Wifi/GPS problem after motherboard replacement - Nexus One Q&A, Help & Troubleshooting

Hi guys.
Yesterday i replaced motherboard on my N1, previous motherboard was broken, after replacement everything is work fine, except wi/fi and gps. My wi-fi module catches the signal slightly, like w/o antenna, gps have not been able to get to work now.
My question is, where is wi fi module exactly? I try to made some photos of my donor phone with pars in some days, but maybe there is some document or photos with this parts, that I will be able to analyze on my phone

If I remember right, the wifi antenna is hooked up near the upper left side of the phone (screen facing down). Verify that is fully connected.

Check out ifix it they have a tear down of the nexus one so you can see where everything is.

Thx for your advices, i'll try to check antenna

Related

[Q] No Signal at all after replace the housing

After the replacing of my X1's housing with the new one in the SE Service center I went home gladly with my new X1 housing. I noticed there's an error in signal in my X1 when I was checking my phone at the SE center.. But I thought it was maybe due to poor reception thus I neglected it. (the officer in the SESC say so)
Now I know that there's some new problem arise.. Any idea what might cause this error? the phone can read the Sim card but there is no signal (no connection, no call or no data can be made). i try to check the antenna module, but it seem to be OK (i did not see any problem on it).
the next day i came to the SE center, they said it might be something wrong with the software (since i am used using cooked rom) how come it can make any different while i'm using it before i replace the housing. and they have to take it into the HQ. and guess what, it may take another 6-7 week... WTF
is there anyone having the same problem with me?
Well if you have the tools, you can try openingu p the bottom cover, that little rubber thing where it has the mini sony ericsson logo. Open that rubber up, and you should see a mini screw in the middle, open that up take it out, maybe just give it a quick clean, fit it back properly, and make sure everything is tight and see how that works out.
I've seen/heard a few people having such issue when taking the housing off, and not placing that radio/reception thingy back properly, therefore causing issues with reception.
briian_ said:
Well if you have the tools, you can try openingu p the bottom cover, that little rubber thing where it has the mini sony ericsson logo. Open that rubber up, and you should see a mini screw in the middle, open that up take it out, maybe just give it a quick clean, fit it back properly, and make sure everything is tight and see how that works out.
I've seen/heard a few people having such issue when taking the housing off, and not placing that radio/reception thingy back properly, therefore causing issues with reception.
Click to expand...
Click to collapse
I did it twice, just to make it sure that everything was on their place, also try to flash the ROM, The Radio but still remain the same....
any other suggestion or idea what should I do?
Same problem!
I had disassembled my phone by myself twice; the first time it worked perfectly, the second, unfortunately, it didn't!
I bought a new antenna module for U.S. $10, installed it myself (warranty ended three months ago), walked out of the service centre and voila; I had reception and managed to make a few calls. However, on the way back home, all calls placed while driving dropped every 5km, which means the hand-over between cell towers was failing. The moment I walked home it was dead; no reception whatsoever indoors.
Now the way I see it, this could be due to one of the following two reasons: either the RF power amp failed, which means that most probably the phone needs a new main board (too expensive, not worth it) or something went wrong during the assembly, like the smearing of a sensitive part by skin oil (thus causing a short circuit) or failure to position a connector or multiple ones to connect properly to their respective terminals/connection points.
Upon further investigation, I noticed that my phone wasn't properly grounded; whenever I connected it to a computer to sync using ActivSync or in disk drive mode, I got a small electrical shock (painful though) whenever I touched the phone. This, however, doesn't occur at all when I connect the phone to the wall charger. I disabled USB charging since day 1 of owning my X1i
I believe that the battery cover acts as a ground for the phone electronics; it touches four golden connectors which in turn touch the mini USB port, the GPS/Wi-Fi/Bluetooth antenna, a point on the main board half an inch away from where the loudspeaker is, and the metallic cover placed over the phone RF chips. Failure to ground the phone properly can result in either damaging any of these chips, building up a static charge that affects the antenna performance, or an open-circuit condition for one of the many systems on board.
Since my phone is fully working as a PPC now (PPC functions, Panels, Keyboard, Camera, GPS, Wi-Fi, Bluetooth, etc...) and since I get reception outdoors, and since I have a brand new antenna module, I am guessing that either the RF amplifier is dead, or the housing is ****ed up beyond repair (i.e. it can't be aligned perfectly to get perfect contact on all said points) that it's either shorting a connection, or opening one that is vital for the cellular radio to function properly.
So what to do? Well I forced my phone to do two things:
1. Settings > Phone > Band
- Network type: I chose GSM instead of Auto, as we don't have consumer CDMA in Egypt
- GSM/UMTS Band: I chose the correct band for my provider instead of Auto.
2. Settings > Connections > Advanced Network > Disabled HSDAP
What happened? It worked indoors for a minute, and then stopped working again! Frustrating! So what did I do? I ordered a completely new housing off CNN and will attempt to rebuild the damned thing.
I will update you if I find out anything or reach any results with this phone that I love so much and hate more than anything I have ever hated in my life...
More info!
- During the drive mentioned above, the phone was switching between H, E and G, which means that all three RF chips are, or all components of the whole RF chip if it's one responsible, are working. At one point I got 4 bars of H and call quality was perfect between hand-over failures.
- Before disassembling my phone for the second time, people were complaining about high-pitched static; it can blamed over the mic, the RF (antenna or chip) or humidity levels (which are currently as high as 85%) affecting cellular communication channels.
- Flashing the firmware (R3A Generic UK) and hard-reseting didn't solve the problem.
More Info!
- The battery cover isn't the phone's ground; it's grounded by being connected to four ground points: the mini USB port metallic frame, the GPS/Wi-Fi/Bluetooth antenna ground, a ground point on the main board and the metallic cover over the sensitive RF chips.
