In normal running mode ODIN sees the Cappy, but when I switch to download mode it doesn't see it any more. I am trying to put my phone back to factory default so I can install CM7 but running into all kinds of problems. I did get the base system reinstalled using a One Click JAR that I found here on XDA. The phone seems to be ok with that.
ADB doesnt think there are any devices attached either when I am in download mode.
I did also try the Heimdall install methods and used their drivers, but that doesnt work either
All I am trying to do so far is get CWM installed
Any ideas?
Did you ever use Heimdall?
MarkWorsnop said:
In normal running mode ODIN sees the Cappy, but when I switch to download mode it doesn't see it any more. I am trying to put my phone back to factory default so I can install CM7 but running into all kinds of problems. I did get the base system reinstalled using a One Click JAR that I found here on XDA. The phone seems to be ok with that.
ADB doesnt think there are any devices attached either when I am in download mode.
I did also try the Heimdall install methods and used their drivers, but that doesnt work either
All I am trying to do so far is get CWM installed
Any ideas?
Click to expand...
Click to collapse
If you used a one-click jar file, I believe you used Heimdall, as Odin-based one-clicks would be .exe files. That being the case, if one of the one-click heimdalls worked, other ones should work as well.
If you don't mind me asking, which one-click did you use? What rom were you on when the other one worked, and what rom are you on now?
I installed this "SamsungCaptivate-SGHi897-UCKB2-Rooted-One-Click.jar" to get it to work in what I think is a factory default.
I am now trying to get the downloading to be recognized by Odin or Heimhall or anything/.
They all see the phone in normal mode but when in download they do not see it
Have you tried all of the USB ports on your computer? If you're on a desktop, make sure it's one of the ones in the back (directly attached to the motherboard). Also, if you haven't rebooted your computer, do that, and then see if the UCKB2 one-click sees your device.
You can also try the full heimdall package, as that has a tool that will quickly check to see if it sees a device in download mode.
ODIN doesnt see Cappy
Looks like the drivers from Heimhall mess up the ODIN drivers. I removed the drivers from System Drivers that the Heimhall installed and now the ODIN seems to see the device again.
Now I need to figure out what I need to put on the device to make it work
MarkWorsnop said:
I installed this "SamsungCaptivate-SGHi897-UCKB2-Rooted-One-Click.jar" to get it to work in what I think is a factory default.
I am now trying to get the downloading to be recognized by Odin or Heimhall or anything/.
They all see the phone in normal mode but when in download they do not see it
Click to expand...
Click to collapse
einstall the Samsung drivers. The zadig driver you installed for Heimdall causes problems with dl mode if you then try to use Odin.
mrhaley30705 said:
einstall the Samsung drivers. The zadig driver you installed for Heimdall causes problems with dl mode if you then try to use Odin.
Click to expand...
Click to collapse
I just figured this out. Now what CWM file does ODIN want? After all of this I am lost! I will start back at the first post on adding CWM I guess...!!
It's going to want a kernel with CWM baked into it, or you can flash the JF6-based one click file to get back to stock without the 3e recovery error. From there you can just root, then copy the rom you want to install to your internal SD card. Rename it "update.zip", and flash that.
If memory serves me correctly, that's the simplest way to flash from Eclair. You can also try to Odin in a CWM-friendly Froyo kernel, or copy the cwm file out of the AIO captivate toolbox (copy it out, don't directly use the tool).
To get cwm, use a kernel with cwm as jimtheiss said, in a tar format. Older Talon kernels were in tar, as was Speedmod, and I think xcal's reoriented kernel had a tar version.
Open Odin, use the pda slot for the kernel, uncheck reboot. Connect phone. When the yellow box lights up, hit start. When completed, pull the battery,reinsert battery, use button combo to get in recovery.
jmtheiss said:
It's going to want a kernel with CWM baked into it, or you can flash the JF6-based one click file to get back to stock without the 3e recovery error. From there you can just root, then copy the rom you want to install to your internal SD card. Rename it "update.zip", and flash that.
If memory serves me correctly, that's the simplest way to flash from Eclair. You can also try to Odin in a CWM-friendly Froyo kernel, or copy the cwm file out of the AIO captivate toolbox (copy it out, don't directly use the tool).
Click to expand...
