Related
A few weeks ago when I still had my HTC Hero it was overclocked to 672Mhz (standard = 528Mhz). It gave me a little boost in performance on Froyo, also the batterylife wasn't decreased too much.
But with our N1 running on 1Ghz, will it give much difference when clocked to 1113/1152Mhz? And what about batterylife?
If SetCPU is used what are your settings then? Mine is currently running on stock speed, no SetCPU.
ZeppeMan said:
A few weeks ago when I still had my HTC Hero it was overclocked to 672Mhz (standard = 528Mhz). It gave me a little boost in performance on Froyo, also the batterylife wasn't decreased too much.
But with our N1 running on 1Ghz, will it give much difference when clocked to 1113/1152Mhz? And what about batterylife?
If SetCPU is used what are your settings then? Mine is currently running on stock speed, no SetCPU.
Click to expand...
Click to collapse
I have my nexus one rooted and flashed to MIUI Rom and clock @ 690mhz I get way better battery power. Before I would only get 6hr to 8hr if lucky now I get from 9hr to 13hr depending how much I use it.
set to 1.13 ghz
then screen off to minimum 245mhz
josemedina1983 said:
I have my nexus one rooted and flashed to MIUI Rom and clock @ 690mhz I get way better battery power. Before I would only get 6hr to 8hr if lucky now I get from 9hr to 13hr depending how much I use it.
Click to expand...
Click to collapse
So you underclocked it, what about the speed? It's not to laggy?
Nexus one can run reasonably smooth @ 600mhz and above. It might not open applications as fast as it will be @ 1GHz though.
i think 1Ghz is enough for n1
why do u want an overclock?
Sent from my Nexus One using XDA App
shreyas1122 said:
i think 1Ghz is enough for n1
why do u want an overclock?
Sent from my Nexus One using XDA App
Click to expand...
Click to collapse
I didn't said I want an overclock. It's allready very fast on 1Ghz (compared to my old Hero ), just wanted to know your thoughts about overclocking the N1.
im overclocked at 1152 mhz and profiles set for 245 max with screen off. Overclocking is nice because i like the snappiness but most people cant tell the difference between 998 mhz and 1152. its not needed to overclock but i think profiles help alot. just my two cents
Ok thx, I will try 1150Mhz and see (if it's stable and) what batterylife does. I'm also going to try underclocking.
I have my N1 only for a couple of weeks now and I must say, this phone is awesome. It's VERY fast compared to my old Hero. I remember when I was installing apps on my Hero it became very slow and couldn't do anything untill installing was finished. With the N1 you still can do things while installing apps without lag. The responsiveness and smoothness is also a lot faster. I loved my Hero Because it never let me down, ok it was all a bit slower, but it was getting there. Now with the release of Gingerbread (custom ROM) it became to slow for me and that's why I sold my Hero and bought the N1. It was very difficult to find one, because of the EOL (end of life). But eventually I found one and i'm very happy with it. The N1 is allready more 1 year old, but it still competes with the best phones out there.
I generally run overclocked at 1075MHz, which gives a good balance between battery power usage and processor power. My understanding is that a different voltage scaling method is generally used above 1075MHz, so power consumption will increase above that point.
Didn't knew the voltage would increase above 1075Mhz, will keep that in mind
ZeppeMan said:
Didn't knew the voltage would increase above 1075Mhz, will keep that in mind
Click to expand...
Click to collapse
This is, of course, dependent upon how the kernel is constructed, but this is what I have generally found to be true.
Give us some feedback
I overclocked it too 1075Mhz when screen is on (screen off 245Mhz). Will give my thoughts in a day or 2.
Just report that my battery drain is almost the same as on stock settings. I think it drains a tiny bit faster on 1075Mhz, but nothing major. On the other hand, I don't feel it's faster on 1075Mhz then on stock speed. Only benchmarks give me performance increase.
I'm now on CM6.1.1 with stock kernel (cyanogen), I tried other kernels like Wilmonks kernel,.. Although it was more responsive, battery was going down even faster. I get best battery results with stock kernel.
