please help :/ think my phone might be bricked - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

i flashed darky rom 1.3 on my phone, ive been having some problems id get a lot of force closes and i wouldnt be able to call out when i do it would end the call after the first dial, id get no signal, id then get a force close, then signal would come back. so i went into cwm recovery. performed a full data wipe and tried to flash any other rom - rocket rom v12 and cassie xtra lite v5. on every type of rom i try even the kl7 stock deodexed, it just stays stuck on the samsung glaxy note gt n7000 screen and stays like that. for instance its been like that for the past 40 mins now at the side of me. i dont really know what to do, ive tried multiple data wipes inc dalveks cache. would flashing via odin help ? how do i do that. wondered if i could get some help guys.

Your phone is not bricked. Just entered a boot loop.
You just need to reflash an official firmware from Samsung, then you can flash a custom one over that. Be careful that zergrush or appropriate exploit is avaliable for the version of firmware that you will flash, you don't want to increase the binary counter
To enter download mode:
"Put your Galaxy Note in download mode. To accomplish this, power off your Galaxy Note and then power it back on while holding volume down and home button together with power key".

thanks for the reply, im a little rusty to flashing stock roms with odin i dont really know what to do, i have odin opened with all the necessary things checked, ive downloaded this http://forum.xda-developers.com/showthread.php?t=1412959 stock kl7 but i just get a md5 tar file, how do i get the pda etc, that is ODIN way of doing it am i correct ?
am i right in thinking i can just resent the binary counter with a jiig sometime down the line ?

darkyrom
i had same issue with same rom and i flashed overa stock rom
aaaaaaits this rom bud, my note doesnt like it, try sheep rom, ive found that the best one out of all of them.

Related

[Q] [kernel] speedmod captivate problems with flash

So i've been searching for a few hours while trying to flash my cappy with speedmod kernel for 5 hours...
I don't know whats wrong but I can never get passed the galaxy s screen right after the opening at&t world phone screen. I am able to go into recovery mode and go through features but every time I reboot or turn my phone on it never gets passed the galaxy s screen. it seems like the kernel is running fine but then it stops right after the opening at&t screen. what am i doing wrong???? I have been at this for too long.
Can someone please help me with my problem... I can't seem to find anything about this and a lot of people aren't having much problem flashing this kernel. why can't I be one of those people... please! if you can push me into the right direction, that would be great!
btw... it seems like its frozen on this screen but I don't think it really is.
how long does the first boot of a new kernel take? any adjustments in recovery mode that I need to make? I've also tried the older speedmod kernels and and I get the same problem. Am I using odin right, because I followed the speedmod tutorials word for word...
did you feel any vibration during your booting? like one vibration or three vibrations?
I don't think there was any vibrations upon booting. if there was I believe it was only one. I could be wrong though. at this point I don't even want to put a custom kernal on my phone. I've been at this for a long time and it seems like I haven't gotten anywhere.
which rom are you on?
im running stock everything but superuser permission root. stock kernal and what not also. I ended up using odin one-click downloader to flash back to stock. now my phone is back to stock and working.
the thing is that I want to flash speedmod on my phone but now I cant get into download mode or recovery mode. my phone is glitchy now too.
can you provide some suggestion on how to flash right? I would ask in the speedmod thread but Im a new to the threads and it wont let me yet.

