Database Develop

[Q] Captivate With I9000 Firmware Stuck in Recovery Mode

There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all

An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.

same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....

You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse

hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.

yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!

and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!

pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down

That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.

I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks

xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable

i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.

Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.

Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?

JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!

SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories

yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139

agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post

I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.

drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro

[Q] Stuck in REcovery boot

Ive tryed to root my Captivate with One click root
but my Windows crash when the Captivate reboot
so now im stuck in recovery menu and i cant use Power button
some one can help me?

Download odin one click if you haven't already. Open Odin, remove battery. Plug battery back in, hold only both volume buttons and plug USB in phone.
This is my captivate. There are many like it but this one is mine.

how many time have i have to do this before it works?
because i see my captivate open... my batteri reloading and 4-5sec after he go to the Recovery

or some one know how to mount the SD card
without the phone?

[Q] Bricked acaptivate trying to flash recvoery...

Ok i was running a custom version of 2.2 FroYo on my captivate and it was running fine. I backed up my old version using Clockwork Recovery. Well i decided to get brave and flash back to my stock 2.1 ROM.
When i did that alls i can get is the AT&T boot screen. It will sit there for an hour if i left it. I tried entering recovery bode (power, vol up/down) but it just sits at that screen.
Is there any hope to recovering it? I use a MAC but im about to boot Win7 on it to run ODIN, but i cant get into any flash/recvoery mode....
Suggestions?

You want to try and get into Download Mode, not Recovery. Have you tried the various button combos to get into Download Mode yet?
If the various button combos ultimately don't work, you can use something called a JIG to force your phone into Download mode.

What is the button combo for download mode? also with is 'JIG'? Im no total newb but i am new to this who flashing/kernel modifying thing.
I have a Nexus S now which i love but i need the Galaxy running for my AT&T company SIM card....
Also do i NEED ODIN?

There are like 4+ different button combos for Download Mode. If you search, I'm sure you'll find them all. The one I remember is:
1. Remove battery, SIM, microSD card (if you have one)
2. Wait at least 10 seconds with the phone off
3. Hold Volume Up/Volume Down keys, do not let go
4. While holding the volume keys, insert the battery into the phone
If this worked, the phone should almost instantly be in Download Mode.
Once in Download Mode, you want to use Odin (generally the One-Click JF6 version) to flash your phone to a working state again.
A JIG is a microUSB plug that will force your phone into Download Mode, if Download Mode is still possible on your phone. You can make them with a MicroUSB plug and resistors, or buy one. The link in my signature is an example of what a purchased one would look like.

Help, choose wrong phone for ROM Manger and now stuck in Android Recovery Mode

Help guys.
I have a Samsung Galaxy S Captivate I897. Last night I installed the Clockworkmod ROM Manager in there and was messing around with it.
I choose my phone model to be the the I9000 and then I went into recovery mode to restore the previous ROM, but guess what? It went into recovery mode, the volume up and down buttons select the menu items and it asks me to hit the "OK key" to enter.
The Captivate doesn't have an OK key, it uses the power button. So the Android Recovery Mode here thinks the phone is a I9000 and I can't get it to do anything other than reboot into that mode.
I've tried using the ADB to try to get back into download mode but it's no longer reading the phone. The volume + power buttons to go into that mode has never worked for this phone either.
I'm at a loss at what to do. Is there anyway I can get out of recovery mode and into download mode or back to regular phone usage here? Would I need to take it to an android developer?
Thanks for your help.
Thanks for your help.

vancouverguy said:
Help guys.
I have a Samsung Galaxy S Captivate I897. Last night I installed the Clockworkmod ROM Manager in there and was messing around with it.
I choose my phone model to be the the I9000 and then I went into recovery mode to restore the previous ROM, but guess what? It went into recovery mode, the volume up and down buttons select the menu items and it asks me to hit the "OK key" to enter.
The Captivate doesn't have an OK key, it uses the power button. So the Android Recovery Mode here thinks the phone is a I9000 and I can't get it to do anything other than reboot into that mode.
I've tried using the ADB to try to get back into download mode but it's no longer reading the phone. The volume + power buttons to go into that mode has never worked for this phone either.
I'm at a loss at what to do. Is there anyway I can get out of recovery mode and into download mode or back to regular phone usage here? Would I need to take it to an android developer?
Thanks for your help.
Thanks for your help.
Click to expand...
Click to collapse
Shut off the phone, open up odin(DG's flash to stock one) hold the power and the menu button. Once you see the ATT screen release the power while continuing to hold the volume buttons. Once odin recognizes your device flash to stock using the utility. Once this works donate to DG for saving your ass. Also, quit using ROM manager. Just use the update.zip method everyone else uses.

+1 for just using CWM update.zip It is sooo much easier/faster.

Thanks, but it didn't work. My Galaxy S is one of those where the volume + power buttons don't work to get it into download mode.
I did try power + menu as you suggest, but that doesn't work either.

try this
1. open odin.
2. With phone unplugged remove battery
3. with battery removed plug phone into pc via USB
4. with battery still removed simultaneously hold down Vol. + / - (forget about power button just hold down the two vol buttons)
5. While holding down the vol + / - insert the battery (keep the vol buttons down and hopefully DL screen comes up)

silverslotcar said:
+1 for just using CWM update.zip It is sooo much easier/faster.
Click to expand...
Click to collapse
I cannot stress this enough.
Also, OP, if the above doesn't work, it might be USB jig time.

pwr isn't used to go into dload mode - that would turn your phone on.
Do this:
Open odin
Remove bat, sim, ext mem card
replace bat
hold vol -/+ and plug in data cable to computer
(should be download mode)
If that fails, then get yourself a jig... gotta search for the thread though - should cost a couple dollars. Then once you're back up... look up the thread to fix the 3 button combo.

You might try turning the phone off then hold VOLUME DOWN and POWER (not vol up/dwn/pwr) to get into download mode. Make sure to remove the sim and sd cards.

I bricked my phone over the weekend and had similar problem you did.the easiest way too get out in to download mode is a jig. Its easy and cheap to do.look on you tube under un brick captivate fort a tutorial.
Sent from my SAMSUNG-SGH-I897 using XDA App

Question about using update.zip to install clockwork recovery after flashing to stock (and avoiding Rom Manager):
Is rooting still required?

doreyu said:
Question about using update.zip to install clockwork recovery after flashing to stock (and avoiding Rom Manager):
Is rooting still required?
Click to expand...
Click to collapse
Nope. No root needed

mcord11758 said:
Nope. No root needed
Click to expand...
Click to collapse
Awesome, great that would be hugely faster, thanks.

doreyu said:
Awesome, great that would be hugely faster, thanks.
Click to expand...
Click to collapse
Once you learn that trick you are on stock for like 2 minutes before you flash

Yeah I'm kind of a lurk but I've been around for about a month just flashing everything, and I had no idea it could be done like this till today. Going to make my next one even faster.
Sent from my SAMSUNG-SGH-I897 using XDA App

Nothing seems to work.
I'm going to try the jig method Wednesday morning. Wish me luck!

I tried the jig and it didn't work.
What happened was that it got me back into recovery mode, not download mode. Tried it several times. So unless I'm hitting the wrong points on the phone usb plugin (other than the last two), I'm hooped.
I tried the direct resistor wire to points in usb plugin method. I didn't try the one where I cut open a mini-usb cable and use the plug as a dongle, although I think it may get the same result.
What do you guys think?

Help...Cant get phone into download mode.

I used odin 1 click to get phone back to stock . Now my phone will not go into dl mode with any of the button combos.Also i can not get into recovery.Other than those 2 things the phone boots up and works.Any help please..

Which Odin one click ? And what were you running before you did the one click?

Use a jig for dl mode.

You tried Vol Down-Power and then after the splash screen releasing the power button and continuing to hold Vol Down.
Does your phone fully boot? If it does and you have adb on your computer. Turn on USB debugging, connect the phone to your computer via USB, and then use the command 'adb reboot download' without the '
Hope that works for you.

I used odin 1 click flashed phone back to eclair 2.1 I897UCJF6..The phone will boot into eclair and function properly but i cant get to dl mode or recovery.thanks for the responses

Its risky but IF YOU ARE ON 2.1 YOU CAN FLASH THE 3 BUTTON FIX, or flash i897 gingerbread bootloaders, but DO NOT FLASH THE 3 BUTTON FIX AFTER FLASHING THE GINGERBREAD BOOTLOADERS OR YOU WILL BE HARD BRICKED YOU HAVE BEEN WARNED!!!!!!
Sent from my SAMSUNG-SGH-I897 using XDA App

holeindalip said:
Its risky but IF YOU ARE ON 2.1 YOU CAN FLASH THE 3 BUTTON FIX, or flash i897 gingerbread bootloaders, but DO NOT FLASH THE 3 BUTTON FIX AFTER FLASHING THE GINGERBREAD BOOTLOADERS OR YOU WILL BE HARD BRICKED YOU HAVE BEEN WARNED!!!!!!
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
I would recommend i897 GB bootloaders instead of the 3 button fix. It still fixes the button problem, but never, never, never flash the 3 button fix after flashing GB bootloaders. You have been warned again.

ok finally got into dl mode but when i plugged phone up to usb it went to the phone ! computer screen what do I do.Thanks in advance..

jnblackmon30 said:
ok finally got into dl mode but when i plugged phone up to usb it went to the phone ! computer screen what do I do.Thanks in advance..
Click to expand...
Click to collapse
Does Odin recognize the phone? If so, just flash from there.

odin will not recognize.Any sugestions? Thanks
will a jig get me to d/l mode from here?

jnblackmon30 said:
odin will not recognize.Any sugestions? Thanks
will a jig get me to d/l mode from here?
Click to expand...
Click to collapse
It should. Also, hold volume up + down, then plug in USB should also. Before you try that, restart your computer and pull the battery on the phone for a couple minutes before trying again. Have Odin open before you plug in the phone. Make sure you are using a pry on the back of the computer ( #1 on a laptop).

Followed ur directions still no go.You have any other ideas without a jig?Thanks

jnblackmon30 said:
Followed ur directions still no go.You have any other ideas without a jig?Thanks
Click to expand...
Click to collapse
No. I used a jig last time it happened to me. They only cost about $10.

thanks for all your help.I ordered 1 from ebay...thanks again

No problem. Hope you get it.

Have you tried adb?
Sent from my SAMSUNG-SGH-I897 using XDA App

jnblackmon30 said:
ok finally got into dl mode but when i plugged phone up to usb it went to the phone ! computer screen what do I do.Thanks in advance..
Click to expand...
Click to collapse
I had this a cpl of times, u'll have to reinstall drivers (uninstall first) ,or I use kies mini to reinstall drivers all the time when the pc won't recognize it (this usually happens after switching bootloaders), reboot ur pc and after that ur pc should pick it up (found new hardware). Once the drivers are loaded head back to odin and this time ur com port should light up.

Try this method for download mode... It's worked on every build captivate I've tried, even the fabled 1008 build.
1. Turn off phone, pull battery, sim card, sd card
2. Open ODIN (optional)
3. Plug in USB, then hold both volume buttons (NOT power button)
4. Re-insert battery while still holding volume buttons.
Phone should instantly boot into download mode