[Q] Phone can't boot, vibrates once, then twice - Captivate Q&A, Help & Troubleshooting

Hey guys, I need some help...
Long story short, I wanted to restart my phone one day after a Market app wasn't working, and when I turned it back on, it would load the ATT screen, show the Galaxy S screen as well, but then the screen turns black and about every 15-20 seconds, there would be 1 vibrate, a pause, 2 consecutive vibrates, and this would continue to go on forever until I took out the battery or the phone died. I had 2.2 but cannot get into recovery mode or download mode, even with the 3 button combo. Am I screwed?
Thanks for your guys's help!

kenwang2688 said:
Hey guys, I need some help...
Long story short, I wanted to restart my phone one day after a Market app wasn't working, and when I turned it back on, it would load the ATT screen, show the Galaxy S screen as well, but then the screen turns black and about every 15-20 seconds, there would be 1 vibrate, a pause, 2 consecutive vibrates, and this would continue to go on forever until I took out the battery or the phone died. I had 2.2 but cannot get into recovery mode or download mode, even with the 3 button combo. Am I screwed?
Thanks for your guys's help!
Click to expand...
Click to collapse
You probably need to build/buy a jig and use that to get to download mode. Otherwise, try this:
Take out battery
Plug in usb cable
Hold volume+ and volume-
Pop in battery
This should take you straight into download mode. You'll could try doing a factory reset while in download mode but you'll probably just have to flash a new ROM/Stock Image

Red_81 said:
You probably need to build/buy a jig and use that to get to download mode. Otherwise, try this:
Take out battery
Plug in usb cable
Hold volume+ and volume-
Pop in battery
This should take you straight into download mode. You'll could try doing a factory reset while in download mode but you'll probably just have to flash a new ROM/Stock Image
Click to expand...
Click to collapse
I agree with this technique, although in my experience, you should hold down both volume buttons BEFORE plugging in the usb cable to your phone. It should take you right to download mode, and from there, I'm sure you know your way around. Best of luck.

RooterBooter said:
I agree with this technique, although in my experience, you should hold down both volume buttons BEFORE plugging in the usb cable to your phone. It should take you right to download mode, and from there, I'm sure you know your way around. Best of luck.
Click to expand...
Click to collapse
Actually that particular order doesn't matter. It works both ways. All that matters is when the phone receives power (battery put it) it has the USB signal, the vol+ signal, and the vol- signal.

Related

[Q] No really, I bricked it...

