[Q] Stuck in a boot loop - now just stuck - Galaxy S I9000 Q&A, Help & Troubleshooting

Hi has uploaded ICS 3333, and it worked for a few weeks then today when it in airplane mode I took it out my pocket and it was in a bootloop mode.
Samsung --> Semaphore
So decided that I would retry installing ICS starting with 2.3.6 using ODIN but it crapped out, and now it's only allowing me to go into download mode. It said failed, retried a few times but I did not record the exact error (aaah)
As it is allowing me to get to download mode thought that would be ok, but when I connect it to the PC, it is not recognised at all now. So ODIN does not seem to work..
Im sure you are going to say just install a specific driver or something, but I don't what it would be. The PC recognised the mobile earlier, but just not now.
Update: Now the Phone is fully dead, and does not appear to be charging at all. So maybe dead because the battery is flat.
I've updated ROm's a few time's and always had the recovery mode to recover things and even have the USB item which should allow to move into download.
Any idea's folks.
thanks in advance... Bill
I was following this initially
1st Install this - this flashes Andoid 2.3.6 first
I downloaded I900XXJVU_I9000OXAJVU_OXA.rar
Disconnect your phone if it’s connected to PC. Then Switch it Off. Wait 5-6 seconds for vibration to confirm complete switch off.
Now, put the Galaxy S in “Download Mode” — press and hold these keys together: Volume_DOWN+Home+Power until a screen saying ‘Download Mode’ comes up.
Open Odin (from step 5) — Odin3 v1.7.exe.
Connect your phone to PC now. You should get the message “Added! !” under the Odin’s message box in the bottom left. If you don’t get “Added! !” message, than probably there is a problem with drivers. Make sure you’ve drivers installed (links given above under heading ‘Pre-Installation thoughts’).
Now, in Odin, select these files at respective tabs (for visual help, see the screenshot at step 11 below):
a) Click the PDA Tab, and select CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 (from step 3.1)
b) Click the Phone Tab, and select MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 (from step 3.3)
c) Click the CSC Tab, and select GT-I9000-CSC-MULTI-OXAJVU.tar.md5 (from step 3.2)
d) Click the PIT Tab, and select s1_odin_20100512.pit (from step 2)
Make sure the ‘Re-Partition’checkbox in ODIN is selected. Also, Auto Reboot and F.Reset Time checkboxes should be selected too. Leave everything else on Odin untouched.
Double check everything said in step 10 and 11 above. Your Odin’s screen, after selecting all the files and ticking and not-ticking the checkboxes, should look like this:
Screen capture can be found at weblink
Now, hit the START button to begin the flashing process. When it finishes, your phone will automatically reboot, upon which you can unplug the cable. Plus, you’ll get a PASS (with green background) message in the left-most box at the very top of the Odin. ***I got a fail here***

read that kies is different from usb drives. Not 100% sure that would be the issue as could connect previously with ODIN, which I think means the drivers are ok.
Next question that I have, if the battery has gone flat, and it does not appear to be charging either with USB or wall mounted, where do I go from here...
Im not a total newbie, and have been on DarkyRom for most of the versions, just this boot loop has got me big style... Can anyone give me a few idea's of what to try...

You might try a direct battery charger for which you won't need your battery to be in phone and one charged you can try the usual things as flashing through odin.

Try to install another driver..since i use ics for my sgs..pc wont recognise my phone..i install s2 or nexus driver ( mtb driver ) and it works perfectly as before..

If you have flashed ICS then you will need to install the GNexus drivers that are contained here
Try and get your hands on a external charger as erpurohit has suggested or borrow a friends battery
Flashing back to stock or Darky's 10.2 should get your phone going again

Thanks folks for responses (did the button as well).
Did not need extra charger / battery. Sat it on charger all night with no change... So tonight when I came in tried one more time to put into download mode and it worked..
Tried connecting it to ODIN and it worked fully so installed Gingerbread stock and away the baby went.
Not sure root cause, but was not drivers.
Won't be installing ICS until it becomes more stable and does not put phones into boot mode without a simple way out.. (never say never though)
Cheers Anyway..

Related

[Q] Odin stuck at file analysis, what to do?

