[Q] Uh oh, I think I'm bricked, what should I do? - Galaxy Tab Q&A, Help & Troubleshooting

Hey all,
I was trying to Odin back to Stock Gingerbread on my Sprint Galaxy tab, after 20 ish minutes I noticed it was making no progress (flashing never takes that long) so for some stupid reason I decided to turn off the tablet by using the power button.
Now it won't turn on at all. I've tried holding the power button down for 10 minutes (nothing), volume down plus power button (nothing), touching the screen plus power button (also nothing).
I'm kinda terrified right now. Is there anything I can do?

Ok
Been here b4
Try this, run odin, then put tab in dl mode. I know there is no android guy digging on the screen but still plug the usb in. When this happened to me this is what I did out of desperation. It showed up in odin even tho the tab looked dead.
let us know if it works for you

What I mean buy put it in dl mode even tho it seems obvious is go thru the steps even tho the device seems unresponsive. Weird as it may be I could not find this answer with a search. But it worked!!! should be added to a sticky somewhere as I was looking at a dead azz unit with dizzmal hopes.

Related

[Q] I Actually Managed to Brick this Phone

Hey guys I think I actually did it. I was going to install the JPC Froyo Rom, and somehow booted into recovery in the ROM. Now whenever I turn the phone on it boots into recovery, and none of the button combinations work for putting it into Download mode so I can flash back to stock. On the i9000 thread it says that if you get into this situation you cannot flash back. Any of you guys run into this issue? If not then it looks like I'll be trying to convince an ATT rep to give me a new phone
Try powering off... Then hold vol up and down buttons then plug in usb.... That happened to me... Your not bricked
Sent from my SAMSUNG-SGH-I897 using XDA App
Connect to adb and run reboot command
Sent from my GT-I9000 using XDA App
Nope
Nope sorry guys I know all of what you just said. As for plugging in USB while holding volume buttons, it'll just go to that battery charging screen, and adb doesn't work because it doesn't boot past recovery. Sorry guys but yes it was bricked. It's okay though because I just went to ATT and since they can't identify the problem they just replaced the phone
Thought mine was bricked one night, too. Same scenario. Tried dropping the SIM and SD card out even though I didn't think it would make a difference, but it did. Got to download screen and reflashed with ODIN.
Good luck.
Sent from my SAMSUNG-SGH-I897 using XDA App
KCutrer1 said:
Nope sorry guys I know all of what you just said. As for plugging in USB while holding volume buttons, it'll just go to that battery charging screen, and adb doesn't work because it doesn't boot past recovery. Sorry guys but yes it was bricked. It's okay though because I just went to ATT and since they can't identify the problem they just replaced the phone
Click to expand...
Click to collapse
If you pull the battery, then put the battery in. hold both volume buttons buttons, and then plug the phone into the computer, it didn't boot to download?
Im curious if you even tried to use the Odin one click thread
There are 4 or 5 ways in that thread on how to get to download mode. And how exactly does this relate to development...just another curious thought. Well, you are getting a new phone, just hope that ATT or Samsung don't try to figure out the cause of your phone being "bricked".
AGAIN!
Okay after this I swear I won't be messing around with Froyo anymore. Here's the story: I got into download on the replacement captivate. Tried to install JPC froyo, but it never started flashing so I unplugged it from Odin and then tried to turn it back on. It goes to the normal "connect phone to computer" screen. However no attempts to get back into download mode have worked. Holding both volume buttons and power until second black screen doesn't work, booting while holding volume down doesn't work, holding both volume buttons and then inserting USB cable doesn't work. I think I'm stuck in this screen unless there's some incredible way I have yet to try. Anybody have any ideas? I would greatly appreciate feedback from the experienced users (Zilch25, designgears, kaik, reaver117), because I think I'd be pushing it trying to get it replaced a second time in such rapid succession
To flashman2002:
I put it in this section because it's in the development section that most flashing and such occurs so I thought there would be the greatest knowledge base. And yes I've pored over the one click thread and none of the methods mentioned there have any effect!
Jeez, I just scared the **** out of myself. I ran the remove lagfix script and it rebooted my phone but it was just a black screen. So I take the battery out. Bad Idea. It showed the ATT screen but just black after that. I could get it into recovery mode but not download. Then I messed some more and would only show a vague disconnected pic.