OK, I've been reading here for 6 days all manner of Captivate unbricking. Here is my story...
I picked up a Captivate on the Rogers network. I connected it to my email server (Exchange 2010) with no problems, poked around, noticed the lag, noticed the SMS time issue, then promptly rooted, installed clockwork, and then threw cognition 2.2 beta 9.1.3. Quite frankly I was shocked at how much faster it was.
Anyways, after a day of poking around, I could not get my email to my exchange server running (tried the email.pak floating about), so I actually decided I was going to go back to the backup I made of my phone using clockwork before I installed cognition. When I restored my backup, I thought I had bricked my phone.
I let it rest for a day, then came back here, and found one of the 3-4 different variations of the 4 button download mode combo that permitted me to do the 1 click restore. This restored me to the AT&T version of 2.1. It worked, but was less than desirable.
I decided that at that point I really wanted to go back to stock, so I downloaded the stock backup on the Rogers Captivate wiki page, and did the restore using clockwork. The phone has not been the same since.
When i turn it on, I get an at&t splash screen, then in about 20 seconds I get the at&t "jingle", but the splash screen stays on. I can't seem to find any key combination that will permit me to get back into download mode so I can restore using the One Click that worked for me the first time. I have tried:
1. 3 button salute with USB in first, battery out initially.
2. 3 button salute with USB plugged in *as* I was inserting the battery.
3. Power and volume down (both with and without USB, and with battery being plugged in after USB and "during" insertion of battery)
4.Power and volume up with same combo's as #3.
5. Just volume up and volume down with same combo's as #3.
In all cases Odin was running before USB connected, running as administrator. I'm running 64bit windows, but I'm sure I have the correct drivers because I did this the first time with Odin and download mode and I haven't added or changed anything. But just for arguements sake I did uninstall, and then install the drivers again.
Any combination of power and volume buttons just gives me a battery charging logo. Occasionally when holding up until the second black screen I will get a quick indication that the computer might see something, but it dissappears withing a handful of seconds showing it promptly removed.
I'm downloading the Android SDK in the hopes that when I get the normal at&t splash screen after the "jingle" that something might actually be running in the background and maybe I can adb reboot download it but I'm not holding my breath.
Anyone seen this that has managed to get out of it? I'm starting to think the "unbrickable captivate" can be bricked. Assuming it is bricked, short of taking it back, is there anyone on the internet that can jtag these and in some fashion bring back to life?
Cheers,
Tim
This doesn't belong in Development.
MikeyMike01 said:
This doesn't belong in Development.
Click to expand...
Click to collapse
ditto
and download mode is easy.
1. start odin3 and have data cable plugged into the computer
2. insert proper files if needed
3. hold volume up and volume down for 2 sec (no power button needed) then insert usb cable, continue to hold volumes till either the download mode screen pops up or odin3 sees the phone(if you bork the phone bad enough you can corrupt the download mode image, i did it with the not to successfull manhatten project kernel) but despite the screen being black it very well may be in download mode.
4. start flash
5. if it doesn't work send it to me ill find a use for it
alternatively if the phone can go passed the splash screens and boots fully you can adb reboot download. just get the development kit and drivers on your pc.
Dani897 said:
ditto
and download mode is easy.
1. start odin3 and have data cable plugged into the computer
2. insert proper files if needed
3. hold volume up and volume down for 2 sec (no power button needed) then insert usb cable, continue to hold volumes till either the download mode screen pops up or odin3 sees the phone(if you bork the phone bad enough you can corrupt the download mode image, i did it with the not to successfull manhatten project kernel) but despite the screen being black it very well may be in download mode.
4. start flash
5. if it doesn't work send it to me ill find a use for it
alternatively if the phone can go passed the splash screens and boots fully you can adb reboot download. just get the development kit and drivers on your pc.
Click to expand...
Click to collapse
Thanks, but that doesn't work. All I get is the battery charging screen. Using the process it does not go into download mode.
MikeyMike01 said:
This doesn't belong in Development.
Click to expand...
Click to collapse
Could a moderator move this to Captivate General then? Sorry about that...
timmy22 said:
Thanks, but that doesn't work. All I get is the battery charging screen. Using the process it does not go into download mode.
Click to expand...
Click to collapse
just to be clear, you are holding volume up as well as volume down starting with the phone being powered down and continue to hold them after you plug in usb untill something shows on the screen?
if your phone is not seeing the volumes buttons you are one of the very unlucky few that had a problem at the most inopportune moment.
there is also a way where you hold all three buttons till the phone reboots twice, or something. let me try it and ill give more specifics.
timmy22 said:
Thanks, but that doesn't work. All I get is the battery charging screen. Using the process it does not go into download mode.
Click to expand...
Click to collapse