Hey all,
I've had enough with this stock JI6 froyo, the lag has taken the best of me unfortunately, so i am trying to go back to JF6 so i can the go to cognition.
However, my odin (one click) doesn't seem to want to get past the File Analysis- it did once but got stuck on PIT.
I've Tried
1)Rebooting the computer
2) running odin as admin
3) Running odin in xp sp3 mode
4) steps 2 & 3 together
5) Took out sim card and sd card
6) tried different USB ports
I must have tried at least 15 times now to get this to work. Each try i do.
1) Make sure nothing is plugged in
2) then i plugg in just the usb cable (no phone attached)
3) open odin
4) put battery back in phone, plug into usb and hold vol up/down
5) i enter download mode and odin sees the phone
6) click start- stuck on file analysis
*EDIT* I can now always get it to say Set PIT file, yet it won't go past that.
*EDIT2* So i finally got it to go through, what i did was just constantly try it on one port (probably 20 times on a single usb port) Then, one time when it was stuck at set pit file, i unplugged the phone so the odin said failed (or reset i don't remember), then i closed odin, unplugged the usb from the computer and moved it to another port, then tried it again and it worked.
*EDIT3* Well damn, i guess i posted a little too soon. It's now stuck on Factoryfs.rfs, and the load bar on the phone itself has not moved at all
Sorry for the question =(
*EDIT4*So repeating edit 2, 3 times now, its gotten back to factoryfs.RFS again. This time the load bar on the android moved to about half way, yet it stopped again.
*EDIT5* After repeating step 4 a few times the progress bar got farther and farther teach time. And finally odin says reset (in blue) and the phone is booting up =)
Thanks for any help you can give =)
I think you need to get a new cable, use a different computer, reinstall drivers, heck anything, you seem extremely unlucky.
how helpful.
same problem here.
IIRC, I was stuck at file analysis my first time. I then selected the repartition option in ODIN and it just flew through the process. I'm guessing the lagfix was getting in the way. Telling ODIN to basically reformat and not try to save the existing structure was the right thing to do.
What I do is power off, wait for battery to come on( plugged in) and turn on with holding volume buttons to get to download mode. Its the only way mine will complete the process
ANDROMEDA 2.0,1.2ghz and some kernel i can think of. (this is probably all wrong because i will change it in 45 minutes or so)

[Q] Bricked Verizon Tab

Hi,
I bought my Tab in the States a few weeks back and brought it home to Switzerland. I downloaded Lag Fix from the market and it put my tab to sleep. I was able to get into Flash mode and via Odin tried to flash P1000XXJK5 with a Euro PIT, it went through 95% and then failed and stalled. I tried to turn it off, then it went dead and all I can get now is a blank screen with indirect back light. No OS, little guy with a shovel, nuttin!
I also tried installing Android Commander, but it can't see it either
Can anyone help?
Well in order to fully brick a device, you need to corrupt the updating proccess while flashing the bootloader, otherwise its most of the times fixable by the user.
So if at that point you where updating the bootloader and it stopped then you are screwed.
If not, i would let its battery to fully die from leaving it on for some hours, and then charge it for an hour, if you are still getting a indication like that then you are screwed.
If you are at least able to get the Phone --!-- Computer sign, you are good to go. Let me know how did that go.
Hi,
Well, I did all that...still have just the white screen......no icons, no indications of anything.
Thanks for the help....
I have the same thing now... Have you come any closer to a solution?
damnyank said:
Hi,
Well, I did all that...still have just the white screen......no icons, no indications of anything.
Thanks for the help....
Click to expand...
Click to collapse
Euro ROM on a Verizon CMDA device?!?
cafcwest said:
Euro ROM on a Verizon CMDA device?!?
Click to expand...
Click to collapse
Euro (GSM) on a CDMA device? If that is right then you have trouble.
Are there JTAGs for the GTcdma?
does anyone have a solution on how to unbrick vz tab?!?
here's what you should do. let's start from the very beginning.
1. download heimdall. get it here: http://forum.xda-developers.com/showthread.php?t=755265
2. download the stock verizon files. get them here: http://www.blackmugmedia.com/Android...n/VZW Stock/
you need all four files.
3. download the drivers for the samsung sch-i800. find those here: http://downloadcenter.samsung.com/co...v1.3.350.0.exe
4. unzip heimdall. go into the drivers folder, and run zadig.exe. at the top, select 'list all devices'. go to the dropdown menu, and select Samsung Composite USB (i'm pretty sure that's what it was called.) click start, and let it run.
5. open the heimdall front end.
6. put system in system (if you're flashing to ec02, then put factory in system)
put cache into cache
put param into param
put the zimage into both the kernel and recovery slots.
7. turn your tab off, and plug it into the computer using USB. hold down the power and the volume down buttons until you see the little droid dude with a shovel.
8. click the start button on heimdall.
9. wait for the flash to complete (don't unplug your device, obviously, during the flashing.) once your phone reboots, it's okay to unplug it.
10. now, boot into the stock recovery, and wipe data and cache. update to ec02
11. enable usb debugging.
12. plug your phone back in to the computer.
13. now run superoneclick for root. get that here: http://forum.xda-developers.com/showthread.php?t=803682
14. either play with it in stock, or go find oldmacnut's excellent Better Than Life Rom, and follow the instructions to flash that.
15. enjoy your tab!
My friend had just given me his SAMSUNG GALAXY TAB SCH-I800 ... When plugged into the wall it shows a PHONE /!\ COMPUTER symbol and that is it! ...when I plug it into the computer that screen goes away, and doesn't come back . The computer doesn't recognize it or even acknowledge it when it is plugged into it. AGAIN...the phone /!\ pc screen only comes on when it is plugged into the wall...no other time. I cannot even get it into anything esle by doing the - power button/volume button commands.
Please help a cracka out!

