Galaxy Note stuck at boot screen after OTA update - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Hi, My note is stuck at boot screen after the official OTA update. I tried googling but most seems to pertain to Rooted/flashed phones.
Mine is a new note which has not been rooted at all in the past. I downloaded to OTA update and it has been stuck at the bootscreen for the past few hours.
Any help appreciated!

1. Try pulling out the battery for a few minutes.
2. Boot into recovery mode and wipe cache and dalvik cache.

should i also wipe the data/factory reset in recovery mode?

No. God forbid, then you might end up with a superbrick

Thanks for your help
Sent from my GT-N7000 using XDA

Unable to enter recovery mode
Hey I got similar problem, my phone gets stuck at Samsung logo screen. I am unable to enter recovery mode. When it shows android update screen after pressing recovery mode combination, my phone restarts.
Is there anyway I can get back normal mode without losing data on phone

indianphoenix said:
Hey I got similar problem, my phone gets stuck at Samsung logo screen. I am unable to enter recovery mode. When it shows android update screen after pressing recovery mode combination, my phone restarts.
Is there anyway I can get back normal mode without losing data on phone
Click to expand...
Click to collapse
Keep them pressed for 3 seconds more then you end up to recovery. They need to be pressed while booting the device from reboot or off state, then you will end up in recovery or download mode.
Sent from my GT-N7000 using Tapatalk 2

Yesterday, I received an OTA on my galaxy note and now it is also stuck in boot screen with the breathing samsung logo.
I tried to go into recovery mode using the 3 button combo, but it wouldnt enter into recovery mode. I get the green android logo with wire mesh and the phone reboots.
Can someone help me to boot my phone?

Got mine backup and running after OTA update gave me Samsung logo freeze issue
So after the 7MB OTA stability patch mine too was stuck on samsung logo.
Kies wouldn't recover it and putting into download mode or recovery mode didn't help. I too tried to go into recovery mode using the 3 button combo, but it wouldnt enter into recovery mode. I get the green android logo with wire mesh and the phone reboots but i didn't at the time try for 3 more seconds.
I then used ODIN and applied a downloaded Aussie Gingerbread ROM as i couldn't find Aussie ICS ROM. With my plan to do a Kies/wifi update to ICS. This caused acore and other processes to crash every few seconds. I then did a factory reset which got it stable and then tried to update to ICS but the phone said there were no updates available. Then I applied the international ICS using ODIN so i'm back were i was two days ago before the stupid 7MB patch.
Unfortunately, I don't think i can get anymore OTA updates but after the 7MB one i don't think i want to.
Long story short i think you should be able to go into recovery mode do a factory reset and it should be OK.

bigwalabig said:
Hi, My note is stuck at boot screen after the official OTA update. I tried googling but most seems to pertain to Rooted/flashed phones.
Mine is a new note which has not been rooted at all in the past. I downloaded to OTA update and it has been stuck at the bootscreen for the past few hours.
Any help appreciated!
Click to expand...
Click to collapse
U can download stock ics and flash it through pc odin. Cheers.
Press 3 combo button to enter download mode and plug ur cable data once u have open pc odin with downloaded rom on pda :beer:
Sent from my GT-N7000 using xda premium

ODIN voids warranty?
I have the same issue after receiving 7MB OTA update. I am unable to go into recovery mode(same green robot and wire mesh etc...), so i am going to use ODIN method... but will flashing stock ROM using ODIN void my warranty?? I am not rooted.
Thanks.

vinit.the.one said:
I have the same issue after receiving 7MB OTA update. I am unable to go into recovery mode(same green robot and wire mesh etc...), so i am going to use ODIN method... but will flashing stock ROM using ODIN void my warranty?? I am not rooted.
Thanks.
Click to expand...
Click to collapse
To flash yoi have to root...which voids warranty
But not to worry
Check the videos in my sig...it will explain how to succesfully unroot and get back to normal :good:

Rulinglionadi said:
To flash yoi have to root...which voids warranty
But not to worry
Check the videos in my sig...it will explain how to succesfully unroot and get back to normal :good:
Click to expand...
Click to collapse
Thanks.... but this is my aunt's phone, so rooting is not an option. I use HTC Hero... and we have RUU which we run on the PC and everything is restored to stock.... it removes root if you have it and also runs without root. Is there anything similar for samsung devices?
Also, now I am considering going for warranty repair... didnt want to do that at first as i have a really bad experience with HTC service centers... now lets see what samsung does..!!

