Database Develop

[Q] I Actually Managed to Brick this Phone

Hey guys I think I actually did it. I was going to install the JPC Froyo Rom, and somehow booted into recovery in the ROM. Now whenever I turn the phone on it boots into recovery, and none of the button combinations work for putting it into Download mode so I can flash back to stock. On the i9000 thread it says that if you get into this situation you cannot flash back. Any of you guys run into this issue? If not then it looks like I'll be trying to convince an ATT rep to give me a new phone

Try powering off... Then hold vol up and down buttons then plug in usb.... That happened to me... Your not bricked
Sent from my SAMSUNG-SGH-I897 using XDA App

Connect to adb and run reboot command
Sent from my GT-I9000 using XDA App

Nope
Nope sorry guys I know all of what you just said. As for plugging in USB while holding volume buttons, it'll just go to that battery charging screen, and adb doesn't work because it doesn't boot past recovery. Sorry guys but yes it was bricked. It's okay though because I just went to ATT and since they can't identify the problem they just replaced the phone

Thought mine was bricked one night, too. Same scenario. Tried dropping the SIM and SD card out even though I didn't think it would make a difference, but it did. Got to download screen and reflashed with ODIN.
Good luck.
Sent from my SAMSUNG-SGH-I897 using XDA App

KCutrer1 said:
Nope sorry guys I know all of what you just said. As for plugging in USB while holding volume buttons, it'll just go to that battery charging screen, and adb doesn't work because it doesn't boot past recovery. Sorry guys but yes it was bricked. It's okay though because I just went to ATT and since they can't identify the problem they just replaced the phone
Click to expand...
Click to collapse
If you pull the battery, then put the battery in. hold both volume buttons buttons, and then plug the phone into the computer, it didn't boot to download?

Im curious if you even tried to use the Odin one click thread
There are 4 or 5 ways in that thread on how to get to download mode. And how exactly does this relate to development...just another curious thought. Well, you are getting a new phone, just hope that ATT or Samsung don't try to figure out the cause of your phone being "bricked".

AGAIN!
Okay after this I swear I won't be messing around with Froyo anymore. Here's the story: I got into download on the replacement captivate. Tried to install JPC froyo, but it never started flashing so I unplugged it from Odin and then tried to turn it back on. It goes to the normal "connect phone to computer" screen. However no attempts to get back into download mode have worked. Holding both volume buttons and power until second black screen doesn't work, booting while holding volume down doesn't work, holding both volume buttons and then inserting USB cable doesn't work. I think I'm stuck in this screen unless there's some incredible way I have yet to try. Anybody have any ideas? I would greatly appreciate feedback from the experienced users (Zilch25, designgears, kaik, reaver117), because I think I'd be pushing it trying to get it replaced a second time in such rapid succession
To flashman2002:
I put it in this section because it's in the development section that most flashing and such occurs so I thought there would be the greatest knowledge base. And yes I've pored over the one click thread and none of the methods mentioned there have any effect!

Jeez, I just scared the **** out of myself. I ran the remove lagfix script and it rebooted my phone but it was just a black screen. So I take the battery out. Bad Idea. It showed the ATT screen but just black after that. I could get it into recovery mode but not download. Then I messed some more and would only show a vague disconnected pic.
Finally I got it into download by doing this: (had odin open before hand)
1. took everything out including sim and usb cable.
2. quickly inserted battery and held volume buttons and very quickly inserted usb.
I'm pretty sure its the speed that matters because I tried about 4 times and only when I did it really fast did it work.

ThisWasATriumph said:
Jeez, I just scared the **** out of myself. I ran the remove lagfix script and it rebooted my phone but it was just a black screen. So I take the battery out. Bad Idea. It showed the ATT screen but just black after that. I could get it into recovery mode but not download. Then I messed some more and would only show a vague disconnected pic.
Finally I got it into download by doing this: (had odin open before hand)
1. took everything out including sim and usb cable.
2. quickly inserted battery and held volume buttons and very quickly inserted usb.
I'm pretty sure its the speed that matters because I tried about 4 times and only when I did it really fast did it work.
Click to expand...
Click to collapse
Nope. Unless you can do this with godly speed I dont think it'll work. I just got to the "Connect Phone to Computer" screen again.

You had the usb in before anything appeared on the screen right?

ThisWasATriumph said:
You had the usb in before anything appeared on the screen right?
Click to expand...
Click to collapse
Yeah originally. I can get to that screen now by just putting the battery in and holding power button. It seems to behave exactly like it normally would, just can't get out of it.

