Related
k i had to unroot my fone cuz my apns was acting up. so my question is.
right after i update the spl, while in still in recovery
flash the rom that i have on my g1.
then reboot right.
it should have the arrow pointing down right. then followed by the g1 then loading screen.
Whenever updating to the latest SPL do these things first...
- Upgrade your radio to the latest version and confirm that it has been flashed
- Flash the SPL and give it time. Do not pull the battery if there are icons still on the screen. If you do you run the risk of bricking your G1
- Once flashed, check to see if the SPL has been flashed (reboot, CAMERA+POWER)
- If all clear then flash your desired ROM
hiroots said:
k i had to unroot my fone cuz my apns was acting up. so my question is.
right after i update the spl, while in still in recovery
flash the rom that i have on my g1.
then reboot right.
it should have the arrow pointing down right. then followed by the g1 then loading screen.
Click to expand...
Click to collapse
I think the SPL restarts your phone during the installation. I don't think you get the choice of whether you want to install the ROM at the same time *I think* (I haven't installed the SPL in a while). I don't think its required at any rate. Just reboot the phone into recovery once you're certain that the SPL flashed correctly.
Just make sure you get the radio first, haha. You shouldn't need to unroot because your APN's aren't working, just wipe and reflash...that normally fixes a lot of problems.
NeoBlade said:
Whenever updating to the latest SPL do these things first...
- Upgrade your radio to the latest version and confirm that it has been flashed
- Flash the SPL and give it time. Do not pull the battery if there are icons still on the screen. If you do you run the risk of bricking your G1
- Once flashed, check to see if the SPL has been flashed (reboot, CAMERA+POWER)
- If all clear then flash your desired ROM
Click to expand...
Click to collapse
both of the times ive rooted and installed that spl i would flash it and it would go to g1 screen twice, after a couple of minutes the second time i just pull battery, put in card reader (or have an extra card handy with a build) and copy a build onto it, then boot into recovery and flash it. its worked twice this way for me...
i have recovery 1.3.1 and if you flash the spl it wont reboot. so should i push the old recovery, then install the spl. then let it reboot, then flash my rom.
hiroots said:
i have recovery 1.3.1 and if you flash the spl it wont reboot. so should i push the old recovery, then install the spl. then let it reboot, then flash my rom.
Click to expand...
Click to collapse
well when you install the spl, it will hang on the g1 screen, it needs a build. so oyu have to pull the battery and put a build/rom on the card, then boot into recovery and wipe and flash. At least these are the instructions i followed and it worked both times i did it...dont know if that answers your question. When i did it i think i flashed 1.3.1 after the spl but i dont think it should make a difference...have you read any of the various tutorials? some of them are not good so be careful
hiroots said:
i have recovery 1.3.1 and if you flash the spl it wont reboot. so should i push the old recovery, then install the spl. then let it reboot, then flash my rom.
Click to expand...
Click to collapse
Once the SPL is flashed on, you have to physically hit home+back or whatever it is to reset the phone, DON'T SELECT WITH TRACKBALL, or else it won't write anything. Once you do that, it should say writing hbootimg or something then restart. It will appear with an icon on the screen for a few, and I can't stress this part enough, DO NOT PULL THE BATTERY, or you have a paperweight. Once its done doing its thing, it will reboot into recovery on its own.
xsnipuhx said:
Once the SPL is flashed on, you have to physically hit home+back or whatever it is to reset the phone, DON'T SELECT WITH TRACKBALL, or else it won't write anything. Once you do that, it should say writing hbootimg or something then restart. It will appear with an icon on the screen for a few, and I can't stress this part enough, DO NOT PULL THE BATTERY, or you have a paperweight. Once its done doing its thing, it will reboot into recovery on its own.
Click to expand...
Click to collapse
fyi...
this is the thread ive followed twice and have successfully flashed the so called 'dangerous' spl twice. Unless I read it wrong it says 'pull the battery' after flashing the spl. Either way it worked
http://forum.xda-developers.com/showthread.php?t=534461
My post above was for anyone who has Cyanogen recovery. That was the problem I had when I was updating to Danger SPL
xsnipuhx said:
My post above was for anyone who has Cyanogen recovery. That was the problem I had when I was updating to Danger SPL
Click to expand...