Pull the battery, open odin, plug usb into computer, hold vol up and down, plug usb into phone still holding vol buttons, drop in battery still holding vol buttons, when dl screen pops up and yellow com port lights up in odin release volume buttons. Do not touch power button at any time
Swyped...and sorry I don't proofread
Have you tried rebooting into recovery mode instead of download mode? Stock recovery is adb-ready and you should be able to adb reboot download. Its a long shot if you're having problems using button combo to get to d/l mode, but it's probably still worth a shot at this point.
If you were able to use 3 button combos before all this happened, and did NOT have to install the 3 button combo fix, its strange you don't have access to it now... Could restoring a Rogers Cappy to AT&T stock be the problem?
Dani897 said:
just to be clear, you are holding volume up as well as volume down starting with the phone being powered down and continue to hold them untill something shows on the screen?
if your phone is not seeing the volumes buttons you are one of the very unlucky few that had a problem at the most inopportune moment.
there is also a way where you hold all three buttons till the phone reboots twice, or something. let me try it and ill give more specifics.
Click to expand...
Click to collapse
Yes, that's exactly correct. I do this:
1. everything pulled (battery, USB, sim, sd)
2. Open Oden (1 click)
3. Install battery
4. hold down (and keep holding) volume up and volume down
5. insert USB cable
6. depress (i.e. don't hold) power button
Goes straight to battery charging indicator.
If I swap #6 with holding the power button down, it continually reboots while just barely showing the battery charging indicator. I've tried letting go between black screens on the 1st, 2nd, 3rd, 4th, and 5th black screen. Still no android dude with the shovel.
Try all the steps you stated but not the last one where you press the power button. Don't press the power button.
newter55 said:
Pull the battery, open odin, plug usb into computer, hold vol up and down, plug usb into phone still holding vol buttons, drop in battery still holding vol buttons, when dl screen pops up and yellow com port lights up in odin release volume buttons. Do not touch power button at any time
Swyped...and sorry I don't proofread
Click to expand...
Click to collapse
Goes straight to battery charging.
johnny13oi said:
Try all the steps you stated but not the last one where you press the power button. Don't press the power button.
Click to expand...
Click to collapse
Goes straight to battery charging.
Pull out battery for 10 seconds, hold volume up + down, connect usb into other usb port.
Sent from my GT-I9000 using XDA App
Seriously, try adb. It works wonders.
Sent from my SAMSUNG-SGH-I897 using XDA App
10tonhammr said:
Have you tried rebooting into recovery mode instead of download mode? Stock recovery is adb-ready and you should be able to adb reboot download. Its a long shot if you're having problems using button combo to get to d/l mode, but it's probably still worth a shot at this point.
If you were able to use 3 button combos before all this happened, and did NOT have to install the 3 button combo fix, its strange you don't have access to it now... Could restoring a Rogers Cappy to AT&T stock be the problem?
Click to expand...
Click to collapse
Trying to get into recovery mode gets me the at&t logo and the "jingle", but no recovery mode menu to reboot, etc.
This is what I'm worried about, restoring the Rogers stock over top of the Odin 1 click restore (which is an AT&T image) has bricked it and prevents download mode from invoking.
fatttire said:
Seriously, try adb. It works wonders.
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
I know, I played with adb before I bricked it. ADB needs to "see" the phone, it no longer sees it (I have three computers, all three can't see it, but they can see my friends cappy with no problems first time, every time). Same process for his phone works every time to get into download mode, but not on mine.
And yes, have tried other USB ports on the same computer, both on the mainboard, and on the front ports.
Keep the ideas coming though please, I will try every one.
timmy22 said:
I know, I played with adb before I bricked it. ADB needs to "see" the phone, it no longer sees it (I have three computers, all three can't see it, but they can see my friends cappy with no problems first time, every time). Same process for his phone works every time to get into download mode, but not on mine.
And yes, have tried other USB ports on the same computer, both on the mainboard, and on the front ports.
Keep the ideas coming though please, I will try every one.
Click to expand...
Click to collapse
There's a trick to prompt download mode through a "jig" which you can hack together for about $2 in parts and a sacrificial microUSB cable...it works on the other SGSes, but I think it should work on the Captivate as well. Never tried it personally...
Merlin_reloaded said:
There's a trick to prompt download mode through a "jig" which you can hack together for about $2 in parts and a sacrificial microUSB cable...it works on the other SGSes, but I think it should work on the Captivate as well. Never tried it personally...
Click to expand...
Click to collapse
I work in a tech shop so have access to electronics, sacrificial cables, soldering irons, resistors, caps, etc.... could you point me in the right direction?
Oh, nevermind, found it in the i9000 forum. Will test first thing in the morning!
Cheers,
I bricked one today as well. Exactly what you are talking about here. The only thing is that i was still under the 30days so i swapped it out for a new one. As of right now ive been debating whether i want to do the voodoo fix (which i think is what bricked it to begin with)