[Q] How to remove CM7 and install a rooted stock ROM on captivate?

Hi all,
I installed CM7 the latest nightly build on my captivate. How do i get to my old ROMs (cognition, serendipity...). I have read a lot of threads, and also have tired few solutions, but I have no clue why my odin hangs at "Donot Turn of the Target"
I waited for a long time, on that message, probably half an hour and then i had to pull out the USB cable. Now i am stuck at < phone + ! + computer > screen.
The one click odin i am using is from the following thread...
http://forum.xda-developers.com/showthread.php?t=731989&highlight=odin+one+click
Can anyone please guide. Thank you.
I have no idea, what happened. I have done this some 10s of times, and everytime it got hanged at <DO NOT TURN OFF THE TARGET>. But suddenly it worked.
What all i did --
0. Download 1 Click Odin from
http://forum.xda-developers.com/showthread.php?t=731989&highlight=odin+one+click
1. Took out the battery and wire of the soft-bricked phone.
2. Held power - and + button together, and inserted the usb cable.
3. Inserted the battery, and within a second phone entered <Download Mode>.
4. Removed the usb cable.
5. Started the Odin. (With NO administrator mode and NO windows XP compatibility). That is I just double clicked the ODIN in windows 7.
6. Attached USB wire back to the phone.
7. Phone detected on one of the COM Ports.
8. Pressed Start button.
This all I have done some 10s of time... but the only thing extra i did this time was --
9. Cross your hands, and genuinely pray... that it works.
and it worked.
It seems like 9 is the most important step.
I hope this helps others too.
Try odin again. The one you used should work. Get your phone into download mode and run odin. If you can't get download mode, try and see if odin recognizes your phone anyway with the phone ! computer screen. If it does, flash oneclick from there. That will give you stock eclair.
Sent from my SAMSUNG-SGH-I897 using XDA App
Phone should still be able to be flashed using Odin. I'd fire it up again and try. the phone-!-computer.. is another download mode, an "unofficial" download mode

[Q] Have I ruined my in law's phone? Can anyone help me please?