Click to collapse
i see. i mustve flashed 1.3.1 after the spl then...
DMaverick50 said:
i see. i mustve flashed 1.3.1 after the spl then...
Click to expand...
Click to collapse
Danger SPL has been out longer then 1.0 if I remember correctly.
I know there are tons of guides around about rooting and what to do, I know how to do it and I have with my own phone. However, the guides are mixed, some a little old, some doing ADB which I didn't and I wanted to ask a simple few questions to check before I try to help someone else root their phone.
I'm thinking that this process will work but I'd really appreciate it if others could give me a definitive "yes" or "that'll brick it" type response.
Download Radio and SPL update from http://code.google.com/p/sapphire-port-dream/
Download Cyanogen's 1.4 recovery img
Flash to RC29
Copy recovery image to replace the default using terminal after accessing root.
Install Radio update from recovery.
Install SPL update recovery.
(optionally install a new firmware at this point too)
I know there are guides, I've read them, I know what they say but I don't know if this method would work as it is slightly different and uses the new Cyanogen recovery image whereas others link to an older recovery image and Cyanogen's would mean less steps.
you can you use cyanogen's recovery as the one you put on the phone to begin with. the easiest way to do that is to change its name to recovery.img so when you are in telnet just type the command as you normally would. you can install the radio and spl with cyanogen's recovery image just do not use the trackball, use the keyboard and home and back to reboot. also you have to have a rom after flashing "danger" spl because it wipes the current rom. any other questions. i know starting with cyanogen's recovery will work because i have done it on other people's phones.
Oh right, that's great to know and thanks for the heads-up on the need for a replacement ROM david. If it was my phone I wouldn't have asked but this is to give pointers to a friend so I wanted to be more cautious.
Seems like this would work then..
Downgrade to RC29, gain root access on boot up.
Install Cyanogen's 1.4 recovery image and reboot to console.
Flash Radio
Flash SPL
Flash new ROM
Reboot
Is that it or would they need to reboot after flashing the radio then flash the SPL and new ROM? You say don't use the trackball, I know there are ALT+<key> shortcuts so I take it this is due to an issue before you have the new radio and SPL installed.
With regards to the trackball, how would you select one of the options for flashing "any zip on SD" if you can't scroll up and down?
there is a problem with the radio and spl updates not getting written when using the trackball. i have personally noticed it. also when flashing the spl or radio do not reboot from the recovery console as i know that will not write it as well here are the steps i use on someone elses phone.
download all files i need first.
downgrade to rc 29
substitute cyan's recovery for jf's recovery in the flash_image recovery recovery.img command for gaining root access. like i said just change the name of cyan's recovery to plain old "recovery.img" and no change in the commands typed will be needed.
flash radio
flash spl
flash rom
should be it.
How would you flash the three separate files in 1.4? Since it added the ability to flash any zip file if you don't change the name you can use that to pick what you want but I don't think you can select any item without using the trackball.
Or are you suggesting swapping the SD card out, putting each file on as update.zip one at a time and doing it that way?
you should be safe without renaming to update.zip but don't use the trackball to reboot. if it doesn't work just do the renaming to update.zip
When I tried using cyan's recovery in telnet it said it was read-only and I couldn't use it. Any idea why?
terminal su
I have a g1 w cupcake I formatted my 4g sd card did the alt s alt w and alt l went to the terminal emulator typed in su and got permission denied hellllllllp
Sounds like you missed a step before going to terminal.
"After your phone starts up, hit the enter key twice, type "telnetd" and press enter. (Yes, it will start up a contact search, don't worry. Just type it.)"
After you do that bit you go to terminal and connect to localhost. It's worth pointing out that you won't see anything here to show it's worked. You go back to terminal and go from there.
This is a little out dated but it'll help you root. And it has pictures..
http://gizmodo.com/5146797/how-to-hack-android-for-multitouch-web-browsing-on-the-t+mobile-g1
OK I'm in need of some help here and the faster the better as I'm talking to my friend via IM. So far we've downgraded to RC29, flashed Cyanogen's 1.4 recovery image and updated the radio. Next is the SPL but when it's applied this error comes up.....
multiple firmware images
can't store hboot image
failure at line 1:write_hboot_image PACKAGE:hboot.img
Instalation aborted
We haven't gone any further yet, halp.
are you doing haykuro's spl or hard spl? try hard spl if it is not already on the phone.
