Related
I have two PC's, one is a XP Media Center Edition. It had a virus on it and kept getting a corrupt file, so my techyish relative came and wiped the hard drive from scratch ( or so he says but it was a partial wipe) and reloaded the OS onto it. It worked fine, but then kept getting the corrupt file again. I then decided to order the recovery disks from HP, which is the computer manufactuer. They arrived and I put them in, followed the steps, and all wen well until I came to the recovery partition. It was backing everything up ( one time process only) into the recovery partition all fine and dandy until it came to a file that had to do with Microsoft Office. It stayed their for about 45 minutes backing up this file where the longest had been 10 minutes max for all the others. I looked the file up and it said it was a small 10 mb file, so I turned the computer off and went to normal without the recovery partition. Worked fine until one day something happened and I guess I needed to do the recovery again (it's been a few months since this has happened) and did all the steps, but it wouldn't take. It gets to about 4% and then dies with a BSOD and this message:
A problem has been detected and Windows has been shut down to prevent damage to your computer.
DATA_KERNAL_INPAGE_ERROR
If this is the first time you’ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps:
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical information:
*** STOP: 0x0000007A (0xE121F318, 0xC0000185, 0xBF8B6147, 0x1C610860)
*** win32k.sys – Address BF8B6147 base at BF800000, Datestamp 3b7de698
Copied it down word for word, space for space. Can anyone help me get this thing up and running again? It's now getting important.
Forgot to mention that I get the same problem each time I put the recovery disk in.
I'd recommend using a NON-Recovery Disk, but rather a Clean, Non-OEM, Windows Disk. If the issue pertains to the Kernal, it's usually unfixable without a Hard Boot of the Drive. You should do more than Re-Format.. you should delete all the partitions off of your Hard Drive with a Windows Disk, then pop in the Recovery Disks and do the OEM install.
So I need to wipe the hard drive clean again and put in another non OEM OS?
Not quite. Wipe the HDD clean with the NON-OEM Windows Disk, as most Recovery Disks do not allow you to alter the Partitions [Everything is done for you], then pop in your Recovery Disk and let it install the new Primary, and possibly the Recovery, Drives.
I see what your saying now, so what exactly happened to it?
Get Windows 7
I have windows 7, that's my other computer.
The guy at the un paso store got you too!!
At the step store? Lol.
PurpleLlamaLover said:
I see what your saying now, so what exactly happened to it?
Click to expand...
Click to collapse
When your supposed "Tech Savvy" friend attempted to fix your computer.. he, I'm assuming, did a simple "Repair" of the partition with an XP Disc. That is LITERALLY the most unwanted version of a fix ever... All it does is replace the system files, but keeps all of the other software that may have been conflicting with the system itself, BUT usually, all of the software is inaccessible. It's still on your computer, f*cking it up, but you can't see it.
Thus I always say, "If you get a bluescreen... more than once, and don't know what the code means... don't repair your computer.. re-format that b*tch after recreating the partitions."
But, if your XP compy has the specs to support Windows 7, your best bet, all in all, would be to install Windows 7. Doing so will save you the hassle of having to manually download all of the drivers for it... unlike installing a non OEM Windows XP [have to download & install the drivers manually].
PurpleLlamaLover
it sounds like the HP recovery disk could well be corrupt,
So you now have 3 options:
1. Try Linux Ubunut 10.4 LTS (Free Distro)
2. Buy a ligit copy of Windows 7
3. Download Windows Vista / 7 / XP from a torrent
and try untill you find a OS you lyk
Agent Zach said:
When your supposed "Tech Savvy" friend attempted to fix your computer.. he, I'm assuming, did a simple "Repair" of the partition with an XP Disc. That is LITERALLY the most unwanted version of a fix ever... All it does is replace the system files, but keeps all of the other software that may have been conflicting with the system itself, BUT usually, all of the software is inaccessible. It's still on your computer, f*cking it up, but you can't see it.
Thus I always say, "If you get a bluescreen... more than once, and don't know what the code means... don't repair your computer.. re-format that b*tch after recreating the partitions."
But, if your XP compy has the specs to support Windows 7, your best bet, all in all, would be to install Windows 7. Doing so will save you the hassle of having to manually download all of the drivers for it... unlike installing a non OEM Windows XP [have to download & install the drivers manually].
Click to expand...
Click to collapse
I'll try and get 7 for it. It was the last of the XP models, just before vista so i'd think it should be able to run 7. Think I need a new hard drive?
Bro that Simon_WM guys a genius. Listen to him.
Yea. This is my computer here, http://h10025.www1.hp.com/ewfrf/wc/...en&dlc=en&cc=us&product=3257746&lang=en#N1030
Think it'll run it?
PurpleLlamaLover said:
Yea. This is my computer here, http://h10025.www1.hp.com/ewfrf/wc/...en&dlc=en&cc=us&product=3257746&lang=en#N1030
Think it'll run it?
Click to expand...
Click to collapse
it may run with a lag
I just want it back up and running, I don't want vista though. On the little windows sticker is says "Vista Capable" but i've heard bad things about it, especially rom updating.
PurpleLlamaLover said:
I just want it back up and running, I don't want vista though. On the little windows sticker is says "Vista Capable" but i've heard bad things about it, especially rom updating.
Click to expand...
Click to collapse
ummm i use vista and have updated all my win mo phones on it...never had a problem
Really? Well, i'll keep in mind if I can't get XP back on it. I'd rather just have 7 and XP. I don't care what it runs as long as it runs again.
the best suggestion in this thread was install linux , however i take it that isn't a possibility. so here's what you need to do, you will require the following:
1) a fresh mind
2) a freshly burned copy of XPwhateverflavoryouwant
3) you do not care about anything on that drive.
put in freshly burned xp into computer, boot to cd drive, follow onscreen instructions, delete all partitions, create new NTFS partition, install to new partition.
if error comes back, it is not a software issue. fixing a xp bsod really is simple if it isnt hardware related.
editi guess sdcard is incorrect/confusing for my situation, it's the entire system up to root folders is stuck in a read-only type state.
I didn't really see anything that fits my current problem (sorry if there is an answer somewhere buried in here)
So to start off with info, I installed Android on the TP back in February for my fiancée just for the basics of email, videoplayer, comic reader, internet browsing. Nothing too extravagant, just something with more to offer than webos.
I never did any updates on it because it worked perfectly fine for what it was being used on.
I've changed out the video selection many times as she watches through the shows with no problems.
Now I go to change the files and I delete them, add the new stuff, all seems fine. Then I unmount it and everything I deleted is back and everything I added is gone. I've uninstalled apps and they come back, I've done updates to apps and they revert back to before the update.
I've gone into CMW and done the wipes and even formatted sdcard, cache, etc. Nothing works. Even mounting USB in CWM to add files gives the same result of them disappearing right after it is unmounted.
I've tried ACMEUnistaller but it doesn't work. I saw something flash by the screen about something failing, but it goes too fast to even really see what it's about.
Sorry this is so long. I appreciate any insight!
Kernel
2.6.35-palm-tenderloin
[email protected]ost #12
CyanogenMod version:
9.0.0-RC0-Touchpad-alpha2
Build Date
Mon, Feb 20 13:59:21 CST 2012
Build Number
IML74K
plasticsoldier said:
I didn't really see anything that fits my current problem (sorry if there is an answer somewhere buried in here)
So to start off with info, I installed Android on the TP back in February for my fiancée just for the basics of email, videoplayer, comic reader, internet browsing. Nothing too extravagant, just something with more to offer than webos.