My father in law bought a new phone SGS on O2 and I offered to unlock it as I have unlocked my husbands last week (he's was on O2 as well but in 2.1 or 2.2.1 version I think-froyo?)
Before I continue may I say I know you guys out there know so much more than me and I really need your help. I really tried to help unlocking this phone and for hours I searched and read things like reboot, download mode, recovery mode, flashing, JKV and so many other words and letter that I could not understand. Very few I understood in the end but may have messed up badly (?).
Please, I need help and please treat me as if I were your mum or even grandma. Step by step in simple normal English please.
My father in law's version is 2.3.3
I tried unlocking it the way I unlocked my husband's but didn't work. After looking for hours I thought that the best way to do it would be to downgrade from 2.3.3 (gingerbread (?)) to 2.2.1 (froyo (?)) and then unlock it.
I found this:
http://forum.xda-developers.com/showthread.php?t=1089989
and tried to follow it.
I downloaded EZRom and EZboot-Froyo-1.0.tar.md5 from the same post.
I followed:
•Download the right version from section above
•Reboot your phone into Download mode
•Connect your phone to computer
•Run EZOdin
•Select EZboot-Froyo-1.0.tar.md5 or EZboot-GingerBread-1.0.tar.md5as a PDA file in EZOdin
•Check the "Phone Bootloader Update" checkbox
•Click Start
I waited for the phone to turn off and feel the little vibration but didn't. Instead it just froze at the first screen when you turn on the phone. The black background with white letters: Samsung Galaxy...
I waited and waited and as nothing was happening I then I took the battery out. Put it back in and tried turning it on. I wouldn't it would just stop and that same screen, the black and white one.
I reread
•Wait until phone reboots and make it reboot into Recovery
SO then I remembered in the many threads I read about the recovery mode so 3 clicked vol up + button at them bottom and turn on bottom.
It gives me a few options. When I click on reboot all it does is show me the black and white screen again and nothing else. ah!!!
I took the battery off and put it back on many times, I also selected the fatory reset option and tried different buttons but nothing. Please help me.
I'm happy to phone any of you guys to help me and guide me even if it's just to put the phone back to what it was before, turning on normally, etc. I'm feeling really sad and a bit stressed as these days are supposed to be a nice time to spend with my little ones and family.
Anyway, please ask me anything.
Thank you so much in advance. I really hope I didn't do anything wrong and I'm just stuck because I'm ignorant in this matter. Thank you
I was never a fan of EZ-stuff.
That said, think you can easily solve that flashing your phone with odin and a proper rom. At this point i am unclear about what bootloaders you have on your phone since you've tried a downgrade.
Without getting into further details (sorry, at work atm). You can get tutorials easy for all of this around this forum.
I'd get Odin, get a proper stock rom from samfirmware with bootloaders included and flash it fresh from start with that. Doesn't really matter if it's froyo or ginger as long as it includes bootloaders.
You'll be left with a working phone at this point.
From here, if you still want to try to unlock it, i'd flash a kernell that would get me root (like the ChainFire one) since i find this the safest and easiest way of getting root on your phone and do a backup of your EFS partition (preferably saved in your computer or wherever outside your phone). This is very important, if you lose of mess up with this part of your phone it will be a pain.
Now, there are several ways of unlocking this phone, the only one i found to be most reliable (but not the easiest one) is to manually edit the nv_data.bin file (located in your EFS partition in hexadecimal.
There's a tut right here
http://forum.xda-developers.com/showthread.php?t=761045&highlight=unlock
Thank you so much for taking the time to reply although you are working!!! Really appreciate it.
I'll try your suggestion but I don't know how to choose the right stock rom with bootloader from samfirmware. I went to the website and registered but don't really know what to do.
I know you are working so might not be able to help me, may be someone else?
Here's where I am. Update. I found a list of firmware. This is the last one on Samfirmware.com.
Europe Samsung I9000 Firmwares.
I9000XXJVS ##
512.PIT
2.3.5
2011 September 8
CSC = I9000OXAJVS
DOWNLOAD
Things I need: (I think)
-Download a firmware (should I use the lastest one?) or 2.2 or 2.3.3? . Is there one better than the other? or is it my choice? How can I choose the best one for me?
-Odin. I have OdinMultiDownloader v4.03 in my desktop. Is that the best thing to use or should I use Ezodin. I don't know what the difference is.
-(Do I need to download or do anything else?)
Things I should do:
-Put phone in download mode
-Plug it to the laptop
-Open Odin (or Exodin?)
-click PDA. Choose the fie I downloaded-firmware.
(-after this I don't know what else I should do or tick or untick)
Am I in the right track or completely off it?
Thank you again to anyone taking the time to read this.
Download Jvt From sammobile. com, you need Odin on your PC (1.7 or 1.8) plus Samsung drivers. Read there flashing guides carefully, check you have download
Mode, battery charged > 50% etc
There is also a video on youtube which shows you how to upgrade to jvt.
Sent using TCP/IP
Sounds like you've got the boot-loop problem, which means that you most likely "soft-bricked" the phone. Don't worry, this isn't that big of a deal and can be fixed with relative ease. I agree with the posters above, a clean flash with Odin will probably fix your problem and get you out of the boot-loop.
I'll go into a bit more detail with some steps (feel free to correct me if I missed anything)
1. Download Odin 1.85 here.
2. Head over to Samfirmware.com and grab the latest firmware for the phone. I recommend Gingerbread 2.3.5 (JVT).
3. Make sure your computer has the proper drivers installed so it can communicate with your Samsung Galaxy GT-I9000. If you've flashed the phone before with your computer then you probably have the drivers installed, but here's a link for them just in case: Samsung USB Drivers
4. Enter download mode on your phone, depending on your firmware, it could be Vol down + power + home OR Vol up + power + home. Pull the battery out, pop it back in, and hold those three buttons until the phone turns on.
If you can't enter download mode with the 3-button hold method, then you might have to do so via ADB with the command "reboot download".
Getting into download mode is pretty critical, as you cannot progress further without it.
5. Once you're in download mode (should see a triangle with an Android shoveling stuff in it), plug your phone into your computer's USB port and open Odin. In Odin, press "Reset" on the right hand side. Odin should be able to detect your phone (this is indicated by a yellow box on the left side). I'm using a PC, so inside the yellow box I see something like this: 0:[COM9]. On a Mac it probably says something different, but as long as you see the yellow box appear then it's all good.
If you don't see the yellow box, then there's no communication between your phone and the computer, which means that you may have to reinstall the Samsung USB drivers.
6. With the contents in the firmware package that you downloaded from Samfirmware.com extracted, load them onto Odin accordingly.
PIT: use s1_odin_20100512.pit
PDA: JVT (sometimes the PDA is labeled CODE instead)
PHONE: JVT (sometimes labeled as MODEM instead)
CSC: use HOME-MULTI-OXAJVT (should be about 9.5 MB in size)
Since your father-in-law's phone was originally 2.3.3, you shouldn't have to alter the bootloader with Odin, so leave the bootloader field empty.
7. Once you've loaded up all the necessary files, make sure Re-partition and Auto-reboot is checked. Leave the rest of the checkboxes as it.
8. Press Start. This should initialize the flashing of the new firmware. After the phone has been flashed, it should reboot automatically and should hopefully be able to get past the Galaxy S black and white logo (aka. boot loop).
9. The phone should be in working order now. I used this method to unlock my SGS: SIM Unlock on the SGS. With this method, your phone needs to be rooted, so head on over to ChainFire's thread here to install his kernal which is already rooted.
Flashing firmware can be pretty scary since nobody wants to end up with a brick that costed $400 and it seems like so much can go wrong, but hopefully the steps I've provided helped. Good luck!