[Q] Phone Bricked?

Ok, so I had my Captivate flashed back to stock and had it rooted. I decided to update from JF6 to JH7 through Kies Mini. After it finished updating, my phone was stuck at the Samsung Galaxy S screen and then it turned black, but the buttons still light up.
I already tried doing the 3 button recovery/download mode in every way possible, but my phone won't seem to go into recovery mode or download mode no matter what I do.
When I leave the usb cable plugged into the phone as I turn it on, my computer plays the notification sound where a device has been connected, but still black screen on the phone. Happens when the AT&T screen loads, wonder if that would help somehow
Please help!
Raeon said:
When I leave the usb cable plugged into the phone as I turn it on, my computer plays the notification sound where a device has been connected
Click to expand...
Click to collapse
If you had usb debugging enabled you can send a "adb reboot download" or "adb reboot recovery" command to reboot the phone. If not then you probably have to make one of those usb jig's with the 301k resistor.
But you should still be able to enter download mode if you pull the battery, press the vol up/down and put the battery back. My stock phone couldn't enter recovery but it could get into download mode, keep trying.
Hmmmm. Still doesn't work when I pull out the battery, plug in the usb cable, hold the volume + and - down, and put the battery back on. It just shows the battery charging.
i have something similiar just have battery showing and wheel spinning when connected to pc or AT&T logo flashing if powered on and can't get into download mode...How does one get back to reality at this point.
your phone does not have the button combinations required to enter either download or recovery mode. I guess what you should have done before doing anything to your phone was test the button combinations in case something screwed up. then you should have flashed stock with the odin package posted in the development forum with the 3 button fix. I had to do this for my friend's captivated after realizing the button fix was disabled, but I hadn't broken the booting of the phone then. but now to fix it, other than trying to use adb to reboot into download, I have no idea what to do.
Looks like you'll need to make a JIG. Here's one thread on it:
http://forum.xda-developers.com/showthread.php?t=841512
norcal einstein said:
Looks like you'll need to make a JIG. Here's one thread on it:
http://forum.xda-developers.com/showthread.php?t=841512
Click to expand...
Click to collapse
Made a jig with parts bought from Radio Shack.
the jig was a success to get the phone back to download mode

[Q] Stuck on stupid:can't force download

Hate to be that guy, but alas I am
I flashed my Captivate with the latest Twingerbread ROM. Everything was running nice and smooth until I decided to use a Galaxy S Mod tool from the market place to change my battery icon.
Long story short the phone is now stuck trying to boot. It will run the Twingerbread loading animation for a few seconds, flash a screen that says
Candidates:
Preparing external SD Card
and then continue with the loading animation.
Before this happened I had been able to force download mode using only the volume up/down buttons, that is no longer the case. I have tried using adb to access and force download but the phone isn't found whether powered off or in it's current "loading" state. ODIN is able to recognize it as a COM:7 device but fails to flash it.
I'm in a bit over my head here, anyone have any suggestions on how to fix this?
Try this:
Open Odin and plug the cable into your computer only not your phone
Remove your battery from your phone
Wait 30 seconds and put it back in, don't turn your phone on
Hold both volume buttons down and then plug the cable into your phone, it should go into download mode.
jhernand1102 said:
Try this:
Open Odin and plug the cable into your computer only not your phone
Remove your battery from your phone
Wait 30 seconds and put it back in, don't turn your phone on
Hold both volume buttons down and then plug the cable into your phone, it should go into download mode.
Click to expand...
Click to collapse
Thank you for the suggestion but I can't get that to work for me. I tried it multiple times but it simply loads the charging screen. I have heard the term jig thrown around a time or two in here but can't seem to find any more info on it. Would that be my next step?
Yes if that doesn't work then you will need to get a jig to force download mode. Look here....http://www.mobiletechvideos.com/blog/?page_id=100
Good Luck
Nice, I don't have to make it even. Thanks for helping the noob out, jhernand1102. Hopefully this cures my issue.

Power button is broken? How to reboot to download?