Click to collapse
I can't seem to find Eclair with CWM. I did find a I897UCJF6-final-OCD-REV0 EXE with ODIN built into the EXE but whatever happens on that version ODIN didnt see the phone.
The ODIN 1.85 sees the phone, but I do not know what to download and what there downloaded file goes in ODIN.
I also ran the JAR file again and it did get back to 2.2 but then I dont seem to be able to get CWM working.
All I wanted to do it put CM7 on the phone. I guess I have to have Eclair or Froyo first to get the CM7? I think that is what I read. I havent tried it from GB
I would suggest following mrhaley's directions about flashing the kernel.
And here is the speedmod kernel.
MarkWorsnop said:
I can't seem to find Eclair with CWM. I did find a I897UCJF6-final-OCD-REV0 EXE with ODIN built into the EXE but whatever happens on that version ODIN didnt see the phone.
The ODIN 1.85 sees the phone, but I do not know what to download and what there downloaded file goes in ODIN.
I also ran the JAR file again and it did get back to 2.2 but then I dont seem to be able to get CWM working.
All I wanted to do it put CM7 on the phone. I guess I have to have Eclair or Froyo first to get the CM7? I think that is what I read. I havent tried it from GB
Click to expand...
Click to collapse
My 2 cents....if you have so much difficulty using Odin/Heimdall, I would highly recommend staying away from CM7 or MIUI until you are really comfortable flashing stuff without hiccups. CM7 and MIUI are quite different beasts, compare to the ROms ur flashing.
chappatti said:
My 2 cents....if you have so much difficulty using Odin/Heimdall, I would highly recommend staying away from CM7 or MIUI until you are really comfortable flashing stuff without hiccups. CM7 and MIUI are quite different beasts, compare to the ROms ur flashing.
Click to expand...
Click to collapse
The only thing he needs to flash with Odin/Heimdall is the kernel to get cwm. Its the same for most other GB roms. After you get cwm, its just flashing from cwm, with an extra factory reset and ROM flash.
Related
Looking in the About phone area it says my Kernel is 2.6.29 [email protected] #2 which i'm assuming isn't a stock Kernel. I can't get into download mode or recovery to save my life. Any good ways to get it back? Everything I've tried doesn't work. I'm curious about this android sdk adb access thing but I haven't been able to search about it. Thankfully my phone works right now but the only way i know how to flash stuff it through the key method.
Any links to a tutorial about this adb thing? ALso, where to download the android-sdk?
Thank you thank you thank you!
wrong section
WRong thread but dont wanna flame... : D
This happens some time, just flash this and you will have 3 button recovery again.
EDIT: STUPID ME, just realized you cannot get into recovery... Well use ADB to get into Recovery then flash that
Android SDK - http://developer.android.com/sdk/index.html
Make sure u have Java JDK installed! - http://www.oracle.com/technetwork/java/javase/downloads/index.html
Sorry idk about a good ADB tutorial though
That is a stock kernel.
1. This is a stock kernel
2. Which 3-button combo did you try? It can be either +-USB or -Power
amtrakcn said:
1. This is a stock kernel
2. Which 3-button combo did you try? It can be either +-USB or -Power
Click to expand...
Click to collapse
I can't get into download mode or recovery mode. I've flashed quite a few different roms since i've had this phone and never had a problem. For some reason this time when I went from MikeyMike01's GR-12 2.3.3 back to stock with Odin3, I lost the ability to use my volume buttons + power to go anywhere. I was trying to install CWM to put Serendipity 6.4 on my phone because the other one was having some weird issues.
Thanks to everybody else for the links I'll try them when I get home... work is blocking the android sdk download website. I'll update in a bit with success (hopefully).
If all else fails, you could extract the 3 button fix posted above, and odin.
No buttons working? Pull batt, open odin, insert usb, reinsert bat, and it should go into download mode..
illavbill said:
Looking in the About phone area it says my Kernel is 2.6.29 [email protected] #2 which i'm assuming isn't a stock Kernel. I can't get into download mode or recovery to save my life. Any good ways to get it back? Everything I've tried doesn't work. I'm curious about this android sdk adb access thing but I haven't been able to search about it. Thankfully my phone works right now but the only way i know how to flash stuff it through the key method.
