Flashing with one-clock started, it said that setting up .pit file and then averything stopped.
I was waiting for 20 minutes it didn't finish flashing.
When I turned phone on I saw phone-comp logo.
Went back to Download mode, got 512.pit file, opened odin and tried to do repartition. same result.
HELP PLZ!
With odin open and your usb cable ready to plug in take out the battery from your phone. Then put it back in. Then very quickly hold the both volume buttons down and plug the usb cable in. You will enter download mode and odin will recognize it.
Quick suggestion. Use odin one click to flash back to stock and do a master clear or you will continue having issues.
Sent from my SAMSUNG-SGH-I897 using XDA App
I did the same the other day. Blamed the tiredness. To repair I flashed jpo with odin with 512 pit, pda, phone and csc files and re partition ticked. Then updated to jpy, installed custom kernel and away you go.
If you're going to flash with pit files and re partition you must also have the pda, phone and csc files. Or so I read. Worked for me anyway. As long as you have three button recovery and can access download mode you'll be fine.
Sent from my GT-I9000 using XDA App
So i tried to updated to a custom firmware after i JUST received my galaxy S back.
And it got bricked.
It failed during the initial flash with Odin, no big worry i thought as i'll just reflash it. It constantly failed until I changed the USB slot. Now after I've even completed the flash the phone boots up shows the "GT-i9000/m" logo then shows those 9 bars that show its trying to load the battery charger. Then the screen goes black and it tries that over and over again.
Anybody had this problem? I think it's a soft brick and can be resolved before sending it back in and losing the phone for another month.
is download mode working then ? does odin recognise the phone ??
if so download a stock firmware with all 3 files and pit. and use re-partition. and see how that goes.
actually if it is a software problem there are lots of possible procedure to fix that just reflash it with an official firmware using odin
I've tried the following:
use odin 512pit and a tar file and using odin with a 803pit and a tar file.
Both resulted in the same thing.
Is there a specific FW i should try?
edit:
With and without repartitioning.
try JM8 with PIT and pda.modem,csc. and re partition again.
I know wher eto get JM8, but how/where do I get the PDA.modem and csc?
hmm yea i know what u mean, most modern firmwares only come in 1 file now. download that. but im not sure what pit to use. il have a look now.
i think its 512 pit
here try this
Tried everything. I think it might be a hardware error.
Last ditch effort of Jm8 in odin 1.0 now... will let you know if it works.
Edit:Nothing worked.
Gonna go return the phone/send it back to samsung.
Double EDIT:
Flashed the phone back with JL2 that i got from Samsung and checked EVERYTHING in ODIN. Phone went past the boot logo repetition and into the "S" but doesn't do anything more. Just gets stuck after that. (corrupted internal SD)
so if the JL2 didnt succeed what would be on it at present ? if its a custom rom just go back to odin do a flash and disconnect half way through and totally brick the phone..
then blame it on a kies update when you return it. you dont want them to find out you have modified it in any way not recommended by samsung. or they may not replace and may charge you.
Purchased two Bell Canada Samsung Galaxy S as-is from local kijiji.
They all performing the same thing, rebooting at Galaxy S logo, GT-I9000M page, it won't go any further. and there is no recovery mode at start-up.
Here are the steps which I have played with for past two days.
1. Trying to get to recovery mode
- tried ADB, but it doesn't work, since "USB debug" is not on, and it won't accept as a device, and I am not able to turn that on, since I can't even get on the main screen.
- tried three key combo, vol up + home + power on, at least a hundred times for past two days, it doesn't work. fortunately download mode is working (at least I have more option to try). and I know how to get to recovery mode, I played with my friend's before.
2. Trying to use ODIN to flash the firmware
- unchecked "re-partition", unchecked "bootloader", pick 512 as PIT and then choose following as PDA
JH2, JK3, JK4, JL2
always successful on refresh, but phone still does the same, stuck at LOGO page
- also tried, checked "re-partition", and checked "bootloader", pick 512 as PIT and repacking following into PDA, Phone/Modem, CSC, still won't work...
JP series, JH, JK series, JL
At the beginning I though it was problem on CSC, I didn't use correct one to match my phone model #, but what's mine??? I can't go into my phone to check. I checked my friend's I9000, he used I9000BMCJK4, and I assume all JK series should work with me, since our IMEI are similar. And I tried many times on different cache.rft as CSC.tar, still no luck for me
I go crazy now, $400 USD gone. Seriously needing help. Any help is highly appreciated.
try the one jl2 download file and samsungfirmwares.com it flashes a special bootloader that may fix things.. it should be a single file you put in as pda nothing else..
if not they may have permantely trashed internal memory and you are sol.
lgkahn said:
try the one jl2 download file and samsungfirmwares.com it flashes a special bootloader that may fix things.. it should be a single file you put in as pda nothing else..
if not they may have permantely trashed internal memory and you are sol.
