Related
Ok, not sure if anyone got the same problem as mine, but here is my problem:
I have a Diamond using AZTOR v7 Rom, radio vBS14 if that matters and Sony Ericsson DS205 as my headset. I start my bluetooth on my diamond and can pair up with the DS205 without any problem. I can also listen to music without lag and sound is also crystal and solid.
When there is a call kicks in, I can answer the call by pressing a button on my DS205..... However, the problem comes when I end my call, the headset will be disconnected afterward and I have to manually press a button on the DS205 to make it reconnect. Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
I don't have this problem, but i have another problem, when i use the orignal rom, i can use my headset(jabra bt3030) in my diamond and it will automatically connect to use hands free and wireless stereo mode when i turn on bluetooth, so when i change to use swift 7.5 full rom, i have to resetting the bluetooth in diamond everytime when i close bluetooth
I can only get wireless stereo for my Plantronics Bluetooth Stereo headset. Any ideas why I can't get hands-free. Radio issue?
It was possible with some earlier ROM, but I can't remember which... (yes, I'm a flashing addict).
I'm having the same exact problem & it's annoying as hell. At this point, I can't get the bluetooth function on the phone to activate at all. I use the same bluetooth on another phone with no problems whatsoever, so I know it's the phone. I'm running the original rom.....not a flasher.
Have you tried Jetware?
Sorry, just installing this doesn't change anything. Still no hands-free.
Is there a specific option you want us to set?
shinji_lee said:
Have you tried Jetware?
Click to expand...
Click to collapse
lit2fly said:
... Each time when I make a call or when I receive a call the headset will be disconnected.
Luckily (or not), I found a workaround: Whenever I pair up my headset, I need to go to Setting -> Bluetooth -> and "Refresh" the services that I want to enable on the DS205 headset. That involves un-checking the services enabled (including "Wireless Stereo" and "Hands Free") and re-checking the services again. After I have done this "resetting", the disconnection problem I described above will be gone.....
Each time I restart the phone or have the bluetooh disabled on the phone, I need to go through that manual procedure again to make my headset work perfectly.
As you can imagine, that is quite annoying.......does anyone have the same problem as me?
Click to expand...
Click to collapse
Yes - I have a very similar problem with my jabra SP700. The Diamond 'forgets' the wireless bluetooth mode every time I disconnect the two devices (although the Stereo Bluetooth icon is still showing in the status bar).
For a short while I was having to re-pair the devices every time I got in the car - until I found the same workaround as you.
There must be a proper solution???
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
juanfervs said:
Hello, I had that problem in my HTC Diamond with Pioneer DEH-700bt and my jabra 3030 and she solves when changing in the registry the key to it that identifies the device in pocketpc HKLM/Software/Microsoft/Bluetooth/Sys the key "COD" and I introduced the value decimal 5898764 that identifies the device in smartphone
luck
Click to expand...
Click to collapse
I have this value in COD key but I have the problem anyway.
Any solution to this annoying problem?
i use my diamond with my bluetooth handsfree kit in the car, it is classed on the phone as a headset though. the sound is ok, a bit echoey but ok. but the microphone doesnt seem to pick up my voice, i have to really shout for people to hear me, on my old Xda Orbit it worked fine. any ideas?
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Edris said:
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Click to expand...
Click to collapse
I have the same problem with my SP700 and my Tritton BT stereo headset.Phone calls work almost all the time through the SP700 speaker, but playing music or through the FM radio seems to be a problem. I can get them to pair up sometimes by only checking the Wireless Stereo box. It works for a few times, but then I have to delete and re-pair again.
I've searched for all over for answers, but nothing seems to be a permanent fix. It's very frustrating to use my devices for anything else but phone calls.
Just to add a bit of info, I do not have any problems with my old Motorola HS820. Of course, I'm not using SP700.
Hope that helps your troubleshooting.
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Possible solution
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Edris said:
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Click to expand...