Hard to choose
more speed = more battery drain
less speed = longer battery
I think I stay with the last option (less speed = longer battery), because Wildmonks kernel doesn't give me enough performance increase over the stock kernel on stock speed.
I have mine at 998mhz, but overclocked 1152 while plugged into power.
Either way, its so easy to play with the clock settings, i'd just have a play with a bunch of different settings if i were you.
liam.lah said:
I have mine at 998mhz, but overclocked 1152 while plugged into power.
Click to expand...
Click to collapse
I'd love a how-to fire that..
mind sharing the app?
Sent from my Nexus One
ZeppeMan said:
wanted to know your thoughts about overclocking the N1.
Click to expand...
Click to collapse
well my thoughts: underclock!
so you can watch movies on it all night!
Sent from my Nexus One
shreyas1122 said:
I'd love a how-to fire that..
mind sharing the app?
Sent from my Nexus One
Click to expand...
Click to collapse
You can use SetCPU to create profiles based on different circumstances.
Me, I have mine clocked to a max of 1075 and min of 245 with the screen on, 576 max / 128 min screen off, 998/128 charging (to reduce heat - overclocking while power is applied can make it silly hot), and a failsafe to clock down to 576/128 if the temperature gets over 50*C.
Fabulous app.
Correct me if I am wrong. When you use setcpu to "ondemand", the CPU speed can ramp up to max whenever necessary, otherwise the speed will tune down to min especially in standby mode. In that way, you can enjoy the advantages of overclocking and underclocking the CPU speed i.e. increasing performance when needed and saving power when not in use, right? When I loaded Rod's MIUI and Wildmonk's kernel, I can underclock down to 128Mhz and overclock up to 1.152Ghz. At the end of the day, I still have over 60% of power left after not so heavily use (some web browsing, checking email and listen some music). Overall, setcpu is a great app for me.
I have a question: why I can't overclock my SGS past 1.2 ghz. When I try to set for example 1.3 or 1.4 it freezes and I take out the battery in order to make it work again. Is there something I do wrong, is it a general problem with more SGSs? If somebody can , I really appreciate. Thanks
it is a kernel thing.
the kernel has to support those frequencies.
Sent from my GT-I9000 using XDA Premium App
I tried with tegrak overclocking with voodoo kernel (the application itself doesn't need a kernal that supports those frequencies) and with Supe Optimized Kernel (1.4 ghz) and voltage control and setcpu and is the same result:freezing.
Not every cpu is capable of stable overclocking past a certain threshold. You have probably hit the max speed your cpu can maintain.
I agree with you but then why there are other people with the same phone as me that can overclock them at 1.4 ghz?
With CM7 or miui and either bilboa or zacharius kernel you can overclock to 1300 but I haven't found a kernel that allows 1400 either, I think those that are doing it are hacking the CPU settings themselves.
My phone gets really hot at 1300 running apps like dungeon defender so 1400 might just be a bit too much
Sent from my GT-I9000 using XDA App
I am using Darky's 9.3 ROM but my problem is that i can't even touch 1300 mhz because my phone freezes.
Maybe a dumb question, but, do you overvolt as well as overclock? Maybe the cpu isnt getting enough juice?
Sent from my GT-I9000 using XDA App
Mirasdad said:
Maybe a dumb question, but, do you overvolt as well as overclock? Maybe the cpu isnt getting enough juice?
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
+1... not sure if there is much benefit at all to undervolting.. it just seems to make it immediately less stable...
can someone shed some light?
I've seen someone test this on another forum somewhere, and the difference the undervolting makes to the battery length is negligible..
kickassdave said:
+1... not sure if there is much benefit at all to undervolting.. it just seems to make it immediately less stable...
can someone shed some light?
I've seen someone test this on another forum somewhere, and the difference the undervolting makes to the battery length is negligible..
Click to expand...
Click to collapse
The principles of ovetclocking a PC also aplly to phones. Undervolting reduces the power available to the CPU. Undervolt a little and you'll save a little power. Undervolt.too much and the CPU won't get enough power to do basic functions hence freezing.