Click to expand...
Click to collapse
I have tried one of JL2 file from somewhere (don't remember where), but I will get one JL2 file from samsungfirmwares.com again, see if that works.
Do you mean, only choose the file for PDA, left PIT empty, and get everything uncheck?
permantely trashed internal memory? are these the common problem with this model? I got two of these, and both of them have the same issue, I think, there should be a way to slove it, right? Should I give up these thoughts???
anyways, thanks anyways, I will report back after I flesh JL2 from samsungfirmwares.com
Ok, you need to flash jl2 with pda, repartition, pit file and the secondary boot loader... The SBL(secondary boot loader) is what will actually fix your phone
Hopefully it will work.
Sent from my GT-I9000m using XDA App
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
<ID:0/005> Sbl.bin
<ID:0/005> zImage
<ID:0/005> factoryfs.rfs
<ID:0/005> modem.bin
<ID:0/005> param.lfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Still no luck on this firmware, I9000UGJL2, by the way, should be samfirmware.com instead of samsungfirmwares.com
above message I got from ODIN3 v1.30, it looks fine for refresh, but it doesn't work. the phone keep rebooting, it won't pass LOGO page, again, only download mode I can use.
HELP! HELP! HELP!
any leads???
is "<ID:0/005> Sbl.bin" secondary boot loader???
I got the file for PDA, I9000UGJL2, is this the one? if not, where should I get it? how do I update it?
I did it again, with "re-partition" checked, PIT choosed as s1_odin_20100512.pit, I9000UGJL2_homebinary_add_param.tar (which I just downloaded from samfirmware.com), it still doesn't work.
anything else I can try? maybe something simple I didn't do???
I too am a bell user I had the same problem a few weeks back. This is going to sound messed up, but i'm going to do my best to explain how I solved the problem.
DO NOT MULTI-TASK ON THE COMPUTER WHILE DOING THIS. CLOSE ALL OTHER APPLICATIONS.
-remove external sd and sim card
-go into download mode (hold vol down+power+home).
-turn on ODIN
-plug in usb (both computer and phone)
-check re-partition
-ONLY use the 512 pit file. DO NOT use a rom.
-start ODIN and it should only take a minute. this will wipe your device completely but still allow you to access download mode.
- remove usb close ODIN
- start up ODIN again and connect usb
- use 512 pit and JP1 or JP2 rom.
- After flashing, this SHOULD give you an error and send you straight into recovery mode. you're looking for a specific error code. you need the error to have "sl01" or "sl10" (whichever, i forgot which it was) at the end of the path. if the end of the path has "m(something)" then use a different rom till you get the "sl10".
these errors are internal sd errors which your phone is experiencing right now, but the phone is fixable from the "sl10" error.
continuing...
- once you get the "sl10" error, close ODIN, unplug USB, turn off phone.
- go back into download mode.
- boot up ODIN with 512 pit and ULG2 rom.
- plug in phone
- start flashing.
this can give you two outcomes:
1) fixed galaxy S
2) error code with "m(something)" at the end of the error path.
if it's #2 do this all over again until it works.
This took me 3 days to figure out these steps, 10 hours each day. although it doesnt seem to make sense, my phone is working right now and it is where I am writing all this from. My only explanation is that Bell gets ****ty product from samsung. it's almost impossible to flash custom roms on a bell galaxy i9000 because the internal SD seems to have trouble being mounted.
i hope this helps and i hope it doesnt take long for you to fix this problem.
btw, if it does get fixed data connection wont be available. to enable it go to your apn settings. create new named "Bell" with apn as "pda.bell.ca" and leave all other options blank. data should be restored after that.
Sent from my GT-I9000M using XDA Premium App
jt_kyle said:
I too am a bell user I had the same problem a few weeks back. This is going to sound messed up, but i'm going to do my best to explain how I solved the problem.
DO NOT MULTI-TASK ON THE COMPUTER WHILE DOING THIS. CLOSE ALL OTHER APPLICATIONS.
-remove external sd and sim card
-go into download mode (hold vol down+power+home).
-turn on ODIN
-plug in usb (both computer and phone)
-check re-partition
-ONLY use the 512 pit file. DO NOT use a rom.