What screen? The screen you want has a big yellow triangle and says download.

ThisWasATriumph said:
What screen? The screen you want has a big yellow triangle and says download.
Click to expand...
Click to collapse
No it's on the phone...!...computer screen. That's what I'm saying, it's been stuck here for a while and none of the methods described on the one click thread work. I've been here before and just holding volume buttons and holding down power for it to boot twice and releasing would do it. Not so anymore. Can't get into download mode doing anything!

Well I read In the SRE thread I think that there are reports of newer phones not responding to any button combos. Bad batch they said not on purpose...
Also for the i9000 apparently you only have to hold the down volume key so since you flashed a i9000 rom try that if you haven't already.
You cant get into recovery right? Just holding volume and power then letting go of power after a bit?

Adb reboot download...
Sent from my SAMSUNG-SGH-I897 using XDA App

ThisWasATriumph said:
Well I read In the SRE thread I think that there are reports of newer phones not responding to any button combos. Bad batch they said not on purpose...
Also for the i9000 apparently you only have to hold the down volume key so since you flashed a i9000 rom try that if you haven't already.
You cant get into recovery right? Just holding volume and power then letting go of power after a bit?
Click to expand...
Click to collapse
Nope none of it works. I just got it replaced less then 3 hours ago and I already bricked it. I hope somebody finds out something that'll get this fixed. Maybe some way to force download mode through a computer application or something.

Well theres adb like mentioned above but im pretty sure that requires at least recovery mode working.
Like i said before i was stuck on the same screen so maybe theres still hope.
If all else fails someone will figure out how to JTAG these things eventually...

ThisWasATriumph said:
Jeez, I just scared the **** out of myself. I ran the remove lagfix script and it rebooted my phone but it was just a black screen. So I take the battery out. Bad Idea. It showed the ATT screen but just black after that. I could get it into recovery mode but not download. Then I messed some more and would only show a vague disconnected pic.
Finally I got it into download by doing this: (had odin open before hand)
1. took everything out including sim and usb cable.
2. quickly inserted battery and held volume buttons and very quickly inserted usb.
I'm pretty sure its the speed that matters because I tried about 4 times and only when I did it really fast did it work.
Click to expand...
Click to collapse
I know it doesn't help you out now, but when you remove the lag fix, just leave it set on the black screen. It's doing its thing. It will reboot when it's done. The home keys should still light up if you press them in this state...

Well thanks for your input anyway guys. Hopefully somebody figures something out. For now I guess I'll keep the SIM in my old iPhone 3G so I at least have a phone. Tomorrow I'll go to another ATT store in my area. Chances are the rep won't know what the hell that screen means and will replace the phone promptly.

[Q] MIGHT have hard bricked phone :(

So I was attempting to flash back to stock with Odin (I was using Assonance 5.2). I turned the phone off, then while holding the volume buttons plugged in the USB like normal. Then Odin said added the phone, then I hit start. And it seemed like it was working just fine, then all of a sudden the screen on the phone turned red. Then the status bar on Odin stopped moving completely (stayed for awhile). So I think I made the next big mistake of just disconnecting the USB and taking out the battery. So now the phone won't turn on. So I'm not sure I hard bricked the phone or what? Anyone have any idea? Thanks!
I've plugged the phone into the outlet charger, still nothing happens. This happened like maybe 15 min ago. No action when plugged in the computer or charger. Can't even boot into recovery I don't think. the power button was giving me some trouble earlier today. whenever I was trying to wake the phone up, it seemed to take a few clicks of the power button to wake the phone. This happened only after I flashed Assonance 2.5, so I wanted to flash to an earlier version of the rom. thanks!

What you want to do is get into Download Mode, and flash with Odin One-Click JF6 to get your phone working again..
Have you tried all the various button combos to get into Download Mode? .
If the button combos don't work, you can always try to build/buy a JIG which will force your phone into Download if it's still possible on your phone.

I've tried to get into download mode, but can't seem to do it. I've tried holding the volume up and down button then plugging in the usb (which didn't work). then i tried the taking the battery out, then holding the volume up and down button and power button, then plugging in the usb, then reinserting the battery, then taking my hand off the power button (which didn't work). what is the JIG method?
edit. ok i have no clue wtf just happened, but i am currently in download mode using odin and flashing back to stock.....this is just too weird.....sooo any rom suggestions?