[Q] Messed it up and need help

This WAS the situation before the problems:
Rooted Gingerbread rom, all working fine. Decided to unroot and install the full version of the official German ICS rom by using PC Odin. All went fine and used my Note for over two days. Because of the lags en slow responses I decided to reflash the ICS rom. From that moment on I messed it up. I've been reading and searching hundreds of posts for almost a day but didn't find a solution.
This IS the current situation:
I can get into download mode
I can get in recovery mode
However, in recovery mode I can not install a rom, every flash (CWM, both ICS and GB - even using chainfire's rom needed for rooting) stops on a random moment...but never gets it to the end, even if I wait several hours. Installing is very...very....very slow.
In recovery mode i can not restore a Nandroid backup, both ICS and GB. Every backup stops when /system has te be installed. errormessage.
In download mode I can connect my Note to PC Odin. I can select a rom and start flashing. However, after appr. 80% installation halts during "nand write start", no error message. The flashing does not finish, even after hours.
Funny is, i can install a kernel like Abyss.
So, I can't restore, i can't flash using cwm in recovery and I can't flash using PC Odin. My device seems not fully bricked. The max I get when rebooting (knowing that the process has not finished) is the triangle screen.
Any advise is appreciated.
Do not flash thru CWM... Flash a good GB kernel like "franco.Kernel" but thru PC Odin then u can flash whatever u want from franco's CWM... Good luck
Don't need help anymore
Note is officially bricked. After several attempts to recover from a softbrick the screen of my Note didn't turn on anymore. No button or button combination works, no recovery and no download mode, just a black screen.
Ce said:
Don't need help anymore
Note is officially bricked. After several attempts to recover from a softbrick the screen of my Note didn't turn on anymore. No button or button combination works, no recovery and no download mode, just a black screen.
Click to expand...
Click to collapse
Flat battery? It's also possible that it's just the screen that's not working. Try entering download mode "blind". So hold power+home+vol down for ~10 seconds, then press vol up. Hook it up via usb and see if Odin can recognize it.
Thanks, didn't think of that. But unfortunately no response from the device.
So now that it looks like your phone is officially bricked, I think you should just take it to Samsung and make up a story. Like you were updating your software with Kies and something happened and the phone is just not booting up.
I am sorry you bricked your note though..
try AMORA Filemanager.. flash via recovery and you have a file manager,,, take a look on your partitions
just my idea, you got nothing to lose
musashiro said:
try AMORA Filemanager.. flash via recovery and you have a file manager,,, take a look on your partitions
just my idea, you got nothing to lose
Click to expand...
Click to collapse
I would like to but it's very hard when you can't see anything on the screen...
Maybe it's just the battery, try to charge it externally and try a JIG also
Sent from my GT-N7000 using XDA
Just a quick, final, update.
My Note was superbricked. Had to send it to a Samsung Service Center. No additional questions were asked. Samsung replaced the mainboard. Didn't have to pay anything.
Great service!!!
try this out buddy, do it on your own risk!!! anyways you have messed it up.
Ce said:
This WAS the situation before the problems:
Rooted Gingerbread rom, all working fine. Decided to unroot and install the full version of the official German ICS rom by using PC Odin. All went fine and used my Note for over two days. Because of the lags en slow responses I decided to reflash the ICS rom. From that moment on I messed it up. I've been reading and searching hundreds of posts for almost a day but didn't find a solution.
This IS the current situation:
I can get into download mode
I can get in recovery mode
However, in recovery mode I can not install a rom, every flash (CWM, both ICS and GB - even using chainfire's rom needed for rooting) stops on a random moment...but never gets it to the end, even if I wait several hours. Installing is very...very....very slow.
In recovery mode i can not restore a Nandroid backup, both ICS and GB. Every backup stops when /system has te be installed. errormessage.
In download mode I can connect my Note to PC Odin. I can select a rom and start flashing. However, after appr. 80% installation halts during "nand write start", no error message. The flashing does not finish, even after hours.
Funny is, i can install a kernel like Abyss.
So, I can't restore, i can't flash using cwm in recovery and I can't flash using PC Odin. My device seems not fully bricked. The max I get when rebooting (knowing that the process has not finished) is the triangle screen.
Any advise is appreciated.
Click to expand...
Click to collapse
i was not a member when i commited this mistake. but then big thanks to this community it helped me back from softbrick.
first you do is install a stock kernel of ics on your note go into recovery and just clear cache partition, thats it no wipe/data factory reset.
then,
install the pit file from this thread, also read it completely before proceeding. http://forum.xda-developers.com/show....php?t=1667886 , hoping yours is 16gb version and also read this thread for additional info but its quite complicated for me so im just telling you the direct method and hopefully itll get your note back to work. so once you download the 16gb pit file unzip it and in the unzip folder you will find a separately lying pit of 16gb stating patched-standard thats the one you want.
then,
goto samfirmware and download the latest ics firmware(i downloaded the indian one as it is in file .tar),
unzip it till you get .tar file.
open odin- click pit-select 16gb patched standard pit- check wether repartion is ticked- click pda-select the .tar file you extracted connect your phone and start. this time i wont stop at factory.fs.....
NOTE THAT AFTER THIS PROCEDURE IS COMPLETED SUCCESSFULLY YOUR INTERNAL STORAGE WOULD BE ONLY 8GB INSTEAD OF 11 GB STOCK WHICH YOU WERE GETTING.
I REVIVED MY NOTE THROUGH THIS PROCEDURE. PROCEES AT YOUR OWN RISK.
one your phone is working you'll be able to reset the counter with a jig and get your phone under warranty and get your motherboard changed by teliing at the Samsung Service that you are getting only 8gb instead of 11gb you used to get earlier(warranty only if you had any).
hope this helps mate.
BEST OF LUCK!!
A BIG HUGE THANKS TO hg42.....

