Related
Help !!!!!!!!!!!!!!!!!!!!!!!!!!
hmy captivate died after flashing Axura using clockwork
now I can not boot up the phone, unplug the battery for 15 Min and put it back but still the same can not boot up the phone....
please help
You need to figure out a way to get into Download Mode, use ODIN, and flash back to JF6. Once you have JF6 running, you can flash whatever rom you want again.
If you search, you'll see a bunch of posts on the different methods to get to Download Mode.
Goodluck.
Yes, I know if I get download mode I can flash whatever rom, but the problem is that the phone completely dead nothing shown in the screen, I have tried the following
1- try the combination of Vol down + Power
2- try the combination of Vol up + Vol Down + Power
3- try Vol down and then connect USB
4- try Vol down + Vol Up and then connect USB
all these while opening ODIN
also I tried this on both windows 7, and windows XP.
do you have any other suggestions to do.
please help
Still have the problem, need heeeeeeeeeeeeeeeeeeelp please
How did it exactly die? It'd be useful for people who may know a solution. I've heard of JIG a few times.
you get the little home lights on the bottom of the phone to light up at least?
Also.. does the computer recognize the device?
If not and it's completely black screen and you don't even feel it vibrate while booting? Its toast.
But.. try doing the battery/sim card pull - hold down both volume buttons plug in the USB and jam in the batter and see if that works.
Or.. to the ATT warranty center you shall go.
I was flashing Axura rom using clockwork recovery, and after complete the installation and start reboot this back screen comes on, now not booting at all
Odin not recognize the phone, or even the computer does not detect any connected device,
I tried pull the battery, wait for 15 min then connect the USB, hold vol up, down and power keys then put the battery back while holding these three keys nothing happen, the screen still black and the computer not detect it.
I tired all ways but nothing works with me.
Now I think it is complete died, Even I tried the hair dryer trick but nothing works.
some posts talk about JIG
How this JIG works and how to do it?
up for heeeeeeeeeeeeeeeeeelp
hzeid said:
I was flashing Axura rom using clockwork recovery, and after complete the installation and start reboot this back screen comes on, now not booting at all
Odin not recognize the phone, or even the computer does not detect any connected device,
I tried pull the battery, wait for 15 min then connect the USB, hold vol up, down and power keys then put the battery back while holding these three keys nothing happen, the screen still black and the computer not detect it.
I tired all ways but nothing works with me.
Now I think it is complete died, Even I tried the hair dryer trick but nothing works.
some posts talk about JIG
How this JIG works and how to do it?
Click to expand...
Click to collapse
USB Jig will trigger the phone into Download mode.
******Soldering Required******
http://forum.xda-developers.com/showthread.php?t=819551
****Solderless version****
http://forum.xda-developers.com/showthread.php?t=841512
I followed JIG solution, connect resistants of 301K on pin 4,5 on mini usb head, nothing works still black screen, no at&t log nothing
help any new suggestion
try charging the phone for a few hours, if possible try a different battery.
also you may be in download mode with a black screen. i had a bad crash once from too much overclock or a corrupted kernel flash with the manhatten project 1.6ghz kernel. it corrupted the image files for bootup and download mode, my startup screen was garbage and had a black screen for download mode. but download mode still worked. start odin, it may still show device connected.
I did connect the JIG for 10 sec then disconnect it, then connect the phone to the computer while ODIN open, but nothing happen the computer still not detecting the phone, also the screen still black, it does not even any sign of responding except it get heated when connect it to charger.
guys as posted in other thread, will reward 75 US$ for who will help me getting my phone back to life
if you got the phone through at&t, you might as well just go exchange it for a new one. the people there won't be able to determine if you've voided your warranty if they can't boot your phone either.
sorry I did not got the phone from AT&T, I bought it from Ebay so I can not send it back to them
So I was attempting to flash back to stock with Odin (I was using Assonance 5.2). I turned the phone off, then while holding the volume buttons plugged in the USB like normal. Then Odin said added the phone, then I hit start. And it seemed like it was working just fine, then all of a sudden the screen on the phone turned red. Then the status bar on Odin stopped moving completely (stayed for awhile). So I think I made the next big mistake of just disconnecting the USB and taking out the battery. So now the phone won't turn on. So I'm not sure I hard bricked the phone or what? Anyone have any idea? Thanks!