Every CPU has a limit to which you can over clock. You can overvolt to a point but then then the CPU reaches its limit.
From what I understand (read in another post) the hummingbird processors are not suited to overclocking. Where the arm such as that in the Motorola milestone clock really well. (You can oc a 600mhz milestone to 1ghz before you start seeing instability)
Hope this helped.
Sent from my GT-I9000 using XDA App
I understand the intention of undervolting as i am pretty good with PCs. Got my good old i7 overclocked constantly. But undervolting on the SGS has yet to show me any definitive advantages.
Sent from my GT-I9000 using XDA App
Cyanogen 8? Is this next? Or is this in the works? Also is 2.3.5 next and would it be numbered a different version when Ice Cream comes out? Also is anything coming from the devs to overclock to 800 yet?
cell2011 said:
Also is anything coming from the devs to overclock to 800 yet?
Click to expand...
Click to collapse
It's been done. So very very few phones are even stable at 800, and those that could generally performed worse in benches at 800 than at lower clocks. Many of these devices bootloop above 700.
Cyanogen 8 will not come out yet since will most likely be ice cream sandwich. I am not even sure is 2.3.5 will even come out and no the devs can not overclock this device to 800mhz because is 768 is the limit of the processor. Most people's phones do not even run that smoothly at 768 anyways. If somehow the dev found a way to overclock it to 800 (impossible btw but this is just a what if kind of statement) since the processor can not handle 800 it would just overheat the thing and cause crashes.
Also, on a side note, this should not be in the Development section. This should be in general or Q&A
This belongs in Q&A for future reference.
CM8 will be next, obviously. It will be based on Ice Cream Sandwich, so no, it won't be in development until ICS is released to AOSP so that the CM team can start using that code. 2.3.5 is an update coming out soon for the Nexus S 4G that fixes wifi and network speed, as well as adding more secure NFC for Google Wallet. It won't really affect us when it is merged into CM7. ICS is expected to be Android 4.0, but it could be 3.5 if Google decides.
There is a kernel that goes over 800Mhz, but anything over 768Mhz can be unstable on some phones. I tried it and there were no real performance gains, but battery life was a lot worse. Performance was actually worse at the highest CPU clock, in my experience. Just stick with 768Mhz. It's stable and chances are that you can get even better performance at a lower clock. I get better battery and performance at 633Mhz. It all depends on each unique phone.
rizdog23 said:
Cyanogen 8 will not come out yet since will most likely be ice cream sandwich. I am not even sure is 2.3.5 will even come out and no the devs can not overclock this device to 800mhz because is 768 is the limit of the processor. Most people's phones do not even run that smoothly at 768 anyways. If somehow the dev found a way to overclock it to 800 (impossible btw but this is just a what if kind of statement) since the processor can not handle 800 it would just overheat the thing and cause crashes.
Click to expand...
Click to collapse
I lol'd at this statement. Did you not read any of the posts above you?
When i began to post there were no posts yet. They must have got posted while i was typing. So seeing as the only post at the time was the op, then yes i did read the post(s) above mine.....
There is a kernel that goes over 800Mhz, but anything over 768Mhz can be unstable on some phones. I tried it and there were no real performance gains, but battery life was a lot worse. Performance was actually worse at the highest CPU clock, in my experience. Just stick with 768Mhz. It's stable and chances are that you can get even better performance at a lower clock. I get better battery and performance at 633Mhz. It all depends on each unique phone.
Click to expand...
Click to collapse
I can confirm that the Godmode kernel was able to push some phones, such as mine, past 800Mhz. Although I had a faster processor speed, my battery would drain incredibly fast as well as overheat. Even though I never hit a bootloop with the kernel, the battery life, overheating, and loss of performance kept me away. Sacrificing too much for having a faster processor speed. Normally I overclock to about 729Mhz and have great battery life, speed and performance in conjunction with a min of 19Mhz and a smartass governor.