[Q] Newbie Need help! about how to flash a rom on Galaxy Tab GT P1000

Hi guys
I'm pretty much a newbie when it comes to flashing a rom such as ICS or any latest rom that is available for my Galaxy Tab so i really need help with this to avoid problems. First how do i know whether my galaxy tab is GSM or CMDA ? i checked my WIFI settings and it says GSM/WCMDA what does these means ? I can use 3G if you needed to know.
And what tools and applications do i need ? to flash a rom such as ICS or any latest stable rom. i just factory reset my Galaxy Tab GT P1000 already as it's causing problems for me such as freezing everyday and restart by itself.
Currently my Galaxy Tab is on 2.3.3 GingerBread Android. The stock version of it was Froyo i guess that is 2.2 right ? and yeah i updated my tab from Kies few months ago to gingerbread of course. And yes i already rooted my Galaxy Tab few months ago but i just factory reset it today i guess the root is gone now ?
What are the latest and stable ICS/JB version for my Galaxy Tab GT P1000 ? please do guide me to successfully installing them.
hope someone is able to help me with this as i am going to flash it today.
thank you very much
Edit is highlighted by blue font. Mistake highlighted by red font.
I was just about to write a guide for my niece, here goes: -
Please read other guides to be more understanding of flashing. Below is a quick step only. Just in case the good long guides are too long and too complex. Hopefully with a short guide + long guide, it's easier and cover both sides / requirements. Sorry that it was too short for dc2mx, hope he recovers well.
pre-requisite. --->>> magic action.
Hold power button 8 seconds and it will FULLY SHUTDOWN. Don't let it be ON whole night. Battery does not charge during DOWNLOAD mode and not charge in RECOVERY mode. That's why I write in step 16 about this magic 8 seconds fully shutdown.
Hold power button 4 seconds and it boots up.
Hold power button 12 seconds will shutdown then boots. Not adviced. Because it becomes boot-loop.
OK, may some filenames are wrong, but they carry the same meaning. Hence please forgive my short-coming or spelling mistake or naming error.
make sure battery is 100% charged up.
no need root, hence skip rooting step.
download this file >>>GB-Stock-Safe-v5<<< link is provided another time by http://forum.xda-developers.com/showthread.php?t=1881981 - thanks thanks thanks to priyana priyana priyana.
make sure to install USB driver first, then plug in TAB to PC, wait few minutes to let it recognize, install and stable_lise <<<stabilize>>>. Takes time. No need to copy anything into it. This is just to ensure that the drivers were installed properly and that it successfully recognized the device so that FLASHING can be carried out.
reboot holding VOL_DOWN to go into DOWNLOAD MODE. You should see the word DOWNLOAD with a big triangle symbol.
direct use Odin software to flash the >>>GB-Stock-Safe-v5<<< OVERCOME RE-STOCK version 5 (the file is TAR format), download link above. See more details somewhere else. Sorry for being lazy uncle.
make sure to select a file named <<<<mr.pit>>>> for the pit section, MUST.
select the <<<<rom file.TAR>>>> format for PDA <<<I wrote WRONG previously into phone section|>>>, MUST. Very terribly sorry to dc2mx and anyone else affected.
select <<<<modem.bin>>>> for phone section else can't call, but not need now, later will have, can skip. Unless you wanna stick to 2.3.3
tick 3 items, A = re-partition, B = auto-reboot, C = F.reset.time. MUST.
click FLASH, wait 2.5 minutes, finished, auto reboot. You should see the USB connect YELLOW highlight successful before able to click FLASH.
then reboot again into Download mode and Odin again to flash the KERNEL only <<<002001-Overcome_Kernel_v4.0.0.tar>>> because it contains most importantly CWM (clock work mod), which is a TAB_self_rom_flashing. (newbie term).
Then download a CM9 or CM10 or whatever you want. as for me, as of writing I'm using alroger's 8th November version. Thanks to alroger, humeros, cdesai, and so many more.....http://forum.xda-developers.com/showthread.php?t=1869477 Put into TAB's internal sdcard. Fastest flash. My external SD is cheap type, hence slow.
Flash it via reboot holding VOL_UP to go into RECOVERY mode. Select the file/rom that you chosen.
You'll see flash progress go to 10% then reboot.
Then reboot loop non stop. Hold power button for 8 seconds for it to shutdown fully.
Why? because flashing the first 10% puts in a new kernel with new MTD partition and everything behinds it can't recognize it, can't find it hence boot loop.
Enter RECOVERY again, reboot holding VOL_UP. If failed again. Don't worry, keep trying, I had to try 10 times. My first manual reboot went into CWM successfully but I didn't understand and realize, hence did not flash the file again. Then reboot normally, obviously it just boot-loops. Tried to go into CWM the 3rd time but not succesful, it just boot-loops. try so many times, with full shutdown and wait many minutes in between. I think around 10 times or more later went into CWM finally. God bless.
Reboot again into RECOVERY and flash one more time and WIN, DONE.
finished.
cx5 said:
I was just about to write a guide for my niece, here goes: -
make sure battery is 100% charged up.
no need root, hence skip rooting step.
download this file >>>GB-Stock-Safe-v5<<< link is provided another time by http://forum.xda-developers.com/showthread.php?t=1881981 - thanks thanks thanks