- This is definitely an assembly problem. The reception is great outdoors switching between all bands and speeds. On my drive to work today it worked getting G, E, 3G and H all in 4 bars. The signal, however, is completely unstable, jumping from one speed to another. I am more inclinded now to believe that a new housing will fix this problem. Your housing was probably handled poorly at the service centre, which in turn caused this problem.
My advice is to shake them a little bit and see what they will do.
A New Housing didn't fix it!
I purchased a new housing from CNN. It came in good condition. The phone looks brand new now but still no signal. I am sending it in for service. I guess I blew up my Power Amplifiers...
Good luck mate!
melaskalany said:
I purchased a new housing from CNN. It came in good condition. The phone looks brand new now but still no signal. I am sending it in for service. I guess I blew up my Power Amplifiers...
Good luck mate!
Click to expand...
Click to collapse
Same problem haa...
I still waiting for a good news from the service center... I have been waiting for a month..
I wish You a good luck too...
I'm having the same problem. I opened up my phone a few days ago to clean the keyboard. The bottom row wasn't working correctly. Unfortunately after I closed it up again, it wouldn't get any reception (and the keyboard's bottom row was still not working correctly).
So I figured it was the antenna and tried to reposition it. I even removed the rubber layer as described here: http://blog.whitesites.com/How-to-Increase-Reception-on-Sony-Xperia-X1__633958291637656250_blog.htm
Outside I get ok reception, but it's far from stable, inside I get none. And even if I get reception inside, once I pick up the phone, signal drops. So I thought about grounding as well, problem is I even tried rubber gloves and that doesn't solve the problem. I'm afraid replacing the antenna's won't help here and my xperia is dead. Anyone has any other ideas?
Been there too!
I tried the same solution the blog explained. However, I ended up not getting any signal at all. It's only after I purchased a new cellular antenna+buzzer module that the phone started getting an unstable signal outdoors.
Did you notice any small pieces falling off the main board or the housing? It's either a hardware failure or a simple short/open circuit situation that can be fixed in a blink of an eye!
Question
Is there any possible way, hardware or software, to test whether all chips on the main board function properly? I tried the diagnosis tool available here but it doesn't check the chips one by one.
Service Centre
I took my phone to the service centre 6 hours ago. With the new housing on, and new screws that I scored from a secret source of mine, they deemed the phone untouched and serviceable; i.e. it passed for a phone that hasn't been tampered with!
They told me to call back in four days. I will keep you guys updated. Cheers!
I wonder if that'll fix it So to summarize you have:
- new housing
- new screws
- new vibramotor
- new antenna
And those things twice and that fixed it maybe?
I guess it's time for a new phone for me
Vibramotor?
Who said anything about changing the vibration motor? I installed a new antenna + buzzer module; i.e. a new cellular antenna and a new loud speaker (external speaker). The loud speaker is housed within the antenna module. My bad, maybe that part was vague because I never explained it enough.
And yes, it has a brand new housing too. I only installed the lower part though, as the upper part is just fine. Maybe they will fix it man; maybe they won’t I really don't know. I do hope they will fix it though.
I am currently using a backup cheap Nokia and ordered the Sony Ericsson Aspen. If they ever fix my X1 then I can change seamlessly between both phones. If not, then I will just use my X1 as a media/GPS device in my car and an Internet device over Wi-Fi.
Lucky you..... if they can fix yours in a few day... since mine has been in the service centre more than a month, without any news...
they said to me that it will take about 6 week...
What a joke!
The phone remained at the service centre for a week. They called me yesterday, and told me that the phone was fixed and that the total cost was EGP 100 (~U.S. $18). I went over and as soon as I held the phone in my hand to test it, it lost the cellular signal. When placed on the counter, the phone had a constant E signal.
I asked to speak to the manager, who told me that they just reflashed the phone with the latest firmware (Generic UK R3A, which I already had installed). Oh, and before that, he said he was sorry but the phone had a hardware problem and that they don't fix hardware; they only flash firmwares and if that doesn't fix the phone, then the user is pretty much on his own! I refused to receive the phone, so he gave me a refund for my money and promised to have its hardware checked and get back to me in 24 hours!
What a joke, what an f'ing joke! I already regret ordering the Aspen that is due to arrive next week with a friend of mine returning from Paris...
melaskalany said:
The phone remained at the service centre for a week. They called me yesterday, and told me that the phone was fixed and that the total cost was EGP 100 (~U.S. $18). I went over and as soon as I held the phone in my hand to test it, it lost the cellular signal. When placed on the counter, the phone had a constant E signal.
I asked to speak to the manager, who told me that they just reflashed the phone with the latest firmware (Generic UK R3A, which I already had installed). Oh, and before that, he said he was sorry but the phone had a hardware problem and that they don't fix hardware; they only flash firmwares and if that doesn't fix the phone, then the user is pretty much on his own! I refused to receive the phone, so he gave me a refund for my money and promised to have its hardware checked and get back to me in 24 hours!
What a joke, what an f'ing joke! I already regret ordering the Aspen that is due to arrive next week with a friend of mine returning from Paris...
Click to expand...
Click to collapse
OMG...
I do hope that you will get the good news next...
Bad News!
Deep breath... Ok!
Here is the deal: the service centre officially announced that the fault lies within the Mainboard; i.e. my guess that the Radio Frequency (RF) Power Amplifier Chip is toast was correct. They want to charge 90% of the phone's original retail price (which was EGP 4000 = U.S. $700) for a new Mainboard. I replied that that was impossible. They will contact SE's HQ and get back to me on Saturday to see if they can offer any other alternatives.
I guess that is the end of my ride with the X1. I will sorely miss it; it was a great phone while it lasted. Let's hope that the Aspen won't die on me in a year as well...