I've plugged the phone into the outlet charger, still nothing happens. This happened like maybe 15 min ago. No action when plugged in the computer or charger. Can't even boot into recovery I don't think. the power button was giving me some trouble earlier today. whenever I was trying to wake the phone up, it seemed to take a few clicks of the power button to wake the phone. This happened only after I flashed Assonance 2.5, so I wanted to flash to an earlier version of the rom. thanks!
What you want to do is get into Download Mode, and flash with Odin One-Click JF6 to get your phone working again..
Have you tried all the various button combos to get into Download Mode? .
If the button combos don't work, you can always try to build/buy a JIG which will force your phone into Download if it's still possible on your phone.
I've tried to get into download mode, but can't seem to do it. I've tried holding the volume up and down button then plugging in the usb (which didn't work). then i tried the taking the battery out, then holding the volume up and down button and power button, then plugging in the usb, then reinserting the battery, then taking my hand off the power button (which didn't work). what is the JIG method?
edit. ok i have no clue wtf just happened, but i am currently in download mode using odin and flashing back to stock.....this is just too weird.....sooo any rom suggestions?
Look in my signature for an example of a JIG.
norcal einstein said:
Look in my signature for an example of a JIG.
Click to expand...
Click to collapse
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
i clicked on the link but it won't let me go the page. below is the message it gave me.
marefin, you do not have permission to access this page. This could be due to one of several reasons:
Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.
marefin said:
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
Click to expand...
Click to collapse
Definitely a great idea having the jig. Nor cal can attest to the late night save that jig provided me.
Sent from my SGH-T959D using XDA App
I have updated the phone to android 2.2.1 and after reboot it appears Samsung's logo, vibrate once, but then it goes to a black screen, vibrating something like this: "bzzz.....bzz-bzz.............bzzz....bzz-bzz...." and so on )
The phone didn't restarted by himself, I had to chose system reboot. There were some red lines, but I don't remember what they were saing, as I did not pay attention to them
The update was made through Kies. The phone was with 2.2 version and was rooted with some app from the market, don't remember which, and is from Orange Romania.
So...what I need to do? Does anyone knows? It's not even my phone, my brother has it, but I'm the one who wanted the update )
L.E.: LagFix was also installed on the phone and I think those errors was from some files which could not be edited or something like that...and please, I'm a little desperate...
CaracalSef said:
I have updated the phone to android 2.2.1 and after reboot it appears Samsung's logo, vibrate once, but then it goes to a black screen, vibrating something like this: "bzzz.....bzz-bzz.............bzzz....bzz-bzz...." and so on )
The phone didn't restarted by himself, I had to chose system reboot. There were some red lines, but I don't remember what they were saing, as I did not pay attention to them
The update was made through Kies. The phone was with 2.2 version and was rooted with some app from the market, don't remember which, and is from Orange Romania.
So...what I need to do? Does anyone knows? It's not even my phone, my brother has it, but I'm the one who wanted the update )
L.E.: LagFix was also installed on the phone and I think those errors was from some files which could not be edited or something like that...and please, I'm a little desperate...
Click to expand...
Click to collapse
Which firmware you had before update? 2.1 Eclair? Most known lagfixes supports for 2.2 froyo
Did you tried your luck with odin?
Thank you androidsl for reply. The phone had froyo 2.2. I don't know where to get odin, this is what I'm searching now. I am downloading I9000XXJPY.rar from samfirmware right now. After I'll get it, I will try to install it with odin, even if I never used it before
And that charghing battery appears on screen when I plug it in USB powered off like it's charging. If I turn it on, no sound as a new hardware detected hears, so it's posible to do anything with odin if my computer doesn't see the phone connected?
Another thing...I can't get the phone in download mode :| It must be the one with 3 buttons problem..damn! What can I do?