Sent from my Hero that never dies! ;D
dastin1015 said:
I can confirm that the Godmode kernel was able to push some phones, such as mine, past 800Mhz. Although I had a faster processor speed, my battery would drain incredibly fast as well as overheat. Even though I never hit a bootloop with the kernel, the battery life, overheating, and loss of performance kept me away. Sacrificing too much for having a faster processor speed. Normally I overclock to about 729Mhz and have great battery life, speed and performance in conjunction with a min of 19Mhz and a smartass governor.
Sent from my Hero that never dies! ;D
Click to expand...
Click to collapse
Thanks. I am glad someone at least confirmed it. I never knew about the godmode kernel as ive only been here for a little bit. Sorry for misinformed post about their not being an 800mhz kernel. As I can see, i was wrong, but also I was correct in saying that the processor can not handle it....sometimes
rizdog23 said:
Thanks. I am glad someone at least confirmed it. I never knew about the godmode kernel as ive only been here for a little bit. Sorry for misinformed post about their not being an 800mhz kernel. As I can see, i was wrong, but also I was correct in saying that the processor can not handle it....sometimes
Click to expand...
Click to collapse
Yup, I'm at 806 - 19 ondemand while posting this and I can already feel it slowing down a little. 729 - 19 on demand is my best setup. I've tested a lot with trying higher setups than that but so far 729 seems to be the best for battery life and performance on every rom I've ever tried
Sent from my HERO200 using XDA Premium App
rubyknight said:
Yup, I'm at 806 - 19 ondemand while posting this and I can already feel it slowing down a little. 729 - 19 on demand is my best setup. I've tested a lot with trying higher setups than that but so far 729 seems to be the best for battery life and performance on every rom I've ever tried
Sent from my HERO200 using XDA Premium App
Click to expand...
Click to collapse
For some reason my phone never works well with higher clock speeds no matter what rom or kernel i use. I get my best results at 710-352 performance.
In before bierce gives birth over ANOTHER question being in the dev section
Sent from my Android using Tapatalk
rizdog23 said:
For some reason my phone never works well with higher clock speeds no matter what rom or kernel i use. I get my best results at 710-352 performance.
Click to expand...
Click to collapse
Correct me if I'm wrong, but from what I've noticed is that newer Hero's that were sold with Eclair as opposed to the original Donut, when I bought mine, are not able to reach those higher processor speeds past 691Mhz.
Sent from my Hero that never dies! ;D
i bought mine at radio shack back in september and it was still on 1.5 and ive never been able to get over 768mhz without it freezing and bootlooping its different with every hero.
i stay at 352-691 ondemand and thats plenty fast for me
Mine was running 1.5 also and it will run fine at 768 but battery life suffers so I usually run at 352/710 and battery and performance are good (depends on rom kernel)
Where can I get the godmode kernel ....
Sent from my HERO200 using XDA App
I actually got mine two weeks after it came out.....so i mean it could just be that this phone is dead now. I never had a refurb or anything. I got it wet once but it got repaired. I've only had this one the whole time. Do you think that is the issue?
rubyknight said:
Yup, I'm at 806 - 19 ondemand while posting this and I can already feel it slowing down a little. 729 - 19 on demand is my best setup. I've tested a lot with trying higher setups than that but so far 729 seems to be the best for battery life and performance on every rom I've ever tried
Sent from my HERO200 using XDA Premium App
Click to expand...
Click to collapse
Hey rubyknight,
just wondering why 19? Ive seen people do that but can the processor really ever do anything at 19? if so, doesnt it affect stuff like wake. Im trying it now just to see for myself. Ive been playing with a really high min value between 480 and 576 with the high at 748 and it actually doesnt only seems to affect battery life a little, both on the .29 and .35 kernels on jaybobs roms and on OMFGB.
Thanks
chalan30 said:
Hey rubyknight,
just wondering why 19? Ive seen people do that but can the processor really ever do anything at 19? if so, doesnt it affect stuff like wake. Im trying it now just to see for myself. Ive been playing with a really high min value between 480 and 576 with the high at 748 and it actually doesnt only seems to affect battery life a little, both on the .29 and .35 kernels on jaybobs roms and on OMFGB.
Thanks
Click to expand...