It's the SPL from here which I believe is Haykuro's.
http://code.google.com/p/sapphire-port-dream/
The current SPL will be whatever is stock, it's the first time it's been rooted.
try flashing the hard spl first then because i have always flashed it first. http://koushikdutta.blurryfox.com/G1RootWalkthrough/HardSPL/update.zip
Alright. Is there any reason why you would want Haykuro's SPL over the Hard SPL?
so you can flash hero and rogers builds. i have haykuros spl but i have whenever rooted a phone i have always flashed the hard spl first, so try flashing it before flashing haykuros spl
Ah ok. I'll keep that in mind. thanks again david. We're gonna give that a go now.
let me know if it works out
OK we had to pop the SD card out to copy the Hard SPL over but now it won't recognise it back in the phone. Is it safe to reboot and go back to recovery after flashing the radio or is there another way to get it to see the card I'm forgetting?
power the phone down, insert the card, reboot into recovery, then flash the hard spl. if it doesn't recognize the card then nothing will happen when you try to flash
[Guide] How to for "1-click rooting" -Read Before Making a Thread about 1-click root
This only applies to the HTC Dream/ T-Mobile G1, flashing the Hard SPL to any other phone will BRICK your phone. if you want to do this for the MyTouch 3G then read up on the rooting process for it, so that you will have a better understanding of what you need! Some rational thought and logical reasoning is needed to do this or any other hack to your phone.
If you think that doing any part of this will brick your phone then please ask your question first in this thread. Either that or somewhere around the top of the screen is a button that kill a man in the wrong hands (search), use it or leave a reply or pm me if you are not entirely sure of what you are doing.
Hopefully this will help with the numerous amounts of questions about one click rooting.
Please ask any questions pertaining to one click root in this because it will be easiest for me to see what you have done and where you are stick or what your question is pertaining to. Thank you.
Disclaimer: I have not done this by this method, but from what I understand this is how you should do it. Also I am not responsible to any damage to anyone's phone. If you do this to a mytouch 3G and it gets bricked because you flashed the Hard SPL to it, then I will laugh at you because you cannot read (GMT -5 12:39pm 8-25).
Now to begin with...
1. Download Cyanogen's latest stable release from here.
2. Place that file on the root of your sdcard i.e. the up most folder or the one that appears when you open it on your computer. or not in a folder on your sdcard
3. Go to the market and download Recovery Flasher, or download it from here if it has already been shut down on the market.
If you get it from here make sure to go to settings-applications-and check unknown sources and hit ok in the box that pops up.
To install it from the sdcard ( for simplicity put the file on the root of your sdcard again) just find it with a file manager ( I like Astro) and select it then select install.
4. Run the Recovery Flasher app.
5. Click make a back-up first in case something goes wrong (second button).
6. Click install recovery image (first button)
7. Power your phone down.
8. Hold home and power to boot into recovery.
9. Select apply any .zip from sd.
10. Select the Cyanogen ROM you placed on there from step 2.
11. Hit home to flash it after selecting it.
12. When it is done flashing hit reboot system now with the trackball or hold home and power to reboot the phone.
13. The initial boot up after a rom can take anywhere from 5 to 10 minutes. If it takes over 15
press send, menu, and power at the same to time to reboot then hold home to boot into recovery. if you cannot manage to do this for some reason then yank the battery and hold home and power to boot into recovery.
select wipe data/factory reset, hit home to apply
Reflash the rom from the above steps.
Reboot and wait for it to boot up.
14. When the phone boots up and is usuable, if you had to do a factory wipe then you will have to sign into google again. if not then your phone should be good to go from there
if you didn't wipe and get a lot of force closes then you will need to power down your phone and wipe by booting into recovery (home and power) then select wipe data/factory default, then hit home to wipe, then reflash CM 4.0.1 after the wipe and reboot when it is done flashing.
15. To check your Radio, go to settings-about phone-baseband version the second part of that number will be 2.22.19.26I if you have the new radio. If it is not that number then download the latest radio from the HTC website
16. place the radio on the root (not in a folder on your sdcard) of your sdcard.
17. power down your phone and boot into recovery.
18. apply the radio by going to flash any .zip from sd, then select the radio file, then hit home to flash.