CaracalSef said:
Thank you androidsl for reply. The phone had froyo 2.2. I don't know where to get odin, this is what I'm searching now. I am downloading I9000XXJPY.rar from samfirmware right now. After I'll get it, I will try to install it with odin, even if I never used it before
And that charghing battery appears on screen when I plug it in USB powered off like it's charging. If I turn it on, no sound as a new hardware detected hears, so it's posible to do anything with odin if my computer doesn't see the phone connected?
Click to expand...
Click to collapse
My every post have a THANKS button. you can thank me from clicking on that
Did your phone have working 3 button download mode?
Press Volume down key and while holding that press home key. while keep pressing those two, press the power button and hold the all three keys until you saw the boot screen. then release all keys.
If you have a yellowish screen saying "Download mode, do not turn off the target", Man this is your lucky day
If I press those keys and release them after that samsung galaxy s logo, it gos into that black screen and vibrating thing again. If I keep pressing those 3 buttons for a long time it just rebooting continuously (samsung galaxy s logo appears-disappears-appears-disappears-appears-disappears etc until I release the buttons and goes into that black screen)
So, to be clear what is going on with the phone. It's turned off. I turn it on and it displays that samsung galaxy s gt-i9000 logo, then that animation with that sound..and that's all. After that..a black screen and vibrations
If you can not get to download mode that is a thing to consider. no download mode mean no odin
In that case i think you have to get a custom USB flashing cable to get into download mode. i saw ebay have that cable for a low price
http://forum.xda-developers.com/showthread.php?t=819551
Or return phone to vendor for repair .
jje
you need to hold vol down + home + power while the phones off and it should go into download mode.
what rom did you have before trying JPY?
My brother is leaving town after a few hours and he needed the phone. Eh...)
I will buy a microUSB cable and mod it for download mode. If that's not working...I will go with it on a service. Thank you guys. I thought that something could be done, even the 3 buttons method doesn't work
Okay I was using odin one click it was at rebooting device after it completed pushing stock onto the phone thats when I discounted the usb.... should have waited two secs I know but now the phone doesn't seem to get past the att world phone screen keeps looping over and over I have tried all the key combos different times and ways, vol up and down being held doesn't get to download mode the screen remains black plunging in seems to get to charge mode where even plunging into the wall charger it loops trying to calculate the battery status... any method I haven't tried... I did get it to boot once full and was usable didn't think to redo odin at the time and restarted back to this mess...tried three different jigs using the 100k 5% X3 even through its not a full brick due to the button combos gotten no where. Please Help
Search the forum to build a jig in order to get into download mode. Or you may need to buy one just in case in the future.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139
Try this:
Open Odin and plug your cable into your computer but not your phone yet
Pull battery on phone and put it back in
Hold both volume buttons down and then plug your phone in
It should go into download made and you can reflash the stock ROM
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
norcal einstein said:
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
Click to expand...
Click to collapse
Ahah Thats the same exact steps I was able to get the phone to boot that one time instead of the up down I was still attempting it to get past the loop holding the power button instead using those steps, if I had know it would have been one of the only times I would see it in there I would have pushed it to download with adb though...
can't test getting it to download mode now took it back fit the description of the standing on/off issue with the device still honored by warranty. And I wouldn't have posted without searching everywhere to make a jig, I made three of them though I noticed it still didn't get to download mode. I made sure that the last two jigs were done correct. Think that when it was disconnected from odin it wasn't done finalizing after the stock push gah >,< live and learn and do something else to the cappies XD.
Thanks for the link placing an order just in-case ~whistles looking around then side to side pushes another rom~ lalala
To offer my own advice if it ever happens again, what I've been able to do is:
1. Pull the battery out
2. Put it back in
3. Open Odin
4. Hold Both Volume Buttons (without holding the power button)
5. Plug the phone back in
It went immediately into download mode for me, Odin managed to time out several times while I was trying to flash a co-worker's Captivate to the official Froyo leak. One of those times I couldn't even get the phone to come up with any screen. I really do think this thing cannot be bricked.