Same problem here please find a fix!!

Rulinglionadi said:
To flash yoi have to root...which voids warranty
But not to worry
Check the videos in my sig...it will explain how to succesfully unroot and get back to normal :good:
Click to expand...
Click to collapse
You don't need root to flash stock with PC Odin, and flashing any stock does not affect warranty. To use Odin you need phone in download mode (vol down, home and power until reboot into download)
Sent from my GT-N7000 using xda premium

SOLVED!
vinit.the.one said:
I have the same issue after receiving 7MB OTA update. I am unable to go into recovery mode(same green robot and wire mesh etc...), so i am going to use ODIN method... but will flashing stock ROM using ODIN void my warranty?? I am not rooted.
Thanks.
Click to expand...
Click to collapse
Just flash it using the same os version you already have installed in my case I had the same problem with this little ota update and I've just flash it with the same ics version that was installed and my phone was back with all my stuff and rooted... once you finish doing the re flash you'll get an on screen message saying "Fail to update try using samsung kies on your computer" or something like that...

Thanks... but I went for warranty repair .. and I got it back in 2 hours..... unfortunately I lost all my data .. even on external partition. Now it is on ICS and still I have a notification for available update ... which I wont do.
Anyone has had success with that update?
Sent from my Hero using xda app-developers app

Related

[Q] Bricked Galaxy Mini

Hi, I live in Egypt for a while and I bought last month a Mini. Everything was going just fine, I was using Odin many times to try new roms, and CWM Recovery to give a try to custom roms, without problems. Yesterday morning I flashed my device with the 2.3.6 rom that I found on this forum, apparently made for Latin America. Since that moment, my mobile is on boot loop, i can't do anything, I only can access downloading mode, I tried to reflash gingerbread 2.3.4, and2.3.5, it goes well, Odin gives me the PASS message, but still my mobile is forever rebooting at Samsung logo. I can't access recovery.
What to do? Is it bricked and do I have to send it to Samsung Center or is there hope to fix it by myself?
Thank you for any help...
Yohan
u cant even enter recovery?if u can,just wipe cache and data..
Sent from public phone using 10cents.
ybregeon said:
Hi, I live in Egypt for a while and I bought last month a Mini. Everything was going just fine, I was using Odin many times to try new roms, and CWM Recovery to give a try to custom roms, without problems. Yesterday morning I flashed my device with the 2.3.6 rom that I found on this forum, apparently made for Latin America. Since that moment, my mobile is on boot loop, i can't do anything, I only can access downloading mode, I tried to reflash gingerbread 2.3.4, and2.3.5, it goes well, Odin gives me the PASS message, but still my mobile is forever rebooting at Samsung logo. I can't access recovery.
What to do? Is it bricked and do I have to send it to Samsung Center or is there hope to fix it by myself?
Thank you for any help...
Yohan
Click to expand...
Click to collapse
Just remove the battery and stop your phone.
Put the battery in again.
Go to recovery mode by pressing Home + Power button at the same time.
In the reocevey choose wipe data/factory reset option.
Reboot your device after you are done.
You mobile will boot up fine.
Thank you for your answers but I wanna insists on a point: I can't access recovery at all, the phone show me the samsung logo for about half a second then restarts, and is looping in this state. No recovery, only downloading mode and RAMDUMP Mode (ARM9 mode) & Emergency Dload Mode (ARM9 Mode). Nothing else is avalaible.
Helppp
ybregeon said:
Hi, I live in Egypt for a while and I bought last month a Mini. Everything was going just fine, I was using Odin many times to try new roms, and CWM Recovery to give a try to custom roms, without problems. Yesterday morning I flashed my device with the 2.3.6 rom that I found on this forum, apparently made for Latin America. Since that moment, my mobile is on boot loop, i can't do anything, I only can access downloading mode, I tried to reflash gingerbread 2.3.4, and2.3.5, it goes well, Odin gives me the PASS message, but still my mobile is forever rebooting at Samsung logo. I can't access recovery.
What to do? Is it bricked and do I have to send it to Samsung Center or is there hope to fix it by myself?