Any links to a tutorial about this adb thing? ALso, where to download the android-sdk?
Thank you thank you thank you!
Click to expand...
Click to collapse
skip all that .... if it boots upto OS and you just have no 3 button..... Use This
http://forum.xda-developers.com/showthread.php?t=944418 and flash 3 button with it. Access to recovery or dl mode not needed. Just be sure to follow the instructions with the tool. It works. Simple.
Moved to proper forum.
illavbill said:
Looking in the About phone area it says my Kernel is 2.6.29 [email protected] #2 which i'm assuming isn't a stock Kernel. I can't get into download mode or recovery to save my life. Any good ways to get it back? Everything I've tried doesn't work. I'm curious about this android sdk adb access thing but I haven't been able to search about it. Thankfully my phone works right now but the only way i know how to flash stuff it through the key method.
Any links to a tutorial about this adb thing? ALso, where to download the android-sdk?
Thank you thank you thank you!
Click to expand...
Click to collapse
before i tell you an easy way to get into recovery, was this odin "oneclick" or did you have to add a .tar file to a "PDA" slot and perhaps a .pit file and others? this is highly important because 3-button fix only flashes the secondary bootloader. if you still have 2.3.3 bootloaders this will brick the phone! there needs to be an update to the 3-button fix to flash both bootloaders. a quick test if you have 2.3.3 bootloaders is if the phone says "galaxy s gt-i9000" you may have 2.3.3 bootloaders on the phone. on 2.3.3 this screen is part of the bootloaders as well as the param.ifs, flashing 2.1 without the bootloaders will show the i9000 splash before the att param.ifs splash
if it was odin oneclick you are safe to flash a 3-button fix. if it was odin full you may still be on the 2.3.3 bootloaders and dont have button combos due to some incompatablility with the phone, i saw this once. please use odin oneclick first then see if it still needs 3-button fix.
if you need to reflash with odin "oneclick"
look up "adb" make sure you know how to manually install drivers. there are links in posts above
if you did flash with oneclick then you can also root and use rom manager to reboot into recovery. then flash 3-button fix via update.zip. search dev section for designgears' 3-button fix, there is a update.zip version.
why do u need the three button here...just hold down the volume key and the power button to get in to the recovery. worked for me.
Dani897 said:
before i tell you an easy way to get into recovery, was this odin "oneclick" or did you have to add a .tar file to a "PDA" slot and perhaps a .pit file and others? this is highly important because 3-button fix only flashes the secondary bootloader. if you still have 2.3.3 bootloaders this will brick the phone! there needs to be an update to the 3-button fix to flash both bootloaders. a quick test if you have 2.3.3 bootloaders is if the phone says "galaxy s gt-i9000" you may have 2.3.3 bootloaders on the phone. on 2.3.3 this screen is part of the bootloaders as well as the param.ifs, flashing 2.1 without the bootloaders will show the i9000 splash before the att param.ifs splash
if it was odin oneclick you are safe to flash a 3-button fix. if it was odin full you may still be on the 2.3.3 bootloaders and dont have button combos due to some incompatablility with the phone, i saw this once. please use odin oneclick first then see if it still needs 3-button fix.
if you need to reflash with odin "oneclick"
look up "adb" make sure you know how to manually install drivers. there are links in posts above
if you did flash with oneclick then you can also root and use rom manager to reboot into recovery. then flash 3-button fix via update.zip. search dev section for designgears' 3-button fix, there is a update.zip version.
Click to expand...
Click to collapse
I used Odin oneclick to reset it to stock. I've been moving this weekend so I just left the phone on 2.1 but today at work i'll try the method you mentioned above. I didn't even think about rom manager to reboot to recovery i'll try that first. I was trying to reboot the phone into recovery so I could install CWM. Sounds easier than the other methods.
ive tried so many of all of your roms and cant find the answer for this. i just came back from being on a gingerbread rom (simply honey) and i tried going to toxic music but tokic got stuck for 20 minutes on the bali kernel screen. now i cant get into the recovery option (reinstall packages) so i can root. it wont let me. it says no such file or directory. ive done this about 60 times and never came across this problem. i cant get root access to add other roms. can someone please point me in the right direction...PLEASE!
