Raplacing the digitizer - HD7 General

Ok so i have a cracked digitizer...
I am going to replace it myself, however this phone is obviously not a straight forward repair.
Anyone have any personal experience replacing the digitizer on this phone? I have seen the youtube videos and read the xda.cn chinese breakdown, just looking for some personal input on the process if someone has one.
Also what will i need to rebuilt it? Do i need double sided tape etc. Thanks

80 views and no ones ever had experience with this?

i replaced it on 2 hd7 phones.
its a real pain to get it off because the glue tape they use goes all the way around, and its strong stuff.
you need to take apart the entire phone to get to the ribbon cable where the digitizer plugs in, so just look for some youtube videos of a tear down and watch carefully.
honestly the hardest part for me was getting the screen and digitizer clean of fingerprints and tiny broken glass pieces without messing up the screen, while keeping the double sided tape i put on in place and intact.
just take your time and everything will go smoothly.
-edit- yes you will need some double sided tape because when you take the digitizer off the sticky layer of the tape goes with it, the rest of the tape stays on the screen and is impossible to get off without damaging your screen so you have to apply new tape over it.
i used some thin scotch brand double sided tape and i cut it into long narrow strips with a razor using my old digitizer as a cutting board, the same width as the original tape.

Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks

CraiGDaniel said:
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
Click to expand...
Click to collapse
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.

StevetotheH said:
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
Click to expand...
Click to collapse
um no they arent spacers...they are what directs the light to the 3 bottom keys. they are there for a reason so i recommend using them... ... now you are spot on with the 3m tape as it is the tape needed to do this whole job properly... the scotch crap is not made for this and WILL NOT HOLD UP NOR SEAL PROPERLY>>>
and for the person who said to put the tape over the old.... not a good idea... it can be removed and new should be used to replace the old..
sorry but i do this daily for a living so i do have a clue about this... just trying to help make it a successful repair and not one that ends up in my shop after the home repair failed and it damaged more than just the screen.....

Related

How to replace the Digitizer/Touch Panel? any body?

I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?

Help i need touch screen replacement guide for htc diamond

Hi i need a touch screen replacement guide for htc diamond
same here, anyone?
http://www.mediafire.com/?jnh4f2ndyzz
@mod: please remove this post if it is not allowed to post such links
http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond/
gmvmg said:
http://www.mediafire.com/?jnh4f2ndyzz
@mod: please remove this post if it is not allowed to post such links
Click to expand...
Click to collapse
check the wiki....points to the same link
Awesome... Thanks
Well i had the same issue and I had to give it to the service center and I got it back after 2 mnths yea i know it's a long time but i guess it was worth it in the end... but looking at how to do it urself I think it's a huge risk.... to even do it....
I've followed these steps and got to the last part. The service manua doesn't explain how to lift the LCD / touchscreen out (it's covered by grey tape). Does anyone know how to do the last steps?
I cant download that manual to see how far it goes but assuming you get as far as removing the 3 screws and removing the chassis plate to expose the rear of the LCD (can see the LCD part number 62H00004-31M)
All that holds the screen in now is adhesive, you can release this by, from the front, inserting an artists pallette knife around the sides and top and gently and progressively levering up to break the bond. Do not do this at the bottom or you will likely damage the flexi.
You now have an assembly which consists of a glass lens with the LCD bonded to the back and the digitiser bonded to the front, it is probably easier in the long run to replace this whole assembly.
To remove the digitiser lift the silver bonding tape and then the kapton tape from the digitiser connector (4 track connector) and de-solder the connector
To remove the digitiser from the front of the glass lens it is beneficial to heat it slightly (around 60 deg C). Then insert the pallette knife between the digitiser and the glass and slice it off - there is quite a lot of adhesive so take it carefully and do not lever as it may break the glass. Once the digitizer is off the glass needs to be cleaned of adhesive. Label removing fluid is good for this but ensure it doesn't get ino the LCD as it will ruin it.
All you need to do now is fit a new digitiser using optically clear adhesive-a tricky job unless you have a pressing fixture to ensure no air bubbles. I've also found that a lot of replacement Digitisers come complete with the glass lens and as it is impossible to remove the old LCD from the lens without cracking, they would seem pretty pointless to me?