Thank you for any help...
Yohan
Click to expand...
Click to collapse
hey man i've already had that problem..coz i flash 2.3.6 and encountered same problem but i manage to fix it.. you need to enter recovery mode... Note: you need to hold the home & power button and wait for the samsung logo to flash TWICE (2X),when the 2nd logo flash, just realease the buttons and your on recovery mode.just wipe/ data reset.. right now im using Ginger bread 2.3.6JKVT and its rooted also.
No, I can't access recovery sorry.
Connect your phone to your laptop.
Use ADB
Type this :
adb shell reboot recovery
That will take you to download mode,then you can flash rom again. It would be easier if you have a CWM installed
Sent from my GT-I5500-MADTEAM using Tapatalk
Shall I use Downloading mode to do this?
ybregeon said:
Shall I use Downloading mode to do this?
Click to expand...
Click to collapse
If you can't access recovery either falsh CWM recovery or Flash another firmware from Download mode. If you want to flash CWM recovery just follow the link below for Galaxy Mini and search CWM recovery.
I tried many times, since i have this problem, to flash and reflash, official roms, CWR, but nothing works, setup goes fine according to Odin, but still have the problem on my phone, still only downloading mode works, and still a flashing screen, just during the samsung logo.
No one can help me with my mobile???
ybregeon said:
No, I can't access recovery sorry.
Click to expand...
Click to collapse
did you wait for the samsumg logo to flash tiwce while holding the combo key? you see when im installing firmware using odin my laptop turn off coz i dont have a battery i thought my mini was brick because the process was not finish,so what happen i tried to acces recovery mode its only shows a computer icon & phone icon. but i manage to fix the problem i go to download mode and flash again another firmware. and everything goes fine..so how come that you cant access recorvery...i would suggest that you flash a firmware with 4 parts not a single package.
just try this www*mediafire*com/?br3r8fod5g3vud4 flash this firmware with Odin this will surely work please replace * with . brace my post count is not enough to post outside link
As long as you can enter download mode... you are safe. If you can... just flash it back with Odin.
Follow this step
http://forum.xda-developers.com/showthread.php?t=1107331
Thanks but no
dhlalit11 said:
just try this www*mediafire*com/?br3r8fod5g3vud4 flash this firmware with Odin this will surely work please replace * with . brace my post count is not enough to post outside link
Click to expand...
Click to collapse
Thank you for the link, i tried but still have the same problem. Could this be an EEPROM problem?
ybregeon said:
Thank you for the link, i tried but still have the same problem. Could this be an EEPROM problem?
Click to expand...
Click to collapse
Try booting up without micro sd nor sim card.
Sent from my neighbour’s android phone
i had a same problem too.
my phone cannot power on, and ONLY download mode only working.
i flashed it for so many time too, and it doesn't seem to fix the problem.
so any fix on this ?
To ybregeon and Tre3,
I had the exact same issue, only Download Mode and RAM Dump, but could not enter recovery mode. Tried flashing many ROMs, oneclick unbrick, Heimdall recovery etc. but still no solutions available, I tried many-many tricks with no luck. So I went to Samsung Service Center, and it turned out that the problem is in the mainboard. It took me one night before Samsung replaced the mainboard from my phone and it's been working well since. All free of charge.
I hope your warranty is still valid. Good luck.
Sent from my GT-S5570 using XDA App
distan7 said:
To ybregeon and Tre3,
I had the exact same issue, only Download Mode and RAM Dump, but could not enter recovery mode. Tried flashing many ROMs, oneclick unbrick, Heimdall recovery etc. but still no solutions available, I tried many-many tricks with no luck. So I went to Samsung Service Center, and it turned out that the problem is in the mainboard. It took me one night before Samsung replaced the mainboard from my phone and it's been working well since. All free of charge.
I hope your warranty is still valid. Good luck.
Sent from my GT-S5570 using XDA App
Click to expand...
Click to collapse
reflash the XXKPI/XXKPK 2.3.4 then flash the cmw, xxkpi and xxkpk is the safest stock gb rom to install
Flash odin and go to recovery mode and wipe.
It should work.