Power everything was working this morning
Noticed that my power button wasn't working...the screen stayed on. Pulled battery, put it back in and the phone booted without pressing power.
Was like "wtf?"
When it booted, I couldn't turn off the screen.
So I just left the battery out and took it home.
Put a new rom on phone, thought "This will fix it."
Wrong.
Had to flash using Rom Manager because in recovery the power button doesn't respond.
When it began to boot "AT&T Screen" wouldn't disappear and show me some Doc's v4.
I can manipulate it to boot into recovery but the power button doesn't work still.
I can NOT get it to go into recovery.
Can someone helps me?
bunnsguy said:
Power everything was working this morning
Noticed that my power button wasn't working...the screen stayed on. Pulled battery, put it back in and the phone booted without pressing power.
Was like "wtf?"
When it booted, I couldn't turn off the screen.
So I just left the battery out and took it home.
Put a new rom on phone, thought "This will fix it."
Wrong.
Had to flash using Rom Manager because in recovery the power button doesn't respond.
When it began to boot "AT&T Screen" wouldn't disappear and show me some Doc's v4.
I can manipulate it to boot into recovery but the power button doesn't work still.
I can NOT get it to go into recovery.
Can someone helps me?
Click to expand...
Click to collapse
have ODIN open, and battery removed from phone... hook up usb, hold both vol keys, while inserting battery... you should get download mode fine even with a busted power button... what you do next is up to u....
Once more, I can NOT get it to boot into recovery in that fashion.
I cannot place batter in the phone without it attempting to boot
(doesn't not get past the AT&T boot screen)
I cannot plug it up, hold volume buttons and then put in battery because it will just charge. If I unplug the phone, the phone still thinks it's charging actually.
My question really is Can I 'fix' the power button, or can I reboot it into download mode through command propt? I've never used ADB to access my phone, so that'll be new.
bunnsguy said:
Once more, I can NOT get it to boot into recovery in that fashion.
I cannot place batter in the phone without it attempting to boot
(doesn't not get past the AT&T boot screen)
I cannot plug it up, hold volume buttons and then put in battery because it will just charge. If I unplug the phone, the phone still thinks it's charging actually.
My question really is Can I 'fix' the power button, or can I reboot it into download mode through command propt? I've never used ADB to access my phone, so that'll be new.
Click to expand...
Click to collapse
Dude... recovery is useless right now, you have a busted power button... and because of 'said busted power button', none of what you're trying to do is going to work... like youve said...
You are down to trying to force download mode with USB cord, holding the vol keys, and inserting the battery... ADB cannot run commands to a phone stuck at the boot screen... Thread title says, how to reboot to download, and with the button like it is, all you can do is what i've posted...
As to fixing the power button, i don't see why that's not possible... do u feel it press at all?
B-Naughty said:
As to fixing the power button, i don't see why that's not possible... do u feel it press at all?
Click to expand...
Click to collapse
Yeah, it 'presses' and 'clicks'. I mean it worked most of the day, it got low on power and it just quit working.
Any luck forcing download by puttin the battery in while the usb is hooked up with the vol keys pressed in?
I was having the same problem with my power button and eventually the power button stopped working completely even though i could still hear it click. I sent it to mobiletechvideos and they fixed it really fast and it was a great price.
Here's the link: http://mobiletechvideos.mybigcommerce.com/samsung-captivate-power-button-repair/
B-Naughty said:
Any luck forcing download by puttin the battery in while the usb is hooked up with the vol keys pressed in?
Click to expand...
Click to collapse
goes into boot-loop like if I were holding the volume up/down and the power together. That's what doesn't make sense.
j.curtis.369 said:
I was having the same problem with my power button and eventually the power button stopped working completely even though i could still hear it click. I sent it to mobiletechvideos and they fixed it really fast and it was a great price.
Here's the link: http://mobiletechvideos.mybigcommerce.com/samsung-captivate-power-button-repair/
Click to expand...
Click to collapse
And I could buy another used Captivate for $50. I have an upgrade in less than 3 weeks and this happens
It happened to me once before after flashing a bad kernel. I just did what B-Naughty had suggested. Remove battery -> plug in USB -> hold both volume buttons --> then insert battery. Put me right in download mode and Odin it back with a working power button. Unless it's really a hardware problem, then you're out of luck...
bunnsguy said:
And I could buy another used Captivate for $50. I have an upgrade in less than 3 weeks and this happens
Click to expand...
Click to collapse
Oh in that case imo i would get another used captivate and wait for the sgs 3
Maybe if I went to a store and sucked up to them they'd let me upgrade a month early (especially since I was initially supposed to upgrade in October)
Might be down to getting/making a USB jig if it don't come up... but if you upgrade to gs2, the jig will work for that model as well so won't be wasted...
B-Naughty said:
Might be down to getting/making a USB jig if it don't come up... but if you upgrade to gs2, the jig will work for that model as well so won't be wasted...
Click to expand...
Click to collapse
Maybe a jig would work. But easier, funner solution is adding a line for a Moto Atrix 1 for just a penny plus the $36 fee. Problem solved. Thanks for the help for what could just be a hardware failure. I'll upgrade my other line later when the SGS 3 comes out