[Q] HELP!! Some Serious Captivate Issues!! PLZ Read

So basically I have a Samsung Galaxy S Captivate (i896) and it was running 2.1, so I decided to try and upgrade to the newest stock available for the captivate (which is 2.3.5). I had to use heimdall because I bought the phone used and it was rooted and possibly running a custom ROM so kies is not an option. When I put the phone in download mode the computer wouldn't recognize it (I'm on a Mac). I did alot of reading online and I couldn't find a solution. So I decided to flash a new ROM hoping that this would solve the problem.
So I flashed a random ICS ROM. But with this ROM I couldn't even access download mode. I tried a 3 button fix, I tried to use terminal to boot into download mode, and I tried to use ADB from my computer; nothing worked. So I figured I would flash another ROM (this time I used Hellybean) but when I tried to install it, a bunch of code ran on the screen and it said "installation aborted". Before attempting to flash this ROM I completely wiped the phone (i formatted the system from the mounts menu in CWM) and now the phone is showing the at&t logo, then going to black, then some code runs on the screen, then it goes black and starts the whole thing again.
I cant get to recovery or download mode.
Is it bricked? How do I fix this?
I don't know what I did wrong! any help would be appreciated.
P.s. I would really like to avoid building a jig because I feel like Im not too good at that kind of stuff....but if that's what it comes to...
Thanx in advance
All the information you need is already available:
Putting the Phone into Download Mode
How To flash ANY Captivate ROM from Stock
Val D. said:
All the information you need is already available:
Putting the Phone into Download Mode
How To flash ANY Captivate ROM from Stock
Click to expand...
Click to collapse
I've tried all of those methods except for using a jig. Is it possible that while flashing a ROM my phone somehow lost download mode?
Also if all of those combos didn't work is it likely that a jig will work?
Looks like you started reading after you messed up the phone. Update instructions say clearly that you need GB bootloaders before you proceed to ICS or JB. You provide no information what exactly ROM you started from, what GB ROM you attempted to flash (with or without bootloaders), what exactly ICS you flashed after, what "some code" runs on the screen now, etc. It's a lot of guessing here. If bootloaders are messed up, than you won't be able to fix your phone at home. I have never seen a problem you describe, so wait for someone with more experience to stop by.
I got it going! All it needed was a jig and then I was able to flash stock GB with bootloaders.
Thanks for the help.
Good news! :good:
I have a Cappy and gingerbread boot loaders come in three flavours i897, i896 and i9000 and they're backwards compatible with froyo and éclair roms. Don't mix froyo and gb boot loaders though you will hard brick your device. I have i896(Canadian) boot loaders and when I flash kk4 [email protected] Odin gingerbread my "i896" boot screen is garbled image of pixels until I flash the proper param.lfs file to match. Hope this helps. BTW I have a jig as well and for all galaxy devices it's a must.
Sent from a Borg powered Nexus 4

Rooted Note 1 in bootloop after update

Hi everyone. I have a rooted Galaxy Note 1. I accidentally tried to update something (the phone said there was an Android update or something) and now my phone in stuck in a bootloop showing the Android logo. When I try to reset it (volume+home+power buttons) it goes to an Odin "Downloading..." screen and gets stuck on that.
I've seen some stuff about unbricking the phone using Odin to return to the original stock rom. But from what I can tell, there are different stock roms available depending on your Country Sales Code (CSC). So apparently I need to look in Kies for my CSC to know which rom to download, but Kies doesn't recognise the phone, I guess because it's bricked. I know the phone is from the UK, but I don't know what network it came from (I bought it second hand). All I know is that it is unlocked now.
I have CWM.zip, CWM-SuperSU-v0.87.zip, and franco.Kernel-r5.zip on the micro SD card from when I was rooting it ages ago. Do these have anything to do with fixing it?
Any ideas on where I go from here? Thanks for your help.
Which volume button did you press ? You need volume up + home + power to get into recovery.
You can flash any rom from any region using odin.
Same problem
Hey,
Thanks for helping me in advance...
I used the Custom ROM (( http://forum.xda-developers.com/showthread.php?t=1970626 )) Ultimate N7000 for a long time. However this build became more and more unstable the longer I used my phone.
So I decided to go back to STOCK.
So I followed this guide: http://forum.xda-developers.com/showthread.php?t=1424997
And everything went well (Odin didnt give any errors)
However after reboot... the problem began... I cant turn my phone on anymore.... It seems to be stuck in a bootloop....
How can I fix this?? please help me
Which rom did you flash? If you flashed JB, boot into recovery and wipe data. Then reboot.

Soft brick?

hello,
my name is sunil and i am from india. i am using GT-i8190 since 2years n 8months, basically i know how to play with this custom roms and rooting things. because after one month of i bought this phone i was started to use customs. but before 8months since today. my phone get one sms and when i click to open the message. phone get hanged. i pull the battery and try to start my phone again. but its not even booting or displaying anything... i tried 10days to power it on. i loose my hope its gonna be on because it was totally dead. don't know what happened suddenly its getting power on. but since that day its not going thru the recovery mode which is twrp. if i flash anything via odin. it is the same bootlooping. i had flash so many times for old and new stock firmwares, stock kernels, custom roms, custom twrp, cwm... everything i have tired... even samsung service station is so so silly. they are saying to me for replacing board... so now what i have to do with this device? what is work on this phone right now is i can get in to the download mode.... i can see the samsung galaxy s3 mini logo for 20second. and then its start looping. if i flash anything... it wont get in to the device... its showing in odin that everything is pass and reset all img flies flashed... but when the flashing is started... one this happens in to the phone which is never ever happend before i was flashed... you know in odin mode there is 5 lines on the top of the screen. 1) in red font ODIN MODE. 2) Product name : GT-8190. 3) custom binary download : yes (15 counts). 4) current binary : custom and 5) system status : custom. now when i flash anything on my device for now. in the 4th raw where written current binary : custom... its going to be changed in something flie names and bytes in red font....
please help me out of this... i don't know what to do now? because i have tried all...
(MY ENGLISH IS POOR HOPE YOU UNDERSTAND MY PROBLEM)

Categories

Resources