BeowulfShaeffer said:
That has been my experience so far, too. I've "bricked" twice, once with an "all black" screen, and once with the phone-!-computer screen. I've yet to need a jig, though I thought I may have needed it last night when I got the "all black" screen.
Keep trying the different button press methods to get into download mode. It took me 4 attempts to get from "all black" to "phone-!-computer" to a happy robot digging away.
Click to expand...
Click to collapse
if you are out of luck, you may have to build a jig or buy one online.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139
Ive used odin before changing roms and have gotten to download mode with combos on my last cappy before that night (dramatic music) en ways..
did some more digging on this bad ass info and learning community "XDA" hehe as to how it got the way it did, I found out I was updated with the new patch when I sent it for screen change to this shop, so...using odin one click with this creates a hang time to where it looked like it was finished after pushing jh6 (which was totally off should have used odin 3 and pushed jh2 then clockwork update to jh7) so thats when I disconnected (second noob mistake of the situation) basically blowing the finalization out and key combs for recovery and download mode. and im guessing the jig was made wrong too at this point >,<.
Oh
wmason92 said:
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Click to expand...
Click to collapse
If you cant get your jig to work take it in to warranty (if your water inicators are sound and no physical damage) and say its power cycling on off at random times (which is true.. ) and it did it when you were sync to mini kies, did it an hour after the OP heh good luck
and I have yet to see the infamous yellow pc sign >,> <,< it can stay on the yellow brick road... thanks for the responses btw
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
Purchase jig from ebay, or google and try igo jig.
If your phone is turning on with jig you are not touching the right prongs. I know, I know it is not easy, but unless it if touching just right, it can turn your phone on.
Holy ******** i got it to download mode! For some reason i kept touching the same pins and nothing would happen. After about readjusting for about 5mn it finally worked!!!!
It has to be just so. Happy to hear
Wait, now its in download mode but my computer keeps saying usb device not recognized.
wmason92 said:
Wait, now its in download mode but my computer keeps saying usb device not recognized.
Click to expand...
Click to collapse
That happens try a different usb port or just borrow someone else computer, I used my networking classes computer my laptop was doing the same thing when I was change roms.
Changed the title to fit the issue, this is not a soft brick this is a boot brick that can affect the charge indicator in power off state as well. So whats the difference the soft brick is when you flash a rom incorrectly and you get the att world screen constantly staying on, the key combinations still work when the phone is like this.. in the case with a boot brick the att screen cycles over and over and the jig may or may not work I haven't been able to fully test it here in this state I have seen a packager attempt to finish once on the recent one but all the key combos I could find didn't function my noob guess is the phone forgot how to ride a bike (meaning is hasn't connected keys to recovery that was being flashed or hardware to there states without being booted normally) ultimate fix is if its in warranty (meaning no physical damage or water) take it back for power on off. the soft brick i've seen before and have fixed with odin 2-3 three times, and ive seen a blown kernel type too where keys and odin fix up like new.
wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
glaze76 said:
I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Very odd - I've never heard of that with a jig.
glaze76 said:
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Have a link to which one you have? It sounds like the solder points on the jig were a little weak. This can happen if they aren't good welds. If you want give one of mine a shot. I'll refund you if it reboots your phone...
Buy one HERE...
I had a boot brick happen to me just the other day. I was running Andromeda 1.1 with stock kernel & modem, and tried to tinker with swapping the AT&T boot screen using connexion2005's video on the subject (NOT insinuating any blame at all, his videos are fantastic).
I tested it successfully the first time, then flashed back the i9000_param_lfs, and pushed a new image to the device again (everything was exactly the same, with the exception of the boot_screen.bat script not making the phone ask for superuser approval while pushing the new logo_ATNT), and everything looked ok.
Reboot device, and...boink.
Black screen, no image at all on power on, only charging screen when usb cable connected. ADB, nothing. 3 button, nothing. Vol up+down, remove battery, insert usb cable, do hokey pokey, nothing. 5 attempts at the 100k resistor jig, for hours, nothing. No download, no recovery. Seems like the phone was toast.
Strange how I had just done this successfully earlier in the day, to now having it completely hard brick this phone.