Click to collapse
It depends on the cpu governor that you use.
nandroids are for
sissies
ch1naski said:
It depends on the cpu governor that you use.
nandroids are for
sissies
Click to expand...
Click to collapse
so update, ive run it at 19/768 on demand all day and after 11hrs 13 min its at 60% thats not bad for my phone! and there was almost no performance difference. Just the slightest UI lag... this is on jaybobs 7/8 with the .29 kernel, with background data off. And my regular usage which is not a lot. but for me its good. i wish I had tried it ages ago.
chalan30 said:
so update, ive run it at 19/768 on demand all day and after 11hrs 13 min its at 60% thats not bad for my phone! and there was almost no performance difference. Just the slightest UI lag... this is on jaybobs 7/8 with the .29 kernel, with background data off. And my regular usage which is not a lot. but for me its good. i wish I had tried it ages ago.
Click to expand...
Click to collapse
I believe that you can set the ramp up frequency and that may help with the lag. Setcpu, advanced settings, I think?
nandroids are for
sissies
Welcome to the Thrillz kernel for LG Thrill 4G (may be compatible for O3D).
Standard disclaimer: You bork, your phone. I take no liability. K?
Includes OC to 1.2 native (no modules) and 100 MHz frequency.
cifs.ko module built in.
Conservative governor enabled.
init.d support native.
More to come.
V2 update includes:
Insecure boot
persistent root shell in adb
Removed 100 MHz frequency (caused more issues than it was worth)
Trying a 200 MHz frequency.
V3 includes:
Lock 200mhz when sleep (was set at 300, swapped due to removal of 300)
---Working on other improvements, may be a week or two due to cleanup of code and removal of non-4430 chaff---
V4
Updated frequencies (300, 600, 800, 1000, 1300)
Lower cpu voltages.
#Note, seems screen is eating more battery than CPU. Will investigate.#
Plan for V5
More governors, possible UV compatible with Xan's Voltage Control app.
If you have suggestions, ideas, please give me them.
I do plan on more governors (maybe smartass, interactive, ect....) more io schedulers (bfq, ect...) and anything else that comes my way.
Special thanks to those who have gone before me and helped my learn what I have: gtg465x, LinuxBozo, and Entropy512 for everything that I've learned from them in the Infuse 4G forums, Excaliburinhand for encouraging me to start my own kernel, CallMeAria, Urabewe, tylerwagler and gtg465x again for what they've done here before me... and to you for choosing this kernel (I know... Video game cheezy, but it's true. )
Git is below, it is under the wagler kernel git as it was what I forked and am pushing to. I decided it's time to get started with this.
And please remember, thanks button is good as is fueling my insanity. If you look at my Infusion kernels, I do recognize my "Insanity Crew." (and if you want to be kept in obscurity, I respect that as well. )
Good job man, everyday this forum gets better.
...fighting ninjas at night. Talking about this and that.
Work pretty good on o3d l'll check battry life let u know later
Sent from my LG-P925 using XDA App
Thanks! Keep the comments and suggestions coming! (hoping for p920h/p925 GB leak and official GB source for p920, but I'm fully supporting this in the mean time. Forward ho!)
So far this is best kernel for my rom (v10kv4) so far I got best mobile speed 1.6up 5down i never got this speed any rom or kernal before best speed i had before 1.5. &4 from thriller
Sent from my LG-P925 using XDA App
I hate to report that my battery life did not impress me at first but after charging it seems to be doing better. But i was losing about 15% every 3 hrs in idle. No wifi data or anything.
Sent from my LG Thrill 4G...
Good to see you guys pushin' the kernel movement forward, and sharing your work.
Good deal on getting that built in overclocking going as well. I've been running the kernel for the past day. I did notice an issue, though. Maybe it's just my phone... But the 300mhz OPP, is not being utilized.
I've attached some screenshots.
I was planning to mention that, will try to fix. (100-300 bug) on battery life, what governor are you running? I've found better life on conservative or on demand.
my battery life is decent not the best try to calibrating battery will give you a decent battery life
bedwa said:
I was planning to mention that, will try to fix. (100-300 bug) on battery life, what governor are you running? I've found better life on conservative or on demand.