make sure to install USB driver first, then plug in TAB to PC, wait few minutes to let it recognize, install and stable_lise. Takes time.
reboot holding VOL_DOWN to go into DOWNLOAD MODE.
direct use Odin to flash the OVERCOME RE-STOCK version 5, download link above. See more details somewhere else. Sorry for being lazy uncle.
make sure to select mr.pit for the pit section, MUST.
select the rom file.TAR for phone section, MUST.
select modem.bin for phone else can't call, but not need now, later will have, can skip. Unless you wanna stick to 2.3.3
tick 3 items, A = re-partition, B = auto-reboot, C = F.reset.time. MUST.
click FLASH, wait 2.5 minutes, finished, auto reboot.
then Odin again to flash the KERNEL only <<<002001-Overcome_Kernel_v4.0.0.tar>>> because it contains most importantly CWM (clock work mod), which is a TAB_self_rom_flashing. (newbie term).
Then download a CM9 or CM10 or whatever you want, for me, as of writing I'm using alroger's 8th November version. http://forum.xda-developers.com/showthread.php?t=1869477 Put into TAB's internal sdcard. Fastest flash.
Flash it via reboot holding VOL_UP to go into RECOVERY mode. Select the file/rom that you chosen.
You'll see flash progress go to 10% then reboot.
Then reboot loop non stop. Hold power button for 8 seconds for it to shutdown.
Why? because flashing the first 10% puts in a new kernel with new MTD partition and everything behinds it can't recognize it, can't find it hence boot loop.
Enter RECOVERY again, reboot holding VOL_UP. If failed again. Don't worry, keep trying, I had to try 10 times.
Reboot again into RECOVERY and flash one more time and WIN, DONE.
finished.
Click to expand...
Click to collapse
Hi thank you for providing with this guide but it doesn't answer any of my questions i am asking but anyway, i am confused with step 4 i have already downloaded GB Stock Safe V5 from the thread you linked. what do you mean by install and Stable_lise ? i have my USB Cable connected to my Galaxy Tab and it shows as Removable storage. What do i need to copy in it ?
If it's possible can you provide much more detailed and clearer instructions ? which are definitely newbie proof.
EDIT: Nevermind i got what you're talking about but i did those 11 steps then now Odin says FAIL on the application about something unable to write partion or something like that. now my Tab is frozen on Do not turn off target screen, Did my Tab just got bricked ? how do i restart it ?
cx5 said:
I was just about to write a guide for my niece, here goes: -
make sure battery is 100% charged up.
no need root, hence skip rooting step.
download this file >>>GB-Stock-Safe-v5<<< link is provided another time by http://forum.xda-developers.com/showthread.php?t=1881981 - thanks thanks thanks
make sure to install USB driver first, then plug in TAB to PC, wait few minutes to let it recognize, install and stable_lise. Takes time.
reboot holding VOL_DOWN to go into DOWNLOAD MODE.
direct use Odin to flash the OVERCOME RE-STOCK version 5, download link above. See more details somewhere else. Sorry for being lazy uncle.
make sure to select mr.pit for the pit section, MUST.
select the rom file.TAR for phone section, MUST.
select modem.bin for phone else can't call, but not need now, later will have, can skip. Unless you wanna stick to 2.3.3
tick 3 items, A = re-partition, B = auto-reboot, C = F.reset.time. MUST.
click FLASH, wait 2.5 minutes, finished, auto reboot.
then Odin again to flash the KERNEL only <<<002001-Overcome_Kernel_v4.0.0.tar>>> because it contains most importantly CWM (clock work mod), which is a TAB_self_rom_flashing. (newbie term).
Then download a CM9 or CM10 or whatever you want, for me, as of writing I'm using alroger's 8th November version. http://forum.xda-developers.com/showthread.php?t=1869477 Put into TAB's internal sdcard. Fastest flash.
Flash it via reboot holding VOL_UP to go into RECOVERY mode. Select the file/rom that you chosen.
You'll see flash progress go to 10% then reboot.
Then reboot loop non stop. Hold power button for 8 seconds for it to shutdown.
Why? because flashing the first 10% puts in a new kernel with new MTD partition and everything behinds it can't recognize it, can't find it hence boot loop.
Enter RECOVERY again, reboot holding VOL_UP. If failed again. Don't worry, keep trying, I had to try 10 times.
Reboot again into RECOVERY and flash one more time and WIN, DONE.
finished.
Click to expand...
Click to collapse
thanks for this, it helps alot
can you provide links to the files?
I see there is a link for the >>>GB-Stock-Safe-v5<<< but I don't see links for
OVERCOME RE-STOCK version 5, the kernel is there but no OVERCOME RE-STOCK version 5..
thank you again
oh, and I suppose that "stable_lise" refers to stabilize?
See my signature for overcome new links.
(Actually same as his link)
It is GB stock safe v5, should no be called Overcome version 5.
Sent from my GT-P1000 using xda app-developers app
thanks priyana!!
I searched a lot about this matter and found all sorts of information..
I presume you know around the P1000, can you take a look at this thread, it is a more detailed question
http://forum.xda-developers.com/showthread.php?t=1988047
Hey guys i really need help, i just posted yesterday and i am shocked that no one replied to me.