Click to collapse
Thanks! Nice App! Tried it with my Tritton BT stereo headset and it works! Had to install to my device instead of Storage card, then had to delete and re-pair, but it so far I can toggle between on and off Stereo Headphones without any problem. Will try on my SP700 shortly.
I attached the Cab if anyone else wants it.
Thank you!
Works with SP 700!!!!!
Mal Bridgeman said:
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Click to expand...
Click to collapse
When the software loads, follow the instructions, do not install with any of the microsoft wizards that pop up, it will install itself. I couldn't find anything that lists what changes that were made.
SP700 Firmware
FYI,
I too had the same issues and downloaded the sp700 firmware update. I thought the same thing about the drivers, but called Jabra and they told me the firmware update has the drivers embedded in it. When you start the install you cannot plug it in till it tells you to. After you plug it in it installs the drivers. But BEWARE I have not been able to complete the upgrade, it stopped halfway and bricked. I called support and they said there is nothing to do, but luckily I bought it from Costco and they returned it. So being not so bright I tried it again but on a different computer (thinking that there might be a conflict) and it didn't even load and bricked it again. So I returned it yet again. So then I gave up on Jabra support and found A2DP toggle. It works good enough, so I am leaving it at that....
Take Care
David
Tilt WM6.1
andrew-in-woking said:
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Click to expand...
Click to collapse
I have the exact problem that you are having with the new, Hyperdragon IV, ROM.
Is this A2DP Toggle really the only way - I mean what's the difference between pressing a button on my Kaiser to reconnect and pressing the button on the SP700 ??
I have tried using Mortscript as shown http://forum.xda-developers.com/showthread.php?t=382172&highlight=a2dp&page=2 Although I edited the end out because it kills the player after ending a call. This hasn't helped either
I am off to see if the same problems occur with my lady's N96. If not and no good solution can be found for this I may have got her a new present.
Aren't I nice ?!
Found another possible solution, it,s called zoA2DP. So far it works flawlessly between my SP700 & stereo headset without having to toggle anything or change any settings. When you install it, delete your original pairings and add them again, make sure that hands free & wireless stereo are checked in advanced options on you BT settings. I believe this is a registry mod, there are no icons or any noticeable applications running in the backround.
The thread is here
http://forum.xda-developers.com/showthread.php?t=279127
Cab file attached
I can not pair my BT head set i-Tech R35 Clip to my new TD2, i get to the enter password part but they do not pair off. I have put the BT head set in to pairing mode.
Does anyone have any advise to get me paired off.
Thanx and regards
Chris
Pairing BT
there is two places you can pair your topaz with a BT headset.
1) link in comm manager over BT, not the switch part at the far right, but the bar where it says bluetooth. it'll take you to a screen where you can pair a headset.
2) in settings in the conection tab under bluetooth (or comm manager, BT and advanced), which is a multi tab that shows you the deviced paired, connected allow you to be discoverable the ports you created etc...
my point is for headset i have had problems conecting thru the advanced menu (2) but it worked thru the Comm conection, i don't even have to enter the key, it seems like it tryes 1234 0000... so i recommend going to the option 1, and there pairing your headset.
the other thing i noticed is when you pair a device, if you got the wrong key on the first atempt even if you enter the right one after it will not pair, so the solution is pressing back refresh and connect again and then enter the right key.
at least it worked for me
cheers
Timothy
Thanx for your guide, unfortunately it still will not connect. either option 1 or 2. I tried entering the pass code 0000 but it fails to connect and says the pass code was incorrect. If i try the option of no pass code it says it has connected, however the BT headset does not respond with hte usual 5 x flashes of the LED.
I still can not get connected :-(
My phone wouldn't recognize my new Plantronics Discovery 925 headset. I tried pairing with a samsung headset too, it wouldn't recognize that either. But my phone recognizes other phones and works fine. Please help.
bLack_swAN said:
My phone wouldn't recognize my new Plantronics Discovery 925 headset. I tried pairing with a samsung headset too, it wouldn't recognize that either. But my phone recognizes other phones and works fine. Please help.