Finally I got it into download by doing this: (had odin open before hand)
1. took everything out including sim and usb cable.
2. quickly inserted battery and held volume buttons and very quickly inserted usb.
I'm pretty sure its the speed that matters because I tried about 4 times and only when I did it really fast did it work.
ThisWasATriumph said:
Jeez, I just scared the **** out of myself. I ran the remove lagfix script and it rebooted my phone but it was just a black screen. So I take the battery out. Bad Idea. It showed the ATT screen but just black after that. I could get it into recovery mode but not download. Then I messed some more and would only show a vague disconnected pic.
Finally I got it into download by doing this: (had odin open before hand)
1. took everything out including sim and usb cable.
2. quickly inserted battery and held volume buttons and very quickly inserted usb.
I'm pretty sure its the speed that matters because I tried about 4 times and only when I did it really fast did it work.
Click to expand...
Click to collapse
Nope. Unless you can do this with godly speed I dont think it'll work. I just got to the "Connect Phone to Computer" screen again.
You had the usb in before anything appeared on the screen right?
ThisWasATriumph said:
You had the usb in before anything appeared on the screen right?
Click to expand...
Click to collapse
Yeah originally. I can get to that screen now by just putting the battery in and holding power button. It seems to behave exactly like it normally would, just can't get out of it.
What screen? The screen you want has a big yellow triangle and says download.
ThisWasATriumph said:
What screen? The screen you want has a big yellow triangle and says download.
Click to expand...
Click to collapse
No it's on the phone...!...computer screen. That's what I'm saying, it's been stuck here for a while and none of the methods described on the one click thread work. I've been here before and just holding volume buttons and holding down power for it to boot twice and releasing would do it. Not so anymore. Can't get into download mode doing anything!
Well I read In the SRE thread I think that there are reports of newer phones not responding to any button combos. Bad batch they said not on purpose...
Also for the i9000 apparently you only have to hold the down volume key so since you flashed a i9000 rom try that if you haven't already.
You cant get into recovery right? Just holding volume and power then letting go of power after a bit?
Adb reboot download...
Sent from my SAMSUNG-SGH-I897 using XDA App
ThisWasATriumph said:
Well I read In the SRE thread I think that there are reports of newer phones not responding to any button combos. Bad batch they said not on purpose...
Also for the i9000 apparently you only have to hold the down volume key so since you flashed a i9000 rom try that if you haven't already.
You cant get into recovery right? Just holding volume and power then letting go of power after a bit?
Click to expand...
Click to collapse
Nope none of it works. I just got it replaced less then 3 hours ago and I already bricked it. I hope somebody finds out something that'll get this fixed. Maybe some way to force download mode through a computer application or something.
Well theres adb like mentioned above but im pretty sure that requires at least recovery mode working.
Like i said before i was stuck on the same screen so maybe theres still hope.
If all else fails someone will figure out how to JTAG these things eventually...
ThisWasATriumph said:
Jeez, I just scared the **** out of myself. I ran the remove lagfix script and it rebooted my phone but it was just a black screen. So I take the battery out. Bad Idea. It showed the ATT screen but just black after that. I could get it into recovery mode but not download. Then I messed some more and would only show a vague disconnected pic.
Finally I got it into download by doing this: (had odin open before hand)
1. took everything out including sim and usb cable.
2. quickly inserted battery and held volume buttons and very quickly inserted usb.
I'm pretty sure its the speed that matters because I tried about 4 times and only when I did it really fast did it work.
Click to expand...
Click to collapse
I know it doesn't help you out now, but when you remove the lag fix, just leave it set on the black screen. It's doing its thing. It will reboot when it's done. The home keys should still light up if you press them in this state...
Well thanks for your input anyway guys. Hopefully somebody figures something out. For now I guess I'll keep the SIM in my old iPhone 3G so I at least have a phone. Tomorrow I'll go to another ATT store in my area. Chances are the rep won't know what the hell that screen means and will replace the phone promptly.