Wrong place! But gb roms have a diff method for getting into download mode
Sent from my SGH-T959 using XDA Premium App
Did you install GB Bootloaders?
Edit: Read OP wrong
childspsongs said:
ive tried so many of all of your roms and cant find the answer for this. i just came back from being on a gingerbread rom (simply honey) and i tried going to toxic music but tokic got stuck for 20 minutes on the bali kernel screen. now i cant get into the recovery option (reinstall packages) so i can root. it wont let me. it says no such file or directory. ive done this about 60 times and never came across this problem. i cant get root access to add other roms. can someone please point me in the right direction...PLEASE!
Click to expand...
Click to collapse
Yep. This certainly will occur after coming from gingerbread. Load up Odin and flash back to stock, reroot your phone as you normally would. Flash a 2.2 kernel and a 2.2 modem and try to flash. Its seems like you might have some Ginger Ghost left from gingerbread rom and its causing conflict coming back to 2.2 or 2.2.1. Are you able to get in download mode? If so you'll be ok.
Saxysaxplayer said:
Did you install GB Bootloaders?
Edit: Read OP wrong
Click to expand...
Click to collapse
That's what I'm thinking...
deleted post
I did use gb bootloaders. Please point out where the print modem and kernel are please. I already am on stock. And I can get into download mode fine. Thank you guys. I know im not inthe right thread but you guys are the right people.
childspsongs said:
I did use gb bootloaders. Please point out where the print modem and kernel are please. I already am on stock. And I can get into download mode fine. Thank you guys. I know im not inthe right thread but you guys are the right people.
Click to expand...
Click to collapse
go into download mode and odin to stock
http://www.youtube.com/watch?v=l3K9my9kAvI
you will use same files but different key combination to get into download mode...
That key combination is vol up+power for download mode...at least I'm pretty sure.
jcc332006 said:
Yep. This certainly will occur after coming from gingerbread. Load up Odin and flash back to stock, reroot your phone as you normally would. Flash a 2.2 kernel and a 2.2 modem and try to flash. Its seems like you might have some Ginger Ghost left from gingerbread rom and its causing conflict coming back to 2.2 or 2.2.1. Are you able to get in download mode? If so you'll be ok.
Click to expand...
Click to collapse
that is the problem though. I can get to download mode. I can go back to stock. I can download the root file. I can go to recovery . ....but I can not load it. red typing comea up when I try to reinstall packages and it says It cant install from sd. how can I obtain root if I cant load it from recovery? Can I use odin for your music rom? I just need root. Killing myself trying to figure this out.
Did you put the update.zip on the root of your SD. or in some other file.?
That is also my suspicion. You probably don't have the update.zip in the main directory of your phone's sd card. If its not there, you can simply transfer it back in via usb...
that was it. i had a file called rootupdate.zip and i thought that was the one but i guess it wasnt because nothing was happening. so i looked again in my external sd and still had the original update.zip file, transferred it and it worked. happily rooted again! thank you guys for your help. maby i should delete this thread now.
Instead of rooting JFD and flashing CWM just flash a voodoo+stock kernel. you'll have cwm faster than rooting then getting cwm
philliple97 said:
Instead of rooting JFD and flashing CWM just flash a voodoo+stock kernel. you'll have cwm faster than rooting then getting cwm
Click to expand...
Click to collapse
is there a stock voodoo kernel .tar though ??
cant flash without root
Hey guys... ok i have been looking and cant seem to find how to rectify this issue... i am really stuck and would appreciate any help possible..
Ok so i had stock 2.2 on my captivate, n tried to install a gingerbread rom using mobiletechvideos easy step guide using this link
http://www.youtube.com/watch?v=UOyx5JQ_8_I
... in doing that the first step of installing the bootloaders through odin, i inserted the pda files but it freezes at setup connection... now i think its soft bricked as i can still put it in download mode.. the thing is i have tried one click odin to revert back to 2.1 or 2.2 but it stops at set pit file... and then do not turn off target... its been here for over 25 mins n nothing... i have kept trying a couple of times and sometimes it wud just say fail.. Guys again i am sorry if this in the wrong place or has been brought up before.. i tried looking and was not able to find anything..
Thanks
Well your first issue there he says flash to stock 2.1 jf6 you where on 2.2 Unless your phone is a newer build 2.1 is always better to flash then 2.2. What build is your phone?