This is what i did yesterday i downloaded GB-Stock-Safe-v5, Overcome_Kernel_v4.0.0.tar, and CM10 P1000, md5sum: 157da0dc187216fa924da45182e1307e
OK i am going to repost now i already did those 10 steps but during step 11 Odin says FAIL on the application about something unable to write partion or something like that. now my Tab is frozen on Do not turn off target screen, Did my Tab just got bricked ? how do i restart it ?
So i was unable to turn it off. it was out of battery today, thought it might turn on if i charge it back. but i was both right and wrong it does boots up but now it gives me a Phone and a yellow /!\ Computer icons now, Anyone knows what is happening ?
dc2mx said:
Hey guys i really need help, i just posted yesterday and i am shocked that no one replied to me.
OK i am going to repost now i already did those 10 steps but during step 11 Odin says FAIL on the application about something unable to write partion or something like that. now my Tab is frozen on Do not turn off target screen, Did my Tab just got bricked ? how do i restart it ?
So i was unable to turn it off. it was out of battery today, thought it might turn on if i charge it back. but i was both right and wrong it does boots up but now it gives me a Phone and a yellow /!\ Computer icons now, Anyone knows what is happening ?
Click to expand...
Click to collapse
Hi there. The phone-exclamation-pc thing is another download mode.
At least you still have your bootloader.
Just make sure in the mean time you powered it off and charge it for over 4hrs. You don't want the power to run out.
In the download mode, is Odin detecting the tab? if so, you should still have very good chance to revive it.
Now, question:
- did you use Odin v1.7 included in the GB-stock-safe-v5 package or using other? Remember it is important to use the correct Odin version.
There should be little reason for the flash to fail on repartition if you follow the guide. If you haven't got it, see my signature, and go there to get the PDF guide and jump to page 7.
If you have already followed exactly, then there is a chance you have a damaged internal NAND chip. There are ways to go around that, but lets not go there first.
priyana said:
Hi there. The phone-exclamation-pc thing is another download mode.
At least you still have your bootloader.
Just make sure in the mean time you powered it off and charge it for over 4hrs. You don't want the power to run out.
In the download mode, is Odin detecting the tab? if so, you should still have very good chance to revive it.
Now, question:
- did you use Odin v1.7 included in the GB-stock-safe-v5 package or using other? Remember it is important to use the correct Odin version.
There should be little reason for the flash to fail on repartition if you follow the guide. If you haven't got it, see my signature, and go there to get the PDF guide and jump to page 7.
If you have already followed exactly, then there is a chance you have a damaged internal NAND chip. There are ways to go around that, but lets not go there first.
Click to expand...
Click to collapse
Yes, i already connected my tab to power charger now. Of course i used Odin v1.7 that is included in GB-stock-safe-v5 package. but during Odin process i waited about 5mins then i went to see how is it going, then there's a FAIL in red above the first box. and my Tab is stuck a Do not turn off target mode.
I only did those instructions cx5 provided. So now i am stuck with Phone /!\ Computer icons screen. What am i going to do next ? And do you mean this guide ? https://docs.google.com/file/d/0B7k...EyNS00Yzg5LWE0MTktYmYyMjA1MThmYzQz/edit?pli=1 if yes, i haven't read it yet.
This is what i did yesterday i downloaded GB-Stock-Safe-v5, Overcome_Kernel_v4.0.0.tar, and CM10 P1000, md5sum: 157da0dc187216fa924da45182e1307e
What are the differences between P1000L and P1000N ? which CM10 files are right for my tab ?
Are these files that i am going to need ? please do refresh this thread every 5 mins or so. since i need help i will be here too. thank you
UPDATE: OK i just connected my Tab to power charger. but when i unplugged it. it turns off. i guess i need to leave it there for 4 hours to charge it ? i can't check whether Odin are able to detect my tab since i unplugged it and it turns off.
UPDATE2 Hmm my tab is blinking, it was on Phone /!\ Computer Icons screen. but now it's blinking, i meant it went to Phone /!\ Computer Icons screen then back to black screen every 10 seconds. is this normal ?
yes, try charge for more than 4hrs and hope the power goes in.
cx5 instruction seems correct, but it is best to look at page 7 of the guide for 100% accurate placement of the files.
the P1000L/N are Latin American tab that has different touch screen driver.
priyana said:
yes, try charge for more than 4hrs and hope the power goes in.
cx5 instruction seems correct, but it is best to look at page 7 of the guide for 100% accurate placement of the files.
the P1000L/N are Latin American tab that has different touch screen driver.
Click to expand...
Click to collapse
Hmm ok i think i know what went wrong during Odin process. cx5 said select the rom file.TAR for phone section, MUST. but i just read this guide https://docs.google.com/file/d/0B7k...EyNS00Yzg5LWE0MTktYmYyMjA1MThmYzQz/edit?pli=1 and it says click PDA and select GB_Stock_Safe_V5,tar and then click Phone.
i didn't click PDA as cx5 instructions didn't mention it. and that's why i am getting FAIL on Odin ?