[Q] Boot Brick

Okay I was using odin one click it was at rebooting device after it completed pushing stock onto the phone thats when I discounted the usb.... should have waited two secs I know but now the phone doesn't seem to get past the att world phone screen keeps looping over and over I have tried all the key combos different times and ways, vol up and down being held doesn't get to download mode the screen remains black plunging in seems to get to charge mode where even plunging into the wall charger it loops trying to calculate the battery status... any method I haven't tried... I did get it to boot once full and was usable didn't think to redo odin at the time and restarted back to this mess...tried three different jigs using the 100k 5% X3 even through its not a full brick due to the button combos gotten no where. Please Help
Search the forum to build a jig in order to get into download mode. Or you may need to buy one just in case in the future.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139
Try this:
Open Odin and plug your cable into your computer but not your phone yet
Pull battery on phone and put it back in
Hold both volume buttons down and then plug your phone in
It should go into download made and you can reflash the stock ROM
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
norcal einstein said:
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
Click to expand...
Click to collapse
Ahah Thats the same exact steps I was able to get the phone to boot that one time instead of the up down I was still attempting it to get past the loop holding the power button instead using those steps, if I had know it would have been one of the only times I would see it in there I would have pushed it to download with adb though...
can't test getting it to download mode now took it back fit the description of the standing on/off issue with the device still honored by warranty. And I wouldn't have posted without searching everywhere to make a jig, I made three of them though I noticed it still didn't get to download mode. I made sure that the last two jigs were done correct. Think that when it was disconnected from odin it wasn't done finalizing after the stock push gah >,< live and learn and do something else to the cappies XD.
Thanks for the link placing an order just in-case ~whistles looking around then side to side pushes another rom~ lalala
To offer my own advice if it ever happens again, what I've been able to do is:
1. Pull the battery out
2. Put it back in
3. Open Odin
4. Hold Both Volume Buttons (without holding the power button)
5. Plug the phone back in
It went immediately into download mode for me, Odin managed to time out several times while I was trying to flash a co-worker's Captivate to the official Froyo leak. One of those times I couldn't even get the phone to come up with any screen. I really do think this thing cannot be bricked.
BeowulfShaeffer said:
That has been my experience so far, too. I've "bricked" twice, once with an "all black" screen, and once with the phone-!-computer screen. I've yet to need a jig, though I thought I may have needed it last night when I got the "all black" screen.
Keep trying the different button press methods to get into download mode. It took me 4 attempts to get from "all black" to "phone-!-computer" to a happy robot digging away.
Click to expand...
Click to collapse
if you are out of luck, you may have to build a jig or buy one online.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139
Ive used odin before changing roms and have gotten to download mode with combos on my last cappy before that night (dramatic music) en ways..
did some more digging on this bad ass info and learning community "XDA" hehe as to how it got the way it did, I found out I was updated with the new patch when I sent it for screen change to this shop, so...using odin one click with this creates a hang time to where it looked like it was finished after pushing jh6 (which was totally off should have used odin 3 and pushed jh2 then clockwork update to jh7) so thats when I disconnected (second noob mistake of the situation) basically blowing the finalization out and key combs for recovery and download mode. and im guessing the jig was made wrong too at this point >,<.
Oh
wmason92 said:
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Click to expand...
Click to collapse
If you cant get your jig to work take it in to warranty (if your water inicators are sound and no physical damage) and say its power cycling on off at random times (which is true.. ) and it did it when you were sync to mini kies, did it an hour after the OP heh good luck
and I have yet to see the infamous yellow pc sign >,> <,< it can stay on the yellow brick road... thanks for the responses btw
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
Purchase jig from ebay, or google and try igo jig.
If your phone is turning on with jig you are not touching the right prongs. I know, I know it is not easy, but unless it if touching just right, it can turn your phone on.
Holy ******** i got it to download mode! For some reason i kept touching the same pins and nothing would happen. After about readjusting for about 5mn it finally worked!!!!
It has to be just so. Happy to hear
Wait, now its in download mode but my computer keeps saying usb device not recognized.
wmason92 said:
Wait, now its in download mode but my computer keeps saying usb device not recognized.
Click to expand...
Click to collapse
That happens try a different usb port or just borrow someone else computer, I used my networking classes computer my laptop was doing the same thing when I was change roms.
Changed the title to fit the issue, this is not a soft brick this is a boot brick that can affect the charge indicator in power off state as well. So whats the difference the soft brick is when you flash a rom incorrectly and you get the att world screen constantly staying on, the key combinations still work when the phone is like this.. in the case with a boot brick the att screen cycles over and over and the jig may or may not work I haven't been able to fully test it here in this state I have seen a packager attempt to finish once on the recent one but all the key combos I could find didn't function my noob guess is the phone forgot how to ride a bike (meaning is hasn't connected keys to recovery that was being flashed or hardware to there states without being booted normally) ultimate fix is if its in warranty (meaning no physical damage or water) take it back for power on off. the soft brick i've seen before and have fixed with odin 2-3 three times, and ive seen a blown kernel type too where keys and odin fix up like new.
wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
glaze76 said:
I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Very odd - I've never heard of that with a jig.
glaze76 said:
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Have a link to which one you have? It sounds like the solder points on the jig were a little weak. This can happen if they aren't good welds. If you want give one of mine a shot. I'll refund you if it reboots your phone...
Buy one HERE...
I had a boot brick happen to me just the other day. I was running Andromeda 1.1 with stock kernel & modem, and tried to tinker with swapping the AT&T boot screen using connexion2005's video on the subject (NOT insinuating any blame at all, his videos are fantastic).
I tested it successfully the first time, then flashed back the i9000_param_lfs, and pushed a new image to the device again (everything was exactly the same, with the exception of the boot_screen.bat script not making the phone ask for superuser approval while pushing the new logo_ATNT), and everything looked ok.
Reboot device, and...boink.
Black screen, no image at all on power on, only charging screen when usb cable connected. ADB, nothing. 3 button, nothing. Vol up+down, remove battery, insert usb cable, do hokey pokey, nothing. 5 attempts at the 100k resistor jig, for hours, nothing. No download, no recovery. Seems like the phone was toast.
Strange how I had just done this successfully earlier in the day, to now having it completely hard brick this phone.
I ended up taking the phone back to a local warranty center, and they swapped it (1008) for a 1010 (gps works fantastic on this one, btw)...I just hope there's no bill coming if they find out it was rooted and flashed. *crosses fingers and uses any and all karma*
Any ideas what happened? Did I scramble this things boot loader? I've heard how hard it is to fully brick this phone, and looks like I succeeded. How lucky.
I'd just like to know what went wrong so when I (or anyone else) root and flash next time, the chances of this happening are reduced (or better understood).
Thanks

