I converted back to ext3 with BackToEXT3 by Paul but didn't realize I needed to restore a new image right away. Instead I shut down the phone to use SmartFlash. Smartflash doesn't find the phone though and the phone doesn't boot anymore (ie. no logo, no recovery, no nothing).
If I try NVFLASH to restore the phone I get the following error message:
failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: failed to create the partition (code: 10) message: nverror:0x
42003 (0x42003) flags: 0
Full log below, appreciate any help I can get.
Code:
nvflash.exe --bct E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct --se
tbct --odmdata 0xC8000 --configfile android_fastboot_emmc_full.cfg --create --bl
fastboot.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: unknown
chip id: 0x20 major: 1 minor: 3
chip sku: 0xf
chip uid: 0x028841484340d557
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
sending file: E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct
- 4080/4080 bytes sent
E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct sent successfully
odm data: 0xc8000
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: fastboot.bin
/ 1024992/1024992 bytes sent
fastboot.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
[B]failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: failed to create the partition (code: 10) message: nverror:0x
42003 (0x42003) flags: 0 [/B]
My O2X is laying as dead weight on my bookshelf at the moment. I think today I must send it in for repairs before it (or me) gets suicidal. If anyone has any advice to offer on this problem I will send you gingerbread cookies.
You should ask Paul from MoDaCo. Either via Twitter or his forum.
Hi Team,
MY lg 2X is bricked as hell, doesnt respond to anything, no boot logo at all, doesn't seem NVflahable, when i follow PaulOBrien's guide i get a hang at waiting for bootloader to initialize.
Code:
C:\flash\2x\2x-v10b-1300166062-nvflash>.\nvflash.exe --bct E1108_Hynix_512MB_H8T
BR00U0MLR-0DM_300MHz_final_emmc_x8.bct --setbct --odmdata 0xC8000 --configfile a
ndroid_fastboot_emmc_full.cfg --create --bl fastboot.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: unknown
chip id: 0x20 major: 1 minor: 3
chip sku: 0xf
chip uid: 0x0280408540c07457
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
sending file: E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct
- 4080/4080 bytes sent
E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct sent successfully
odm data: 0xc8000
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: fastboot.bin
/ 1024992/1024992 bytes sent
fastboot.bin sent successfully
waiting for bootloader to initialize
This is as far as i get, is there a physical error on the phone or am i doing something wrong?
Any help would be greatly appreciated.
Try maliacrete thread dated 6/5/11 title big mess up after update. I tried it and it surprisingly work. Inatruction was in german tho..but np..google chrome can solvr the language issue. But beware..you'll end up with a brand new fone..
Newbie on the block.
Sadly the LG is not recognized by smartflash whatsoever.
Plugging the phone in while holding voldown yields no results, nothing on screen and nothing smartflash can see.
is the phone irreversibly bricked?
Have you change/swap the usb port as well like robbie said in the instruction? What i did was..i change the port, it still didnt recognise, the only thing pop up was lg logo..then i kind of give up and stop holding the vol key.
(Make sure u r on the 'ROM copy D/L' smartflash tab)
Now try the step again untill you see the lg logo (make sure batt off), then let go vol down key, then re-press the key..by now..the S/W loading pict should be seen n smartflash must be able to detect ur 2x n will fill the blank. Now press start on the smartflash, sit back n let the rest done by smartflash. Once complete, unplug, batt in, and restart as normal. A new born 2X should be ready to see what lies ahead of him/her..
Im still trying to recover all my setting, data n app manually. Btw..dont forget to bckup after cwm.
xxsacra said:
Sadly the LG is not recognized by smartflash whatsoever.
Plugging the phone in while holding voldown yields no results, nothing on screen and nothing smartflash can see.
is the phone irreversibly bricked?
Click to expand...
Click to collapse
Hade the same problemen. I just installed the drivers in my laptop and then it worked. I cant do a nvflash with my desktop but works like a charm on my laptop. Try another pc.
Sent from my LG-P990 using XDA App
Did you figure it out?
xxsacra said:
Hi Team,
MY lg 2X is bricked as hell, doesnt respond to anything, no boot logo at all, doesn't seem NVflahable, when i follow PaulOBrien's guide i get a hang at waiting for bootloader to initialize.