I never did any updates on it because it worked perfectly fine for what it was being used on.
I've changed out the video selection many times as she watches through the shows with no problems.
Now I go to change the files and I delete them, add the new stuff, all seems fine. Then I unmount it and everything I deleted is back and everything I added is gone. I've uninstalled apps and they come back, I've done updates to apps and they revert back to before the update.
I've gone into CMW and done the wipes and even formatted sdcard, cache, etc. Nothing works. Even mounting USB in CWM to add files gives the same result of them disappearing right after it is unmounted.
I've tried ACMEUnistaller but it doesn't work. I saw something flash by the screen about something failing, but it goes too fast to even really see what it's about.
Sorry this is so long. I appreciate any insight!
Kernel
2.6.35-palm-tenderloin
[email protected] #12
CyanogenMod version:
9.0.0-RC0-Touchpad-alpha2
Build Date
Mon, Feb 20 13:59:21 CST 2012
Build Number
IML74K
Click to expand...
Click to collapse
I've run across this 3 times with TPs I work on....
1st one had to be sent back to HP because somehow internal memory was damaged and got locked in some some of read only mode
2nd one I saw, I went into webOS, installed the internalz app, mounted the TP to the computer, then added and erased some files and from then on all was good in both webOS and Android
3rd and 4th (same customer) had to be sent in to HP
Now let me mention I live in Costa Rica so all these have been exposed to several scans at airport security checkpoints. I mention this because I haven't seen anything close to a read only problem with the TPs in the USA
Sent from my aokp_tenderloin using Tapatalk 2
thank you so much for the info. Unfortunately Internalz didn't want to help the items stay deleted either. The stuck in read-only type mode is very weird.
I'm pretty sure I am 3 weeks out of the 1-year warranty on it, plus I am unable to remove android from it to even trick them that it just doesn't work.
I guess I'll try webos doctor and see if that can get it going.
edit: webos doctor not working, even with the closing it at 8-12% tricks and doing the lvm.static..... stuff... 'cause it of course doesn't see to actually delete anything... i'll have to double check tomorrow when i bought it, pretty sure it's over the year and since it turns on and has android kinda screwed
plasticsoldier said:
thank you so much for the info. Unfortunately Internalz didn't want to help the items stay deleted either. The stuck in read-only type mode is very weird.
I'm pretty sure I am 3 weeks out of the 1-year warranty on it, plus I am unable to remove android from it to even trick them that it just doesn't work.
I guess I'll try webos doctor and see if that can get it going.
edit: webos doctor not working, even with the closing it at 8-12% tricks and doing the lvm.static..... stuff... 'cause it of course doesn't see to actually delete anything... i'll have to double check tomorrow when i bought it, pretty sure it's over the year and since it turns on and has android kinda screwed
Click to expand...
Click to collapse
I would suggest trying to restore down to WebOS 3.0. In that procedure you literally wipe EVERYTHING on the internal partitions in novaterm and start from absolute scratch. Therefore, if it a software issue you could solve the problem. However, if it is a hardware issue, you'd be kinda screwed.
Yeah, none of the methods I've ended up finding about this problem or other bricked problems are working at all.
i checked at work when i bought it, which of course the 11th was the year mark... but I do have android installed so even if i can get any chance of them honouring it so close they'll probably be like "oh you have android, that'll be $$$ for us to do anything. thanks!"
So I guess I now I have a paperweight with some features.
cdzo72 said:
I've run across this 3 times with TPs I work on....
1st one had to be sent back to HP because somehow internal memory was damaged and got locked in some some of read only mode
2nd one I saw, I went into webOS, installed the internalz app, mounted the TP to the computer, then added and erased some files and from then on all was good in both webOS and Android
3rd and 4th (same customer) had to be sent in to HP
Now let me mention I live in Costa Rica so all these have been exposed to several scans at airport security checkpoints. I mention this because I haven't seen anything close to a read only problem with the TPs in the USA
Sent from my aokp_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
When you got the tablets back had they been fixed or were they refurbs ? Did HP say anything about Android still being on it?
There is a thread in the General forum about how to restore and downgrade. Have you tried that thread ? It is usually a great way to try and get that last restore before sending it back to HP.
73 de VE6AY
Sent from my HP Touchpad, running the latest CM9 nightly, from the XDA Premium App
how are you adding and deleting files when in android? which version of android do you have installed? have you tried different rom versions? have you tried moving and/or deleting files over adb? are you using windows or linux on your computer that youre connecting the touchpad to? it doesnt make sense that the sdcard would be set to read only. is it only certain folders that you cant modify the contents of, or is it the entire sdcard? are you able to modify contents of folders in the / directory of the device using root file explorer or es file explorer in android? have you run "fix permissions"? Also, running webosdoctor wont wipe the sdcard contents or format the sdcard in any way. its going to change the data in the webos partition and may change some data in the /boot directory.
sstar said:
When you got the tablets back had they been fixed or were they refurbs ? Did HP say anything about Android still being on it?
Click to expand...
Click to collapse
They had been fixed but the owners sent them off and had to pay for the whole thing because they had Android on them. When I got my hands on them again I just reinstalled Android. HP charged a little over a hundred dollars for the fix
Sent from my aokp_tenderloin using Tapatalk 2
cdzo72 said:
They had been fixed but the owners sent them off and had to pay for the whole thing because they had Android on them. When I got my hands on them again I just reinstalled Android. HP charged a little over a hundred dollars for the fix
Sent from my aokp_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
Thanks for the answer, this would tend to suggest that the problem is software based corrupted or otherwise. I am trying to find a program that will allow me to read/format the Android partition on my windows computer and will let you know if come up with anything.
Regards
i guess i should change the title slightly.. it's not sdcard, but basically the entire touchpad contents. go to root and delete whatever i want and it doesn't matter. connect it and format with windows and it doesn't actually matter.
haxin said:
how are you adding and deleting files when in android?
Click to expand...
Click to collapse
i've added and deleted just by using mtp. i've also deleted the files on the android side with the video player (vplayer) i've installed es file explorer (which after restart is gone) and deleted with that. i've also gone into webos and installed internalz pro and deleted files that way, which it then seems to work until i of course do anything related to restarting.
some of the files i've put on, i've had it recognize briefly. so for the video file, start it, then it gets really choppy/glitchy playing it. so stop it, go back into the vplayer and it's back to the old stuff
which version of android do you have installed? have you tried different rom versions?
Click to expand...
Click to collapse
android version 4.0.3. nothing else will install. if i add files while in android, when i boot into cwm they are gone. if i mount usb in cwm and add them they stay briefly but when i try to flash them they fail.
have you tried moving and/or deleting files over adb? are you using windows or linux on your computer that youre connecting the touchpad to?
Click to expand...
Click to collapse
i have not tried adb yet, just not as familiar using it properly, i will give it a try though.
i am using windows 7 on my laptop currently. i do have a pc upstairs that i barely use that has vista, but i don't know how that would make a difference to the touchpad
it doesnt make sense that the sdcard would be set to read only. is it only certain folders that you cant modify the contents of, or is it the entire sdcard?
Click to expand...
Click to collapse
yeah as i put above i guess saying sdcard was a bit confusing/misleading (my bad, sorry!), i didn't really know what else to call it at the time or how to explain myself properly at first.
are you able to modify contents of folders in the / directory of the device using root file explorer or es file explorer in android?