[Help] No Satellite GPS after LCD repair

I changed my HD7 LCD+Digitizer and everything is working fine except the GPS that now only works in A-GPS. Is there any document showing the fisical location of the gps chip on the board, or anyone can point me the location so i can check for any damage or loose connectors? Thanks.
I have already faced that issue...
Having the back of your hd7 in front of you, and the crucial screwdriver, you will find two cables on the right side, both connected on the same level on both side of a circuited board, one of them was disconnected and when I fixed it my gps was working perfectly again. Good luck!!
Thanks!!
NebZoNe said:
I have already faced that issue...
Having the back of your hd7 in front of you, and the crucial screwdriver, you will find two cables on the right side, both connected on the same level on both side of a circuited board, one of them was disconnected and when I fixed it my gps was working perfectly again. Good luck!!
Click to expand...
Click to collapse
Found it, its the short black cable on the right side, I wasnt able to see it because one of the connectors is under the board as you said, thanks mate!!

[Q] Replaced microphone not working

I've recently replaced the bezel on my phone and in the process broke the ribbon between the two hardware buttons. I ordered a new one and swapped them over with what I thought was no problem. The keypad note works but now the microphone has stopped working entirely. Could this be a software issue (I do doubt this) as I'm on a stable version of CM10? All the connections are linked up and everything looks fine. This one has me completely baffled
open it up again and check the antenna cable again. Maybe it isn't inserted correctly?
That's a good point. I accidentally crushed the antenna cable but wasn't aware that it was relevant when considering the microphone. The rest of the phone works fine including the mobile signal. May have to link up my old mic just to check this
Aargh! It turns out that the old mic is still working so the new one appears to be the issue. Hmmm, wonder what gets a better resale value a phone with no working buttons or one with no working mic *sigh*
well I changed once front bezel from SGS1, too. Still have the old one. Maybe just buy a new parts? I think those don't cost a lot. Whole front bezel cost about ~100e.
I think after this poor attempt to repair the phone I'm gonna put the device up for sale