Replace Digitizer only?

My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.

Cracked Glass Screen

A few days ago I cracked the glass screen on my Dinc. There wasn't any significant damage aside from the crack, and my LCD screen is working fine, so I ordered a replacement on Amazon thinking I could replace it. I found a screen which reviewers claimed came with the tools necessary to replace the screens, although the product did not advertise it as such. I made the order to find that the replacement did not come with any tools, and now I am stumped. Does anyone know where I can find cheap (and usable) tools to crack open my Dinc? I was hoping to finish this before I return to college in a few weeks and I'd rather not go back with a broken screen.
Thanks in advance!
Not sure what "tools" you're looking for, but there are only a few things you need to take your dinc apart (I just did this with mine):
1. T6 screwdriver to remove 4 screws on the big red cover
2. A small flat-head screwdriver to release block clips around the big red housing and pop it off. (also used to open up the ribbon cable clips)
3. small philips-head screwdriver to remove screws securing the main board and LCD
4. X-acto knife + hairdryer to remove the digitizer (the glass that you cracked)
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Sounds like you cracked the digitizer yet you ordered a new screen?
m52 power! said:
Sounds like you cracked the digitizer yet you ordered a new screen?
Click to expand...
Click to collapse
Although the sentence structure is somewhat ambiguous, it sounds like he bought the correct replacement part, a digitizer.
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
I'll vouch for this, it's the biggest headache to replace JUST the glass.
Since you already got the glass, you can go ahead and order a bezel by itself if you want... make sure you get one that has adhesive on the metal lip on the inside so the dust won't get in there
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
Exactly. I made the mistake of ordering JUST the screen and it was a complete headache. I subsequently ordered the frame/screen combo. Much easier.
Sent from my ADR6300 using XDA App
yeah i replaced mine but now i have trouble with the touch screen not working right. It randomly registers touches on the screen. Hope you don't run in to the same issue.
Glad to hear people are having success replacing these. I have a friend who's cracked his recently and will pass this thread on to him.
I replaced my screen with the digitizer/screen combo bought on amazon for under $20. it's a pain to install, but I found a good video on youtube and used their blowdryer method to make the glue more easy to manage and allow the screen to come off in fewer pieces. Also when you put the little ribbons back into their connectors make sure you get them all the way in - I had 256 color-like graphics for a little bit until I reconnected the screen properly
I've done it multiple times. I'm not clumsy, I just got the phone broken in the first place .
While it would make it easier to get the bezel, it can be done fine with just the digitizer.
They give you all the little plastic tools you need usually.
The last time I did it I used Krazy glue instead of very thin double sided tape.
I can answer any specific questions you have when replacing the digitizer if you want.
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal, but it annoys me a tiny bit that my phone isn't perfect.
Could you record the exact order in which you disassemble it? It might even help you out later
drizzt5;19538891
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal said:
I just replaced my screen tonight with an amazon digitizer kit and my trackball is also recessed. Might just open it back up and jam some leftover adhesive underneath it. I would recommend buying the frame though as it was a bit of a b*tch prying broken glass shards and adhesive from the thing. Would also make the phone look better as well..
Click to expand...
Click to collapse
i dont have a cracked screen but a very banged up bezel and battery cover. i calculated it and everything will cost me a total of $35 to replace. this includes the digitizer, bezel, battery cover and camera lens. cant wait to get this done.
thanks for the info on here.
Order the digitizer WITH the housing shell. I cracked my screen, too, and ordered the digitizer/screen only and ended up damaging my housing shell. The hairdryer trick is bogus and doesn't work very well, so spend the extra $10 to get the housing.
I was going to repare the screen to resell on Ebay, but since I broke the housing, I decided to just sell the actual AMOLED screen for $40. I'll find other parts I can sell, too, such as the motherboard and camera piece. Might actually end up making more money. Ah well.
I don't use Verizon anymore, which is why I ditched the DInc. Will miss it though. I do love HTC Sense. I have a Samsung Exhibit II now.
My first time doing this was with the digitizer only. Biggest mistake of my life! I could've made it work, but I was getting it replaced since it was bricked and superglue oozing out the sides might have raised some eyebrows. Digitizer+frame, void sticker, and 2 weeks later I had a "new" dinc.