19. when the radio is done flashing, reboot with home and back.
20. Now that you are rooted and have a rom and the latest radio on your phone there is one more important matter to take care of, flashing the Hard SPL.
21. Download the Hard SPL
22. put it on the root (not in a folder on your sdcard) of your sdcard.
23. power down your phone and boot into recovery.
24. apply the Hard SPL by going to apply any .zip, then select the hard spl, and hit home to apply it
25. After the Hard SPL is flashed, reboot the phone by holding home and back.
26. Enjoy. You have a rooted phone that has the SPL and Radio requirements it needs.
If you would like to know about partitioning your sdcard look at this guide and skip down to the part about partitioning your sdcard.
If I have left something out please let me know and I will update this post to include it. Thanks.
i r newb, hear me roar..
wondered if you, good sir or some other nice guru would mind helping me.. im new to this whole rooting business.. i have a stock uk t-mobile g1 with nothing moded at all..
so what does this recovery flasher actually do? does it mean i dont have to downgrade to rc7?
what do you do about getting a theme? and is easy to switch themes?
i think you have forgotten the nandroid backup step before flashing rom?
many thanks, please excuse my newbieness
when you place the radio or the hard spl into your root of your sd card do you have to rename it to update or just put it like it is???
Thanks for this. I was actually piecing the info together myself from various threads on here. Just a quick question, would you recommend creating the ext2 partition before or after flashing the rom?
@APEX.7 it flashes the recovery image to your phone allowing you to skip downgrading. if you nandroid before flashing a modded rom, well i guess it would you stock back since i have never tried that i would not know, but i will add in OP later about amking one. To flash a theme just put it on root of sdcard and boot into recovery and flash like you would anything else. To wipe the theme just flash the rom over it.
@forken you do not have to rename to update.zip with cyanogen's 1.4 recovery image
@esskaypee you can make the ext2 partition before flashing the rom but given the nature of 1 click root that if you leave recovery without a modded rom it might revert back to stock reocvery so as long as you do not reboot without a modded rom you are safe. I think cyanogen's rom will detect the partition and do it automaticallly when you add one but if it doesn't just reflash the rom to activate a2sd after making the ext2 partition.
Sorry for lack of better explanations and grammer but i'm at work on my g1 right now.
Thanks David!!!
Nice guide, On step #13, instead of having them "Yank the battery out" just press Talk+Menu+Power to reboot, then just hold Home. Thats less hassle. . Also, i suggest having them flash the RADIO first, then the SPL. LEss chance of brick...
nephron said:
Nice guide, On step #13, instead of having them "Yank the battery out" just press Talk+Menu+Power to reboot, then just hold Home. Thats less hassle. . Also, i suggest having them flash the RADIO first, then the SPL. LEss chance of brick...
Click to expand...
Click to collapse
I typed up something like this in that silly guide in the dev secion. For funzies I'll post it here too:
THIS METHOD SHOULD ONLY BE USED WITH THE G1/DREAM AND NOT THE SAPPHIRE/MyTouch
Backup all needed files from you SD card
Download and install Recovery Flasher
Open up recovery flasher and click flash recovery
Download the newest radio and place on root of SD card
Download Hard SPL and place on root of SD card
Download ROM of choice (Recommend Cyan 4.0.1) and place on root of SD card
Turn off phone
Boot in recovery holding HOME+POWER button
Select "apply any zip from sd" using either your trackball or pressing Alt+A
Select the radio file and install
After installation press HOME+BACK to reboot into recovery
Select "apply any zip from sd" using either your trackball or pressing Alt+A
Select the Hard SPL .zip file and install
After installation press HOME+BACK to reboot into recovery
Once in recovery wipe by hitting either Alt+W or scrolling with trackball
Select "apply any zip from sd" using either your trackball or pressing Alt+A
Select your ROM and install
After installation press HOME+BACK
There you go you are rooted with the newest rom! If you wanna go advanced and flash Haykuro's SPL then just follow this.