Click to expand...
Click to collapse
i can move/delete/modify anything which has absolutely no effect to the device. i've used es file explorer and gone up to root and deleted everything and the system runs fine. says the system is empty with lots of free space (its the 32gb model) but restart or even go into recovery and everything is once again there.
have you run "fix permissions"?
Click to expand...
Click to collapse
i've run it a few times. just acts likes it's working and then says done. i've even gone into the mounts and storage in cwm and formatted sdcard/cache/data/system. does nothing at all in the end of things
Also, running webosdoctor wont wipe the sdcard contents or format the sdcard in any way. its going to change the data in the webos partition and may change some data in the /boot directory.
Click to expand...
Click to collapse
it was just something to try to get somewhere right. it never gets past 12%. always fails to reboot.
I am currently letting the battery drain and see if it dying and then being charged will do anything. probably not. but who knows. i talked to a "tech" on the chat support (i never mentioned android) who told me that having preware installed in webos causing it to become corrupt and they "don't knowledge of preware installed devices" exact words. no idea what that means haha don't have knowledge, don't acknowledge...
anyhow. i've not quite given up. i just don't really see it turning out any differently from the previous times. i do appreciate all the feedback and help very much though
ok so heres what I would try. First try flashing a new fresh rom. download one that you want to your computer like cm9 nightly or aokp or whatever you feel like. then boot into CWM recovery connect the touchpad to the computer via usb. then connect to the touchpad with adb. I'm not sure how to do this in windows because it's been so long since I've done it on a windows box, I always use linux.
adb has alot of options, you can move files to and from the device, you can uninstall or install app packages, and more. this way you can adb push the rom .zip to the touchpad's sdcard while youre in cwm recovery. this way you dont have to reboot the touchpad and risk having the file disappear, you can just go to 'install zip from sdcard' and then 'choose zip from sdcard' in cwm recovery after you adb push the rom, you should see it in the folder you pushed it to on the sdcard.
If you arent familiar with how to use adb from the command line or the terminal this might not make alot of sense and i dont know how better to explain it than that. Also yes windows 7 vs windows vista does make a difference there are issues with novacom installing properly, that's why you would have problems running acmeuninstaller or acmeinstaller2. if you look around you should find some videos or how to's that can probably explain it better. Hope this helps.
http://www.webos-internals.org/wiki/Novacom_with_Windows_7
http://forums.webosnation.com/webos-internals/295881-webos-doctor-12-issue-fixed-5.html
http://forum.xda-developers.com/showthread.php?t=1426244 is the thread I was talking about - it allows you to access the hard root of the device, repartition it, and start again from scratch. It is what I was suggesting last night, from my tablet when I didn't have the link handy.
ve6ay said:
http://forum.xda-developers.com/showthread.php?t=1426244 is the thread I was talking about - it allows you to access the hard root of the device, repartition it, and start again from scratch. It is what I was suggesting last night, from my tablet when I didn't have the link handy.
Click to expand...
Click to collapse
Probably the best suggestion yet given that everything else has been tried.
Good luck.
****EDIT****
Before you attempt the step above I have just noticed a difference between between cwm and. TWRP2.2 which I have installed on my Touchpad via goo manager. If I open recovery via goo manager and then select wipe it gives me 4 options cache, davlik, factory reset AND system which i think says will remove your rom . I don't see the forth option available with the regular cwm/clockwork. Just a thought.
All the best with whatever you try next.
sstar said:
Probably the best suggestion yet given that everything else has been tried.
Good luck.
Click to expand...
Click to collapse
this would work, however you have to fix you novacom/novaterm issues on your windows machine before you'll be able to do any of this. the reason acmeuninstaller, acmeinstaller2 arent working is likely because youre on a windows7 64bit box and Palm-sdk, the novacomd.exe, noverm.exe, and javaruntime apps and drivers arent setup right. just make sure you have the proper javaupdates on your computer then you can install preware in webos, preware has some nice tools that will delete the entire android install partitions, one is called 'remove android' and the other is called 'tailor' you run them from within webos. after you do that then in webos you should do a full device reset. you'll find it in the "info" tab under settings in webos. this will delete and reformat the whole /media ,(aka sdcard) partition. so you will lose all the files you have stored on both webos and android. that format will take a long time probably like 30 min or more. after thats done. reboot the hp and run webosdoctor. now i know for sure this will work because ive done it on mine. remember to put the touchpad in developer mode in webos first to install preware. you can do that by typing webos20090606 into the webos search bar and hitting enter. I'll put links from my box.com accou t to everything you need.
https://www.box.com/s/479acdb6ef9c99fc7b92
https://www.box.com/s/1aed4722990aad251570
edit: also I'm not sure if youre on the 16gig 32gig or 64gig pad, the webosdoctor that i linked is for 32gig wifi only US version. if thats not what you have then youll need to get the doctor for for specific touchpad. or you could create a webosmetadoctor but thats a whole nother project.
i have the 32gb version. i assume US and Canadian aren't gonna make a difference
i've tried all those threads. any novacom/novaterm stuff doesn't work, the files won't delete so when trying to recreate they just error saying it already exists.
if the devices is on in androind the adb can find the device although the "Serial" has a bunch of ???? at the end of it. when i go to cwm adb cannot find the device.
in cwm i can mount and add files that way and go back to install zip sdcard but get:
Code:
--Installing /sdcard/aokp_tenderloin_milestone-4.zip
Finding update package...
Opening update package...
E: Can't open /sdcard/aokp_tenderloin_milestone-4.zip
(bad)
Installation aborted
used "remove android" in webos, but then nothing is different after the fact as usual. 'tailor' doesn't seem to exist anymore in preware at least that i can find
not sure if there is anything else I can do at this point
plasticsoldier said:
i have the 32gb version. i assume US and Canadian aren't gonna make a difference
i've tried all those threads. any novacom/novaterm stuff doesn't work, the files won't delete so when trying to recreate they just error saying it already exists.
if the devices is on in androind the adb can find the device although the "Serial" has a bunch of ???? at the end of it. when i go to cwm adb cannot find the device.
in cwm i can mount and add files that way and go back to install zip sdcard but get:
Code:
--Installing /sdcard/aokp_tenderloin_milestone-4.zip
Finding update package...
Opening update package...
E: Can't open /sdcard/aokp_tenderloin_milestone-4.zip
(bad)
Installation aborted
used "remove android" in webos, but then nothing is different after the fact as usual. 'tailor' doesn't seem to exist anymore in preware at least that i can find
not sure if there is anything else I can do at this point
Click to expand...
Click to collapse
ok no one will be able to help you fix this issue unless you give complete details of the problems. when you say " novacom/novaterm stuff doesn't work" we cant really help specific error details is what i need. I dont mind helping you fix this but you have to be a little more specific on exactly what,where, and how youre installing and running and mounting apps and directories.
your problem IS fixable but you need to slow down and really do things exactly step by step.