[Q] Replacing digitizer

I've cracked the outer layer of glass on my optimus x2 which I assume is just the digitizer (I'm new to all this smartphone jazz but i've had alot of experience with building computers and such and i can follow instructions) and i'm guessing the cheapest way to repair this thing is to do it myself. I emailed LG asking about what they can do with it and they were asking for £20 just to look at the damn thing so i can't imagine actually doing any work on it would be cheap.
(can't post links but it was just some cheap generic one from amazon for £30)
I'm guessing something like this would do the job but I also need some special adhesive to get the LCD to stick to the digitizer am i right? I'm worried that it will not be as responsive or i'll do it wrong and i only recently dished out £250 for this so i'd like to try and do this right. I've watched a couple of videos on youtube which have helped a bit but none went right through the process so if anyone with any experience doing this could tell me about it i'd be very grateful.
its not that hard. everything just peels off when heated with a hair drier.
the digitzer should come with sticky strips which go around the outside of the lcd and stick to the out side of the digitizer.
Also try to get a digitizer with a frame already on it. otherwise youll have a little bit of a hard time trying to remove the glass from the frame, then gluing in the new one with adhesive.
http://www.youtube.com/watch?v=K77Xepb6yd8
Just follow this guide exactly, you should be fine man
Supupa said:
its not that hard. everything just peels off when heated with a hair drier.
the digitzer should come with sticky strips which go around the outside of the lcd and stick to the out side of the digitizer.
Also try to get a digitizer with a frame already on it. otherwise youll have a little bit of a hard time trying to remove the glass from the frame, then gluing in the new one with adhesive.
Just follow this guide exactly, you should be fine man
Click to expand...
Click to collapse
Thanks for the reply, that's a lot of help Could you recommend any retailer that sells these? I can't work out if any of the ones i'm looking at come with the sticky strips. Would I also not need any adhesive if it comes with the frame? I'm not sure I trust myself too much with doing that either.....
I recently replaced my digitizer. I ordered a digitizer already in housing off ebay, shipped from Hong Kong. I would strongly recommend buying it with housing, as it's often difficult to completely make sure that dust does not get between the digitizer and the screen when you're using adhesive tape.
When disassemblying the o2x, I found the adhesive sticking the LCD to the digitizer frame was too strong for the LCD to come off just like that (be careful, it's quite fragile). I heated the LCD a bit using a hair dryer, to make it come of easier. This has the added effect that enough adhesive may stick to the LCD, so you don't need to replace it when placing it in the new frame.
I only added a couple of adhesive strips to the top and bottom of the new frame before mouting the LCD. That was pretty stupid, cause the extra 0.1mm between the digitizer and the LCD means that when tilting the phone ~60 degrees to the sides, I can see the backlights at the sides of the screen. Surprisingly this doesn't seem to add any noticeable backlight bleeding though, so it's not a problem at all. However, I'd suggest to try and see if the LCD sticks to the frame with the old adhesive, before using adhesive strips. And if using adhesive strips, make sure you remove all the old adhesive from the LCD, and use adhesive strips all around the frame.
The only minor things to look out for are:
- Be very careful with the LCD! It takes very little flexing before getting dead stripes/areas.
- Careful with the plastic at the USB port - it's a bit difficult to get to fit, and it's quite thin, so I figure it will break easily.
- At the top of the phone, where the digitizer (or LCD, I don't remember) cable is mounted, there's a little grey rubber-thingy - it suddenly fell off my phone, and it took embarrassingly long to figure out where and how it fits