Look in my signature for an example of a JIG.

norcal einstein said:
Look in my signature for an example of a JIG.
Click to expand...
Click to collapse
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending

i clicked on the link but it won't let me go the page. below is the message it gave me.
marefin, you do not have permission to access this page. This could be due to one of several reasons:
Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.

marefin said:
cool i'm actually gonna go ahead and get one this things......JUST in case of future screw ups that don't have a happy ending
Click to expand...
Click to collapse
Definitely a great idea having the jig. Nor cal can attest to the late night save that jig provided me.
Sent from my SGH-T959D using XDA App

[Q] Boot Brick

Okay I was using odin one click it was at rebooting device after it completed pushing stock onto the phone thats when I discounted the usb.... should have waited two secs I know but now the phone doesn't seem to get past the att world phone screen keeps looping over and over I have tried all the key combos different times and ways, vol up and down being held doesn't get to download mode the screen remains black plunging in seems to get to charge mode where even plunging into the wall charger it loops trying to calculate the battery status... any method I haven't tried... I did get it to boot once full and was usable didn't think to redo odin at the time and restarted back to this mess...tried three different jigs using the 100k 5% X3 even through its not a full brick due to the button combos gotten no where. Please Help

Search the forum to build a jig in order to get into download mode. Or you may need to buy one just in case in the future.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139

Try this:
Open Odin and plug your cable into your computer but not your phone yet
Pull battery on phone and put it back in
Hold both volume buttons down and then plug your phone in
It should go into download made and you can reflash the stock ROM

Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.

Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.

norcal einstein said:
Try this:
1. Remove battery from phone, SIM card and MicroSD card (if you have one)
2. Wait AT LEAST 10 seconds with your phone in this state
3. Hold Volume Up/Down, don't let go
4. While holding the volume keys, insert the battery
If this worked, you should be in Download Mode almost instantly.
There are a lot of key combos for Download Mode, this is just one of them. If all the button combos don't work, you need to build/buy a JIG to force your phone into Download Mode.
Click to expand...
Click to collapse
Ahah Thats the same exact steps I was able to get the phone to boot that one time instead of the up down I was still attempting it to get past the loop holding the power button instead using those steps, if I had know it would have been one of the only times I would see it in there I would have pushed it to download with adb though...
can't test getting it to download mode now took it back fit the description of the standing on/off issue with the device still honored by warranty. And I wouldn't have posted without searching everywhere to make a jig, I made three of them though I noticed it still didn't get to download mode. I made sure that the last two jigs were done correct. Think that when it was disconnected from odin it wasn't done finalizing after the stock push gah >,< live and learn and do something else to the cappies XD.
Thanks for the link placing an order just in-case ~whistles looking around then side to side pushes another rom~ lalala

To offer my own advice if it ever happens again, what I've been able to do is:
1. Pull the battery out
2. Put it back in
3. Open Odin
4. Hold Both Volume Buttons (without holding the power button)
5. Plug the phone back in
It went immediately into download mode for me, Odin managed to time out several times while I was trying to flash a co-worker's Captivate to the official Froyo leak. One of those times I couldn't even get the phone to come up with any screen. I really do think this thing cannot be bricked.

BeowulfShaeffer said:
That has been my experience so far, too. I've "bricked" twice, once with an "all black" screen, and once with the phone-!-computer screen. I've yet to need a jig, though I thought I may have needed it last night when I got the "all black" screen.
Keep trying the different button press methods to get into download mode. It took me 4 attempts to get from "all black" to "phone-!-computer" to a happy robot digging away.
Click to expand...
Click to collapse
if you are out of luck, you may have to build a jig or buy one online.
http://cgi.ebay.com/ws/eBayISAPI.dl...69977&ssPageName=STRK:MESELX:IT#ht_623wt_1139

Ive used odin before changing roms and have gotten to download mode with combos on my last cappy before that night (dramatic music) en ways..
did some more digging on this bad ass info and learning community "XDA" hehe as to how it got the way it did, I found out I was updated with the new patch when I sent it for screen change to this shop, so...using odin one click with this creates a hang time to where it looked like it was finished after pushing jh6 (which was totally off should have used odin 3 and pushed jh2 then clockwork update to jh7) so thats when I disconnected (second noob mistake of the situation) basically blowing the finalization out and key combs for recovery and download mode. and im guessing the jig was made wrong too at this point >,<.
Oh
wmason92 said:
Can anyone please help, i have the exact same problem. No matter how i try to enter download mode, it just gives me a charging sign and when i start my phone, it goes into an infinite boot loop.
Click to expand...
Click to collapse
If you cant get your jig to work take it in to warranty (if your water inicators are sound and no physical damage) and say its power cycling on off at random times (which is true.. ) and it did it when you were sync to mini kies, did it an hour after the OP heh good luck
and I have yet to see the infamous yellow pc sign >,> <,< it can stay on the yellow brick road... thanks for the responses btw

Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.

wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
Purchase jig from ebay, or google and try igo jig.
If your phone is turning on with jig you are not touching the right prongs. I know, I know it is not easy, but unless it if touching just right, it can turn your phone on.