Ok so back to ./adb. now when you boot in to CWM recovery on he touchpad DONT do anything in CWM just plug it into the computer. do not mount it as a usb storage and dont mount or unmount the sd partition LEAVE IT.
you can then use ./adb from the command line or terminal on the computer to move the files to the touchpad' or install apk's uninstall apk's you name it. This will require that you know some linux terminal commands. for example to move a new rom zip to the internal sd card or into any other folder you can use ./adb push command to run a root shell on the android device itself you can use ./adb shell and then change folder and file properties from readonly to rw. this can all be done while the touchpad is patiently waitng in CWM recovery. this way when youre done installing or uninstalling apps from the device and moving flash zips to it, you can disconnect the .adb connection with ./adb disconnect or just type exit from the terminal till it closes. unplug it then you will be able to pick up the touchpad and install zip from the sdcard, keep in mind you dont want to choose 'apply u[date from sdcard' you want to use the 'install zip from sdcard option' you can read up more on how adb works. it is probally the most important part of hacking android.
with that being said. novaterm is the palm webos version of .adb. this is why when you boot into webos recovery to do things like acmeinstaller and acmeuninstaller2 the novaterm novacom and novacomd apps have to be installed correctly on the computer or else you wont be going anywhere fast. some screenshot examples of how it should appear below.
https://www.box.com/s/432e63a83215f00eea6a
https://www.box.com/s/970bc29542a05f98f036
https://www.box.com/s/63c0f656e8354f7f2d6a
https://www.box.com/s/cbe3266467ae8e3ebabe
https://www.box.com/s/005e56a61a178dd17fa4 some better resolution images.
Plasticsoldier said
used "remove android" in webos, but then nothing is different after the fact as usual. 'tailor' doesn't seem to exist anymore in preware at least that i can find
not sure if there is anything else I can do at this point
Yes there is
Firstly tailor does exist, it is a beta and the facility to dl must be enabled.
Read this and scroll down to Enabling beta test feeds and follow the instructions , when you get as far as using the Linux command you CAN copy and paste thank God.
http://en.m.webos-internals.org/wiki/Testing_Feeds?wasRedirected=true . After that reboot into Webos and launch preware. Go into managed feeds as per the instructions in the link above and install Tailor. Reboot again and the app will work. It looks very good actually.
But before attempting to actually use Tailor please read the article I have posted below it is only 7 pages long but will explain how to use Taylor properly as it is a powerful tool.
http://forums.webosnation.com/webos...partition-filesystem-editor-beta-testing.html
I have done all of this , this morning so if you have any problems pm me or ask in this thread.
I sincerely hope that this helps, it should be the answer to your problems.
@haxin: sorry, wasn't trying to be unhelpful when everyone is being helpful to me. I shall be more detailed in future responses. I think i was getting frustrated and had had a busy exhausting day so it didn't help me come across clearly/properly.
OK, so I had preware installed already, so I removed it, went into developer mode, used the linux commands, reinstalled preware, added Tailor.
(i've done this a few times, because I didn't remove the cable after doing the linux commands for preware, then i accidentally hit the wrong buttons and it connected to 'usb drive' mode and wouldn't connect on the pc side and got stuck on the "ow disconnected me properly next time" screen).
So it gives me the following options
USB (media)
Android (system)
Android (cache)
Android (data)
Unused Space
the 'usb media' starts mounted and will mount again if unmounted. If I use 'check filesystem' it'll pass. So then I try 'delete partition' which pretends to delete, then it takes me to the unused partition which is still at 16mb. so i try to use "check filesystem' again and it fails. try repair and it fails as well
I've tried mounting the android parts just to see, they just sit there processing that they are trying to mount. trying to delete or anything else fails as well.
and now after trying things, any of the 'cards' will try to open and just sit there grey. and with my usb cable not plugged in it still is giving me the option to enter usb drive mode. and with this i have to restart and go through the steps again of adding Tailor which is getting tedious.
I restarted, went through the motions to get back to Tailor. trying out resizing just to see how that goes. So far 15%. not sure what will happen when done, but we will see.
This is getting long, so i'll end this part and update on anything and also try to familiarize myself with adb a tad more
Hi all,
I hope you can help as something very strange and unusual has happened to my Galaxy S3 LTE i9305 (on Orange in UK). Samsung technical support tell me they've not heard of the issue before as do the official repair shop. I have never installed any unusual software or tried to access the internals etc.
On Sat 26th Oct, in the evening, the phone was connected via USB to my laptop charging. There was no data transfer taking place, and the laptop was idle. The phone was not in use, nor was I nearby but randomly it showed the Samsung splash screen logo - it looked a little weird as it was pure black but with random speckles of coloured dots (which made it look like a Galaxy - I thought perhaps I hadn't noticed it before). I was unable to reset so took the battery out and replaced. It did the same thing and then on the second time of removing hte battery the screen became completely white with black marks generating a fuzzy effect - it's been like this ever since.
I get the white fuzzy screen if attempting to turn the phone on, or attempting to recovery mode, however if going to the install option (which I assume happens before Android boots), the screen is absolutely fine and proves not to be at fault. I should add the screen is cracked slightly, it has been since April and is not the cause of this random error.
Tech support tell me that they'll happily accept it back but ultimately, they will wipe the phone and send back as reconditioned. I've tried to connect via Kies, device not found - nor is it when connected to a computer - infact the computer tries to 'install device drivers'.
I'm sure everyone says this however I am an organiser of a large local festival in the UK and the phone has some very important detail storesd in the ColourNote app which I need to access - also the contacts appear not to have synced with GMail since May.... I'm desperate to access these files, for money too potentially, but cannot afford to go down the simple, wipe and reformat easy option. Can you help? Do you know any software that can access data from the internal memory card (note I've removed the external card which contained the photos) How about once the phone has been wiped, to try and see if anything can be recovered then.
Would really appreciate your support, this developer community is my last option and you're normally so awesome, as can't find any reference to the problem online.
Is your colour note app not synced ??
You can try RECUVA data recover.
You need to read the faqs and guides first .
Including the one that covers storage and recovery ..
Samsung reject warranty on phones that have damaged screen .
JJEgan said:
Is your colour note app not synced ??
You can try RECUVA data recover.
You need to read the faqs and guides first .
Including the one that covers storage and recovery ..
Samsung reject warranty on phones that have damaged screen .
Click to expand...
Click to collapse
Hi,
....no I had never set it up. So ironic that was on the to do list in the app.
I'll look into Recuva, is that for before or after I send it off. Is there much chance do you think?
Yes, sorry. I meant to say I also have phone insurance which covers the screen so will have it off to them first, and then onto Samsung - ie 2 places of data wiping!
Thanks for your reply though,
Kind of hoping I may just be able to fix the problem, even if only temporary, but realise it's unlikely
s_boddy said:
Kind of hoping I may just be able to fix the problem, even if only temporary, but realise it's unlikely
Click to expand...
Click to collapse
Hi mate,
You can try flashing just the system (and boot) images if you think it's a software issue.
That way your data partition will be intact.
Instructions:
Step 1) Download the Stock ROM you want to use
Step 2) Rename the file from .tar.md5 to just .tar
Step 3) Open the .tar with WinRAR or something similar
Step 4) Extract: system.img (and boot.img if you want the Kernel)
Step 5) Create ODIN file from .img files http://forum.xda-developers.com/showthread.php?t=1484304
Step 6) Flash the new ODIN file to restore your firmware to Stock!
On Windows you can use Cygwin to run these commands if you don't have access to Linux.
NOTE 1: That guide uses recovery.img as an example but you can replace that text with system.img on the first line.
NOTE 2: If you are adding more than one file (eg. system.img & boot.img) simply list them one after the other with a space between each file.
NOTE 3: Do not include data.img, it WILL wipe your data! Do not include cache.img, hidden.img, these MAY wipe your data!