No Audio after screen replacement

Hi,
I really need your help as I have no idea what to do.
After 1 month of using MI5 Pro Ceramic black I have broke my phone,First the touch worked and there was only vertical lines on the lcd in the spot of the shatter so I could operate but due to my stupidity and of force touching the broken glass these vertical lines started to cover all the screen (Everything worked well on the phone..Sound,Camera and etc..)
So I ordered from Aliexpress LCD + Touch screen for about 70$ (Included DHL Express shipment)
When I got the screen I started to disassamble the phone.. Got everything out,Took out the broken screen and pasted the new screen on the frame (Must say all these aliexpress screens are really bad,0% protection on the screen,Not sure about the LCD quality yet but glass is horrible..Started to scratch even before I used it)
Anyways to our point..
Started to assamble back everything.. Powered on the phone and Yay! Phone is working but...
No Sound,Firstly I checked settings and everything..Ran CIT test and everything that belongs to audio giving force close..
Calibrate Speaker PA test results : State-Get impedance failed!,Speaker Vendor-None
Vibration- FAIL no short and no long
Main mic speaker Feedback,Simulation call test,Front mic speaker feedback test,Top mic speaker feedback test,
everything when I enter it giving FC with that details :
"IlegalStateException:Unable to retrieve AudioRecord pointer for SetParameters() blablala...
Headphone mic feedback test (Called on an uninitialized AudioRecord)
So in short..
No Speaker,No Mic,No headphone Mic..
Now my question is what I need to do from now.. Its not firmware/software problem for sure as before I disassambled the phone everything worked well..
My first guess was the problem is on the Sub PCB but then I asked my self..If the USB-C is working and WiFI antenna giving full signal it means the Sub PCB works so what the hell is the problem? I really hope its not something in the PCB it self as it means throw everything to garbage.. ;<
Hope to hear suggests..
I thought to order the MI5 32GB Black version take out the Main PCB put the Pro Main PCB and put also the ceramic back cover but that I would do only if I know that the problem is from the sub PCB but if Headphone mic doesnt work (Which the Main PCB take care of) then its probably in the Main PCB??
Please help!
you didnt damage the pins on the press connector? is the press connector on the ribbon cable flush / fully inserted ? Are you sure you didnt kink the ribbon cable?
I haven't pulled a mi5 apart, but can only assume its like every other phone i have.
leighaus said:
you didnt damage the pins on the press connector? is the press connector on the ribbon cable flush / fully inserted ? Are you sure you didnt kink the ribbon cable?
I haven't pulled a mi5 apart, but can only assume its like every other phone i have.
Click to expand...
Click to collapse
The problem is that far as I understood of how the mi5 built and from how I saw it looks like..The Speaker located in the Sub PCB cover,Vibrate connected to subPCB,And all the SubPCB connected with the cable to the main PCB and I checked it connected good and no any damaged pins from what I was able to see..If there was damaged pins then the phone wont get charged as the USB-C wont be connected as it located in the SubPCB however it does work.. So I really have no idea what cause it..
Also the Headphone mic doesnt work in the tests..Anything related to Audio giving that FC with "AudioRecord" error..
I really must to know what causing it so I will know what to do ;<
Little update,
Just connected a bluetooth speaker,No any sound nothing..
Hi everyone! My MI5 has the same problems, no sound, mic, vibration, led buttons light, plugin earphones without notification's icon, can not play music, video offline and online video (Youtube, Facebook, live stream ..). It was happened when i replaced brooken screen. The first time when I turn on, evetything ok, I can play music through speaker, but now everything has gone..! Plz tell me how to slove this problem! Sorry for my poor E!
Hi, I ended up on buying the phone again... It's impossible to fix that problem as probably you did what I did and didn't place the motherboard correctly so a little bent probably happened and that cause to the problem.
edoroom said:
Hi, I ended up on buying the phone again... It's impossible to fix that problem as probably you did what I did and didn't place the motherboard correctly so a little bent probably happened and that cause to the problem.
Click to expand...
Click to collapse
Hi there! Care to elaborate a little more? I have also the same problem. I was replacing the rear camera module while the module I had received was broken to begin with. I hadn't really figured this out initially and I tried several times to attach it and test it, perhaps move the flex and retest, and at some I remember I found out the vibration was not there, but didn't pay attention to it as everything was open, until I found out the camera module was faulty in the end, and subsequently discovered also the whole issue with sound/vibration/key backlight etc. Instead of buying a new device, I was thinking to try and fix it, but still I'm a bit unsure about what the problem really was. From what I could figure, I didn't do anything different this particular time the audio/vibration didn't work, with respect to the previous times I attached and detached the motherboard. But is it definitely the board itself and not its flex connecting it to the sub-pcb? Could it be the sub-pcb itself or even both this and the board? In case I buy a new board (perhaps together with a sub-pcb just in case) to replace it which part should I watch out for, not to damage it again. Sorry for the many questions but you seem to be the only source of info for this specific problem.
deusxx said:
Hi there! Care to elaborate a little more? I have also the same problem. I was replacing the rear camera module while the module I had received was broken to begin with. I hadn't really figured this out initially and I tried several times to attach it and test it, perhaps move the flex and retest, and at some I remember I found out the vibration was not there, but didn't pay attention to it as everything was open, until I found out the camera module was faulty in the end, and subsequently discovered also the whole issue with sound/vibration/key backlight etc. Instead of buying a new device, I was thinking to try and fix it, but still I'm a bit unsure about what the problem really was. From what I could figure, I didn't do anything different this particular time the audio/vibration didn't work, with respect to the previous times I attached and detached the motherboard. But is it definitely the board itself and not its flex connecting it to the sub-pcb? Could it be the sub-pcb itself or even both this and the board? In case I buy a new board (perhaps together with a sub-pcb just in case) to replace it which part should I watch out for, not to damage it again. Sorry for the many questions but you seem to be the only source of info for this specific problem.
Click to expand...
Click to collapse
Hi sorry for late answer,I barley visit xda these times..
After I bought the MI5 again this time in the 64gb version I tested the old 128gb motherboard (The main one) and still same problem with Vibration/Sound (While all sensors work camera too)
Which means its not the sub-pcb problem,Its the main motherboard for sure,Now what cause it?
In my opinion when I pulled of the motherboard to put it on the new screen I insert it in a bad way which made it bent a little and probably the place I bent is where the audio and all the stuff goes on..
I'm pretty sure we cant really do something about that problem as problem related to motherboard it self are usually not fixable,But if you find something I will glad to get a feedback to test on my own bad motherboard so maybe I can back to the 128gb version ;| but I doubt it..
edoroom said:
Hi sorry for late answer,I barley visit xda these times..
After I bought the MI5 again this time in the 64gb version I tested the old 128gb motherboard (The main one) and still same problem with Vibration/Sound (While all sensors work camera too)
Which means its not the sub-pcb problem,Its the main motherboard for sure,Now what cause it?
In my opinion when I pulled of the motherboard to put it on the new screen I insert it in a bad way which made it bent a little and probably the place I bent is where the audio and all the stuff goes on..
I'm pretty sure we cant really do something about that problem as problem related to motherboard it self are usually not fixable,But if you find something I will glad to get a feedback to test on my own bad motherboard so maybe I can back to the 128gb version ;| but I doubt it..
Click to expand...
Click to collapse
Many thanks for the response! It sheds a little light indeed. I also ordered another phone to replace it as the cost of the motherboard seems to be equal approximately close to a new device. I'm with you, in the same view, I also once placed the motherboard quickly in the chassis without the screw that holds it together, in one of the 50 or so attempts to try and make the camera sensor I was replacing, visible to the OS, and this looseness was the unfortunate one perhaps (?). I too don't expect the sound to work again. I just wanted to double check the issue was not with the sub-pcb, which I did thanks to you. For sure I have no hopes for the mainboard to work again, but still, what keeps me from being certain it is actually the sound card that is the problem, is a very similar case I saw In a foreign forum, and also clues from my device which support the argument that the mainboard might have entered in a kind of diagnostic boot state due to a hardware fault that was apparent, where either some components are not initialized during boot, or their HW resources are taken over from the diag. ports and irqs that are enabled, in which case the issue can perhaps be fixed. For sure whenever I find a good deal on a new motherboard I will replace it, to keep it as a secondary phone, as I liked it quite a bit, but It would be interesting to see if this hypothesis holds or not. Anyway thanks again for the response!
Hi,
I've bought used mi5 with broken screen. After LCD replacement I've found that that phone has problem with sound. Exactly the same as in this thread - no sound, mic, vibration, led buttons light, plugin earphones without notification's icon, can't play music, video offline and online video (Youtube).
Someone already did LCD replacement on this phone and probably done something.
But what I discovered on this phone that problem start when battery charge aprox more then 60%.
I did flash one year old ROM via fastboot ( just to verify if it not the ROM problem) and after that everything was fine ( battery level 50%).
I did hardware test - passed 100% fine.
But when I did charge till 100% the problem come back.
That's really interesting finding... Can you tell me the same steps you did like which rom you flashed and all of that? I will check it with my dead phone maybe if I will have the same thing like you we can point on something...
mi5 lcd replaced touch not working
I bought a mi5 mobile in singapore. My display was damaged. I changed many display in india (checked in many shop). only work display (lcd). Touch not respose. please some one give solution. thank you
have same problem with op
my phone get damaged by water so im rush turn it off and open everything then go to dry it... and problem with speaker etc doesnt work just like op please help i really doesnt have money to buy new phone this month
Exactly same problem with me, just replaced the rear camera and the problem occurs
No sound, no vibration, nav led not working at all, playing video not working
Even playing sound via bluetooth speaker not working too
I believe there is something wrong with the mainboard
can anyone point out which part of the mainboard responsible for the lower board?