I ended up taking the phone back to a local warranty center, and they swapped it (1008) for a 1010 (gps works fantastic on this one, btw)...I just hope there's no bill coming if they find out it was rooted and flashed. *crosses fingers and uses any and all karma*
Any ideas what happened? Did I scramble this things boot loader? I've heard how hard it is to fully brick this phone, and looks like I succeeded. How lucky.
I'd just like to know what went wrong so when I (or anyone else) root and flash next time, the chances of this happening are reduced (or better understood).
Thanks
I tried searching for this, but wasn't really sure how to phrase my problem, so I apologize in advance if this was posted (it probably was).
So heres the deal, I was using the leaked 2.2 on my captivate and decided to flash it back to 2.1. Well when Odin was just about finished doing its thing, my computer crashed before it finished. Now when i hit the power button, the first AT&T screen comes up, then it goes black, and a few seconds later the screen comes back. It does this until I pull the battery. Same thing when i plug in the usb, but with the charging screen instead.
So when I hold all 3 buttons for recovery mode, it just does the at&t screen thing, and when I hold the volume buttons and plug in the usb, it does it with the charging screen, therefore i cant get into download/recovery mode.
If anyone has any suggestions on how I can get it into download mode? If not, I'll go ahead and order a jig, i'm just hoping to avoid doing that if I dont have to. Thanks.
I've heard of a few "tricks" to getting it in to download mode, but Its always a good idea to have a Jig around. Have you though of making one? probably faster, and maybe cheaper as well.
CornyCorn said:
I tried searching for this, but wasn't really sure how to phrase my problem, so I apologize in advance if this was posted (it probably was).
So heres the deal, I was using the leaked 2.2 on my captivate and decided to flash it back to 2.1. Well when Odin was just about finished doing its thing, my computer crashed before it finished. Now when i hit the power button, the first AT&T screen comes up, then it goes black, and a few seconds later the screen comes back. It does this until I pull the battery. Same thing when i plug in the usb, but with the charging screen instead.
So when I hold all 3 buttons for recovery mode, it just does the at&t screen thing, and when I hold the volume buttons and plug in the usb, it does it with the charging screen, therefore i cant get into download/recovery mode.
If anyone has any suggestions on how I can get it into download mode? If not, I'll go ahead and order a jig, i'm just hoping to avoid doing that if I dont have to. Thanks.
Click to expand...
Click to collapse
Were you using the leaked 2.3 or 2.2? The same thing has happened with me when I used the leaked 2.3 GB. Look up on how to use ADB if your computer will pick up your phone. I had to do that to get back to 2.1 using odin one click, but yet the same problem still goes on with the 3 button trick not working and pluggin the usb in with volume buttons and it still going to the charge screen.
I'm gonna go out on a limb and suggest you flashed 2.3 not 2.2 as froyo has been an official captivate rom for all carriers for about 6 months now.
So how about trying the gingerbread method of volume up + power for recovery and volume down + power for download mode.
If you find that working for you then use your 1 click on a computer that isn't prone to crashing. Or you will hard brick your phone this time.
No, I'm positive it was the leaked 2.2 rom. I had been using it for months, since before the official update came out.
Anyways, I got myself a jib and was able to get into download mode. I used Odin to flash 2.1 again and it was successful. However, It still just goes into that boot screen loop when I start it.
Any idea why that is? Could it have something to do with the bootloaders?
no not a bootloader issue.
what is the build number on your phone? its on a little sticker on the phone under the battery 4 numbers first 2 are year second 2 are month, some phones 1010 and and after bootloop when odin one click is used. just use the full version of odin with a different firmware besides jf6 (there are 2 in the one click thread at the bottom of the op)
I have the same problem. My build number is 1105 and I need to get to 2.1. Whenever I use odin one click I go into a bootloop. My phone shipped with 2.2
My build number is 1009. Im about to try using the full Odin3 with the firmware found here:
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
E: Ok, that worked for me, I'm back to 2.1 JH2 right now. Gonna try to understand all this stuff a little better before I flash again. Thanks for your help everyone!