Holy ******** i got it to download mode! For some reason i kept touching the same pins and nothing would happen. After about readjusting for about 5mn it finally worked!!!!

It has to be just so. Happy to hear

Wait, now its in download mode but my computer keeps saying usb device not recognized.

wmason92 said:
Wait, now its in download mode but my computer keeps saying usb device not recognized.
Click to expand...
Click to collapse
That happens try a different usb port or just borrow someone else computer, I used my networking classes computer my laptop was doing the same thing when I was change roms.

Changed the title to fit the issue, this is not a soft brick this is a boot brick that can affect the charge indicator in power off state as well. So whats the difference the soft brick is when you flash a rom incorrectly and you get the att world screen constantly staying on, the key combinations still work when the phone is like this.. in the case with a boot brick the att screen cycles over and over and the jig may or may not work I haven't been able to fully test it here in this state I have seen a packager attempt to finish once on the recent one but all the key combos I could find didn't function my noob guess is the phone forgot how to ride a bike (meaning is hasn't connected keys to recovery that was being flashed or hardware to there states without being booted normally) ultimate fix is if its in warranty (meaning no physical damage or water) take it back for power on off. the soft brick i've seen before and have fixed with odin 2-3 three times, and ive seen a blown kernel type too where keys and odin fix up like new.

wmason92 said:
Well the same thing happened to me and i got stuck with in an unlimited boot animation. Ive trying everything key combo possible and ive tried a jig but it just makes it reboot, and yes im sure im touching the right pins. If anybody can help with this dilemma i would really appreciate it. I want to return with warranty but my phone has a custom boot animation so im sure att probably wont accept it if they notice it.
Click to expand...
Click to collapse
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.

glaze76 said:
I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Very odd - I've never heard of that with a jig.

glaze76 said:
I have the same thing happening to me. Att boot screen, then it loops on the ROM logo, over and over. I get 1 vibrate then 2 following also. I purchased a Jig on ebay but it just keeps rebooting the phone, doesn't get it into download mode.
Click to expand...
Click to collapse
Have a link to which one you have? It sounds like the solder points on the jig were a little weak. This can happen if they aren't good welds. If you want give one of mine a shot. I'll refund you if it reboots your phone...
Buy one HERE...

I had a boot brick happen to me just the other day. I was running Andromeda 1.1 with stock kernel & modem, and tried to tinker with swapping the AT&T boot screen using connexion2005's video on the subject (NOT insinuating any blame at all, his videos are fantastic).
I tested it successfully the first time, then flashed back the i9000_param_lfs, and pushed a new image to the device again (everything was exactly the same, with the exception of the boot_screen.bat script not making the phone ask for superuser approval while pushing the new logo_ATNT), and everything looked ok.
Reboot device, and...boink.
Black screen, no image at all on power on, only charging screen when usb cable connected. ADB, nothing. 3 button, nothing. Vol up+down, remove battery, insert usb cable, do hokey pokey, nothing. 5 attempts at the 100k resistor jig, for hours, nothing. No download, no recovery. Seems like the phone was toast.
Strange how I had just done this successfully earlier in the day, to now having it completely hard brick this phone.
I ended up taking the phone back to a local warranty center, and they swapped it (1008) for a 1010 (gps works fantastic on this one, btw)...I just hope there's no bill coming if they find out it was rooted and flashed. *crosses fingers and uses any and all karma*
Any ideas what happened? Did I scramble this things boot loader? I've heard how hard it is to fully brick this phone, and looks like I succeeded. How lucky.
I'd just like to know what went wrong so when I (or anyone else) root and flash next time, the chances of this happening are reduced (or better understood).
Thanks

[Q] unbrick galaxy mini?