Reboot your computer, swap usb ports to one that is in the back attached to the motherboard (if already back there swap to a different one in the back) or port #1 on a laptop. Right click odin and run as administrator.
Thanks for the responses..
Yeah i know it said do it on 2.1, i figured it cud have worked on 2.2 i guess i was wrong... n in terms of switching port, odin still recognizes the port as i get the yellow screen but it doesn't move from there...???
It doesn't matter what's on the phone 2.1, or 2.2. **** you can be in a custom rom (I made the jump from firefly). If you are using odin its the same, if it will write 2.1 over anything why wouldn't do it for 2.3.3? No Difference.. The only way 2.2 would matter is if you weren't using odin then you would have to get around 3e recovery. But download mode is underneath the firmware does not matter what is on it odin will overwrite it.
And odin can be super touchy with the usb ports. And although it sees it the flash fails if odin is on the rag and didn't take any midol.
studacris said:
It doesn't matter what's on the phone 2.1, or 2.2. **** you can be in a custom rom (I made the jump from firefly). If you are using odin its the same, if it will write 2.1 over anything why wouldn't do it for 2.3.3? No Difference.. The only way 2.2 would matter is if you weren't using odin then you would have to get around 3e recovery. But download mode is underneath the firmware does not matter what is on it odin will overwrite it.
And odin can be super touchy with the usb ports. And although it sees it the flash fails if odin is on the rag and didn't take any midol.
Click to expand...
Click to collapse
again thanks for your help studacris... so basically if odin can read it but nothing happens i am screwed... i really need to know if there is absolutely anything else i can do to fix this as this is my only means of communication.. i am lost without my cappy...
Are you sure you are using a Motherboard usb port and that you are running on Admin? If odin is being stupid you can look in to Heimdall
prbassplayer said:
Are you sure you are using a Motherboard usb port and that you are running on Admin? If odin is being stupid you can look in to Heimdall
Click to expand...
Click to collapse
yeah i am sure i am using it on the motherboard port and running it on admin.. It basically freezes on differnt areas and doesnt completely reflash to stock on odin3 one-click downloader...
So there is nothing else i cud do with odin rite??
rheanjd said:
yeah i am sure i am using it on the motherboard port and running it on admin.. It basically freezes on differnt areas and doesnt completely reflash to stock on odin3 one-click downloader...
So there is nothing else i cud do with odin rite??
Click to expand...
Click to collapse
Try a different version of odin. If that dont work then use Heimdall
You can go to samfirmware.com-US SGS download wich ever version u want (id use JF6) download and decompress. Each .md5 file you need to decompress as well and get out the individual file in them. Here is a good how too with heimdall from mobiltechvideos. Hope this helps
prbassplayer said:
You can go to samfirmware.com-US SGS download wich ever version u want (id use JF6) download and decompress. Each .md5 file you need to decompress as well and get out the individual file in them. Here is a good how too with heimdall from mobiltechvideos. Hope this helps
Click to expand...
Click to collapse
Thanks.. i was hoping odin wud have come through but i guess i will have to try heimdall...
Ok guys i have downloaded heimdall and right now trying to install the jf6 2.1 rom... the thing is i am on load package and tyring to put the firmware package... this might be a stupid question but i am inserting the zipped file but it keeps saying - Tar header contained an invalid file size... Do i need to extract the files and then do this..???
rheanjd said:
Ok guys i have downloaded heimdall and right now trying to install the jf6 2.1 rom... the thing is i am on load package and tyring to put the firmware package... this might be a stupid question but i am inserting the zipped file but it keeps saying - Tar header contained an invalid file size... Do i need to extract the files and then do this..???
Click to expand...
Click to collapse
Wich Heimdall you using? I suggest 1.1.1 in wich you choose each file u want to flash individually.
i had downlaoded 1.3.0 will try this thanks..
ok so i have inserted factory fs, kernel,param,cache,database data,modem and clicked start, it took two seconds and then stated failed to retrieve config descriptor...??
also i haven't added anything in the pit or primary and secondary and recovery files
rheanjd said:
ok so i have inserted factory fs, kernel,param,cache,database data,modem and clicked start, it took two seconds and then stated failed to retrieve config descriptor...??
also i haven't added anything in the pit or primary and secondary and recovery files
Click to expand...
