Does anybody have a wiring diagram for the Captivate digitizer?
Working on a little project and need to know the pins for the digitizer output. Does anybody know if it's a four wire out?
If nothing else, a generic diagram might be enough.
Mods, if you please, this thread is a duplicate and should be deleted. My fault.
Related
Hey guys,
Does anyone have broken G1. My antenna cable is broken. I cant find this cable anywhere. This is the longer one. I will cover postage cost. I am from Poland. Please PM me. Thanks.
I really wish I could send you one.
But my parents would kill me.
You can wait 3 years when ill be 18 and able to make my own desicions
i have lots, but first may i ask how you broke it? were you trying to take it apart? or is it the board that is broken not the antenna?
or are you just talking about the wire? shorter wire for antenna board and longer wire going to the gps board
He's looking for the longer wire going to the board apparantly
The gps and antenna is easy to mix up....but I'm sure he got the "longer" part right
My longer wire is broken. I managed to put a screw through this wire.
http://www.ebay.com/itm/Htc-g1-/110809841104?pt=LH_DefaultDomain_0&hash=item19ccc7fdd0
here is a link for some parts on ebay, id recommend looking for something local. if you really cant find anything i guess i could send you the cable in an envelope.
shouldnt cost too much but i'd still require you paid for it
Hi everyone
recently the earphone jack of my Samsung Gt-5830i was damaged and im unable to get it repaired so if anyone is having the schematics and jumper diagram of GT-5830i please upload
Hi been having trouble with WiFi being very spotty, and thought it was because of the little Pig Tail antenna used, however after opening up the unit to solder in a proper antenna I found out that the reason it was so spotty is because the solder pad where the original antenna was soldered to was only hanging on because of some glue that had been applied.
I only realised this once the glue and solder had been removed.. exposing the now missing solder pad..
Looks like whoever did the QC spotted the loose solder joint so just put a blob of glue on there lol.
Does anyone know of an alternate location where i can solder in the new antenna? having just has laser surgery on my eyes I really dont want to spend a few hours tracing lines etc.
Its a Car Joying unit, Quad core 3188, 7" Tablet type with capacitive keys.
Maybe you should have posted this question in the Hardware forum section:
http://forum.xda-developers.com/android-auto/mtcb-hardware-development
themissionimpossible said:
Maybe you should have posted this question in the Hardware forum section:
http://forum.xda-developers.com/android-auto/mtcb-hardware-development
Click to expand...
Click to collapse
Good point :/
I have decided to get one of these ethernet adptors :-
http://www.amazon.co.uk/gp/product/...ue&ref_=ox_sc_act_title_1&smid=A1WCLLO809O2M2
And am going to hook it up to a small wireless bridge, will give me the range I want and is relatively cheap.
chuupa said:
Good point :/
I have decided to get one of these ethernet adptors :-
http://www.amazon.co.uk/gp/product/...ue&ref_=ox_sc_act_title_1&smid=A1WCLLO809O2M2
And am going to hook it up to a small wireless bridge, will give me the range I want and is relatively cheap.
Click to expand...
Click to collapse
@chuupa
Did this work out for you?
Hi,
I'm looking to replace my headphone jack after it was water damaged. Does anyone know where I can buy this module, every time I search online I only find part for Z3c. I don't think it's compatible judging by the pictures, can anyone confirm?
Any help will be highly appreciated.
Hey guys, i have been searching on ebay and on google, for a replacement charging port, but i can seem to find the correct one. Some show the charging port only and others whats seems to be the daugtherboard that holds the charging port. Has any of you order from here before? http://www.bluphoneparts.com/blu-vivo-xl-sub-pcba-with-charging-port/, they have the pcb with the charging port on it, but no image. any help will be greatly appreciated thank you.
I purchased the exact part that you linked and this fixed the charging port issue on my Vivo XL. Will need a bit of soldering skill to remove the speaker from the old board and solder onto the replacement board -- the solder pads are small, but not difficult if you have some experience. Two ribbon connectors need to be pulled up (2x small connectors, not the large metal -- that is a cover) and the board itself is attached to the frame by some adhesive.
Now the phone works great again -- well worth the $27 (w/shipping) to fix this common charging port issue.
advice
Hi did you get though with changing the port, my port needs changing but that part is no longer available, there is another site that is selling just the charge port. I have no idea how to change the port. I'm planning on asking someone with a soldering iron for help, is it difficult. Also with shipping to Trinidad the part is 22 us, there's a nexus 5x port on eBay for about 5 us , is there any chance that it will work.
Thanks
prettygirlleanna said:
Hi did you get though with changing the port, my port needs changing but that part is no longer available, there is another site that is selling just the charge port. I have no idea how to change the port. I'm planning on asking someone with a soldering iron for help, is it difficult. Also with shipping to Trinidad the part is 22 us, there's a nexus 5x port on eBay for about 5 us , is there any chance that it will work.
Thanks
Click to expand...
Click to collapse
I think I saw "just" the charging port when I was searching... looks pretty difficult to just change the port..
I got the little board that includes the charging port for about $27 US...
I just changed it and it was not very difficult.
You have to unsolder the old speaker wires and swap it to the new board... pretty easy...
Just don't let your soldering iron get very hot... test with a piece of very thin soldering wire to where it just melts.
Unplug your soldering iron to regulate heat..
You don't need to add any solder to reinstall.. there is some little dabs of solder on the board that should be enough.
Was for me.
Here's a video link...
https://youtu.be/NH_17vH4BfA
HI! Is there a way for me to get a sub pcba with charging port board? The website bluphoneparts has not been working for a long time. And I have searched on amazon and ebay with no luck.