Best of luck, I hope this helps you out :fingers-crossed:
Have a great day!
-Shaz
So, here’s how you can recover data from a Soft-Bricked Android smartphone:
1. Once you’ve installed a custom recovery on your device, open it using the specific method for your device. E.g for Samsung you can turn off the device completely, then turn it on by pressing and holding Volume Up + Home + Power Key and you will be able to access the recovery. These methods vary for different devices.
2. Once in CWM or TWRP Recovery you will find a number of options.
For CWM Recovery, select “Mounts & Storage > Yes”.
In Mounts and Storage menu you will find some more options, from the list select “Mount USB Storage or the option depending upon your choice.”.
Now connect your phone to your PC using the data cable.
As soon as you connect your phone to your PC, the USB Storage / Internal Storage will open up in folder view.
You can copy all of your files to your PC now.
3. For TWRP Recovery, Select “Mount > USB Storage”.
Connect your phone to your PC and it will open up the USB / Internal Storage.
3. Copy your desired files.
That’s all! You can easily recovery all of your data stored on the internal storage of your Android device.
Hey guys. Sorry to bother you in the X98 section, but since there's no section for the X80 yet and maybe the devices have some similarities, I hope it's ok.
The tablet worked fine, but to remove any possible bloatware under Windows or Android, I reset Windows. Somehow the device must have crashed (low battery?) and now I can't boot to Windows anymore (black screen and / or boot loop). Of course I made no backup / recovery disk. Android still works fine and I still get into BIOS / UEFI.
I tried reinstalling Windows via OTG with USB stick. I got to the point where I can choose a partition. Problem is, there are lots of partitions (Android, recovery, System and so on). I located the Windows partition, formatted / deleted it and tried to reinstall Windows on this partition. Just the exact way I would do it on a PC. Somehow it won't install on this partition. The error message says something about "the partitions are not in the recommended order. Further information for installation on GPT-volumes..." (I don't know the exact English phrasing because everything is in German). I chose "continue anyway". Then I get the message that "the EFI-system is not formatted in NTFS. Format the partition to FAT32 and start install procedure again". I press ok and get back to Windows Setup (Install now).
I also tried different repair and recovery options. One time I got error code 0xC0000034. Funny thing is, Windows still seems to be there because while trying to repair / recover I tried to load some drivers and could see the hard drives and folders under Windows.
I tried downloading the original roms here: http://pan.baidu.com/s/1qYEa8gc
You need a Baidu account for the larger files and after days and days I gave up to create such an account as it seems to work only with a mainland China number. There's an option for oversea mobiles but that's not working. I tried a QQ-account, but Baidu wants to link with it and you need that telephone number again. So apparently there's no way to get the original files that way.
I found some stuff here: http://www.needrom.com/download/teclast-x80-pro-dualboot/ but that's only a tutorial file in Chinese and some flash programms / drivers (also got them from Baidu - smaller files are possible to download without an account).
Long story short: I guess recovering Windows 10 is too much effort, so I want to make the tablet Android only and of course want to use the whole capacity for Android. I found a thread on reddit about removing Windows on the X98: https://www.reddit.com/r/teclast/comments/479eua/teclast_x89_how_to_remove_windows_10/
But I have no idea which partitions are definitely needed for Android and which ones I can safely delete. I found a partition map here: http://wheresmykeyboard.com/2015/08/teclast-x98-air-64gb-dual-boot-default-partition-map/ but that doesn't help me that much because they look different.
Attached you will find a photo of all the partitions on my device. I guess there are some which were created during the failed Windows installation because I had about 20 GB free space and now only 17.7 GB.
So is there anybody out there who knows if it's possible to remove Windows completely and which partitions I have to delete?
Did you ever figure this out? I just bought an X80 Pro and was thinking of doing something similar since I plan on making it an android-only tablet.
Deathgazer said:
Did you ever figure this out? I just bought an X80 Pro and was thinking of doing something similar since I plan on making it an android-only tablet.
Click to expand...
Click to collapse
Hi. Sorry for the late replay. Yes, I figured it out and my X80 Pro is now running Android-only with 32 GB. In the end, it wasn't that hard but a long way to success.
metalaxi said:
Hi. Sorry for the late replay. Yes, I figured it out and my X80 Pro is now running Android-only with 32 GB. In the end, it wasn't that hard but a long way to success.
Click to expand...
Click to collapse
Please do describe how you achieved Android-only with 32 GB memory
Cheers
metalaxi said:
Hi. Sorry for the late replay. Yes, I figured it out and my X80 Pro is now running Android-only with 32 GB. In the end, it wasn't that hard but a long way to success.
Click to expand...
Click to collapse
Yes please tell us how metalaxi , it'll be much appreciated.:good:
Ok, guys. Since some of you are asking how I did it, I'm going to try to explain it. It's kinda embarrassing that I don't remember the exact way but I hope it helps somehow. I used the tutorial from this site: http://techtablets.com/forum/topic/x80-plus-android-os-only/#login
Even though it's supposed to be for the Plus model, it also worked on the Pro. Btw, the guy Alex in that thread is me .
You can download all the files from my Google Drive here: https://drive.google.com/open?id=0BxEFqy4Rt9w_cnh3VG9ySk5sOHM
You need
- Android5.1 Upgrade Tool.rar
- X80 Pro (E3E6)- Dual OS - Android5.1-V1.04 Firmware.rar
- gpt.rar (Credit goes to Allember @techtablets-forum; hope it's ok to spread the file)
First you have to install the flash tool. Unrar the firmware and replace the gpt.bin. Then flash the firmware by checking BLANK.
Problem is that when I did all that, my Windows was already crushed and wasn't working anymore. I can't remember anymore if I erased the Windows partitions or any others beforehand. If you're not interested in Windows anymore, just flash it without changing or erasing any of the partitions. I guess by replacing the gpt-file, you do all that automatically.
I hope this somehow helps you. Feel free to ask for more help.
Have a good night!
metalaxi said:
Ok, guys. Since some of you are asking how I did it, I'm going to try to explain it. It's kinda embarrassing that I don't remember the exact way but I hope it helps somehow. I used the tutorial from this site: http://techtablets.com/forum/topic/x80-plus-android-os-only/#login
Even though it's supposed to be for the Plus model, it also worked on the Pro. Btw, the guy Alex in that thread is me .
You can download all the files from my Google Drive here: https://drive.google.com/open?id=0BxEFqy4Rt9w_cnh3VG9ySk5sOHM
You need
- Android5.1 Upgrade Tool.rar
- X80 Pro (E3E6)- Dual OS - Android5.1-V1.04 Firmware.rar
- gpt.rar (Credit goes to Allember @techtablets-forum; hope it's ok to spread the file)
First you have to install the flash tool. Unrar the firmware and replace the gpt.bin. Then flash the firmware by checking BLANK.
Problem is that when I did all that, my Windows was already crushed and wasn't working anymore. I can't remember anymore if I erased the Windows partitions or any others beforehand. If you're not interested in Windows anymore, just flash it without changing or erasing any of the partitions. I guess by replacing the gpt-file, you do all that automatically.
I hope this somehow helps you. Feel free to ask for more help.
Have a good night!
Click to expand...
Click to collapse
Hi @metalaxi. Do you think its possible to like "reverse" and use the same files to remove Android instead and maintain the Windows 10? Appreciate to hear from you. Thanks!
Do we have to change the gpt before doing what you said in your PDF? Or I have just to follow your PDF?