Bricked or Boot loop - help needed

Hi people!
I got bricked my galaxy mini gt-s5570, but not totaly (that means I can still use the download mode, and RAMDUMP ARM9 mode) but I can't power up the phone. That happened after I used ODIN for gt-s5570 and changed the Kernel (I forgot to make backup before), and device was working well with the new kernel, but after it I use the same step in ODIN to get back to the old one. So the result is, when I'm pushing the power key the screen starts to blinks and nothing more! But as I say download mode, and ARM9 mode are still working. Any solution for this?
just download the new firmware from samfirmware.com n flash it thru odin as u can go to download mode..n ur phone will be back to life again..
i accidently pressed thanks on ur first post
I can't, I don't have access to recovery mode, it doesn't work!
Explainations
ybregeon said:
I can't, I don't have access to recovery mode, it doesn't work!
Click to expand...
Click to collapse
I mean even when I flash an official rom with Odin, I still have the same problem, I am trying this since three days now and noway...
i think you tried to upgrade firmware not boot whenever you upgrade firmware it cant be downgrade it can just be more upgraded when you downgrade your firmware it will not boot up it will just show a black screen so just reinstall the firmware again and do not try to downgrade it

[Q] Superbrick, Softbrick, Pixel Salad ?huh?

Seriously can someone please explain to me what the heck the above mean? I get the notion of a brick but what the heck is the difference between Super brick? Hard / Soft Brick? Finally, not really brick but what's Pixel Salad!?
Thanks!
altrstar said:
Seriously can someone please explain to me what the heck the above mean? I get the notion of a brick but what the heck is the difference between Super brick? Hard / Soft Brick? Finally, not really brick but what's Pixel Salad!?
Thanks!
Click to expand...
Click to collapse
Soft brick= a FAILURE of the device that can be reverted by the user
Hard brick= a FAILURE of the device that has to be reverted via external devices see jtag
Superbrick= a FAILURE of the device where the only solution the service center and a replacement of the component that malfunctions.
Pixel salad = a problem of the graphics unit or the screen to display correctly the image and put instead random colored pixels on some areas of the screen or the whole screen.
This is my interpretation of those issues everyone can correct it if he thinks that those expansions are incorrect.
Hope it helped you understanding few of those issues.
GL& HF
Sent from my GT-N7000 using Tapatalk 2
Braxos said:
Soft brick= a FAILURE of the device that can be reverted by the user
Hard brick= a FAILURE of the device that has to be reverted via external devices see jtag
Superbrick= a FAILURE of the device where the only solution the service center and a replacement of the component that malfunctions.
Pixel salad = a problem of the graphics unit or the screen to display correctly the image and put instead random colored pixels on some areas of the screen or the whole screen.
This is my interpretation of those issues everyone can correct it if he thinks that those expansions are incorrect.
Hope it helped you understanding few of those issues.
GL& HF
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
You are spot on!!
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me ?
Is there any possibilities to get the phone fixed?
Thank you all for your answers allready
Wish u all a nice day
Nefret90 said:
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me