With your phone off, turn on holding CAMERA+POWER
Somewhere in the top-right you should see either PVT or DVT written somewhere. If you have a DVT board, stop reading because you can't flash this new SPL. If you have a PVT board then just follow along
Download the newest radio and place it on the root of your SD card
Download Haykuro's SPL and place it on the root of your SD card
Download the rom you are currently running right now and place it on the root of your SD card
Reboot in recovery
Select "apply any zip from sd"
Select and install your RADIO file and hit HOME+BACK when finished
Once you're in recovery again select "apply any zip from sd" again and choose the SPL file and install. After installation press HOME+BACK
Once you get into recovery again select "apply any zip from sd" once again and choose your ROM file. After installation press HOME+BACK
You're done!
EDIT:
Another thing for the new people beginning to root. If you guys decide to take the time to root then take the time to learn the information needed before flashing anything and not expect to be catered just because you are new. All the info for all you're little question are out there. Just put in the effort to search. If you don't want to put in the effort to search for the info then don't bother rooting.
nephron said:
Nice guide, On step #13, instead of having them "Yank the battery out" just press Talk+Menu+Power to reboot, then just hold Home. Thats less hassle. . Also, i suggest having them flash the RADIO first, then the SPL. LEss chance of brick...
Click to expand...
Click to collapse
they are flashing the hard spl in this guide. why would the radio be needed before the hard spl? when i rooted my phone i used the hard spl then the new radio was released a month or so after. anyways i think most of them will have the new radio anyways.
david1171 said:
anyways i think most of them will have the new radio anyways.
Click to expand...
Click to collapse
It's always good to check if the latest radio is installed, but for anyone with an unmodded phone this should be the case as it was part of past updates.
I'm going to root my G1 shortly & will report back with my findings. I have however made lots of research, so I don't expect there to be any problems.
help pls
can some1 tell me do i need to install hard spl and ota radio if everything after installed CM 4.01., recovery 1.4 and dark hero theme works ok?
if i have to do that pls tell me step by step how...
thx
Hey Guys,
i've installed CM 4.0.1 and Recovery 1.4 (with Recovery Flasher), but without Hard SPL and OTA Radio before, after that installed Dark Hero Theme and all works ok.
can some1 tell me do i need reinstall everthyng and install hard spl and ota radio, and how can i do that?
thx
Right, I'm now also a proud owner of a rooted G1. Everything went without a hitch. I did not install radio (had the newest) and no SPL (not planning on changing the Rom from Cyan).
@sasa3791 look at steps 16 through 25 in OP. to flash something boot into recovery (home and power), go to apply any .zip from sd, select the name of your file, hit home to apply, then reboot using home and back. i will update OP with this info later.
@esskaypee glad its working
@everyone who thinks they do not need the hard spl. i hope you never want to try another rom other than cyanogen's. yes i know they are nice but they make nandroid so if something goes wrong or if you want to play with other roms. also i hope that none of you ever need fastboot since the stock spl is apparently so great.
noobie question but whats puttin an file on the root mean? (english not my first language)
thanks
plus can you install a theme like you install a rom in the recovery boot?
forken said:
noobie question but whats puttin an file on the root mean? (english not my first language)
thanks
plus can you install a theme like you install a rom in the recovery boot?
Click to expand...
Click to collapse
Putting a file on the root of the card means just put it on the card in no folders.
Yes just install a theme like a rom, just make sure the theme is compatible with the rom.
Flash radio before flashing SPL
nephron said:
Nice guide, On step #13, instead of having them "Yank the battery out" just press Talk+Menu+Power to reboot, then just hold Home. Thats less hassle. . Also, i suggest having them flash the RADIO first, then the SPL. LEss chance of brick...
Click to expand...
Click to collapse
Yea,
I should have assumed it would be the same procedure as on the G1, I went and followed the original post and bricked my MT3G. Gonna get another one and be sure to FLASH RADIO FIRST BEFORE SPL. Besides this minor hiccup, everything has been great. Thanks to everyone for all the help and great information.
pwillikins said:
Yea,
I should have assumed it would be the same procedure as on the G1, I went and followed the original post and bricked my MT3G. Gonna get another one and be sure to FLASH RADIO FIRST BEFORE SPL. Besides this minor hiccup, everything has been great. Thanks to everyone for all the help and great information.
Click to expand...