Galaxy Tab 7 Won't Turn On? Here's a Fix it!

I've tried all of the other fix its to get my Galaxy Tab to work. I've tried charging for 12 hrs via wall charger (no response)... I've tried holding the power button plus home key while tapping on the screen at the same time for over 2 minutes (no response) ... I've even tried putting it into download or recovery mode by holding the power button plus the volume key (up or down) for over 2 or minutes (no response) ...
If you're like me and thought the manufacturer was your only option left, there is one thing left you can try.
All I did was remove the shell and unplugged the battery for 30 mins, plugged it back up and viola!!! I have the battery charging icon. And it now boots perfectly into the OS.
Its worth a shot.... here's a video I watched to learn how to remove the shell.
http://www.youtube.com/watch?v=QeRaQR7RU0I
Step by step at ifixit.com
http://www.ifixit.com/Teardown/Samsung-Galaxy-Tab-Teardown/4103/1
Note: you will need a tri-wing screw driver to remove the first two screws. I didn't have one and just used a precision flat head screw driver and it worked like a charm if using enough down force so you won't strip the screw.
Hope this helps someone...
Battery removal resets almost everything -- I'm grateful for your confirmation that it works on the Tab, and also for your links to the hammerless teardown.
noguru said:
Battery removal resets almost everything -- I'm grateful for your confirmation that it works on the Tab, and also for your links to the hammerless teardown.
Click to expand...
Click to collapse
XDA forums has helped me so much, so I'm glad to return the favor to those that need it!
good find
not had the problem myself, but that info is now in my brain for whenever I do have a problem
Good. Thx man!!!
Many thanks man, this saved my (tablets) life. Switched off my tablet last night after charging, for the first time in weeks, just to refresh everything. Tried switching back on this morning and nothing. I've spent all day trying to find out what the hell was wrong and tried all the various button solutions others have mentioned. Nothing worked. came across your info and links and thought I'd give it a try as I had nothing left to lose, tablet was dead. Voila!...back up and running again. I won't be switching it off again in a hurry. Once again great info and much appreciated.
Nice info, really helpfull, my friend gtab p1000 have some problem, wont turn on, and i found this thread, i just try once, and amazing its working, i hit thanks to you
My have turn off and dont turn on, i wiated 2 days and plugged in wall charger, and they work again.
dead tab
still got no luck...i'm tried of your skill yesterterday n my tab still won't turn on...
thanks for the advice
hai, i saw your posting and thank god it really helpful. i own a p1010 and some how it cant turn on twice!. what ever i do, and what ever tricks available in the internet i had tried it all, all with no success. so the first time around i had to sent it for repair and because my tab's warrant had already ended i had to fork out a lot just to make it running. the repair shop just stated that the battery and the touch screen need to be replace. how stupid of me to fall for that. after that my tab is usable again. then it happend again. two days later the same problem occurred. now i know it is not the hardware but the software that causeing all this headache.
now, with your posting, i opened my tab, disconnected the battery for 15 minutes and walla my tab is ok again. phew...save me a lot of money.
i see that the problem might be in the software. i see that alot of p1010 owners face the same problem here after upgrading from froyo to GB. and i notice that the blank screen syndrome would happen if we put it in a standby mode (my standby mode would be you touch the power button once just to make the screen goes blank).
just my 2cents.
amirrash said:
hai, i saw your posting and thank god it really helpful. i own a p1010 and some how it cant turn on twice!. what ever i do, and what ever tricks available in the internet i had tried it all, all with no success. so the first time around i had to sent it for repair and because my tab's warrant had already ended i had to fork out a lot just to make it running. the repair shop just stated that the battery and the touch screen need to be replace. how stupid of me to fall for that. after that my tab is usable again. then it happend again. two days later the same problem occurred. now i know it is not the hardware but the software that causeing all this headache.
now, with your posting, i opened my tab, disconnected the battery for 15 minutes and walla my tab is ok again. phew...save me a lot of money.