The lower board works well though, I tested it using other mainboard
codearm2 said:
Exactly same problem with me, just replaced the rear camera and the problem occurs
No sound, no vibration, nav led not working at all, playing video not working
Even playing sound via bluetooth speaker not working too
I believe there is something wrong with the mainboard
can anyone point out which part of the mainboard responsible for the lower board?
The lower board works well though, I tested it using other mainboard
Click to expand...
Click to collapse
For me the problem was that after the screen replacement (It may also apply to you after you replaced the rear camera..)
When I put back he main motherboard it wasnt sat properly,I put it beneath a small plastic holder and when I closed everything and screw and all..Problem appeared and when I rechecked motherboard I found out it got bent in the right down side and that's probably what killed all the sensors,sound and everything..
Of course that what happend to me..There is plenty of other reasons that may cause to what you experience..
edoroom said:
For me the problem was that after the screen replacement (It may also apply to you after you replaced the rear camera..)
When I put back he main motherboard it wasnt sat properly,I put it beneath a small plastic holder and when I closed everything and screw and all..Problem appeared and when I rechecked motherboard I found out it got bent in the right down side and that's probably what killed all the sensors,sound and everything..
Of course that what happend to me..There is plenty of other reasons that may cause to what you experience..
Click to expand...
Click to collapse
I believe the chip or something similar, that control the sensor, led, vibration etc, was broken because we put it the wrong way
now we need to find which chip it is and replace it
which part of the right down? near the signal cable?
codearm2 said:
I believe the chip or something similar, that control the sensor, led, vibration etc, was broken because we put it the wrong way
now we need to find which chip it is and replace it
which part of the right down? near the signal cable?
Click to expand...
Click to collapse
If you just checked and saw you put it wrong as I did,On the little plastic which made a little bent then I guess you lost..I would just buy new motherboard on aliexpress or just give up and buy a new phone..
As you cant really know (I mean from our side..) if its a chip related there or if its the bent it self which made problem on the connection on the board it self..
And yes I was speaking about the right side near the signal cable where you need to install the motherboard from that side where there is a little plastic like holding the motherboard..When I did the reinstall by not checking I put the motherboard on that plastic and after I closed everything and all screws got back I discovered that problem..
edoroom said:
If you just checked and saw you put it wrong as I did,On the little plastic which made a little bent then I guess you lost..I would just buy new motherboard on aliexpress or just give up and buy a new phone..
As you cant really know (I mean from our side..) if its a chip related there or if its the bent it self which made problem on the connection on the board it self..
And yes I was speaking about the right side near the signal cable where you need to install the motherboard from that side where there is a little plastic like holding the motherboard..When I did the reinstall by not checking I put the motherboard on that plastic and after I closed everything and all screws got back I discovered that problem..
Click to expand...
Click to collapse
yeah, it means it's the same mistake as mine, that little metal thing that hold the motherboard, I forgot to eject the sim card tray and when I pull my main board it was stuck, got a little bent from there
Just wonder if anyone have the schematic for mi5 mainboard, since I'm curious and want to find a way to repair it
Not because I'm in despair of needing a phone, this MI5 is my secondary phone
Just because of the curiousity, that's all
edi--
found the schematic here
https://data.dendik.id/Data/Schematic/Xiaomi/Mi5_SM.rar
now on the journey to repair this stupid mistake, lol
any help from someone who are an expert in this thing will be really appreaciated
codearm2 said:
yeah, it means it's the same mistake as mine, that little metal thing that hold the motherboard, I forgot to eject the sim card tray and when I pull my main board it was stuck, got a little bent from there
Just wonder if anyone have the schematic for mi5 mainboard, since I'm curious and want to find a way to repair it
Not because I'm in despair of needing a phone, this MI5 is my secondary phone
Just because of the curiousity, that's all
edi--
found the schematic here
https://data.dendik.id/Data/Schematic/Xiaomi/Mi5_SM.rar
now on the journey to repair this stupid mistake, lol
any help from someone who are an expert in this thing will be really appreaciated
Click to expand...
Click to collapse
ok bruh im already do some fking around and do ic audio replacement but no hope its still broke even my repair guy who are ex xiaomi worker are give up the problem is looks like from cpu its self but there was something interesting if u try download device info hw app in google play there was warning that the device cant read sys or something cuz it was blocked and when u look at audio chipset its was gone
feel2death said:
ok bruh im already do some fking around and do ic audio replacement but no hope its still broke even my repair guy who are ex xiaomi worker are give up the problem is looks like from cpu its self but there was something interesting if u try download device info hw app in google play there was warning that the device cant read sys or something cuz it was blocked and when u look at audio chipset its was gone
Click to expand...
Click to collapse
Yeah, tried it before, and the audio chip is gone
Perhaps something wrong with the audio chip, will try to replace the IC tomorrow

