to collapse
You are a GENIUS!!! A LIFE SAVER!!! I can't begin to tell you how grateful I am. BOTH of your points fixed the phone.
I could never get into recovery becuase I was pressing the power button. I could never get into fastboot becuase I was holding both the power and volume down button.
So, for anyone using a RAZR I... please note the following SIMPLE things:
1) In the bootloader menu, the power button does NOT select the option. The VOL UP button selects the option
2) To boot into BOOTLOADER : Hold both power and vol down buttons until the phone restarts, and then RELEASE the power button, while still HOLDING the volume down button! It will then load the bootloader.
Again, THANKS so so much for reviving my phone for me. I was going crazy without a phone!
alkit said:
You are a GENIUS!!! A LIFE SAVER!!! I can't begin to tell you how grateful I am. BOTH of your points fixed the phone.
I could never get into recovery becuase I was pressing the power button. I could never get into fastboot becuase I was holding both the power and volume down button.
So, for anyone using a RAZR I... please note the following SIMPLE things:
1) In the fastboot menu, the power button does NOT select the option. The VOL UP button selects the option
2) To boot into BOOTLOADER : Hold both power and vol down buttons until the phone restarts, and then RELEASE the power button, while still holding the volume down button! It will then load the bootloader.
Again, THANKS so so much for reviving my phone for me. I was going crazy without a phone!
Click to expand...
Click to collapse
I was going through everything you've faced yesterday. So yeah, glad I was of help to someone else as well)
This has never happened to me before but don't stress one bit because nothing ever permanently bad comes from this. You can forget about it being destroyed. These aren't iPhones, haha. You can get it going again pretty easy I hear. Just don't stress because there is no point and you WILL get help. Just listen to what these experienced dudes are saying and you should be back on track. Good luck!
- - - - - - - - - -
UPDATE: Nice! Glad to see you got the help you needed and everything's back on track!
Nice that it is solved. I gave u the solution on my first post, but nice that someone els did a better job in explaining it
There is almost no possibilities to brick your device if u only flash things like the boot, system, recovery or data partition. They can he solved very easy. If u flash the other partitions like the radio u can get a problem.
Sent from my XT890 using xda app-developers app
Hazou said:
Nice that it is solved. I gave u the solution on my first post, but nice that someone els did a better job in explaining it
There is almost no possibilities to brick your device if u only flash things like the boot, system, recovery or data partition. They can he solved very easy. If u flash the other partitions like the radio u can get a problem.
Sent from my XT890 using xda app-developers app
Click to expand...
Click to collapse
You are 100% right. I just re-read your post, and noticed that you did mention those 2 points. I must've just read over them really quickly and didn't pay attention to the details of which buttons to press. :angel:
Thanks a ton for your help! Really appreciate it! :highfive: