Hi there,
I'd like to overclock my IncS to 1,3 Ghz...
But I don't know the right settings.
Can you please tell me the right setting for best performance (e.g. oc to 1,3ghz) and best battery life?
thanks
does anybody know?
Set max to your desired, min to the lowest it will go and scaling to smartass.
I'm OCd to over 1.4 and no issues... UCd to 192 with smartassv2 governor
Sent from my Incredible S using XDA App
the best performance I have experienced in my INC is when I put oc / uv beater to the following:
wake gov: ondemand
wake mins: 245000
wake max: 1228800
Sleep gov: Conservative
my sleep: 245000
Sleep max: 691200
when I take a test in antutu nenchmark for I the following result.
score: 2729
If I clocked lower or higher, the result is lower
Overclocking depends entirely on your chip.
You should use whatever governor suits your needs.
I personally use ondemandx which speeds up on demand (as the name implies), conservative tries to keep the frequency as low as possible, interactive uses max frequency if min isn't enough, smartass is an improvement of interactive that keeps performance high while improving battery life (meaning there's little reason to use interactive).
You can find it in more detail here.
So basically, smartass if you want performance, conservative if you want battery life, ondemand if you want something in between. In reality though, I don't think you'll see much difference between them and I've seen no difference in idle power draws, so if you don't use your phone all that much, they won't be that different.
Once you've picked a governor, you should set min speed to 122000 (no reason to use any higher) and max to whatever you want. Your phone will probably crash or suffer from bad performance if you go over 1.5 GHz, but it varies a lot. Might happen even earlier.
Once you've found your desired performance level, you should start tweaking your voltages. You can do that under the UV profile. In there, you can adjust voltages at different speeds and the phone will automatically use them at whatever speed it's at. You should undervolt to increase battery life, so start by reducing all by 25 or 50 and then temp apply. Use it like that for a couple of hours and if it doesn't freeze, you're probably stable. You can either stop here or spend many hours tweaking it further, but that'll take many hours to get right.
This is my setting
Sent from my HTC Incredible S using xda premium
Which would be the best O/C program out there ?! I have SetCPU, Daemon but I'm sure there is better in the market...... just need to know the name so I can get it Thanks!
I'm currently 230MIN/1150MAX
Me4oKyX said:
Which would be the best O/C program out there ?! I have SetCPU, Daemon but I'm sure there is better in the market...... just need to know the name so I can get it Thanks!
I'm currently 230MIN/1150MAX
Click to expand...
Click to collapse
In my opinion, and I'm sure many others', Virtuous daemon is the best by far.
It comes standard in a lot of roms, and using the OC/UV beater
http://forum.xda-developers.com/showthread.php?t=1207546
it would have the best performance. I've set mine similar to yours and with this method, you can set the phone to underclock when battery reaches a low level
Related
Hey guys. Just wondering which governor works the best for you guys. Want to find the perfect compromise between battery life and no lag while scrolling.
i find that snartassv2 works best for me
Sent from my GT-N7000 using xda premium
Lagfree using Abyss 2.6 does what it says, very smooth desktop scrolling in ADW EX, even at stock 1.4GHz.
Battery life seems ok, and heat is about the same as On Demand.
For SetCPU
- Use Ondemand, that will give performance when CPU need it
and In profile add power saver (200 min 500 max), when screen off. if compromise any SW then max 800
What is the necessity to set this profile if the phone goes into deep sleep? Many times we don't need apps working in the background...
For instance I disabled all the background activities of apps requesting data (autosync...) and I am always in deep sleep with screen off...
My 2 cents.
Cheers.
I see guys. Been bouncing back and forth between intellidemand, smartass v2 and lagfree. Lagfree seems to consume more batteries though
abyssPlug
Sorry to bring this thread back to life but I was wondering what everyone thought the optimal settings for CPU speeds would be.
Galaxy Note GT-7000
CheckROM
Abyss Kernel
On Demand governer
I have them set right now for min 200 and max 1500. I had the set at min 50 and max 1600 but the min 50 made the phone a little laggy.
Another question, what should I set the temp profile to temp wise?
Thanks in advance
right now im running ondemand....min 200 max 1664
abyss kerenl... stock rom....
seems fine to me....
I have just updated to Cyanogenmod 7.2 stable on my P990 Optimus 2x (Fido Canadian version).
When I go to the CPU settings I cannot change the min/max frequencies or select a CPU governor.
I have done some research and found kernels like Vork and FauxDS, but they are for 7.1 nightlies so I am not sure if it is a good idea to flash them.
What I am most afraid about is the possibility of getting the black screen of death while my phone sleeps (it happened once already but it stopped after I changed to a different charger and reflashed CM7.2).
The reason why I want to change the settings is that there tends to be scrolling lag (my old HTC Desire Z was faster!) and there is also a bit of lag waking up the phone (lockscreen does not appear instantly when pressing power button).
Does anyone know what is the best kernel I can flash to enable frequency/governor changes in CM7.2 stable? I would prefer not to change the ROM if possible as I am kinda nooby in comparison to the XDA community in general. Thanks for any help.
I suggest you try Etana kernel. It has the things you need. Also use CPU master to set profiles and minimum CPU frequencies. I used something like min freq 352 MHz when asleep (don't worry doesn't drain battery) and I had no lag whatsoever.
heavencanwait said:
I suggest you try Etana kernel. It has the things you need. Also use CPU master to set profiles and minimum CPU frequencies. I used something like min freq 352 MHz when asleep (don't worry doesn't drain battery) and I had no lag whatsoever.
Click to expand...
Click to collapse
Are you referring to http://forum.xda-developers.com/showthread.php?t=1427646 ?
If so, do I just flash the zip off the sd card using ClockworkMod? And what are the differences between lite and DS?
Thanks.
All right, after reading, I determined I don't need LOC/HOC/DS as I don't intend to raise the max frequency, I just want to raise min frequency.
Installed the Etana kernel via CWM and it works. I can raise minimum frequency, though I still cannot see a governor option! Any idea how to get my governor setting back?
You can use CPU master and set some profiles. It's not exactly the same as governors but it's as close as it gets and it gets the job done pretty well. As far as I remember there were two governors for O2X - powersave and performance. I've always used performance and I can't tell if there's a HUGE difference in battery usage. I guess performance utilizes higher CPU frequencies when the device is asleep and somehow scales faster to even higher frequencies when needed to. But this might be complete crap as I am not too much into how CPUs work...
And please use the THANKS button (right below the user name), it kind of forum etiquette and it keeps people motivated to help others. Thank the Etana developer too.
heavencanwait said:
You can use CPU master and set some profiles. It's not exactly the same as governors but it's as close as it gets and it gets the job done pretty well. As far as I remember there were two governors for O2X - powersave and performance. I've always used performance and I can't tell if there's a HUGE difference in battery usage. I guess performance utilizes higher CPU frequencies when the device is asleep and somehow scales faster to even higher frequencies when needed to. But this might be complete crap as I am not too much into how CPUs work...
And please use the THANKS button (right below the user name), it kind of forum etiquette and it keeps people motivated to help others. Thank the Etana developer too.
Click to expand...
Click to collapse
Thanks for letting me know, I didn't realize there was a thanks button at first haha.
Fixed!
As for now CPU Master in his profiles let's you choose governor. We have only 2. Power save nd Performance.
Sent from LG 2X using Tapatalk 2 Elite
Because both the ViperDHD and Team Venom beta forums are being used by people like us to discuss battery life, kernel tweaking and smoothness, I decided to change this into a universal Viper/Sense discussion thread. ANyone from the family of devices which include DHD, Desire Z, Desire S, IncS, dinc2, mt4g etc are welcome here. ACtually, everyone is.
The discussion was sort of started here
http://forum.xda-developers.com/showthread.php?p=37246862#post37246862
Feel free to post settings and everything. We are trying to get the most of our old devices!
Reserved
Reserved for something else
CyanVivo X, default kernel.
Screen off: 245 min/max
Screen on: 245min, 1228 max.
2 hours of screen on time, 3 hours when I'm lucky, 3G is killing my battery...
Frequencies: 61-1200 MHz redux kernel.
With ondemandx governor and deadline scheduler
Undervolted consolidatedly by -25
I manage to get a battery life of 14-16 hours.
Main usage: voice calls- 1-1.5 hrs
The only problem is... Battery never reaches 100%.
Any suggestions?
Sent from my oc'd viper vivo
Using tricksterMOD, you can see that governors like interactive and ondemand have their own settings. I have been playing around with these settings, and I am still not finished with what I like yet. However you can use this post as a guide:
http://forum.xda-developers.com/showpost.php?p=36743252&postcount=3113
With Interactive, you can set your go_highspeed_load to 806 or 768MHz. I have set my min to be 245MHz, max 1200MHz but highspeed load is 806MHz. This results in a kind of even split between the times that 245, 806 and 1200MHz are used. With ondemand or another governor, it generally spikes up to 1200MHz (your max freq) a lot, rather than scaling between the lower freqs. This results in more battery usage because you are staying at a higher freq for longer than needed. Performance is generally the same with interactive and ondemand if configured right.
What do these mean? Basically, with my device now when I touch the screen, it will ramp up to 806MHz. If the process is more than just moving something on the screen and more processing power is needed, it will automatically go to 1200MHz, and when its done and I am still touching the screen, it will go back down to 806MHz. When all I am doing is browsing xda or something, when I scroll it ramps up to 806MHz and when I leave it to read something, it will go down to 245MHz. Then obviously when its sleeping it goes into deep sleep (hopefully)
My battery life suckss.
Sent from one of the few remaining Incredible S'
markj338 said:
Using tricksterMOD, you can see that governors like interactive and ondemand have their own settings. I have been playing around with these settings, and I am still not finished with what I like yet. However you can use this post as a guide:
http://forum.xda-developers.com/showpost.php?p=36743252&postcount=3113
With Interactive, you can set your go_highspeed_load to 806 or 768MHz. I have set my min to be 245MHz, max 1200MHz but highspeed load is 806MHz. This results in a kind of even split between the times that 245, 806 and 1200MHz are used. With ondemand or another governor, it generally spikes up to 1200MHz (your max freq) a lot, rather than scaling between the lower freqs. This results in more battery usage because you are staying at a higher freq for longer than needed. Performance is generally the same with interactive and ondemand if configured right.
What do these mean? Basically, with my device now when I touch the screen, it will ramp up to 806MHz. If the process is more than just moving something on the screen and more processing power is needed, it will automatically go to 1200MHz, and when its done and I am still touching the screen, it will go back down to 806MHz. When all I am doing is browsing xda or something, when I scroll it ramps up to 806MHz and when I leave it to read something, it will go down to 245MHz. Then obviously when its sleeping it goes into deep sleep (hopefully)
Click to expand...
Click to collapse
I am gonna try nodding the governors now!
Sent from my Incredible S using xda app-developers app
Mark r these settings good?.... Btw what nr i should put to boost?
janarp said:
Mark r these settings good?.... Btw what nr i should put to boost?
Click to expand...
Click to collapse
Looking good to me
Smooth or not? Maybe post a screenie of cpuspy or something to see what you're running at
See here for more info
http://forum.xda-developers.com/showpost.php?p=19846297&postcount=2
Are you finding any slowdown and major battery drainage where android os keeps the device awake?
markj338 said:
Looking good to me
Smooth or not? Maybe post a screenie of cpuspy or something to see what you're running at
See here for more info
http://forum.xda-developers.com/showpost.php?p=19846297&postcount=2
Are you finding any slowdown and major battery drainage where android os keeps the device awake?
Click to expand...
Click to collapse
It feels really smooth right now.. i cant tell for battery because i flashed patcha kernel right now... Lets see how good my battery is after few days of using... Thanks for link i read it later... Dont have that time right now... And here is pic ... If u mean this offcourse..
or u can suggest me better kernel tuning app...
janarp said:
It feels really smooth right now.. i cant tell for battery because i flashed patcha kernel right now... Lets see how good my battery is after few days of using... Thanks for link i read it later... Dont have that time right now... And here is pic ... If u mean this offcourse..
or u can suggest me better kernel tuning app...
Click to expand...
Click to collapse
Not that one
The screen that shows how long you've been at what freq
probably i flash new Beast Mode MOD kernel if it release today... it looks more interesting..=)
---------- Post added at 03:57 PM ---------- Previous post was at 03:56 PM ----------
markj338 said:
Not that one
The screen that shows how long you've been at what freq
Click to expand...
Click to collapse
with this kernel tuner app i cant see that i guess..=)
hey all i m using advenced-sense-kernel-r1
i would like to set governors like markj338 posted.
"Using tricksterMOD, you can see that governors like interactive and ondemand have their own settings. I have been playing around with these settings, and I am still not finished with what I like yet. However you can use this post as a guide:
http://forum.xda-developers.com/show...postcount=3113
With Interactive, you can set your go_highspeed_load to 806 or 768MHz. I have set my min to be 245MHz, max 1200MHz but highspeed load is 806MHz. This results in a kind of even split between the times that 245, 806 and 1200MHz are used. With ondemand or another governor, it generally spikes up to 1200MHz (your max freq) a lot, rather than scaling between the lower freqs. This results in more battery usage because you are staying at a higher freq for longer than needed. Performance is generally the same with interactive and ondemand if configured right.
What do these mean? Basically, with my device now when I touch the screen, it will ramp up to 806MHz. If the process is more than just moving something on the screen and more processing power is needed, it will automatically go to 1200MHz, and when its done and I am still touching the screen, it will go back down to 806MHz. When all I am doing is browsing xda or something, when I scroll it ramps up to 806MHz and when I leave it to read something, it will go down to 245MHz. Then obviously when its sleeping it goes into deep sleep (hopefully)"
is there an easy way
right now i have these cpu stats and these oc settings
do i have to remove oc deamon and cpu stats to use tricksterMOD
mkdsa said:
hey all i m using advenced-sense-kernel-r1
i would like to set governors like markj338 posted.
"Using tricksterMOD, you can see that governors like interactive and ondemand have their own settings. I have been playing around with these settings, and I am still not finished with what I like yet. However you can use this post as a guide:
http://forum.xda-developers.com/show...postcount=3113
With Interactive, you can set your go_highspeed_load to 806 or 768MHz. I have set my min to be 245MHz, max 1200MHz but highspeed load is 806MHz. This results in a kind of even split between the times that 245, 806 and 1200MHz are used. With ondemand or another governor, it generally spikes up to 1200MHz (your max freq) a lot, rather than scaling between the lower freqs. This results in more battery usage because you are staying at a higher freq for longer than needed. Performance is generally the same with interactive and ondemand if configured right.
What do these mean? Basically, with my device now when I touch the screen, it will ramp up to 806MHz. If the process is more than just moving something on the screen and more processing power is needed, it will automatically go to 1200MHz, and when its done and I am still touching the screen, it will go back down to 806MHz. When all I am doing is browsing xda or something, when I scroll it ramps up to 806MHz and when I leave it to read something, it will go down to 245MHz. Then obviously when its sleeping it goes into deep sleep (hopefully)"
is there an easy way
right now i have these cpu stats and these oc settings
do i have to remove oc deamon and cpu stats to use tricksterMOD
Click to expand...
Click to collapse
You can't edit the governor settings with the daemon controller app. That's why we use the trickster mod app to edit things
By governor settings I don't mean switching governors, I mean the actual settings of it.
That stuff should disable itself but its best to remove them to avoid conflicts
Sent from my HTC Incredible S
My results on ViperIncS with z13boot.img, redux_0.8 kernel, daemon controller, 3G always On, 7 hours of sleepmode (0.8%/hour), sync ON, loged on on every account on my phone but with disabled updates for accounts.. only IM+pro is working all the time inpush mode.
hey markj338 i m new to this,so if i understand i should remove oc deamon and cpu stats but can u walk me trough setup trickstermode
removed oc deamon and cpu stats and installed trickster i have these screenshots
mkdsa said:
hey markj338 i m new to this,so if i understand i should remove oc deamon and cpu stats but can u walk me trough setup trikstermode
Click to expand...
Click to collapse
Delete them
Download an app from play store called trickster MOD kernel settings or something
Download busybox installer by stericsson
Install busybox using the app
open trickster, then you can set whatever you like.
screnshoots
ok removed oc deamon and cpu stats
installed busybox and Trikster got these settings..what should go_highspeed_load be now is 99...noticed when i restart dhd governor goes back to ondemand
tnx man
Q&A for [KERNEL][D5803&D5833] AndroPlusKernel
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [KERNEL][D5803&D5833] AndroPlusKernel. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
Thanks
Very nice kernel, fast and smooth - great work and port.
Anyone knows if it's possible to use any third party kernel app to boost the headset volume?
Working
Hi this is my first post, infact I joined so I could report my findings.
I would just like to confirm so far that V5 working on my Z3C using the .93 firmware. I didn't need to wipe cache/dalvik/data partitions either.
For purposes of settings configuration, I'll be using TricksterMod
For stress testing purposes I'll be using Stability Test 2.7
Overclocking
Overclocking seems to work, I'll stress test and report back with the results.
I was wrong, it is unstable when overclocking and stress testing, with the phone force rebooting 1-5 seconds in to the stability test which loaded all 4 cores. Tried 2899Mhz and 2880Mhz (were both unstable and didn't try 2.72, 2.75, 2.57 either - I might try stability testing them.) Was completely stable at 2.47GHz, and it actually stuck there, no throttling in place! I stopped the stress test when the CPU temp was around 77-80C as my hand was getting burnt! The battery temp reached about 46C. It took 10 mins of stress testing for this to be reached. When the stock kernel was in place it would begin throttling after about 1-20 seconds under full load. First 2.2GHz, then 2 then 1.7 then 1.5 and eventually 1.25 after about 2-4mins.
I couldn't do a single core test though. I suspect as most games use single core or dual cores it wouldn't get overly hot.
My opinion is that fast clocked phones should be marketed with 2 speeds. The highest it'll reach under a boost mode (turbo for Intel's i5 and i7 series), and a slower speed that it'll average out at under thermal pressure. The Z3Cs would be turbo: 2.5GHz and normal: 1.5GHz.
Governors
These are quick tests I'm performing here to provide a quick look at responsiveness and potential unnecessary CPU jump ups.
Wheatley - most of the time it's hovering at top speed when approx CPU usage is 9%, it'll occasionally hunt down to 300Mhz but then right back up to 2899MHz. This one is speedy though. Governor tunables available.
Lagfree - idles at 300MHz - 960MHz then hunts up to 2.2-2.9Ghz when needed and turns on the second core. It seems to slow back down to idle. This one seems to have fast scrolling, sliding notifications pane quickly). No governor tunables.
SmartassV2 - idles at 300Mhz, speeds up to 422-960 on core 0, and turns on core 1 at 1.2-1.5GHz for a few seconds under fast scrolling and notification pane opening. Seems quite responsive. Probably good for battery life hopefully with the responsiveness of Interactive. No governor tunables.
Lionheart - Idles at 960 MHz for a few seconds then slows down to 300MHz with the odd increase to 729MHz. Core 0 and Core 1 reaches 1.26GHz under scrolling, notification pane opening. As fast as the others. Governor tunables available.
Hotplugging
Intelliplug appears to work better than MP-Decision - now only one core is on during idle, instead of 2.
MP-Decision was disabled to avoid conflicts.
Undervolting
I've only undervolted 300MHz to 675MHz from 775MHz as of writing this post.
Tried quickly undervolting in trickstermod by setting them all about -75mV, stability tested it, appears stable. I'll tweak the voltages a bit better when I do a scaling stability test.
Issues I've experienced
Sound Control is the only thing so far that causes a reboot. However music still plays over the speakers and headphones. Equaliser works too.
Upon rebooting, the CPU top speed will set itself to 2.2GHz, despite being set higher and saved at a higher speed in Trickstermod. Certainly trivial though.
Strange thing I've noticed: On the undervolt part I've noticed that there is a freq called 3033MHz, but no 2899MHz freq. Just an observation.
Misc
Force Fast Charge confirmed working! Before flashing new kernel charge went up 5% in about half an hour. It's now up another 5% in a matter of 5-10mins. This is when plugged to my PC.
Vibrator strength - set to 20 from 31, much quieter on table and can still feel it.
I'd like to say a huge thank you to DooMLoRD and AndroPlus for developing this stable kernel. Now my Z3C is worth the £28 a month I'm paying for again. Since this silly lad decided to bork the camera, Bravia functionality etc by rooting it on the first day. I'll report back and edit the post with my findings.
Max won't go beyond 2.266 GHz, Min won't change.
Hi All,
Firstly, great job with the kernel. Our Z3C is such a capable piece of kit and this just makes it that much better.
I'm running stock, 23.0.A.2.93, unlocked, rooted.
Problem:
I've tried using both SetCPU and No-Frills and while both show frequencies that are supposedly selectable above 2.266 GHz, neither app would actually respond. Meaning the max frequency will still only be 2.266 GHz even if I tried selecting something like 2.458 GHz (which should be selectable given that stock is 2.458 GHz.) See caps.
In addition, the Min value just won't change at all from 300 MHz. The frequencies scale up and down as the load changes but I can't raise the Min (again using both SetCPU and No-Frills) from 300 MHz.
Tried: I've tried turning off stamina mode and frozen apps that could control CPU activity (e.g. I use DS Battery Saver). I changed up Governors and Schedulers. I've tried re-flashing the kernel and it still doesn't change these behaviors.
Question/Need help: Just wanted to ask if anybody else have any problems setting the max frequency beyond 2.266 GHz and/or changing the minimum frequency from 300 MHz? Would appreciate any help resolving this behavior.
Thanks in advance!
pjmanalo said:
Hi All,
Firstly, great job with the kernel. Our Z3C is such a capable piece of kit and this just makes it that much better.
I'm running stock, 23.0.A.2.93, unlocked, rooted.
Problem:
I've tried using both SetCPU and No-Frills and while both show frequencies that are supposedly selectable above 2.266 GHz, neither app would actually respond. Meaning the max frequency will still only be 2.266 GHz even if I tried selecting something like 2.458 GHz (which should be selectable given that stock is 2.458 GHz.) See caps.
In addition, the Min value just won't change at all from 300 MHz. The frequencies scale up and down as the load changes but I can't raise the Min (again using both SetCPU and No-Frills) from 300 MHz.
Tried: I've tried turning off stamina mode and frozen apps that could control CPU activity (e.g. I use DS Battery Saver). I changed up Governors and Schedulers. I've tried re-flashing the kernel and it still doesn't change these behaviors.
Question/Need help: Just wanted to ask if anybody else have any problems setting the max frequency beyond 2.266 GHz and/or changing the minimum frequency from 300 MHz? Would appreciate any help resolving this behavior.
Thanks in advance!
Click to expand...
Click to collapse
Try installing TricksterMod (from Google Play store, trust me, you'll love it!) Then go to General and set the max speed to 2.46GHz or higher, and try using the Ondemand Governor too. I noticed that it wouldn't stick properly sometimes when using Interactive governor. If it doesn't stick for you then turn Frequency Lock on. Then check in the info tab that it's hitting the higher speed. Personally I'd recommend leaving the min speed on 300MHz. If you need constant high speeds, select the performance governor.
DBCJoey said:
Try installing TricksterMod (from Google Play store, trust me, you'll love it!) Then go to General and set the max speed to 2.46GHz or higher, and try using the Ondemand Governor too. I noticed that it wouldn't stick properly sometimes when using Interactive governor. If it doesn't stick for you then turn Frequency Lock on. Then check in the info tab that it's hitting the higher speed. Personally I'd recommend leaving the min speed on 300MHz. If you need constant high speeds, select the performance governor.
Click to expand...
Click to collapse
Thanks! That did the trick!
Odd that my usual app for the job across 4 other phones - SetCPU - doesn't work on what should essentially be the same job. [emoji55]
Please make sound_control drivers work so its possible to boost headphone volume on the Xperia Z3 Compact... Thanks
Nice work, a lot of updates I like it!
Is it possible to add a change log?
Thanks!
kernel for d5803 with the .93 but not .105
i search a kernel for the d5803 with the last .93 french version of phone
.5.77
Works great! Thanks a lot
Link for Z3C_D5803_AndroPlusKernel_v10.zip is dead
Pls upload in another location.
Yay sound control is working, thank you so much you're the best!
How to make this?
Hi AndroPlus,
I'm trying to figure out how one would go about building this boot.img that you've created.
What platform and compiler are you using?
Where are you getting sources the for the kernel? This file?
c9af6fc647060fb85dd646798453ec8f 23.0.A.2.105.tar.bz2
How do you construct boot.img from zImage + recovery?
Sorry if these are dumb questions.
Edit: never mind, I figured this out.
http://developer.sonymobile.com/kno...evices/how-to-build-and-flash-a-linux-kernel/ contains most of the information I needed.