Code:
C:\flash\2x\2x-v10b-1300166062-nvflash>.\nvflash.exe --bct E1108_Hynix_512MB_H8T
BR00U0MLR-0DM_300MHz_final_emmc_x8.bct --setbct --odmdata 0xC8000 --configfile a
ndroid_fastboot_emmc_full.cfg --create --bl fastboot.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: unknown
chip id: 0x20 major: 1 minor: 3
chip sku: 0xf
chip uid: 0x0280408540c07457
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
sending file: E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct
- 4080/4080 bytes sent
E1108_Hynix_512MB_H8TBR00U0MLR-0DM_300MHz_final_emmc_x8.bct sent successfully
odm data: 0xc8000
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: fastboot.bin
/ 1024992/1024992 bytes sent
fastboot.bin sent successfully
waiting for bootloader to initialize
This is as far as i get, is there a physical error on the phone or am i doing something wrong?
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I have the same problem. Where you able to get it going?
I have the same problem too. I did what he suggested ... I tried on another pc and it worked! Thanks K.D.M.! :good:
It's the nvflash driver...need to be installed manually
Hi guys,
in moment of insanity I bricked my Tab using Odin. Now it's stuck in APX mode and I need help using nvflash. This is what I get:
D:\nvflash>nvflash --bl bootloader.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: unknown
chip id: 0x20 major: 1 minor: 4
chip sku: 0x4
chip uid: 0x0384018441400517
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
\ 1941020/1941020 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader failed NvError 0x0
command failure: bootloader download failed
Please note that in system information for chip name stands "unknown" instead "t20". I tried to drain battery, I even opened it and disconnected battery, with no result.
Thx for assistance
I have LG Optimus 2X P990 which was working normally till last two months.
In last two months it get slower and slower and now wont turn on and wont flash.
When I connect it to PC - PC recognize it and I can start flash process, but it always stuck
at the same step :
Nvflash started
rcm version 0X20001
System information:
chip name : unknown
chip id: 0x20 major:1 minor: 3
chip sku: 0xf
chip uid: 0x0280414640802297
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse : 17
sdram config strip: 0
sending file: 0-bct-settings.bct
- 4080/4080 bytes sent
0-bct-settings.bct sent successfully
odm data: 0xc8000
downloading bootloader -- load address: 0x10800 entry point: 0x108000
sending file: 0-fastboot.img
/ 1024992/1024992 bytes sent
0-fastboot.img sent successfully
waiting for bootloader to initialize
bootloader download successfully
setting device: 2 3
creating partition : BCT
failed executing command 16 NvError 0x120002
command failure: create failed <bad data>
bootloader status: failed to create partition <code:10> message: nverror:0x5 <0x1000005> flags:0
In this proccess, phone boot up with S/W upgrade... please wait text on it.
I have tried at 3 PC and 1 laptop PC - on Windows XP SP2/SP3 and Windows 7 32-bit
All drivers were installed and I dont know what to do to get phone boot and get to flash it..
Any ideas ?
Thx.
Dear People,
I have a problem with my LG P990. It keep hanging on the LG logo with a blue bar under it. I searched the symptons and I found out it is bricked.
This happend after i hard resetted my rooted phone. I tried the following things:
1. I have tried to use Smartflash but my PC wasn't able to recognize my phone when I plugged it in while holding the Volume Down button. I installed different drivers. The ones that were provided by a website and the drivers from the LG Support website.
2. I tried to use AIO toolkit but I get the following error I couldn't find any solutions for on the internet:
======================================
The phone will display a S/W download.. screen,
while the command-window will inform you of the progress.
Nvflash started
rcm version 0X20001
System Information:
chip name: unknown
chip id: 0x20 major: 1 minor: 4
chip sku: 0xf
chip uid: 0x0a7c818341ff2117
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: fastboot.bin
/ 1027184/1027184 bytes sent
fastboot.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
Succesfully updated partition table information to C:\Users\R...
\Temp\partitions.txt
Checking partition layout...Current Partition Layout could not be detected
Operation aborted
Press any key to return to main menu
I have Windows 8.1 but also tested these 2 methods on a Windows 7 PC.
I read about another method from one of the XDA members called ProgMaq but every download gives a 404 Not Found message or my browers warns me to not go to the website because it is not safe.
What can I do to unbrick my phone?
You should try to change bootloader and follow the instructions in aio
Change SD Card file system?