i see that the problem might be in the software. i see that alot of p1010 owners face the same problem here after upgrading from froyo to GB. and i notice that the blank screen syndrome would happen if we put it in a standby mode (my standby mode would be you touch the power button once just to make the screen goes blank).
just my 2cents.
Click to expand...
Click to collapse
Hi, I got same problem with you guys with my P6800. Tried all those methods (execpt those removing the casing/battery). I followed one tip and it works. Press and hold the power button for 20 second and release it. The screen displayed an image (icon?) of battery and clock. Some said it also work by pressing the button for 10 second.
thanks for the advice guys
holding the power button works
but my question is why is this happening?it wasnt happening before?
mayurh said:
thanks for the advice guys
holding the power button works
but my question is why is this happening?it wasnt happening before?
Click to expand...
Click to collapse
guys
does no one know whats causing this? is it a firmware issue? or battery?
for me, this happens every time I use the Netflix app. if I don't go into task manager and clear memory after every use of Netflix, my galaxy tab will not turn back on. sometimes fully charging it will wake up the screen, but that's not helping today so I guess I need to remove the shell even though I don't want to. I miss pocket PC's with soft reset buttons!!!
dargpat said:
I've tried all of the other fix its to get my Galaxy Tab to work. I've tried charging for 12 hrs via wall charger (no response)... I've tried holding the power button plus home key while tapping on the screen at the same time for over 2 minutes (no response) ... I've even tried putting it into download or recovery mode by holding the power button plus the volume key (up or down) for over 2 or minutes (no response) ...
If you're like me and thought the manufacturer was your only option left, there is one thing left you can try.
All I did was remove the shell and unplugged the battery for 30 mins, plugged it back up and viola!!! I have the battery charging icon. And it now boots perfectly into the OS.
Its worth a shot.... here's a video I watched to learn how to remove the shell.
http://www.youtube.com/watch?v=QeRaQR7RU0I
Step by step at ifixit.com
http://www.ifixit.com/Teardown/Samsung-Galaxy-Tab-Teardown/4103/1
Note: you will need a tri-wing screw driver to remove the first two screws. I didn't have one and just used a precision flat head screw driver and it worked like a charm if using enough down force so you won't strip the screw.
Hope this helps someone...
Click to expand...
Click to collapse
Hello guys, thanks for your support and excuse me for my english but i'm the same problem with my GT-P1000(i've seen it on the back of my tab !). I've let it charging several hours and try to connect it to Odin which doesn't recognize it ! I got always a black screen and the rear flash led flashing flashing and flashing when it's connected to charger or my PC or when i keep pushing the power button ! Before the brick state i've follow the bad tutorial to root my tab and i've flashed a firmware for galaxy tab 10.1 inch ! Can i try this method?
sephiroth225 said:
Hello guys, thanks for your support and excuse me for my english but i'm the same problem with my GT-P1000(i've seen it on the back of my tab !). I've let it charging several hours and try to connect it to Odin which doesn't recognize it ! I got always a black screen and the rear flash led flashing flashing and flashing when it's connected to charger or my PC or when i keep pushing the power button ! Before the brick state i've follow the bad tutorial to root my tab and i've flashed a firmware for galaxy tab 10.1 inch ! Can i try this method?
Click to expand...
Click to collapse
u flashed tab 10.1 rom into P1000? oh man..
i think it bricked already.. there's nothing left that u can do, flashing back via odin, removing battery or else.. unbrickble mod method is the only way..
Sent from my GT-P1000
same problem
Manuele83 said:
Good. Thx man!!!
Click to expand...
Click to collapse
i have a similar problem my grandson mess up the digitalaizer and i ordered a new one and installed my self. because the tablet been w/o charge for almost a week until i get the new parts and fixed now won't get on, i plug in to charge for 24 hours is showing the 100% battery but still won't start. i look around do different things w/o luck i press the power and the -volune key and nothing, after left ed charging again i unplug the battery for few hours and nothing. i really need help on this. tk's