Click to collapse
you manually root the mytouch with the haykuro's spl which is the one for the sapphire which, guess what, is the same phone as the mytouch with more ram basically. i will go back and note in the OP that this only applies to htc dream/ t-mobile g1. could that be the reason i put it on the dream section?
sasa3791 said:
Hey Guys,
i've installed CM 4.0.1 and Recovery 1.4 (with Recovery Flasher), but without Hard SPL and OTA Radio before, after that installed Dark Hero Theme and all works ok.
can some1 tell me do i need reinstall everthyng and install hard spl and ota radio, and how can i do that?
thx
Click to expand...
Click to collapse
you can start by searching
Is it bricked?
So
8. Hold home and power to boot into recovery
Worked great.
I decided to make a backup
After making the backup i cleared everything and
Told the phone to put back the backup.
Placing back the backup worked fine as well.
Then I rebooted... and the phone hangs in the "android" screen.
When I boot with “Home” and “On” button pressed I get a default android question mark screen.
So I decided to do it the old-fashion way:
http://forum.xda-developers.com/showthread.php?t=442480. I tried both the RC29 and the RC7 version but I after the rainbow screen I get a white screen saying loading, then checking and then saying "not allow" with a red "00028002" above it.
I would love to have see my phone work again so any help is appreciated.
Alright.
Title basically explains it all. I'm not an expert at messing around with my phone, but I'm not a novice either.
I do everything through trial and error. My phone has the correct Radio and SPL. Yes, I flashed the Radio before the SPL. The phone isn't bricked because it will go into recovery mode. But apart from that, it's all that it will do.
I was running RA's V1.5.1 recovery. Now it's at JFV1.43.
I think my mistake was trying to update from ADP1 straight into Cyanogens 4.2.7.1.
I had a ADP1 phone and tried to update to Cyanogens 4.2.7.1, and everything just went downhill from there. I never managed to accomplish my set goal, which was to flash and run Cyanogens 4.2.7.1.
Then when that didn't work. I tried downgrading to RC29 and just re-rooting my phone. By this time I was running RA's recovery V1.5.1. That went as planned until I flashed the latest radio and spl and wanted to upgrade to the modified version of RC30. I flashed the RC30 ROM. At this time, it wouldn't get past the blinking Android screen with the bot. I thought it kept on getting stuck there because it required the hard spl. Whether the latest spl and the hard spl are the same thing, I don't know. I flashed the hard spl. That's where my stupidest mistake probably happened. That's when my phone decided it didn't want to go past the G1 screen when rebooting/booting.
Is there anything I can do in order to fix this? And can someone explain to me a proper method of flashing Cyanogens 4.2.7.1 ROM? Is there anyway I can connect with my phone through adb on JFV1.43 recovery and just flash RA's V1.5.1 recovery through there and push a new ROM?
Frustration builds. Lol.
What I want to have on my phone is RA's V1.5.1 recovery with Cyanogen's 4.2.7.1 with the Eclair theme.
Many thanks in advance to whomever decides to grant me some much needed help.
OK, as long as you can still access your Recovery menu then you're not bricked.. so smile lol.
Rememeber, before you install the Cyanogenmod 4.2.7.1 ROM you need to install the HTC 1.6 Dev Rom first.
HTC took it off their website, i have it uploaded on my site...
do this: ( This is for HTC Dream (G1) )
CLEAR YOUR EXT PARTITION or REPARTITION YOUR CARD to get rid of any Incompatible files.
Download CM 4.2.7.1 -> http://www.myhangoutonline.com/downloads/?did=17
Download HTC Dream Image 1.6 -> http://www.myhangoutonline.com/downloads/?did=6
Place them both on the root of your SDCard.
Reboot your phone into recovery mode...
1. WIPE
2. Install HTC Dream Image
3. Hit Reboot when it's done (and keep an eye on the phone!)
4. you will see the little picture with an arrow (radio installation), WHEN YOU SEE THE PHONE REBOOT HOLD THE HOME KEY. It should reboot right back into recovery.
5. Now install the CM ROM
6. Reboot and you're done...
Hope that helps!
mrandroid said:
OK, as long as you can still access your Recovery menu then you're not bricked.. so smile lol.
Rememeber, before you install the Cyanogenmod 4.2.7.1 ROM you need to install the HTC 1.6 Dev Rom first.
HTC took it off their website, i have it uploaded on my site...
do this: ( This is for HTC Dream (G1) )
CLEAR YOUR EXT PARTITION or REPARTITION YOUR CARD to get rid of any Incompatible files.