Click to expand...
Click to collapse
I'm not 100% sure, but performing a flash under lpf isn't recommended. How did you root lpf after flashing? And when you say "did a direct reboot" what do you mean? Also when you say doesn't turn on at all, do you mean no display whatsoever or enters Samsung boot loop? Are you able to enter recovery or download mode?
Sent from my GT-N7000 using xda premium
Nefret90 said:
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me ?
Is there any possibilities to get the phone fixed?
Thank you all for your answers allready
Wish u all a nice day
Click to expand...
Click to collapse
You should have read the warning about LPx kernels (LP1, LP5, LP6, LPY, LPF)
Wiping or flashing in recovery will probably cause superbrick.
Sent from my GT-N7000 using XDA
Nefret90 said:
Hi, I flashed N7000ZSLPF ICS with bootloader and rooted afterwards. Everything was perfect until i decided to flash cm9 nigthly signed.zip and did a direct reboot. Now nothing happens when i try to turn the phone on
What kind of brick is this? Can somebody please tell me ?
Is there any possibilities to get the phone fixed?
Thank you all for your answers allready
Wish u all a nice day
Click to expand...
Click to collapse
The way to go from ANY non-CM9-based ICS Rom to a CM9-based Rom is via Gingerbread.
You should've first used PC Odin to go back to GB, root your Rom, then flash CM9.
You have most probably superbricked your phone.
SpyderTracks said:
I'm not 100% sure, but performing a flash under lpf isn't recommended. How did you root lpf after flashing? And when you say "did a direct reboot" what do you mean? Also when you say doesn't turn on at all, do you mean no display whatsoever or enters Samsung boot loop? Are you able to enter recovery or download mode?
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Did root using cfs root trough Odin Pc. With a direct boot i mean that i just rebooted without doing the partiton thing just flashed the image and rebooted.
And when i say doesnt turn on at all i mean that absolutely nothing happens, no power at the screen no detection trough usb on pc no download mode or anything.
tryied to flash before and did just reboot, back then did just got the boot looop probem and did a recovery to ics. this last time i tried again to show a friend in a hurry and failed epicly
Nefret90 said:
Did root using cfs root trough Odin Pc. With a direct boot i mean that i just rebooted without doing the partiton thing just flashed the image and rebooted.
And when i say doesnt turn on at all i mean that absolutely nothing happens, no power at the screen no detection trough usb on pc no download mode or anything.
tryied to flash before and did just reboot, back then did just got the boot looop probem and did a recovery to ics. this last time i tried again to show a friend in a hurry and failed epicly
Click to expand...
Click to collapse
You are definitely bricked, I fear. Head to the nearest service centre.
I am from Kuwait ..
I purchased Samsung galaxy Note N7000 15 Days before
I have Installed King Droid ICS mania 2.1 later yesterday i updated to King droid ICS mania 3.0 and Samsung galaxy s3 Mod updated .. after that i restarted my NOTE but its not booting
i can go to Download mode and Recovery mode ..
even i can see the Install ZIP from SD card and all in CW ..when i Update it says
Can't Mount EMMC
I tried to Mount also But failure ..
I tried Stock rom of ICS official to Update Using ODIN 1.85 .. it stops at
<ID:0/008> factoryfs.img ..
I am worried I cant go for warranty Bcoz at Boot It says Binary count (5)
Please Help me Out