Click to expand...
Click to collapse
Usually I'm in hotplug or performance... My device has no service, so it doesn't see "normal use" like most. Most of the time it just sits and sleeps.
So, what I did yesterday, really because I wanted to see if you guys squashed the random reboots I've notice in my own playing with LG's kernel source... Had a fully charged phone, flashed your kernel, ran a few benchmarks, still had over 90%, and just let it sit in hotplug. got back to checking it out maybe 12 hours later, noticed the drain, checked setcpu, and that explained it for me. My phone normally would be 80% to 90% in 300mhz... But I don't think 100mhz is able to accomplish most tasks, so it's always popping out, even when it should be idle sleeping.
One thing for me is wireless tethering.. The device needs to be able to accomplish this in the background, and 300mhz even on a DroidX is able to accomplish this. 100mhz is a no go, though.
If you find it real difficult to get 300mhz functioning with 100mhz, I'd say chop the 100mhz out for now, and give us a bump, or atleast put out a 'high voltage' 1388000 mV(TI's kernel 3.0 number) top slot version of the kernel... The overclock module still works with your kernel, BTW... So, in combination with the voltage bump, those that are real speed freaks can push toward that 1300mhz mark with stability.
P.S. No random reboots, so that gets a big thumbs up!!!
I'm going to try and keep to 5 freqs, going to see if 200 works. If not 300 will be low end. Wanting to see if 1.4 or 1.5 is possible with proper voltage. (we should reach sgs II performance benches at that level. )
bedwa said:
I'm going to try and keep to 5 freqs, going to see if 200 works. If not 300 will be low end. Wanting to see if 1.4 or 1.5 is possible with proper voltage. (we should reach sgs II performance benches at that level. )
Click to expand...
Click to collapse
hehehe twould be pretty nice to rub in the face of the acclaimed best device..
Running new Kernel now, so far seems to be running smooth, max 1200, min 600 on Performance governor
Trekfan422991 said:
hehehe twould be pretty nice to rub in the face of the acclaimed best device..
Click to expand...
Click to collapse
It would be nice but I have yet to see my Thrill out perform my STOCK SGS2 yet with any kind of tweaking.
I only hope it can be done.
sent from my Stock Samsung Galaxy S II
I think I got an issue. Starts to lagg when typing/texting. Maybe its the governor I used. I tried with both concervative and ondemand. Also hotplig too. Conservative had the least amount of lag but still noticeable. The other 2 were way too laggy. Unusable.
I believe that's due to the 100 MHz freq. I rebuilt later night without it and while I am typing this there is no lag for me. Re-uploading V2.
Anyone flashed this can comment on battery life and any issues?
Haven't had it long enough for battery use, but it made slim doomed speedier.
Sent from my LG-P925 using xda premium
Flashed it. So far no lag. Battery life kinda iffy. But it's a brand new battery. I'll clear the stats and see how battery life is then.
No issues, phone feels really fast, more batt drain though. I like it.
Sent from my LG-P925 using XDA App
hey everybode!
i wanted to know i have rocket rom and i want to use setcpu to overclock my kernel
and sebastian is max to 1400 is thers good kernel that i can play with it till 1700mghz or 1900?
but it need to be stable
Abyss goes to 1700. My CPU can't take it, sadly
bubu23 said:
but it need to be stable
Click to expand...
Click to collapse
The stability is dependant on your hardware; some chips can only overclock to 1500Mhz and some can overclock all the way to 1900Mhz. It is not something the kernel has a say over.
Don't all of the notes have the same cpu? Why can some be overclocked and others not?
Sent from my GT-N7000 using Tapatalk
kkg720 said:
Don't all of the notes have the same cpu? Why can some be overclocked and others not?
Click to expand...
Click to collapse
They all can be overclocked, but how much is a different thing altogether. It's quite simple really, not every chip manufactured is of equal quality; some chips have more imperfections. The more imperfections the less it can be overclocked before it becomes unstable. It's the same thing as on PCs, too.
