There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
Hi there,
I've read through the stickies and searched for a solution to this problem. However, I am still unable to find a solution.
So, I my Galaxy S was rooted with One-Click Lag Fix and I decided to upgrade the firmware on it. I did not think that I needed to unroot it before I performed the update though. When the phone rebooted itself, it would show the Galaxy S start-up logo then go black. However, it does vibrate..at random intervals for some odd reason even if the screen is black.
tl;dr - Anyway, my Galaxy cannot go into recovery mode through the 3 buttons method and I can't seem to connect it to Kies or connect usb and whatnot. So, am I doomed to send it back for repairs? Or is there some way.
Thanks in advance!
materialism said:
Hi there,
I've read through the stickies and searched for a solution to this problem. However, I am still unable to find a solution.
So, I my Galaxy S was rooted with One-Click Lag Fix and I decided to upgrade the firmware on it. I did not think that I needed to unroot it before I performed the update though. When the phone rebooted itself, it would show the Galaxy S start-up logo then go black. However, it does vibrate..at random intervals for some odd reason even if the screen is black.
tl;dr - Anyway, my Galaxy cannot go into recovery mode through the 3 buttons method and I can't seem to connect it to Kies or connect usb and whatnot. So, am I doomed to send it back for repairs? Or is there some way.
Thanks in advance!
Click to expand...
Click to collapse
Since it did start to boot, you might try seeing if you can issue the command
adb reboot recovery
Hmm I thought I have to enable/disable some USB settings (USB Debugging) before ADB Reboot Recovery works.
Nonetheless, I'll give that a try and report back. Thanks.
EDIT: No luck =\
I've only way to actually fix it is going into the recover mode and doing a factory reset .
Volume Down button + Home key + Power
Volume up button + Home key + Power
one of them goes to recovery other goes to the android installing thing.
try them both not sure which is which.
Yes I know. However, my I9000 is unable to do the 3 button method (some sort of bug/defect).
Basically, I have to bring it back for repairs =.=
Hey i know the answers are here but the only net access i have is on my phone its really hard to find answers.
That being said i tried flashing my gfs stock 2.2 captivate with the fire fly rom via rom manager. Now it is stuck at the att logo screen. I tried doing 3button recovery but couldn't get in. I can get in downloading mode though. Can you give me stock tar file to flash thru Odin please or just the link also i made a nandroid backup with cmw but can't get into recovery. Thank you guys
dont know how your going to do it if you only have internet on your phone... but if you do at some point have access to a computor i would suggest the odin one click to revert to stock 2.1 but thats only if the phone came with 2.1 if it came with 2.2 i'm not exaactly sure what you would do but ive heard some horror stories of new bricked capivates because of using the one click.
so to recap if it came with 2.1 use this
http://forum.xda-developers.com/showthread.php?t=731989&highlight=stock
Thanks for the reply. I will have access to PC later that's why i want to gather info now. Anyway the phone actually came with the 2.2. Maybe there's a stock 2.2 tar somewhere to flash via Odin? Is there any other way i can try to get into recovery cause i made a backup. I tried holding volume up with home button and power button but it just keeps restarting. Also tried letting go of the power button while holding the two still.
ah... well thats your problem. volume, home and power is the i9000 captivate is both volumes and power and then release once you see the [email protected] logo. i see your on tmobile so im guessing your on the vibrant... ok so once you volume up down and power you should get into clockwork from there wipe dalvic factory reset and wipe cache should boot from there and if not just say and ill try to find the answer in the meantime
Thanks for your replies man i tried both volumes and power button followed by a release at att logo but nothing happens just sits there..
Anyone has a tar i can use to bring me to stock via Odin?i know there's got to be one.. i can get into download mode but can't get into recovery... bummer.
Sorry just read whit i typed and realized i said it wrong. you hold down all three buttons then release the power when you see the at&t logo but continue holding the volume rockeruntill it boots to clockwork
i just got to my pc. i tried that as well with no luck. any other suggestions?
Do the same procedure but let the boot screen process cycle through twice and then release the power button.
Sent from my SGH-I897 using XDA App
Samsung Captivate 2.1 soft brick please help
I have a samsung captivate was working fine until I forgot to charge it and the battery was completely drain. After full recharge turn on the phone but now stock on the Galaxy S logo then turn off. I can access recovery mode but still can't passed the galaxy S logo after recovery mode. My phone was rooted V2.1 EClair and lag fixed. Any help really appreciate it.
Phone can access via ADB command but i dont know the commands. Please help I stock on the Galaxy S logo after a while the screen turn black.
JIG is best solution. You should get one for up rom
MobileXT said:
I have a samsung captivate was working fine until I forgot to charge it and the battery was completely drain. After full recharge turn on the phone but now stock on the Galaxy S logo then turn off. I can access recovery mode but still can't passed the galaxy S logo after recovery mode. My phone was rooted V2.1 EClair and lag fixed. Any help really appreciate it.
Phone can access via ADB command but i dont know the commands. Please help I stock on the Galaxy S logo after a while the screen turn black.
Click to expand...
Click to collapse
If all of your apps/contacts are backed up i would suggest just reflashing stock JF6 eclair via OdinOneClick.
so yeah, I'm trying to flash CM7.2 to my friends Mini, but her phone has a broken Home button... so... I can't even get into download mode so I could use Odin to flash CWM to the device.
I got as far as getting it rooted, then I thought that I'd be able to flash CWM via RomManager, since I did that on my other friends Desire that had problems with some other button. But in RomManager when I choose to flash CWM it asks me to confirm my phone model, but doesn't show a option for the Mini? I checked on CWM's homepage and there they got a recovery for the mini so why isn't it in RomManager?
So anyone of you got any idea of how to flash CWM without that damn home button? Something as ADB or something?
Please help, this is so damn frustrating!
EDIT: SERIOUSLY NEED HELP ASAP! I thought that if I managed to get into the stock recovery I might be able to flash something from there, BUT APPARENTLY the stock recovery uses the Home button instead of the power button to choose an option, so now I'm stuck in stock recovery, can't choose anything, and when rebooting the phone boot back into the recovery! what the **** samsung? I can't get past recovery without a homebutton? not even pulling the battery helps!!! The phone is practically bricked now
Do not even think of using ROM Manager. It is responsible for many hard bricks for galaxy mini users.
Maybe you should get the home button fixed. :| Without that how you gonna multi task? Soft keys? Better fix it or sell the phone. Not worth keeping it without a working home button.
chemicalrage said:
Do not even think of using ROM Manager. It is responsible for many hard bricks for galaxy mini users.
Maybe you should get the home button fixed. :| Without that how you gonna multi task? Soft keys? Better fix it or sell the phone. Not worth keeping it without a working home button.
Click to expand...
Click to collapse
I know that the homebutton is rather important but it's not my phone, it's my friend's phone and she doesn't care if it works or not as she doesn't use the phone that much for multitasking.
oh by the way, I managed to get ONE successful home button press while in the recovery I placed a pen on top of the button and applied all of my super-human strength on that sucker phone rebooted normally, didn't get it into download mode though tried multiple times but no luck, just that one single press... might crack this phone open and see if I can fix that stupid button, or atleast see if I can short 2 contacts while the phone is open and get a home press that way
and I guess there isn't a way to flash anything on this thing without that pesky button
search on google for an application called CWM.apk it does work on our mini and it is a kind of rom manager
in command prompt type
adb reboot download and you will be in download mode