Hi guys, got mine a few months and want to get rid of the Windows part, but the instructions are insufficient for a joker like me.....
1. Download the firmware, its 4 parts of rar being zipped together
2. flash the firmware HOW?!?!?! I have no Idea...... please give us some closer instructions.
reycharlesconrad said:
Hi @metalaxi. Do you think its possible to like "reverse" and use the same files to remove Android instead and maintain the Windows 10? Appreciate to hear from you. Thanks!
Click to expand...
Click to collapse
Sorry, I can't answer that sufficent enough. As far as I know, you can just delete all partitions except the ones from Windows. Then format the unallocated space and merge it with the one from Windows. No guarantee!
dirkzelf said:
Hi guys, got mine a few months and want to get rid of the Windows part, but the instructions are insufficient for a joker like me.....
1. Download the firmware, its 4 parts of rar being zipped together
2. flash the firmware HOW?!?!?! I have no Idea...... please give us some closer instructions.
Click to expand...
Click to collapse
1. Which 4 parts do you mean?
2. To flash any firmware, you need to install all the upgrade tools:
IntelAndroidDrvSetup1.5.0
iSocUSB-Driver-Setup-1.2.0
PhoneFlashTool_5.3.4.0_internal_win32
metalaxi said:
1. Which 4 parts do you mean?
2. To flash any firmware, you need to install all the upgrade tools:
IntelAndroidDrvSetup1.5.0
iSocUSB-Driver-Setup-1.2.0
PhoneFlashTool_5.3.4.0_internal_win32
Click to expand...
Click to collapse
it's too long ago, so I don't know what I exactly did there, but since there was no reply for a long time, I just took a shot and worked out well, now I have an Android only tablet.
I just got lucky I guess....
partition help
Hi, please help.
I have x80pro e3e8
I managed to erase a complete disk partition.
You are trying to revive again, fail.
installed here:
iSocUSB-Driver-Setup-1.2.0
IntelAndroidDrvSetup1.5.0
PhoneFlashTool_5.3.4.0_internal_win32
downloaded here:
Firmware (20161020_SZ)
Tablet joined and tried to flash.
* failed - failed loadet.efi
Please help. I can not download from Baidu
* If I use phoneFlasTool and flash a blank disc - Create Flash partition and dual boot and replace recovery?
What to do with an empty disc?
Thanks for any advice
It is not so hard. By mine it was only trial and error. Installiert all drivers an go in the bootloader with three Finger method. Go two levels up and go into bootloader. Then connect to PC and look in Intel flashing tool if connection is reconiced correctly. Select the downloaded file and select flash. Thats it. Device will reboot and you are ready to go.
theone0987654321 said:
It is not so hard. By mine it was only trial and error. Installiert all drivers an go in the bootloader with three Finger method. Go two levels up and go into bootloader. Then connect to PC and look in Intel flashing tool if connection is reconiced correctly. Select the downloaded file and select flash. Thats it. Device will reboot and you are ready to go.
Click to expand...
Click to collapse
Thank you for the advice. That's right, I did it was marked. I found a reason. rom file was saved on desktop, and had a long name (as I downloaded it) It must copy the file to C've renamed the firmware. Everything went alright. I downloaded and used the GPT files for resizing disk and now goes all right. Thank you for responding to my question.
hi, I have problem while flashing.
Phone flash tool always gives ERROR
Automatic reboot is not supported on this device, please reboot the device manually
ERROR : [Port 0/1/4] Failed to reboot the device
Click to expand...
Click to collapse
Any idea what to do? I followed all the steps, tried many times, still same problem. And it's not possible to reboot device manually, because then it lose connection with PC
Restock OS Without Android
Hi there.
I have to restock my Device, but the Intel Flash Tool does not recognize my Device.
I cannot boot into Android to turn on USB-Debugging or go into fastboot mode
How do i flash my device without any OS installed?
---------- Post added at 04:03 PM ---------- Previous post was at 03:52 PM ----------
affe2000 said:
Hi there.
I have to restock my Device, but the Intel Flash Tool does not recognize my Device.
I cannot boot into Android to turn on USB-Debugging or go into fastboot mode
How do i flash my device without any OS installed?
Click to expand...
Click to collapse
Ok, got it working... dnx fastboot mode is there
....
hello guys by accident i deleted windows 10, how can i reinstall them? i dont have the windows 10 icon in the dual boot select i only see the android icon
mike mike baby said:
hello guys by accident i deleted windows 10, how can i reinstall them? i dont have the windows 10 icon in the dual boot select i only see the android icon
Click to expand...
Click to collapse
Straightforward if you can obtain a USB stick capable of storing over 7GB (some 8GB sticks may not); USB hub (ideally a powered hub); USB keyboard; OTG cable.
1) Obtain the Windows files of the correct firmware. The procedure outlined here is for E6E9 firmware, but other firmware will be similar. Download the circa 6.5GB E6E9 firmware Windows files from https://yadi.sk/d/XEvRsoiD3Q4vKX or https://mega.nz/#F!I0AXGR5C!YiNFkZL9DIvzepH28qAjEQ (or from appropriate source for your firmware version).
Decompress the downloads as required to obtain six folders and two files.
2) Format the stick to FAT32.
3) Name the stick WINPE (five uppercase characters).
4) Copy the previously mentioned folders and files to the USB stick.
5) Plug USB stick and USB keyboard into hub; plug hub into OTG cable; plug OTG cable into tablet whilst the tablet is off.
6) Turn on tablet and immediately start tapping << Delete >> key on USB keyboard. This should open the UEFI config section prior to Android boot option. If the tablet displays the Android boot option, turn off the tablet, wait a few seconds, then turn on and start tapping << Delete >> key on USB keyboard again.
7) When in UEFI, touch the title menu option of << Save and Exit >> and look in the << Boot Override >> section for the name of your USB stick, then touch the name of your USB stick. The screen will immediately go blank as the tablet starts to boot from the USB stick.
8) After a few minutes, a numerically display of progress will be displayed in a CMD window.
9) After reaching 100% and nearing completion of the overall installation, the tablet will prompt for acceptance, so accept that prompt.
10) The setup will run a few final operations for a few seconds, then automatically reboot.
11) Done.
You will be prompted to complete the OOBE on each Windows boot until you complete OOBE.
I am having trouble with this.
I have tried the universal installer which correctly identifies it as 64bit system. But it fails at download stage, I guess because the file is no longer available where the installer is expecting it.
So then I tried running "NovacomInstaller_x64.msi" by double clicking it, which installs novacomd in my add/remove programs so it seemed to work. But when I run "tptb_v42_win.bat" it says
Code:
Setting Palm path ...
Checking novacom service ...
Loading TPToolbox ...
unable to find device
.
Cannot connect to Touchpad.
Make sure Touchpad is connected with USB cable.
Make sure Touchpad is in webOS Recovery (bootie) mode
(where big USB symbol shows on Touchpad screen)
.
Press any key to continue . . .
The touchpad is definitely on the Web OS recovery screen and connected via USD so I assume it must be to do with drivers not installing properly. Any advice on how I can check drivers?
thanks,
James
jamesking420 said:
I am having trouble with this.
I have tried the universal installer which correctly identifies it as 64bit system. But it fails at download stage, I guess because the file is no longer available where the installer is expecting it.