so i rooted my phone installed rom manager and flashed something like colckwork rom of hawai mini i switched of my mobile.Today in morning when i tried to tun it on it wont only a black screen no sound no logo no vibration I even tried to remove and insert battery but no luck.I think its a hard brick i got this mobile on 28 feb 2011 and it is still under 1 year warrenty of samsung so can i get a new mobile in place of it or just recover it.(I have the UK system here noot of USA)
can you tell me any way to unbrick it any any one

I have done something similar to my Samsung Vibrant. Rooted and was in process of installing new ROM when on restart got a screen that has Vibrant at the top of screen and Samsung on the bottom of screen then a blank black screen and then goen into a vibrating loop of single vibrate and then another single vibrate and then a triple vibrate and then it starts the loop over again. The only thing I can do is pull the battery to stop it. Anyone know of any thing I can do to correct this or to revert the ROM or anything?
Thank you
Larry

Take it to T-Mobile and say when you turned it on it was like this and they might send it off to be replaced.

i hate those people who wanna pay their insurance for their silly things and fails!
i hope, tmobile won't take it back.
let's see..it's really hard to brick a phone though.
had some problems with my further hd2 as well..yeah, you get really annoyed but if you chill out, in 99% of the cases you'll find a solution.
DN41

so guys i live in india here it is called galaxy pop i went to samsung service center and there they replaced my motherboard for free cause it was still in warranty .I will get it next tuesday

I have this model, too. But it is called GT-S5570. It works fine, but i bought it network lock. Have you succeded unlock it?

Had the same, the solution is simple:
Download the newest firmware at samfirmware.com
Use Odin Multi Downloader to upload the firmware to your mobile
(mobile needs to be in download mode, this should still work. Try volume down + home + power)
Just upload the clean firmware and it should be done. The complete guide is placed on the same website on the download page.

OfficialDenzil said:
Had the same, the solution is simple:
Download the newest firmware at samfirmware.com
Use Odin Multi Downloader to upload the firmware to your mobile
(mobile needs to be in download mode, this should still work. Try volume down + home + power)
Just upload the clean firmware and it should be done. The complete guide is placed on the same website on the download page.
Click to expand...
Click to collapse
download mode is not available while is bricked, changing the firmware is NOT an option.

hi
yeah same thing happen to me
even the samsung survice centre is lame they tell me that it will cost me
so i bring ma set back and do that jig method and it works more than charm i install ma new cyanogen mod and it is working greatly .if u want to find jig method type unbricking galaxy s jig.
it also works for my mini

Just a little german ?!
DN41 said:
i hate those people who wanna pay their insurance for their silly things and fails!
i hope, tmobile won't take it back.
let's see..it's really hard to brick a phone though.
had some problems with my further hd2 as well..yeah, you get really annoyed but if you chill out, in 99% of the cases you'll find a solution.
DN41
Click to expand...
Click to collapse
(I don't have this problem, but...)
And I, I hate little brained guys who says f***king silly things like you. You're not just a little german, you're also a big sucker.
I swear you will have a problem with your phone, and no solution. Really I wish you that.
For other people who has this problem, don't worry, your phone is frozen, so they can't diagnose it. Just say you was syncronizing with Kies, and it happend the phone turned off and that's impossible to restart it. They'll just give you a new one or repair it.

HI
try these ways
it works with my galaxy s
Hold down Vol UP+Vol Down+Power, the screen will flash black, continue holding down all 3 buttons, you will see the "phone--!--PC" screen again, continue holding all 3 buttons, the screen will flash black again, release the power button only. This will put you into Download Mode.
If this does not work, open odin. Then connect your usb cable to your phone and computer. While the USB is plugged in and Odin running press and hold volume down + Home + Power. Once the black screen comes (flashes) release the Power Button. It should get into download mode.
Additionally it is possible to get into the Download Mode using a kind of micro-usb connector,
the last thing u can try is the jigs

ilazially said:
HI
try these ways
it works with my galaxy s
Hold down Vol UP+Vol Down+Power, the screen will flash black, continue holding down all 3 buttons, you will see the "phone--!--PC" screen again, continue holding all 3 buttons, the screen will flash black again, release the power button only. This will put you into Download Mode.
If this does not work, open odin. Then connect your usb cable to your phone and computer. While the USB is plugged in and Odin running press and hold volume down + Home + Power. Once the black screen comes (flashes) release the Power Button. It should get into download mode.
Additionally it is possible to get into the Download Mode using a kind of micro-usb connector,
the last thing u can try is the jigs
Click to expand...
Click to collapse
Man that volume up and down doesn't support if you have a completely hard bricked phone .
And the jig does works but why use your penny if xda developed a unbricker wich really works for free
I prefer xda undricker the best
Sent from my GT-S5570 using xda premium