Click to expand...
Click to collapse
First and foremost, what ROM are you running? Are you on stock? Rooted? What modifications have you made, as those are the most likely culprits.
If the answer to all the above questions (save for stock) are no then I perhaps asking Plantronics or google about your phone/headset might work better as its likely that one or the other is defective.
I bought the phone only a week back and I have not made any changes to it. In fact my friend and I got our phones together. His phone is not recognizing the headset too. But my headset works fine with other phones of any make.
I have and use that specific headset on my Nexus S. And it works and pairs right away. Have you tried resetting the bluetooth before pairing?
Nexus MC said:
I have and use that specific headset on my Nexus S. And it works and pairs right away. Have you tried resetting the bluetooth before pairing?
Click to expand...
Click to collapse
Did you do anything particular before connecting your headset or did it just show up on the devices list?
Resetting the bluetooth as in switching on and off? Yes, I did.
bLack_swAN said:
My phone wouldn't recognize my new Plantronics Discovery 925 headset. I tried pairing with a samsung headset too, it wouldn't recognize that either. But my phone recognizes other phones and works fine. Please help.
Click to expand...
Click to collapse
Got the same, running great. make sure both are in pairing mode...
RinTinTigger said:
Got the same, running great. make sure both are in pairing mode...
Click to expand...
Click to collapse
Sorry, I dont understand. How do i set the headset to pairing mode? Please explain.
Folks, I finally managed to pair my headset with the phone. It is working fine now. Here is what I was doing wrong. I was trying to pair my device with the phone by just switching on the device and scanning for devices on my phone. When I try to scan, the device would not show up on the list.
This is because, the device was not in pairing mode. In the Plantronics Discovery 925, you need to switch off the device, power it on back by holding the power button and keep holding it until it flashes red and blue. This is when the device gets into pairing mode and it shows up on the phone's list. All this has to be done while the phone's bluetooth is ON and it is scanning for devices.
Hope this might help someone. My thanks to all those who cared to reply.
That's great you figured it out.
but here's for future reference:
Plantronics Discovery 925 (Pairing)
Pairing the Plantronics Discovery 925 to Your Cell Phone
1.Put your phone into pairing mode
This can usually be accomplished by going under settings in your menu and selecting Bluetooth. Follow the prompts to "find a new device." If you are having problems, refer to your phone's user guide.
2.Put your Discovery 925 into pairing mode
Start with your headset off. Press and hold the call button until the indicator flashes red and blue.
3.Select the headset in your phone's Bluetooth device menu and enter in universal key
Your phone may or may not ask you to enter in a key code. If it does, the code is always four zeros: 0000
4.You are paired up!
That is a rather ridiculous process, with my motorola I just have to flip the mic boom open and it works.
kenvan19 said:
That is a rather ridiculous process, with my motorola I just have to flip the mic boom open and it works.
Click to expand...
Click to collapse
It's probably straightforward for some brands, not with others. My Jabra BT3030 still needs passcode entry for the initial pairing. After that, just turning it on pairs it with the unit.
kenvan19 said:
That is a rather ridiculous process, with my motorola I just have to flip the mic boom open and it works.
Click to expand...
Click to collapse
Uh what? They're talking about the pairing process, you're talking about the connection process. Every bluetooth device every created in the history of mankind has to go through a pairing process. After the initial pairing, they all connect to each other automatically, your motorola is no different.
Well, how do I do that?
Bluetooth just stopped connecting to my parrot mki kit and there is no way to unpair it from my phone. Short press, long press, it just starts connecting and then time outs. There is an 'i' icon, but can't press it.
Cleaning cache & data for bluetooth app does nothing.
EDIT: installed Bluetooth Pair from play store. Successfully unpaired my parrot kit but now I see it under available devices even though my car is locked and 20km away. Wow, just wow.