Possible brick after updating twrp

Dear all,
I was on beyond 5.3 with twrp 3.3.1.7 and I wanted to update everything. Magisk, root etc was working fine.
I downloaded the patched twrp file from the beyond telegram chat and flashed it as image into the recovery partition.
The installation was finished in 2 seconds, but stupid me chose to power off instead of rebooting the recovery.
So I tried to enter recovery using the button combo but nothing happened and I was stuck with the samsung logo.
The current status is that my phone only shows the samsung logo.
Holding the power button for a minute doesn't do anything.
Pressing the button combo for recovery mode doesn't do anything.
Pressing the button combo for dl mode makes the phone reboot. It vibrates for a sec, then the samsung logo shows again.
If I keep pressing all 3 buttons the phone keeps on rebooting and vibrating each time, but dl mode never appears. If I let go of the power button the logo stays and again, nothing happens.
So basically I can't enter dl mode nor reboot.
Should I let it run dry and try again or just throw out of the window immediately? :crying:
I let the battery drain over night. Phone was finally off.
So when I plug it in, the Samsung Logo appears and doesn't change. It just stays like that forever until the battery drains.
Pressing the power button doesn't do anything, no matter how long. It doesn't reboot nor does the logo disappear.
Pressing vol+, bixby and power again does nothing.
Vol-, bixby and power makes the phone reboot. The screen turns black, the phone vibrates shortly, the logo reappears. If I keep pressing the buttons the phone reboots again, and again, and again, mever reaching download mode.
If I let go of the power button and keep pressing vol- and bixby the phone stays black and won't even show the logo. Nothing happens. If I let go of either of the two buttons the logo appears again.
It won't boot, won't go into recovery or go into dl mode.
I'm doing all this while it's plugged into the usb port of my pc, and it doesn't get recognized. Samsung 300k tool doesn't recognize it either.
Now I know the meaning of "bricked" lmao.
Does anyone know how to possibly fix this?
Pressing only the power button for a minute literally does nothing. Like hell, how is that even possible?
You can try this to go to download mode:
Vol down + bixby + usb cable connect to PC
It's advisable to charge battery first before flashing firmware.
XTrail02 said:
You can try this to go to download mode:
Vol down + bixby + usb cable connect to PC
It's advisable to charge battery first before flashing firmware.
Click to expand...
Click to collapse
I tried that for like a thousand times already but now it chose to magically work somehow.
I think I peed myself a little when that ugly turquoise screen appeared and I screamed from sheer happyness.
THANK you!!!
The problem that doesn't stop giving lmao.
Got into DL mode, got odin to start, but after like 10 seconds my phone dies and odin fails.
Now I cant get into DL mode, but rather only the "an error occurred while updating the device software. use the emergency recovery function in the smart switch pc software."
Could it be the battery that simply dies?
hoeni said:
The problem that doesn't stop giving lmao.
Got into DL mode, got odin to start, but after like 10 seconds my phone dies and odin fails.
Now I cant get into DL mode, but rather only the "an error occurred while updating the device software. use the emergency recovery function in the smart switch pc software."
Could it be the battery that simply dies?
Click to expand...
Click to collapse
Yes most probably a discharged battery. Hopefully you can go to DL mode again after charging your phone.
hello,
I've and S10e and because an important app to me I need to go back to android 9 where it works.
I've read a lot info about downgrade, but no one says ROOT/UNBRICK.
Can someone inform if there is a way of downgrade without ROOT (maintaining the warranty).
thanks in advance
P.S.: Maybe too naive question, sorry for that

Categories

Resources