Hello guys.I have a galaxy mini and i tried to root it.Everything went fine.Then i saw that an application "Rom manager" would be helpful for my phone.
So i installed it(like an idiot).
Then i tried to install clockwork mode (smthg like that from rom manager) and boom!Everything went black.
I tried to go into recovery mode,download mode NOTHING.
I tried to a lot of things but nothing is working.
Odin recognises my phone when i use volume up+home+end!But it stucks on setup.Again tried to do it in that way but still nothing.
Last i tried that jig thing.I bought 3x100k ohm resistors and do it like he says(that video from youtube) BUT STILL NOTHING.
I dont know what to do!
I would be gratefull if some1 could give me an advice to make it to turn on!
Tyyy.

This is exactly what happened to me too. Did Service centre repair it for free ? What did you tell them ? Please help. ITs urgent/ Bricked black screen.
sahilg009 said:
so i rooted my phone installed rom manager and flashed something like colckwork rom of hawai mini i switched of my mobile.Today in morning when i tried to tun it on it wont only a black screen no sound no logo no vibration I even tried to remove and insert battery but no luck.I think its a hard brick i got this mobile on 28 feb 2011 and it is still under 1 year warrenty of samsung so can i get a new mobile in place of it or just recover it.(I have the UK system here noot of USA)
can you tell me any way to unbrick it any any one
Click to expand...
Click to collapse

Swanks
Guys trust me ROM manager sux bigtym i tried all the cures bt didnt work. Handed it ova to samsung guys n they replaced my motherboard!

sopree said:
Hello guys.I have a galaxy mini and i tried to root it.Everything went fine.Then i saw that an application "Rom manager" would be helpful for my phone.
So i installed it(like an idiot).
Then i tried to install clockwork mode (smthg like that from rom manager) and boom!Everything went black.
I tried to go into recovery mode,download mode NOTHING.
I tried to a lot of things but nothing is working.
Odin recognises my phone when i use volume up+home+end!But it stucks on setup.Again tried to do it in that way but still nothing.
Last i tried that jig thing.I bought 3x100k ohm resistors and do it like he says(that video from youtube) BUT STILL NOTHING.
I dont know what to do!
I would be gratefull if some1 could give me an advice to make it to turn on!
Tyyy.
Click to expand...
Click to collapse
This!!!
rooted phone!! installed Titanium Backup pro, rom-manager (though i didnt use it).
First i removed yahoofinance.apk thingy... it went black but recovered to charging mode (battery charging screen)... odd i thought.. and (like a idiot) booted up and removed livebackground forest thingy... now!
Pitch black, no state of recovery.
Just thist:
Vol up, home and power button. makes it visible to windows and odin.. KIES failes to connect it...
Its almost like... i got one first warning.. and then samsung decided to **** me!
is it somekind of "security lock"?, its not like i removed the kernel.
EDIT: so.. im messing around... The only thing that one really gets comunication with is the modem circuits, so it looks that way... But then what do i know...
ODIN connects to the same com-port as the samsung modem reports having in device manager!, so i asume this is unit it uses to when transfering the data, flashing.
Other: i get some different behaviors... etc, i would use "volup, home and power" to make it visible in win and then i could just use the power button to get the connection on and off (or rather reset! since i just one time got it to actually stay disconnected).
Now on the other hand i cant use the just the "Vol up" button combo, i have to press both Vol up and down with pwr and home to get it to connect with drivers and show up in ODIN etc..
In some cases u have to have battery unpluged and show it in while holding button combo and sometimes u dont..
I cant make out anything out of this, but maby some of u guys can!?

Rom Manager screwed your phone. Not uninstalling forest wallpaper.
I got my phone hard bricked because of ROM manager. I have given it to the service center. Waiting for them to fix it.

chemicalrage said:
Rom Manager screwed your phone. Not uninstalling forest wallpaper.
I got my phone hard bricked because of ROM manager. I have given it to the service center. Waiting for them to fix it.
Click to expand...
Click to collapse
Is there any other option before we go to the service center??
I mean to fix it alone...

sopree said:
Is there any other option before we go to the service center??
I mean to fix it alone...
Click to expand...
Click to collapse
If the phone is hard bricked (no download mode, no battery charge indicator when power plugged in), you really do not have a choice.
While people claim to be able to use jtag / USB jig (see the only thread started by me in the accesories section of this miniforum), I do not have clear answers in that thread.