So then I tried running "NovacomInstaller_x64.msi" by double clicking it, which installs novacomd in my add/remove programs so it seemed to work. But when I run "tptb_v42_win.bat" it says
Code:
Setting Palm path ...
Checking novacom service ...
Loading TPToolbox ...
unable to find device
.
Cannot connect to Touchpad.
Make sure Touchpad is connected with USB cable.
Make sure Touchpad is in webOS Recovery (bootie) mode
(where big USB symbol shows on Touchpad screen)
.
Press any key to continue . . .
The touchpad is definitely on the Web OS recovery screen and connected via USD so I assume it must be to do with drivers not installing properly. Any advice on how I can check drivers?
thanks,
James
Click to expand...
Click to collapse
You can following this thread ( I have you start at post 405 ) where another user called @smithylovestouchpad had the same issue with novacom not connecting to the server, and he was able to use a backup PC and it worked....
https://forum.xda-developers.com/showpost.php?p=80016590&postcount=405
But that being said, your in luck James, because a "regular user" by his own admission, @HP_TOUCHPAD will be posting very soon what he likes to call "HP_Touchpad_Novacom_Recovery_Android", and with this, any user can perform the following tasks with one click on any computer:
1) Load the ToolBox (flash the A6 Firmware)
2) Fix /boot using Create_Boot ( If the Bermuda Triangle shows up ) or the Tablet can not boot.
3) Automatic_Wipe_All_and_Create_Android_with_Swap ( Total Data Reset )
4) If the Tablet needs to be set up only for Android.
5) Change the Ramdisk, make all setting modifications and create a Custom boot file.
HP_TOUCHPAD once said,
If the user ever needs help, the tablet can be setup "completely" by another user, even remotely running Automatic_Wipe to Android, all they need is an internet connection.
The Novacom Driver and Android ADB Shell will be permanent and fully working all the time regardless of the PC being used.
DoubleStuff said:
You can following this thread ( I have you start at post 405 ) where another user called @smithylovestouchpad had the same issue with novacom not connecting to the server, and he was able to use a backup PC and it worked....
https://forum.xda-developers.com/showpost.php?p=80016590&postcount=405
But that being said, your in luck James, because a "regular user" by his own admission, @HP_TOUCHPAD will be posting very soon what he likes to call "HP_Touchpad_Novacom_Recovery_Android", and with this, any user can perform the following tasks with one click on any computer:
1) Load the ToolBox (flash the A6 Firmware)
2) Fix /boot using Create_Boot ( If the Bermuda Triangle shows up ) or the Tablet can not boot.
3) Automatic_Wipe_All_and_Create_Android_with_Swap ( Total Data Reset )
4) If the Tablet needs to be set up only for Android.
5) Change the Ramdisk, make all setting modifications and create a Custom boot file.
HP_TOUCHPAD once said,
If the user ever needs help, the tablet can be setup "completely" by another user, even remotely running Automatic_Wipe to Android, all they need is an internet connection.
The Novacom Driver and Android ADB Shell will be permanent and fully working all the time regardless of the PC being used.
Click to expand...
Click to collapse
Thank you for your help. In the end a combination of installing and reinstalling novacom, restarting, and then plugging in the touchpad to a different USB port finally sorted it out! Then I used your tool to get a ROM etc on there.
Do you have any particular recommendation for a smooth ROM? Doesn't have to be latest version of Android, just something that runs super snooth!
I've installed Dirty Unicrorn Pi but it's a bit laggy. It'll be fine to use fit it's intended purpose, but anything that improves on this would be appreciated.
Cheers,
James
jamesking420 said:
Thank you for your help. In the end a combination of installing and reinstalling novacom, restarting, and then plugging in the touchpad to a different USB port finally sorted it out! Then I used your tool to get a ROM etc on there.
Do you have any particular recommendation for a smooth ROM? Doesn't have to be latest version of Android, just something that runs super snooth!
I've installed Dirty Unicrorn Pi but it's a bit laggy. It'll be fine to use fit it's intended purpose, but anything that improves on this would be appreciated.
Cheers,
James
Click to expand...
Click to collapse
I am curious to what install process you have used to install the Dirty Unicorn Pie? Please respond, its nice to see what install processes some users are using....like what speed of Universal swap settings did you install?, did you use ROM reducer?
In the meantime since you have Novacom and TPTB installed try this process to install maybe Nougat, Oreo or Pie ( with /swap ) or KitKat or Lollipop. Once you read the OP it will direct you to the key Android versions to install on HP_TOUCHPAD's page.
I currently use KitKat and I am fine with that.
https://forum.xda-developers.com/hp...-guide-alternative-method-to-install-t3575861
Hi,
Thanks again for the advice.
I booted in to TPToolbox
Ran Complete Data Reset
Then rebooted to WebOS recovery.
Ran the ."TPTB_WipeAll_TWRP_v02_win.bat" which ended up with me in TWRP.
Then I installed ROM, reducer, gapps, optimiser, recovery, and super user via TWRP and it all raun when rebooted.
Now - another question - my second touchpad - It is currently sitting in the Touchpad toolbox screen. My PC has just broken (RAM corruption), I only have a Raspberry Pi which is not compatible with novacom drivers.
I've already ran "Complete Data Reset" but wasn't able to run the "TPTB_WipeAll_TWRP_v02_win.bat" before my windows PC got Blue Screen of Death!
So now I can copy zips to my touchpad and potentially install android, gapps, recovery using the tool. Then I figured I'd go in to recovery and flash "Automatic_Wipe_All_and_Create_Android_with_Swap_Partition" and start again.
The problem I have is I cannot flash android/recovery/gapps with TP Toolbox as I need a set of three compatible files.. Can anyone point me to a set of such files? Or another way of doing this from TP Toolbox - remember - I can't currently run anything on a PC!
This wouldn't be desperately urgent if it weren't for the fact that my mum wants to use these devices as digital photoframes on Thursday (my grandads funeral!).
Any help would be appreciated.
Currently I have
du_tenderloin-v13.0-20190328-1316-RC.zip
FLINTMAN-TWRP-touch-data_media-SELINUX-2.8.3.0-12-23-14.zip
I downloaded a zip from Open Gapps but TP Toolbox says its not compatible and will not flash.
jamesking420 said:
Hi,
Thanks again for the advice.
I booted in to TPToolbox
Ran Complete Data Reset
You don't have to do a Complete Data Reset anymore with the TPToolbox if your going to run TPTB_WireAll_TWRP_02_win.bat or flash Automatic_Wipe_All_and_Create_Android_with_Swap_Partition, it almost seems like your combining three different methods of installs, because TPTB_WipeAll_TWRP_v02_win.bat actually flashes Automatic_Wipe_All_and_Create_Android_with_Swap_Partition in the background and that actually does a complete data reset and creates a 500 Mb swap partition, and re-creates the system, cache, media and data partitions with sizes of 2200 Mb, 200 Mb, 500 Mb, and "rest of memory" respectively, also automatically installs version 3.2.1-0 of TWRP which is required for the other ZIPs.
Only use TPToolbox to flash A6 firmware, or look at partition sizes.
Then rebooted to WebOS recovery.
Ran the ."TPTB_WipeAll_TWRP_v02_win.bat" which ended up with me in TWRP.
Then I installed ROM, reducer, gapps, optimiser, recovery, and super user via TWRP and it all raun when rebooted.
Now - another question - my second touchpad - It is currently sitting in the Touchpad toolbox screen. My PC has just broken (RAM corruption), I only have a Raspberry Pi which is not compatible with novacom drivers.