-start ODIN and it should only take a minute. this will wipe your device completely but still allow you to access download mode.
- remove usb close ODIN
- start up ODIN again and connect usb
- use 512 pit and JP1 or JP2 rom.
- After flashing, this SHOULD give you an error and send you straight into recovery mode. you're looking for a specific error code. you need the error to have "sl01" or "sl10" (whichever, i forgot which it was) at the end of the path. if the end of the path has "m(something)" then use a different rom till you get the "sl10".
these errors are internal sd errors which your phone is experiencing right now, but the phone is fixable from the "sl10" error.
continuing...
- once you get the "sl10" error, close ODIN, unplug USB, turn off phone.
- go back into download mode.
- boot up ODIN with 512 pit and ULG2 rom.
- plug in phone
- start flashing.
this can give you two outcomes:
1) fixed galaxy S
2) error code with "m(something)" at the end of the error path.
if it's #2 do this all over again until it works.
This took me 3 days to figure out these steps, 10 hours each day. although it doesnt seem to make sense, my phone is working right now and it is where I am writing all this from. My only explanation is that Bell gets ****ty product from samsung. it's almost impossible to flash custom roms on a bell galaxy i9000 because the internal SD seems to have trouble being mounted.
i hope this helps and i hope it doesnt take long for you to fix this problem.
btw, if it does get fixed data connection wont be available. to enable it go to your apn settings. create new named "Bell" with apn as "pda.bell.ca" and leave all other options blank. data should be restored after that.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
great!!! Another option I can try. Thank you.
I will try it out right after my work. so the idea behind this, is bricking it into recovery mode and S10 error code. and then fresh right back with correct ULG2 (is this correct? frist time heard about this rom)
anyways, I will post back with result.
Where can i find this ULG2 rom?
did it work?
Thananjeyen said:
Where can i find this ULG2 rom?
Click to expand...
Click to collapse
I think jt_kyle meant I9000UGJL2
and you can get them from samfirmware.com
Paallikko said:
did it work?
Click to expand...
Click to collapse
yes, lucky I got one of my Bell Samsung phone work. Since I done a million times of refreshing and rebooting and etc... I am not sure what I did, now I still trying to remember last 10 steps I did to make this work.
But definitely, I could not have done this repair without jt_kyle. Thank you so much, jt_kyle.
jt_kyle, Thank you!!!
but none of JP1 or JP2 is givining me the error "tl10", I tried
I9000DXJP1
I9000TGYZSJP2
I9000XXJP1
I9000XXJP2
it come out error started with "m..."
I just keep refreshing each on PDA 3 to 4 times, and choose with re-partition or without. At the end I try a few another ROMs as well, I still get no "tl10", but somehow, just that magicical moment, the screen come out a set of commands that look like format sd card, so I got excited, fresh it with JL2. It is back to work.
still no clue the steps of fixing the problem.
one done, the another one to go.
any more ideas please, and I think I am really close to solve this one now.
Thank you All
FIX
Look for a file called I9000UGJL2Complete follow the same steps pit and so on after your phone boots up youll have a blank baseband then you get the I9000UGJL2 modem and flash it where it says phone this has unbricked a few for me hope this helps
EVERED78 said:
Look for a file called I9000UGJL2Complete follow the same steps pit and so on after your phone boots up youll have a blank baseband then you get the I9000UGJL2 modem and flash it where it says phone this has unbricked a few for me hope this helps
Click to expand...
Click to collapse
if you have a way for me to give you this file i do have it just not sure how to do so because its 286MB
Could it be dead?
Since you have one of the infamous i9000m's it might also just be a dead SD card? You might try calling samsung and trying to get it repaired under warrenty as they are all under a year old (try and flash jl2 first even it will not boot up). It sounds like no receipt may not be an issue.
Lots of info from allgamer's list of i9000m issues in the general section.
At least you have one in the meantime!
same problem
Hey ive got pretty much the same problem that you had. Only differences are that I'm from Australia and am on Virgin network.
My phone became semi bricked one day when it restarted and since the 3 button combinations did not work i ordered in a USB jig which i received today. I used odin 1.8 to try and flash to I9000BVJJPD which i got from samfirmware.com but it ended up stuck on the logo screen vibrating once in a while. I decided to repeat it with no avail and began to use other roms and use .PIT.
This is where my phone became even worse and is now in it's current position; rebooting at the GT-I9000 page. I tried the method that jt_kyle suggested, substituting australian roms instead but it is still in the same position.
Does anyone have any other suggestions or should i just try getting a warranty?
Look for the ugjl2 complette and repeat what I said
Sent from my GT-I9000 using XDA Premium App
EVERED78 said:
if you have a way for me to give you this file i do have it just not sure how to do so because its 286MB
Click to expand...
Click to collapse
I think I have this I9000M_JL2_JL2_JL2_JL2_UG_BMC file, is the same file that you are talking about? JL2 Complete?
I tried this file many times, it won't work neither.
for past one hour I played around this phone, trying to repeat the steps I did for the first phone. Unfortunately, nothing is working for me AGAIN!
but I got these error page all the time, like following...
update media, please wait
E:Can't mount /dev/block/mmcblk0p1
(I/O error)
E:copy_dbdata_media:Can't mount SDCARD:
I think that's bigest problem in my case, and for a lot of people in this forum. Do any people has a good solution for this???
New member and somewhat stupid for trying to do this:
Long story short I attempted to throw gingerbread 2.3.X on the phone and now its stuck in either download mode, recovery mode, or if i just turn it on it comes up and says "GALAXY S GT-I9000 Samsung" The last thing that was successful was putting the SpeedMod Kernel on it.
In recovery mode it says "ClockworkMod Recovery v2.5.1.0 SpeedMod ULFK" on top and bottom.
The phone started out with factory settings.
When i try and use the ODIN 3 and try to do the Mast Clear it says :
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> Master Clear Started.....
and then stays like that indefinately...
Same thing with hitting "start"
Please let me know how to fix this, I know there are some really brilliant individuals on this forum and it would be greatly appreciated.
search for odin, download it, follow the steps and flash back to stock. you'll be fine especially since you can get into download mode.
edit: gah you already have odin. do you have one click or the one where u have to put the pit and tar files?
the same advice applies though, find the stock files, and go into download mode, then plug it in and flash back to stock.
i think master clear only works when the phone is on and you have usb debugging enabled.
Ive got ODIN 1.7 and ODIN3. I can get them to both recognize the phone but when I try and hit "start" with v1.7 it ust sits there forever. and Im not able to get ODIN3 to do anything either.
Any way you could provide a more step by step solution?
If you're having problems with ODIN, something that seemed to work for me was to remove my SIM card.
Try removing it and see if you have any luck.
I dont have anything in the phone, no sim and no external.
Just left it alone for a bit and came back and turned the comp back on and everything worked for ODIN. Thanks for the help fellas
I have a Galaxy Tab 7, T-Mobile version (although I only use wi-fi, not data). I flashed once before using Overcome and it worked perfect, but after my tab started acting crazy - constantly crashing and rebooting - I tried to re-stock and re-flash. I went through the first steps - pit, GB safe stock, T-Mobile modem...and it all went fine, except it was stuck in boot. I tried the hidden pit, which I found in a troubleshoot thread - still stuck in boot.
Then I tried the dbdata.rfs in PDA, which I came across on Fix My IT System...still stuck in boot, and now if I try to load GB safe stock in PDA, I get a fail. Twice I have unplugged in Download, because of Fail and not advancing download...and both times when connect to Odin and load dbdata.rfs in PDA it resets and I can re-enter download mode and recovery<3e>, but it's still stuck in boot.
Is there any hope for me?
If you are restocking and still failing, there is a possibility that your internal nand chip is failing. Also the fact that it suddenly start crashing initially.
There may be ways to run cm rom on external sd that is properly partitioned, if you still want to get some live out of your tab.
Sent from my GT-N7100 using xda app-developers app
priyana said:
If you are restocking and still failing, there is a possibility that your internal nand chip is failing. Also the fact that it suddenly start crashing initially.
There may be ways to run cm rom on external sd that is properly partitioned, if you still want to get some live out of your tab.
Sent from my GT-N7100 using xda app-developers app
Click to expand...
Click to collapse
The thought had occurred to me, although I did fix the Odin stock load fail with some further digging (re-loaded USB drivers, plugged cable into different port). Still boot looping...doesn't even boot enough to get adb logcat.
P1 add hidden doesn't help, and makes the next attempt fail, and I have to reload drivers. Same with dbdata.rfs. Although after reflashing dbdata.rfs I can get to recovery<3e> and boot into download. Checksum fails after P1_add_hidden and after dbdata.rfs, but not after USB reload and GB Stock Safe flash. Still stuck at Samsung logo, though.
Is there any way to find out if the chip is my problem for sure, short of tearing the Tab apart?