Download CM 4.2.7.1 -> http://www.myhangoutonline.com/downloads/?did=17
Download HTC Dream Image 1.6 -> http://www.myhangoutonline.com/downloads/?did=6
Place them both on the root of your SDCard.
Reboot your phone into recovery mode...
1. WIPE
2. Install HTC Dream Image
3. Hit Reboot when it's done (and keep an eye on the phone!)
4. you will see the little picture with an arrow (radio installation), WHEN YOU SEE THE PHONE REBOOT HOLD THE HOME KEY. It should reboot right back into recovery.
5. Now install the CM ROM
6. Reboot and you're done...
Hope that helps!
Click to expand...
Click to collapse
I'll try that and see how it goes. One question though, do I rename them to "update.zip" like always, or no? I'm gonna get an sd card reader to follow through with the procedure you gave me.
Thanks a lot.
If you are still showing recovery JF1.43, update your recovery first to either AR 1.5.1 or CM1.4. Once that is done, you won't need to rename anything, just select the update any zip option from recovery.
Dont reboot in between the htc image & cyanogen rom..It even says that on his site..This is what to do..
1. wipe
2. update from and zip the pick the htc image
3.update any zip and pick the cyanogen rom
4.Now reboot
5.should go to recovery and reboot one more time
6.Bam your done and no one got hurt either
sockpuppet4 said:
If you are still showing recovery JF1.43, update your recovery first to either AR 1.5.1 or CM1.4. Once that is done, you won't need to rename anything, just select the update any zip option from recovery.
Click to expand...
Click to collapse
Can I do this through the recovery screen console option? (flash_image recovery /sdcard/recovery-RA-dream-v1.5.1.img)?
mrandroid said:
OK, as long as you can still access your Recovery menu then you're not bricked.. so smile lol.
Rememeber, before you install the Cyanogenmod 4.2.7.1 ROM you need to install the HTC 1.6 Dev Rom first.
HTC took it off their website, i have it uploaded on my site...
do this: ( This is for HTC Dream (G1) )
CLEAR YOUR EXT PARTITION or REPARTITION YOUR CARD to get rid of any Incompatible files.
Download CM 4.2.7.1 -> http://www.myhangoutonline.com/downloads/?did=17
Download HTC Dream Image 1.6 -> http://www.myhangoutonline.com/downloads/?did=6
Place them both on the root of your SDCard.
Reboot your phone into recovery mode...
1. WIPE
2. Install HTC Dream Image
3. Hit Reboot when it's done (and keep an eye on the phone!)
4. you will see the little picture with an arrow (radio installation), WHEN YOU SEE THE PHONE REBOOT HOLD THE HOME KEY. It should reboot right back into recovery.
5. Now install the CM ROM
6. Reboot and you're done...
Hope that helps!
Click to expand...
Click to collapse
The links posted aren't working for some reason. I tried going to the website to look them up and no go. If I can just get a proper link to download the HTC 1.6 Dev Rom I should be good to go.
I finally got the things I wanted to run.
Many thanks to the people that helped.
well i tried to install the hero 2.1 rom and i have the android system recovery utility build: JKv1.41 and it doesnt apply the update right nor does it wipe and factory update i just reboot and it shows the g1 sign goes off and starts recovery again can someone please help!!!!!!!
You are not bricked
If you can get to the recovery image, then you are not bricked. You can flash a different rom to get your phone back to where you want it to be. Or you can restore your nandroid backup (if you made one) from the recovery.
Which recovery image are you using? What ROM are you flashing from?
Do you already have the Danger SPL and new radio needed for a Hero ROM?
go to recovery, go to console, type in ums_enable, put a different rom onto your sd card, wipe your phone, and flash the rom.
hopefully you got your phone back to working order.
Are you trying to flash hero without the Danger SPL? Only reason i can think of why it wouldn't flash.
WOW you cant brick a phone from roms!
Hasnt that been said many times?
You dont know that brick is, when you really have you will know
Its one of those instincts that you get
Downgrade your radio and you will know what a true Paper weight is.
melterx12 said:
go to recovery, go to console, type in ums_enable, put a different rom onto your sd card, wipe your phone, and flash the rom.
Click to expand...
Click to collapse
when I type in ums_enable its says not found
Then flash the recovery in my sig.