Anyway, i guess i leave it to charge for 5 hours. then Test whether Odin is able to detect my TAB or not. see you in 5 hours later Priyana. hopefully you're online as i am not sure what to do next after Odin is able to detect my tab.
after charging, boot to download mode again, you may get that same screen like before.
In your PC prepare the Odin exactly like the page 7 of PDF.
Connect the tab to the PC and if you see the tab detected, just flash away, hopefully no error, and it should reboot itself if I am not mistaken, and you get stock GB rom.
Then just continue with the guide, to flash Overcome Kernel 4.0 tar.
After that you will have a CWM recovery, ready to flash CM10
priyana said:
after charging, boot to download mode again, you may get that same screen like before.
In your PC prepare the Odin exactly like the page 7 of PDF.
Connect the tab to the PC and if you see the tab detected, just flash away, hopefully no error, and it should reboot itself if I am not mistaken, and you get stock GB rom.
Then just continue with the guide, to flash Overcome Kernel 4.0 tar.
After that you will have a CWM recovery, ready to flash CM10
Click to expand...
Click to collapse
OK so i am currently charging my Tab and it's blinking from Phone /!\ Computer screen to black screen every 10sec above. Does this screen disappear after fully charging it ? it seems that i am stuck at this screen now. but i can't turn it off and go to the previous hold Volume down and hold power button Do not turn off Target download mode.
Or Does Odin is able to detect my Tab on this Phone /!\ Computer screen too ? since you said it's another download mode please do correct me if i am wrong
yes Odin should detect it at this screen too.
If it doesn't, it will be very hard to fix.
I am surprised that you can't turn it off. Doesn't sounds so good, as it may deplete the batt completely.
Did you try to press the power button for a few seconds (5-10 seconds) to force it off completely?
priyana said:
yes Odin should detect it at this screen too.
If it doesn't, it will be very hard to fix.
I am surprised that you can't turn it off. Doesn't sounds so good, as it may deplete the batt completely.
Did you try to press the power button for a few seconds (5-10 seconds) to force it off completely?
Click to expand...
Click to collapse
Yeah my Tab was turn on for a whole yesterday. since i can't turn it off as it froze at Do Not Turn Off Target download mode. and today i saw the screen was off. then i went to turn it on but nothing i guess the battery is depleted. so i went to charge it and tried turning it on. it does boots up but now showing me this "Phone yellow /!\ Computer screen.
Okay, i just tested trying to shutting it down by holding Power button for 10seconds. but it seems that i can't turn it off. but the Tab itself is a little hot.
I have another question to ask, now i am stuck in this screen, and i have no idea it's charging or not. is this normal ? or usually it shows it's battery charging notification ?
UPDATE: It seems that my Tab is now turn off? it's not showing me the "Phone yellow /!\ Computer screen" now. it looks like it's turn off. nothing there just black
just leave it like this with the charger for maybe 8hr, since it has completely depleted before.
Battery charging animation I heard resides in the kernel.
So if the tab is flashed incorrectly, the battery animation will not be there.
It should still be charging (hopefully). The only way to be sure is to leave it charging for really long.
priyana said:
just leave it like this with the charger for maybe 8hr, since it has completely depleted before.
Battery charging animation I heard resides in the kernel.
So if the tab is flashed incorrectly, the battery animation will not be there.
It should still be charging (hopefully). The only way to be sure is to leave it charging for really long.
Click to expand...
Click to collapse
Hmm Okay, I'm going to let it stay there charging for at least 8 hours +. So be sure to check this thread regularly priyana as i really need your help. Thank you very much
dc2mx said:
Hmm Okay, I'm going to let it stay there charging for at least 8 hours +. So be sure to check this thread regularly priyana as i really need your help. Thank you very much
Click to expand...
Click to collapse
Ugh.. i know that it's just 5 hours+ But i was trying to turn on my tab to test whether Odin can detect my tab. but it seems that it won't power on. i guess it's dead ?
Damn i should have waited for your reply first priyana before doing anything. i just didn't do a important step which is "click PDA and select GB_Stock_Safe_V5,tar and then click Phone" instead of "select the rom file.TAR for phone section, MUST" which i thought click phone and select the tar. but it wasn't my fault as someone here posted the instructions that is misleading and missing the important step. Oh well....thanks for nothing,
Anyway, priyana, i really appreciate you are trying to help me. thank you very much buddy
Don't give up. Just continue charging. Many have experienced worst. I don't believe yours is bricked.
Sent from my GT-I9300 using xda app-developers app
priyana said:
Don't give up. Just continue charging. Many have experienced worst. I don't believe yours is bricked.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Erm.. i can't even turn it on so i guessing it's dead. i don't think i am able to bring it back alive though

Categories

Resources