genieass said:
If the phone is hard bricked (no download mode, no battery charge indicator when power plugged in), you really do not have a choice.
While people claim to be able to use jtag / USB jig (see the only thread started by me in the accesories section of this miniforum), I do not have clear answers in that thread.
Click to expand...
Click to collapse
That jig thing doesnt work..pfff

[Q] Seriously need some help before I go crazy

Ok so here goes my soft brick story.
First off I've been searching for about 4 days and cant get anything to work.
The captivate has a bad power button, I've tried opening it up, doing that QCD cleaner and nothing works. So anyways I got USB debug on and was able to get into DL mode with ADB and used Odin one click, but thats where the problem started. After about 2 hrs of waiting after the process started it just hung so I pulled the cable, and now Im in a soft brick(Phone---!----PC). I read of some people saying they can flash while in that screen but I cant get Odin or Heimdall to even recognize the phone while it is like this.
I've tried the most recommended way of pulling battery, connecting phone to USB and holding both volume buttons to get it into download mode but that doesnt work. As soon as I pop the battery into the phone the Phone---!---PC screen pops up, I tried with both volume buttons, just the bottom volume and just the top volume button but nothing works, as soon as the battery goes into the phone the Phone---!---PC screen pops up.
Only thing left to try is making a USB Jig but I was wondering if anyone has had this problem before and was able to fix it without the jig. Im doing this for a friend and I dont want to have to wait for the JIG to ship to my house, and Im not confident enough in making my own considering I dont even have a spare mini USB cable(I have an HTC Amaze so the cable isnt the same) and the cable I'm using is someone elses so I cant tear it up to even try and make a jig.
Also I've tried three different USB ports on my laptop and another three on a different laptop but it still doesnt get recognized.
Sorry for the long ass rant. but this is just driving me insane, I'm about to just use this phone as batting practice if I cant get this to work.
Edit: oh yea this happened while trying the Odin one click to get it back to stock, no GB or anything of the sort, the phone was still Froyo, just a custom froyo rom.

RXDriv3r said:
Ok so here goes my soft brick story.
First off I've been searching for about 4 days and cant get anything to work.
The captivate has a bad power button, I've tried opening it up, doing that QCD cleaner and nothing works. So anyways I got USB debug on and was able to get into DL mode with ADB and used Odin one click, but thats where the problem started. After about 2 hrs of waiting after the process started it just hung so I pulled the cable, and now Im in a soft brick(Phone---!----PC). I read of some people saying they can flash while in that screen but I cant get Odin or Heimdall to even recognize the phone while it is like this.
I've tried the most recommended way of pulling battery, connecting phone to USB and holding both volume buttons to get it into download mode but that doesnt work. As soon as I pop the battery into the phone the Phone---!---PC screen pops up, I tried with both volume buttons, just the bottom volume and just the top volume button but nothing works, as soon as the battery goes into the phone the Phone---!---PC screen pops up.
Only thing left to try is making a USB Jig but I was wondering if anyone has had this problem before and was able to fix it without the jig. Im doing this for a friend and I dont want to have to wait for the JIG to ship to my house, and Im not confident enough in making my own considering I dont even have a spare mini USB cable(I have an HTC Amaze so the cable isnt the same) and the cable I'm using is someone elses so I cant tear it up to even try and make a jig.
Also I've tried three different USB ports on my laptop and another three on a different laptop but it still doesnt get recognized.
Sorry for the long ass rant. but this is just driving me insane, I'm about to just use this phone as batting practice if I cant get this to work.
Edit: oh yea this happened while trying the Odin one click to get it back to stock, no GB or anything of the sort, the phone was still Froyo, just a custom froyo rom.
Click to expand...
Click to collapse
First, please don't double post, because it clutters up the forum. You could have added a post to your original thread.
Second, with this type of problem, I didn't need a jig. First, take out the battery and put it back in (dont turn on!!). Next, plug the USB part of the data cable in the computer. Use one of the various combos to get into recovery mode, like hold both volume buttons, and power/lock button). It should show the recovery screen. Then plug the microUSB part into your phone and run one click recovery here: http://forum.xda-developers.com/showthread.php?t=731989. This should solve your problem.