Stable is it when you do nothing and use it in originally form. Overcklocking need more Power more power is less time you enjoj your note!
Generally these chips are made to tolerate a certain speed, and because of variability, the manufacturer drops the speed tolerance to ensure overall quality. Some will still be able to manage 1500, 1700, or even 1900 (although rarely, I'd say). Just about all of them tolerate 1400, so very few are defective at the stated tolerance. With 5 million, you will get a few, however.
This is one of those rare occasions when statistics have a benefit in the real world!
jeromepearce said:
Generally these chips are made to tolerate a certain speed, and because of variability, the manufacturer drops the speed tolerance to ensure overall quality. Some will still be able to manage 1500, 1700, or even 1900 (although rarely, I'd say). Just about all of them tolerate 1400, so very few are defective at the stated tolerance. With 5 million, you will get a few, however.
This is one of those rare occasions when statistics have a benefit in the real world!
Click to expand...
Click to collapse
I will keep mine at stock speeds because ignorance is bliss
bubu23 said:
hey everybode!
i wanted to know i have rocket rom and i want to use setcpu to overclock my kernel
and sebastian is max to 1400 is thers good kernel that i can play with it till 1700mghz or 1900?
but it need to be stable
Click to expand...
Click to collapse
There are many out there that will let you overclock. Search the Android development forum.
Like most, I have flashed heaps of times, probably at least four or five times a week when I first got this wonderful Note, but in the last month or so have only been tempted to stray three or four times. Personally Franco 6 is best for me, because I favour battery life and stability rather than overclocking (1400MHz is not bad as a standard!!)
I would encourage you to try a few for a few days, as long as you backup often you should have a great experience!
Are all kernels capable of overclocking?
Is there one that overclocks the best?
How do you tell how high you can go?
Do you jusy keep overclocking until the NOte stops working?
If so, there must be a fine line.
jeffs99 said:
Are all kernels capable of overclocking?
Is there one that overclocks the best?
How do you tell how high you can go?
Do you jusy keep overclocking until the NOte stops working?
If so, there must be a fine line.
Click to expand...
Click to collapse
Stock kernel isn't capable of overclocking.
One way to tell is to download things like SetCPU which detects the range of the clockspeed. Another way is to simply read the description of the kernel thread.
How high your phone can go is an individual thing. You need to overclock in slight increments (say 50mhz at a time) and run a stability test to see if the phone crashes or not.
You DO NOT pull the slider all the way to 1.9 ghz and "see" if anything happens. If you fry your CPU, do not come to us for help.
This is why I don't like overclocking, it's a waste of time to run the stability tests, etc.
In summary, you need to raise it a little bit, and run stability tests and repeat the process until your phone crashes. At that point, you'd know the last safe-stable clockspeed that your CPU can take.
PoisonWolf said:
Stock kernel isn't capable of overclocking.
One way to tell is to download things like SetCPU which detects the range of the clockspeed. Another way is to simply read the description of the kernel thread.
How high your phone can go is an individual thing. You need to overclock in slight increments (say 50mhz at a time) and run a stability test to see if the phone crashes or not.
You DO NOT pull the slider all the way to 1.9 ghz and "see" if anything happens. If you fry your CPU, do not come to us for help.
This is why I don't like overclocking, it's a waste of time to run the stability tests, etc.
In summary, you need to raise it a little bit, and run stability tests and repeat the process until your phone crashes. At that point, you'd know the last safe-stable clockspeed that your CPU can take.
Click to expand...
Click to collapse
Thanks!
What do you recommend for a good stability test?
I'm on franco.kernel v10 and OC to 1600 using Tegrak. Tegrak runs the stability tests automatically and reverts to stock 1400 if unstable or a reboot occurs.
I tried 1700 but Note rebooted after about 2 minutes. Booted right back up at 1400 with no problems. Re-set to 1600 and running smoothly.
kraz
Sent from my Beautiful, White GT-N7000 using xda premium
Set CPU has a CPU stress test
Sent from my GT-N7000 using xda premium