[Q] Broken power button on my SGS... Solutions?

Hey everybody, I have been using a refurb I9000 for over a year now. After a year of being knocked about, it's still a great phone. I'm running Slim Bean on it at the moment and its handling it great
Unfortunately, a couple months back, the power button stopped working. The phone was acting weird one weekend and stuck in a bootloop - think some water got in it on a night out. Took it apart and stuck it in a bowl for a week, which fixed it and it's been working fine ever since except for the power button.
The button works if you press it repeatedly for like quarter of an hour, but I'm scared I'm wearing it down even more by doing that. Without that button, I can't switch my phone on or do the 3-finger salute.
Right now, if I want to reboot or go into recovery mode, I have to use the buttons in the notification bar. If it runs out of battery, when I plug it in I can still get into download mode by holding the menu button + volume down. To get it into normal mode I have to plug it into a computer with Heimdall installed and get it to print diagnostics 'print-pit), which makes the phone reboot out of download mode into a normal boot. It's not an ideal solution!
When my phone dies when I'm on the road, I'm phoneless for several days.
I'm pretty confident I've voided my warranty on this phone loong ago, plus trying to get a replacement is the easy way out
I've seen custom 'battery charge mode' firmware out there- you know the screen you get when the phone is switched off and you plug it into a charger? Somebody had written a custom one of those screens with extra useful information on it. I can't remember what it was called though! Google hasn't been useful at all in finding it, either. I've also noticed the charging screen looks different on my Slim Bean ROM compared to the stock one. So it must be something that's fairly easy to customize...
With that in mind, I might try hacking the charge screen to listen to the menu + volume control buttons and be able to boot the phone that way.
Either that or I make a USB jig that can send enough bits to the phone in download mode to get it to reboot...
But as I'm only good at breaking hardware, I think I'll stick to software hacking for now.
Does anyone know the name of that custom battery charging screen I mentioned? Maybe there's more than one? If I can get ahold of them I can hopefully find out how they work.
This is a pretty specific + techy question, so apologies mods if this is in the wrong section! I don't think I'm allowed to make threads in the Android dev. forums yet though- you need to have over a certain number of posts for that, right?
- Written painstakingly on my phone and oh God I wish I'd used Tapatalk. Why is the stock browser still so crap at user input?

[Q] Did I ruin it? Sigh...

Hello everyone,
Ok so here is the story,
I had this Galaxy Gear sitting around for awhile and thought to myself I think I should try and root this thing...
I have rooted phones before so I was pretty confident this was going to be easy. Well I was wrong. I went through countless posts and youtube videos finally figuring out small things I did wrong....( I have a new laptop so I had a bunch of android stuff i needed to download)
I eventually managed to root it and install Superuser. Everything was going great until I had to install recovery. I powered it down into the download option and I managed to flash what I thought was the recovery...Problem was I forgot to turn off the restart feature in Odin. SO the watch restarted. When trying to get back into download mode I realized the power button would not do anything anymore. Just stopped working. Well I figured ok maybe I can get around this ...so I downloaded an app to restart the watch for me, you know bypassing the actual button...well....that was a pretty stupid idea. I now have a watch that will not power on. If I plug it into its cradle into the computer it charges but with no button I guess there is no way to actually turn it back on...
I am at a loss now and thought maybe I could fish for some fixes.
Any ideas?
PS: the button goes in...it doesn't seem like the physical button is actually broken.
So just an update:
I managed to get it back up by waiting a half hour and pressing the power button a few times in a row (Honestly I dont know why it worked now) but the button is still sort of useless because it still will not work to power down or reset. Which means there is still no way to get it into download mode.
I am not sure if this is a physical button problem or did I actually do something when it was flashing recovery.
Have you got null on it?

Categories

Resources