- The small backup battery (?) in the upper left corner of the phone is glued to the frame. I used a small flat-headed screw driver to release it from the frame. Don't try and remove it by yanking the flex cable.
But all in all, replacing the digitizer with a new one (already in a frame) was a quick and easy operation.
Edit: I bought this digitizer: ebay. co. uk/itm/T-Mobile-LG-P990-Optimus-2X-Replacement-Touch-Screen-Digitizer-Frame-ZVLT338-/160656180054?pt=UK_Replacement_Parts_Tools&hash=item2567dac356 and some cheap 2mm adhesive strips like ebay. co .uk/itm/3M-Sticker-tape-Adhesive-cellphone-touch-screen-LCD-2mm-HTC-Samsung-Sony-/200710386131?pt=UK_Mobiles_Accessories_RL&hash=item2ebb4571d3#ht_1099wt_1165
Why didn't I think of this before.. been cracks in my display for almost a half year now.
Local repair company said it takes two weeks to fix.. I had no plans to go two weeks without my phone
Just ordered one
p990 mother board
dear friend
sorry for my eanglish i write from italy.
i need your help but before i have to explane my problems:
i've a lg optimus x2 (p990) with water demage.....
i cleaned the mother board with success..now the phone turn on and fix the phone net and it can recognize the battery charge.
but unfortunately WI-FI,BLUETOOTH AND MIC(the people who call me can't hear me) DON'T WORK, THE GPS I DON'T KNOW BECAUSE I HOPE TO RESTORE THE WII-FI AND INSTAL GOOGLE MAPS.
i'm sure that wi-fi problems come from the mother board because i have an other same device so i made a test using the good one but the mic problems persisted
my question is ,do you know wich parts i have to check and clean again?
do you know where the wii-fi component are located in the mother board?
thanks for your attention
a friend
marco zavatta
Sorry for bringing up this old thread, but I have to ask, are all Optimus 2X digitizers the same? Don't some have different connectors or anything? Can I order any Optimus 2X digitizer for my P990? I was thinking of this digitizer, will it work?: http://www.amazon.co.uk/Digitizer-F...7BUA/ref=sr_1_1?ie=UTF8&qid=1364833172&sr=8-1
I had to replace mine recently, I read there are cheap ones where they only recognize 2 fingers instead of 5 like the genuine LG part. I ordered my digitizer from Ebay for around 18 british pound, I followed a few videos on Youtube with the disassembly, it's actually not that hard.
Keep in mind though that not all digitizers might come with glue attached or come with plastic tools, so keep a small bottle of glue and some plastic tools (credit card style plastic, knife) ready. One video recommends buying foam pads to glue around the digitizer, I didn't find that necessary, I just glued my new digitizer back onto the frame without problems. I accidentally made some glue residue onto the inside of mine, so make sure that you work very carefully
I have done this twice. It is not too hard and a lot cheaper. I follow this guide: http://www.youtube.com/watch?v=Po8hBaZt__o.
Do yourself a favour and buy a digitizer with bezel (which is a frame). The first I bought was ****ty Hong Kong digitizer, the second one good Polish(?): http://www.ebay.co.uk/sch/m.html?_nkw=p990&_sacat=0&_odkw=&_osacat=0&_armrs=1&_ssn=digitaloutlet.pl
The hardest part is not to get dust between digitizer and lcd screen - you could consider wearing gloves...
The second hardest part is not to bend bezel around usb inlet.
Good luck!
So there's no connector difference?
kaspar737 said:
So there's no connector difference?
Click to expand...
Click to collapse
The connector should fit any p990. If you are in doubt email the seller.
oneearleft said:
The connector should fit any p990. If you are in doubt email the seller.
Click to expand...
Click to collapse
Sorry for coming back to this rather old thread, but I have recently replaced the digitizer on my LG P990, bought on ebay shipped from Hongkong, following the video guide cited above. However the digitizer now works erratically with upper 1/4 not responding to touch, and sometimes the whole thing does not work, so I am unable to unlock the phone at all. The only thing that worried me during replacement was the thin layer of plastic film on the inner side, which teared off when removing protective layer (the film was extremely thin and fragile)-would this be the problem? Or the digitizer itself is of low quality?
Any suggestions appreciated.

Categories

Resources