Please dont quote the OP when youre the first post...
Sent from my GT-I9300 using xda premium

Are you trying to update from stock?
Sent from my cm_tenderloin using xda premium

You need a Samsung cable... I tried to do the same thing with an LG cable, what a nightmare!
Sent from my cm_tenderloin using xda premium

RXDriv3r,
Use that screen the same as you would the regular Download mode screen.
U may have to try Linux if Windows don't work.
And see this thread by jmtheiss, for more helpful info... Captivate Connection Issues and Download Mode Help
Sent from my SAMSUNG-SGH-I897 using xda premium

RXDriv3r said:
Ok so here goes my soft brick story.
First off I've been searching for about 4 days and cant get anything to work.
The captivate has a bad power button, I've tried opening it up, doing that QCD cleaner and nothing works. So anyways I got USB debug on and was able to get into DL mode with ADB and used Odin one click, but thats where the problem started. After about 2 hrs of waiting after the process started it just hung so I pulled the cable, and now Im in a soft brick(Phone---!----PC). I read of some people saying they can flash while in that screen but I cant get Odin or Heimdall to even recognize the phone while it is like this.
I've tried the most recommended way of pulling battery, connecting phone to USB and holding both volume buttons to get it into download mode but that doesnt work. As soon as I pop the battery into the phone the Phone---!---PC screen pops up, I tried with both volume buttons, just the bottom volume and just the top volume button but nothing works, as soon as the battery goes into the phone the Phone---!---PC screen pops up.
Only thing left to try is making a USB Jig but I was wondering if anyone has had this problem before and was able to fix it without the jig. Im doing this for a friend and I dont want to have to wait for the JIG to ship to my house, and Im not confident enough in making my own considering I dont even have a spare mini USB cable(I have an HTC Amaze so the cable isnt the same) and the cable I'm using is someone elses so I cant tear it up to even try and make a jig.
Also I've tried three different USB ports on my laptop and another three on a different laptop but it still doesnt get recognized.
Sorry for the long ass rant. but this is just driving me insane, I'm about to just use this phone as batting practice if I cant get this to work.
Edit: oh yea this happened while trying the Odin one click to get it back to stock, no GB or anything of the sort, the phone was still Froyo, just a custom froyo rom.
Click to expand...
Click to collapse
are you putting the battery back in first? if so try leaving the battery out...I just tryed it on my spare captivate i took the battery out removed sim and sd card plugged the usb in and held all 3 buttons to simulate the power button sticking and then put the battery back in and it went right to download mode i hope this helps you.

Sorry about the duplicate threads, didnt realize that one had gone through since I got an error when I pressed post.
Anyway @nirajpant7 I cant pop the battery in the phone without it coming on by itself. Even if I dont press any buttons as soon as the battery goes in, the screen comes on with the phone--!--PC screen. Also my power button does not work so I cant really try all the button combos.
@SGA was trying to stay stock, phone was on a custom 2.2 rom so I wanted a stock 2.2 rom for the phone. Also does the cable matter that much? Hmm I dont think I have a way of getting a OEM Samsung cable.
@4-2ndtwin Yea thats what I heard but Odin, nor Kies, nor Heimdall recognize the phone while in that screen. Also on that thread you posted I've tried all the different ways more than once with no luck.
Anyway thanks for the fast replies guys I'll keep working on this and update with any new info...or a nice video of a flying captivate Lol

Just try another cable... even if it not OEM. In most cases where the PC does not match up the drivers its the cable. Even when I assigned the drivers manually to the device it would not work. It would always register as an unknown Google device. A new cable quickly sorted the problem out, and you can see that has been the main issue for anyone where Odin does not recognise. I am currently using a generic cable from the dollar store and it works, but the phones are picky. Sometimes they don't even like their own cables.
My cappy is recognised with cheap cable, my nexus s won't for the life of it identify with anything other than its own cable....
Its worth a shot...
Sent from my cm_tenderloin using xda premium

-SGA- said:
Just try another cable... even if it not OEM. In most cases where the PC does not match up the drivers its the cable. Even when I assigned the drivers manually to the device it would not work. It would always register as an unknown Google device. A new cable quickly sorted the problem out, and you can see that has been the main issue for anyone where Odin does not recognise. I am currently using a generic cable from the dollar store and it works, but the phones are picky. Sometimes they don't even like their own cables.
My cappy is recognised with cheap cable, my nexus s won't for the life of it identify with anything other than its own cable....
Its worth a shot...
Sent from my cm_tenderloin using xda premium
Click to expand...
Click to collapse
Found something that might help you, do you still have the same problem?