Found a Midnight OnePlus 3T on Craigslist for $10! The issues are...

Hey guys,
So I've personally owned this device before and sold it, however, luckily I was looking about on Craigslist and managed to run into a post where this lady was selling her Midnight 128gb OP3T for $10 due to the wifi not working. The phone is literally spanking new and the only thing I can think of is water damage. She said the wifi suddenly stopped working and spoke with OnePlus Tech support and wasn't going to pay $275 to fix it so she just wanted it gone. So I figured whats there to lose, right? I went home performed a factory reset on the phone and the wifi actually was working. Then I realized it's intermittently working. I found that out because after sometime it suddenly disables itself and I have to sleep the device for like two minutes and it'll kick back on. The proximity sensor is also dead too. I did the *#808# to test the sensor and nothing is generated. These are the only real issues this phone has. The loud speaker also sounds a bit off... I'm sure I could easily replace that too.. It could just be me. I've posted the snapshot of the proximity sensor test. The wifi was currently working when I took that snapshot and like I said it's a hit or miss.
I haven't gotten into the device just yet, however, I'm planning to check the water damage sticker once I do as that is my suspicion. I'm waiting on my tool set I ordered on Amazon at the moment. My question is, do you think replacing the wifi antenna cable will fix the wifi connectivity issue? The phone is currently on 8.0 Oreo and I haven't tried performing a complete reset/restore so I'm not sure that could be a fix. Also the phone doesn't get too hot and usually with water damaged devices the phone typically overheats pretty fast due to corrosion. I guess I'll find out after I open the device, but for now do you guys have any other suggestions? I've heard of the whole IPv6 intermittent wifi issues and can assure I have IPv6 disabled.
Thanks for taking the time to read my question!
The WIFI thing isn't something I think you can just replace, I think you would just need to replace the board right?
Yes, you would need to replace the mainboard of the phone. However 10$ is quite cheap for a spare screen and midnight black metal casing. Just find a cheap 3T with broken screen and switch mainboard with that one and you have a working phone. [emoji16]
Before doing that, check the phone's board and look for corrosion. If you find any, try cleaning it up gently, with some alcohol and if you manage to get it all cleaned up, try testing it again to see if it solves the problem.
If you get the schematic for this device and have a boardview program you could find the wifi circuitry..... it is more than likely some short to ground due to the fact that you are feeling heat.... due to liquid damage or not. Sometimes changing a small component can fix the issue but you need a microscope, heat gun, solder pencil, etc......

Categories

Resources