I've already ran "Complete Data Reset" but wasn't able to run the "TPTB_WipeAll_TWRP_v02_win.bat" before my windows PC got Blue Screen of Death!
So now I can copy zips to my touchpad and potentially install android, gapps, recovery using the tool. Then I figured I'd go in to recovery and flash "Automatic_Wipe_All_and_Create_Android_with_Swap_Partition" and start again.
How are you copying zips to your touchpad if your PC does not work? Once you
flashed Automatic_Wipe_All_and_Create_Android_with_Swap_Partition it should get you to a
TWRP Recovery install screen, and you can then flash your zips, no need to use TPToolbox as I said before. Essentially TPToolbox is an "old school" method now. And flashing from TWRP Recovery you don't need compatible zips, that is a bug of TP Toolbox that has not been fixed.
The problem I have is I cannot flash android/recovery/gapps with TP Toolbox as I need a set of three compatible files.. Can anyone point me to a set of such files? Or another way of doing this from TP Toolbox - remember - I can't currently run anything on a PC!
I am curious, even if we point you to a set of such files, how are you going to copy them from a broken PC?, and see above for another way of doing this than from TPToolbox, if you can get into TWRP recovery and have zips on your Touchpad your all set.
This wouldn't be desperately urgent if it weren't for the fact that my mum wants to use these devices as digital photoframes on Thursday (my grandads funeral!).
Any help would be appreciated.
Currently I have
du_tenderloin-v13.0-20190328-1316-RC.zip
FLINTMAN-TWRP-touch-data_media-SELINUX-2.8.3.0-12-23-14.zip
I downloaded a zip from Open Gapps but TP Toolbox says its not compatible and will not flash.
Your PIE version above is the latest version, good. But the TWRP 2.8.3 version above is "old school" we are currently at this version FLINTMAN-TWRP-3.2.1-0-03-15-2018, and like I said above the "Wipe All" methods automatically install this latest TWRP version, so no need to flash an "old school" TWRP's afterwords.
Click to expand...
Click to collapse
I made comments above in blue. Here is my summary.
Because your PC broke, like you said "blue screen of death, RAM corruption". This is the very reason that @HP_TOUCHPAD is thinking "outside the box" trying to create an environment that users will not be dependent on a PC anymore. He is in the process of creating this environment, but lets give him time. For by his own admission he is just a regular user, he is learning, experimenting, creating and testing. He is also documenting his findings for all of us to read, learn and apply. So let us do our due diligence and do the best we can.
I have a raspberry pi computer I can use that I can copy files to/from with but I cannot install novacom drivers on it as they are not compatible, as far as I'm aware.
I think I might have found a suitable grouping of ROM/gapps/recovery I can flash with tptoolbox - literally trying again now
jamesking420 said:
I have a raspberry pi computer I can use that I can copy files to/from with but I cannot install novacom drivers on it as they are not compatible, as far as I'm aware.
I think I might have found a suitable grouping of ROM/gapps/recovery I can flash with tptoolbox - literally trying again now
Click to expand...
Click to collapse
This appears to be working to install a KK ROM so I will see if it comes up and I can then run the various flashes.
PS - yes - I did think that running Complete Data Reset and the "TPTB_WipeAll_TWRP_v02_win" was probably unecessary but I'd already run Complete Data Reset before I realised that it probably was overkill. Since this process worked I decided to do it again on the second touchpad, but the Windows PC died before I got the chance. But I had already run the process to load TPToolbox on to the tablet. So I'm now flashing TWRP v2.8.3.0 (data media), a KK ROM, and some KK compatible GApps using TPToolbox.
I hope that after that I can use the recovery I have loaded to install a new ROM, Rom Reducer, SU, Optimiser, GApps, and a more recent Recovery.
jamesking420 said:
snip...
My PC has just broken (RAM corruption), I only have a Raspberry Pi which is not compatible with novacom drivers.
...snip
Click to expand...
Click to collapse
I learn something new everyday, I just googled Raspberry Pi and its some sort of tiny, dual-display, desktop computer. At first I thought it was some sort of "Rogue ROM", I guess we can always learn something new everyday, like last month I learned to play Run Race 3d and I am not even a gamer.
And yesterday I wrote a program in a UNIX language called "AWK"
Yep it worked - so I then was in recovery on the device and I ran the Wipe all zip and then I flashed ROM, Optimiser, Reducer, Gapps, SU, recovery (again?!) and now it looks like it is loading in to Dirty Unicorn Pi.
I will have a play with it on the the max MHz optimiser kernel and then see if I want to stick with this or move on to an older/less system intensive ROM.
Thank you for your help!
jamesking420 said:
Yep it worked - so I then was in recovery on the device and I ran the Wipe all zip and then I flashed ROM, Optimiser, Reducer, Gapps, SU, recovery (again?!) and now it looks like it is loading in to Dirty Unicorn Pi.
I will have a play with it on the the max MHz optimiser kernel and then see if I want to stick with this or move on to an older/less system intensive ROM.
Thank you for your help!
Click to expand...
Click to collapse
As per your comment recovery ( again?! ), only flash recovery if you want a different version than what the Wipe all zip flashes ( currently flashes TWRP 3.2.1 ), lets say in the future nobody is updating the Wipe all zip, and it still flashes TWRP 3.2.1, but you see a newer version of TWRP 4.1 compatible with the touchpad, then you can flash that at the tail end, or if your fond of an older version like TWPR 2.8, same thing.
Thanks - yes - I want sure if Wipe all Zip was flashing or just into TWRP so I flashed it again just to be on the safe side. Because it was called wioe ask I thought maybe it wasn't actually flashing anything new, just wiping and booting.
Anyway, thanks for your help it was very useful.
jamesking420 said:
Yep it worked - so I then was in recovery on the device and I ran the Wipe all zip and then I flashed ROM, Optimiser, Reducer, Gapps, SU, recovery (again?!) and now it looks like it is loading in to Dirty Unicorn Pi.
I will have a play with it on the the max MHz optimiser kernel and then see if I want to stick with this or move on to an older/less system intensive ROM.
Thank you for your help!
Click to expand...
Click to collapse
The HP Touchpad Novacom Repair Android guide:
Click HERE for the Guide and File
A live Linux CD, just boot it from any PC, no installation is need it and have full control of the Tablet for ever !
Thanks for posting this, I'm sure it will be useful for many people.
Unfortunately on the way home from the funeral I left the two touchpads on top of the car as I was putting my kids in their car seats. They feel off at a roundabout which I imagine caused some damage. We turned around and went back for then and someone has nicked them! Ah well!
At 8 years old and costing less than £100 each they'd had a good innings.
Sent from my ONEPLUS A5000 using Tapatalk
jamesking420 said:
Thanks for posting this, I'm sure it will be useful for many people.
Unfortunately on the way home from the funeral I left the two touchpads on top of the car as I was putting my kids in their car seats. They feel off at a roundabout which I imagine caused some damage. We turned around and went back for then and someone has nicked them! Ah well!
At 8 years old and costing less than £100 each they'd had a good innings.
Sent from my ONEPLUS A5000 using Tapatalk
Click to expand...
Click to collapse
That is very unfortunate, but there is nothing to worry. The Tablets can be found for $10 anywhere and you maybe surprise to find in a dumpster somewhere.
But it can be revive to its full working conditions and all the files are posted on here, it only takes a click and is done!