Click to collapse
Im not sure about your error but the Jf6 from samfirmware has FactoryFS, Param.lfs, Cache, Database Data, Modem and Recovery(Zimage). Maybe you put a file in the wrong place?
Thanks but istn't the zimage supposed to be for the kernel... i haven't inserted anything into the recovery field...
i am rite now left clueless
No your right. Its the kernel I had a brain fart. Well I honestly Do not know whats wrong, Im assuming you ran Heimdall as Admin... Well **** man any way you have access to another machine? Im out of ideas maybe someone else can help. =/
Hey thanks i really appreciate the help ...
guys if anyone else can help me out it would be really appreciated... the phone is all i got and i really need it to work today... i am just restarting my computer and will try again hopefully it will work otherwise i am out of options...
Ok restarted and giving the same issue...
"Failed to retrieve config descriptor"
what the hell is that???
so my dilemma is as follows.. i was running continuum 4.1 on my captivate. i decided i wanted to try one of the new gingerbread roms, so my first step was to use odinoneclick 1.0 to get to complete stock and go from there. my luck, odin froze on me at sbl.bin... so i am soft bricked but i can use the vol up/down plug usb method to get to download mode. because i have only used one click before, and not a full odin like 1.7, i am having trouble figuring out exactly what i need, and what steps are necessary to safely get me back to stock using odin 1.7 so i can then load GB bootloaders and stop messing with BL's from now on.. so i suppose my main question is should i first flash eclair before trying to flash GB bootloaders/rom? my other question being, if so, what files do i need, and do i need to place a pit file and repartition? sorry if this is a noob question, i just dont want to screw it up any further and wasnt sure if specific steps must be taken when you are soft bricked.. thanks very much in advance!
No need to flash Eclair. Just flash the KF1 file in this post and then XCal's reorient for GB and you'll be good to go. Just don't boot into the OS after flashing XCal's kernel else you'll get bootloops since it was designed for I9000 based ROMs rather then I897. Just reboot back into recovery after flashign XCal's Kernel and then flash whatever GB ROM you want.
http://forum.xda-developers.com/showthread.php?t=1126704
I personally prefer to flash my phone using Heimdall on my laptop running Kubuntu as it's generally more stable/successful, and it's easier to choose which files you want to flash if you only want to flash specific files (Like the bootloaders).
Also KH3 is out and it looks like it might have updated bootloaders, but it's not a full ROM from what I was able to grab. It's missing the param.lfs, dbdata.rfs, and the pit file. Also has an added SS_DL.dll which I'm not sure what the purpose of that file is since it's a Windows file...
http://forum.xda-developers.com/showthread.php?t=1232703
Moved to Q&A.....
NO QUESTIONS IN DEVELOPMENT PLEASE!!!!!
conantroutman said:
Moved to Q&A.....
NO QUESTIONS IN DEVELOPMENT PLEASE!!!!!
Click to expand...
Click to collapse
my apologies! my intention was to post in q&a but i was at work sneaking on the pc i must have been clicking too fast..
and kyuta... thank you for the suggestion! so is it safe to just use the whole odin package in the link you provided just to get a clean install, and then move on to a rom/kernel of choice at a later time?
im getting a big red FAIL on every attempt at flashing KF1 file with odin 1.3 and 1.7 im not sure which route to take at this point. do i need to flash the pit file with the bootloaders?
dartdc97 said:
im getting a big red FAIL on every attempt at flashing KF1 file with odin 1.3 and 1.7 im not sure which route to take at this point. do i need to flash the pit file with the bootloaders?
Click to expand...
Click to collapse
just make sure u hav right file downloaded...and right click on odin and click run as administrator...try changing the usb ports....and try changing the usb cable...and see if u hav proper driver installed ....
check all these which i hav mentioned...
then u shd be able to go back to either eclair(jf6) or gingerbread(kf1) stock
killer_raj said:
just make sure u hav right file downloaded...and right click on odin and click run as administrator...try changing the usb ports....and try changing the usb cable...and see if u hav proper driver installed ....
check all these which i hav mentioned...
then u shd be able to go back to either eclair(jf6) or gingerbread(kf1) stock
Click to expand...