The arm version of gcc that ships with Ubuntu 14.04 worked fine - arm-none-eabi-gcc (4.8.2-14ubuntu1+6) - no need to track down any mystery binaries. I did have to make several modifications to the kernel source to get it to build. Interestingly, some of the cpufreq stuff contained code that was incorrect. Someone at Samsung needs to go look up what "sequence point" means.
The hardest part was figuring out how to turn the zImage + ramdisk into something I could boot.
This: https://github.com/sonyxperiadev/mkqcdtbootimg was the correct tool to use - again, no need to track down any mystery mkbootimg or dtbTool binaries.
Hope this is helpful to someone. As someone new to Xperia dev, I found most of the information out there worse than useless.
dear modders
i just want to say i overclocked my htc one m7 cpu from 1.7ghz to 2.1 GHZ
with a custom kernel called ElementalX-m7-22.3-Sense
is this save can the phone run this without any stability issue's or shall i downclock it to 1.9
i use M7_Sense7_artmod_10.0 rom Lolipop 5.0.2 with sense 7 cause this is the only one without any bugs like no sound when you got called or sms sound's no boot sounds
i fixed my boot sound anyway on this rom
so my question is wont my phone be fried by this overclock cause i saw in the aroma installer that it can be overclock till 3 GHZ
greets Rubenownz
Overclocking the CPU in any system usually results in 2 main things:
a. Significantly shorter battery life.
b. heating issues.
sometimes (less frequently) you might experience a crash and fc here and there.
So yeah, it won't be all rainbows and butterflies.
PS: you probably won't reap the benefits of your now overclocked CPU without an app like no frills CPU or kernel Aduitor. Your device's performance isn't just about its CPU frequency, there's the min Max frequency your system is allowed to utilize, the CPU governor, and the I/o scheduler..
and
PPS: don't and I repeat DO NOT go anywhere near 3 GHz.
good luck.
I'm runnimg 2.1 Ghz OC for over 2 years without any issues. I would like to note that 2.1 Ghz on Elemental was not too stable for me, so I ran that on 2.0 Ghz. Anyway - i don't have any issues with my kernel, no overheating, battery lasts 100% same as stock frequency, no reboots, everything works as it's ment to work. If you really want to run on that frequency, make sure you set your voltage table to match your CPU clocks. Undervolting is not a good idea on such high clocks, so you might want to raise your voltages for higher frequencies a bit
monrokhoury said:
Overclocking the CPU in any system usually results in 2 main things:
a. Significantly shorter battery life.
b. heating issues.
sometimes (less frequently) you might experience a crash and fc here and there.
So yeah, it won't be all rainbows and butterflies.
PS: you probably won't reap the benefits of your now overclocked CPU without an app like no frills CPU or kernel Aduitor. Your device's performance isn't just about its CPU frequency, there's the min Max frequency your system is allowed to utilize, the CPU governor, and the I/o scheduler..
and
PPS: don't and I repeat DO NOT go anywhere near 3 GHz.
good luck.
Click to expand...
Click to collapse
ok mate
yeah i could raise also min clocks might turn that a noch up
just was wondering if it was possible without any harms
there are now on 384mhz 1 core is always active and 3 others are sleeping aid64 tells me
the temps are now 29 celcuis for 2.1 ghz
donkeykong1 said:
I'm runnimg 2.1 Ghz OC for over 2 years without any issues. I would like to note that 2.1 Ghz on Elemental was not too stable for me, so I ran that on 2.0 Ghz. Anyway - i don't have any issues with my kernel, no overheating, battery lasts 100% same as stock frequency, no reboots, everything works as it's ment to work. If you really want to run on that frequency, make sure you set your voltage table to match your CPU clocks. Undervolting is not a good idea on such high clocks, so you might want to raise your voltages for higher frequencies a bit
Click to expand...
Click to collapse
yeaah the kernel has those options in aroma installer it set it safe i ques
ill post later some picture's of what ive been doing
good nites
here are some pictures of my sense 7 5.0.2 android system dump of htc one m9 for htc one m7 xD overclocked
some temps and cpu tweaks and ofc of the system (dont mind about the girl on the screenshot its my girlfriend not me iam a boy
btw i removed phone number on call menu cause it's private
Greets Rubenownz