Click to collapse
Just to add this this: Try using XP service pack 2 mode if you are using Windows 7 x 64.
Similar to Masterslackers issue.
The phone was originally a stock Optus Éclair 2.1. About 6 months ago I decided to customize the i9000 with a custom Froyo 2.2.1 Rom (Doc's Rom Docs_XWJS3_Wipe-v9_1) from “The ROM Kitchen”. It worked really well and was much faster and responsive..
Yesterday, I decided to look at a move to Gingerbread and cook another ROM @ the ROM Kitchen, this time a Gingerbread 2.3.4 iteration.
The phone was rooted so I used Rom Manager to get into recovery mode where I could flash my new, Doc's JVR_No_Wipe-v8-00-08-22-10-09-4e6a8e4e86718.zip Rom.
All seemed to go well, but after the Flash, as the phone booted the first screen became filled with 100s of random coloured lines, then it transitioned to the normal Samsung start animation, but soundless.
After booting, I noticed that I no longer had a notification bar where battery, time, signal strength etc. was normally displayed atop the screen. I tried several different launchers to see if that was the issue, but to no avail. I tried to enable the notification bar using Go Launchers gesture setting (no go)
I tried rebooting the phone over and over, the notification bar would not return.
I was starting to lament my decision to flash when the following occurred.
I tried to re-enter recovery mode via ROM Manager to install a different ROM, but the phone bypassed it and then hung @ the Samsung I9000 logo screen. I then had to power the phone off before it would reboot into its UI. I could no longer reach recovery mode by any means.
Because I was getting nowhere and I had read that after flashing a new rom, root would often be lost, so I tried rerooting with "XXJVP-Complete-Rooting-Package" from
http://androidadvices.com/how-to-root-galaxy-s-on-android-2-3-4-xxjvp-firmware/ This also failed but it has also left me with a soft bricked phone.
The phone will not boot up or boot into recovery now, however It would still boot into (3 button) download mode.
I have tried various versions of Odin from v1.0 to v4.28 to ReFlash the phone back to life but with no success yet.
Using Odin, the phone hangs with no sign of progress and reports the following when left for 30minutes or so.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
Anyone have any suggestions that might help to get the phone back.
Thanks, TeZ
So you didn't flash stock gingerbread before flashing custom rom? so you should first flash stock jvr and do hard reset after booting. Then you are safe to flash cwm capable kernel and custom rom.
For the odin problems, maybe you have kies running in background? Kill all kies processes and try again.
And I'd suggest reading all guides found in romkitchen thread..it saves lots of trouble. Hope that can fix your phone
Sent from my GT-I9000 using xda premium
Agree with above post, if you have Klies on your pc/laptop uninstall it, and re download the drivers, i have a good 2.3.4 tutorial and root 2.3.4 tutorial, both with Odin, let me know if interested. Also if you have heimdall installed then uninstall it also.
After you unistalled Kies (or at least stop it) and installed the drivers , pick a stock rom with bootloader from Ramad collection http://forum.xda-developers.com/showthread.php?t=1102881 .
I prefer Odin 1.82.
If you still unable to flash your phone, please follow steps from this guide to see how can debrick your phone.
http://forum.xda-developers.com/showthread.php?t=1134975
Good luck
Thanks for that, I did install kies after I bricked it, in the hope (probably missguided) that it would somehow help. Uninstalling
bigmadpete said:
Agree with above post, if you have Klies on your pc/laptop uninstall it, and re download the drivers, i have a good 2.3.4 tutorial and root 2.3.4 tutorial, both with Odin, let me know if interested. Also if you have heimdall installed then uninstall it also.
Click to expand...
Click to collapse
Thanks for your input, right now i need all the help I can get, hadn't heard of heimdall before. I guess its one more thing I could try if all else fails. But right now I'm going to try a few more conventional things with odin, like flash a stock rom etc.
DSGE said:
After you unistalled Kies (or at least stop it) and installed the drivers , pick a stock rom with bootloader from Ramad collection http://forum.xda-developers.com/showthread.php?t=1102881 .
I prefer Odin 1.82.
If you still unable to flash your phone, please follow steps from this guide to see how can debrick your phone.
http://forum.xda-developers.com/showthread.php?t=1134975
Good luck
Click to expand...
Click to collapse
Your post looks promising, I'm going to try this method out and see where it leads. I'll reply back with the outcome, many thanks
No problem. Try this option if you like http://www.theandroidsoul.com/xxjvp-android-2-3-4-firmware-galaxy-s-install-and-download/
And then this to root
http://www.theandroidsoul.com/root-xxjvp-firmware/
bigmadpete said:
No problem. Try this option if you like http://www.theandroidsoul.com/xxjvp-android-2-3-4-firmware-galaxy-s-install-and-download/
And then this to root
http://www.theandroidsoul.com/root-xxjvp-firmware/
Click to expand...
Click to collapse
Thanks for the info, running out of time today, will try for tomorrow
When moving from a froyo (2.2) rom to gingerbread, (2.3), you need the gingerbread bootloaders or you'll get all sorts of crap when turning on your phone (ie what you have).
Use odin to flash back to froyo, or flash a gingerbread firmware that comes with bootloaders. (I would recommend going back to froyo first to make sure everything is ok, since flashing bootloaders is a bit risky, as messing it up can permanently brick your phone)
cobrasixtysix said:
Thanks for your input, right now i need all the help I can get, hadn't heard of heimdall before. I guess its one more thing I could try if all else fails. But right now I'm going to try a few more conventional things with odin, like flash a stock rom etc.
Click to expand...
Click to collapse
DSGE said:
After you unistalled Kies (or at least stop it) and installed the drivers , pick a stock rom with bootloader from Ramad collection http://forum.xda-developers.com/showthread.php?t=1102881 .
I prefer Odin 1.82.
If you still unable to flash your phone, please follow steps from this guide to see how can debrick your phone.
http://forum.xda-developers.com/showthread.php?t=1134975
Good luck
Click to expand...
Click to collapse
Ok, here's where I'm at:
For the sake of simplicity I will detail what gave positive results rather than a tirade of what didn't.
Uninstalled Kies, rebooted
As instructed, went to:
http://forum.xda-developers.com/showthread.php?t=1102881
downloaded: Odin v1.82
downloaded: Gingerbread 2.3.3 (Australia and New Zealand)
XWJVN/XXJVQ/XSAJV5/Sbl (CSC: XSA): Download (150 MB) (Build date: Sun Jul 10 11:30:54 KST 2011)
Loaded up Odin and followed instructions.
Flash went ahead as normal and I now have a working phone again, thanks to you DSGE, I'm a very happy man
So I now have Gingerbread 2.3.3 installed and running.
My only issue's now is, that.
1. Half my apps dont work now or force close even after a reinstall.
2. Some apps won't install at all IE; my fav launcher; Go Launcher
3. I no longer have root access so Rom Manager and Titanium backup wont work.
4. My Backup Pro, works after I rewrote the correct path to the External Sd, but do I want to do that just yet? and just how much data should I reinstate so I don't corrupt the new system?
What should I do now?
Install busybox?
do a hard reset?
Flash a different Rom that will work for me?
Thanks so very much for all the good advise.
Cheers
First root the phone, then either a different rom, or format system and re install 2.3.3 or which ever u just installed, i think ure apps are not working due to the phone needing a wipe/reset and cache cleared from clockwork recovery
bigmadpete said:
First root the phone, then either a different rom, or format system and re install 2.3.3 or which ever u just installed, i think ure apps are not working due to the phone needing a wipe/reset and cache cleared from clockwork recovery
Click to expand...
Click to collapse
OK, latest update:
Everything is working fine including all my progs.
Like you say, I just need to root it now.
Can you point me to the correct files to root?
Thanks
http://www.addictivetips.com/mobile...t-samsung-galaxy-s-i9000-with-a-single-click/
or
http://androidadvices.com/how-to-root-samsung-galaxy-s-gt-i9000/
Read carefully friend
bigmadpete said:
http://www.addictivetips.com/mobile...t-samsung-galaxy-s-i9000-with-a-single-click/
or
http://androidadvices.com/how-to-root-samsung-galaxy-s-gt-i9000/
Read carefully friend
Click to expand...
Click to collapse
Seems to relate to 2.1 to 2.2.1 didn't see any mention of 2.3.3. I'm afraid I'll stuff the phone if I use the old root files.