[Q] i9305t stuck on samsung logo

hello I have an i9305t was on official 4.1.1 upgraded to official 4.3 with odin .3.09 and it gets stuck on boot on the blue white pulsating Samsung logo. tried 4.1.2 fails tried 4.1.1 phone works fine, just cant upgrade to any new firmware at all. help would be great
vnholden said:
hello I have an i9305t was on official 4.1.1 upgraded to official 4.3 with odin .3.09 and it gets stuck on boot on the blue white pulsating Samsung logo. tried 4.1.2 fails tried 4.1.1 phone works fine, just cant upgrade to any new firmware at all. help would be great
Click to expand...
Click to collapse
To prevent you from being stuck onto the Samsung boot logo, you should wipe cache and wipe data from recovery after flashing the firmware. To do so follow these instructions.
1. Unplug the USB cable.
2. Shut down the phone.
3. Hold down the 'HOME' + 'VOLUME UP' buttons and press the 'POWER' button for about 5 seconds to enter Recovery Mode.
After entering recovery, you should see the options, to wipe cache and wipe data. wipe them. Hope you did a backup as you will use most of you files.
LucasBass said:
To prevent you from being stuck onto the Samsung boot logo, you should wipe cache and wipe data from recovery after flashing the firmware. To do so follow these instructions.
1. Unplug the USB cable.
2. Shut down the phone.
3. Hold down the 'HOME' + 'VOLUME UP' buttons and press the 'POWER' button for about 5 seconds to enter Recovery Mode.
After entering recovery, you should see the options, to wipe cache and wipe data. wipe them. Hope you did a backup as you will use most of you files.
Click to expand...
Click to collapse
thank for the reply I should of put that ive tried all that. doesn't work, just stays on that logo only way past it is to install 4.1.1.
Does your phone's IMEI (baseband) show up on 4.1.1 ?
dashing_9508 said:
Does your phone's IMEI (baseband) show up on 4.1.1 ?
Click to expand...
Click to collapse
yeah but only if I use perseus kernel. with out it I have no coverage aswell.
so has anyone got any ideas. much appreciated
vnholden said:
so has anyone got any ideas. much appreciated
Click to expand...
Click to collapse
I think you could try installing Stock 4.3 with Heimdall.
http://forum.xda-developers.com/showthread.php?t=1127419
viktorak said:
I think you could try installing Stock 4.3 with Heimdall.
http://forum.xda-developers.com/showthread.php?t=1127419
Click to expand...
Click to collapse
daaam was hoping that would of worked but no unfortunately. ready to throw this thing at the wall.
still having problems updating to any new firmware be it official or custom roms. nothing works, I tried cm11 all went well till the loading screen just cant get past that point. but 4.1.1 works without any problems.
I think you could try to use Triangle away,to reset flash counter and then use KIES recovery to reflash 4.1.1 stock.Then try to update to 4.1.2 or 4.3.
viktorak said:
I think you could try to use Triangle away,to reset flash counter and then use KIES recovery to reflash 4.1.1 stock.Then try to update to 4.1.2 or 4.3.
Click to expand...
Click to collapse
cheers mate ill give it a whirl but I don't think it will work. ill give you a big thanks anyway.
viktorak said:
I think you could try to use Triangle away,to reset flash counter and then use KIES recovery to reflash 4.1.1 stock.Then try to update to 4.1.2 or 4.3.
Click to expand...
Click to collapse
ok I tried what you recommended, but as I thought stuck on Samsung writing blue led light stays on. only one that worked was 4.1.1. I wonder if a modified binary or kernel is causing it. its how I got the phone so I don't no its history.
Well, let's try to flash true Mobile Odin pro a stock Samsung firmware.You need to be root.See if we're lucky.
Here you have the XDA Thread:http://forum.xda-developers.com/showthread.php?t=1347899
viktorak said:
Well, let's try to flash true Mobile Odin pro a stock Samsung firmware.You need to be root.See if we're lucky.
Here you have the XDA Thread:http://forum.xda-developers.com/showthread.php?t=1347899
Click to expand...
Click to collapse
thanks for trying to help I really appreciate it. as for mobile odin it will have to wait no funds on my card at moment. but I did manage to install a custom rom its 4.3 but I have no network coverage. in about settings unknown baseband.
this is the rom im using.
http://forum.xda-developers.com/gal...-amcha-rom-v5-00-simply-customizable-t2619670
perseus kernel stops the phone from not booting. that gives me my baseband. atleast ive got some where with it just need network to work now.
p.s sorry if im not making much sense but its beer drinking time for me. lol
You have to check the IMEI of your phone.If you have lost your IMEI see this thread:http://forum.xda-developers.com/gal...warning-guide-backup-restore-imei-nv-t1946915

[Q] Note 4 N910T stuck on boot screen

Hi,
My phone -Note 4 N910T- is stucked at bootscreen, and it can not to boot into recovery mode too. It is bootloop after upgrading by OTA from Kitkat 4.4.4 - N910TUVU1ANK4.
I tried to flash stock firmware( using both "N910TUVU1ANK4" and "N910TUVU1COD6" ), or full files stock firmware ( included PIT files),but it hasn't worked. I also tried to flash by Smatch Swich, everything seem OK but it can not fix.
I attached some photos of my problem for your reference.
Please help me.
Thanks,
You didn't mention if you tried using Kies?
DigitalChris602 said:
You didn't mention if you tried using Kies?
Click to expand...
Click to collapse
I tried using Kies too, but it did not work.:crying::crying::crying:
I was going to suggest the same thing. Try using Kies and go to Tools\Emergency firmware recovery and see if that works.
Can you get into download mode?
Karakoram2 said:
Can you get into download mode?
Click to expand...
Click to collapse
Yes, I can. One of my attached photos has shown as above. I tried to flash via ODIN or Smart Switch ( Kies 3), the program has shown OK but I still got the problem.
saclyvn said:
Yes, I can. One of my attached photos has shown as above. I tried to flash via ODIN or Smart Switch ( Kies 3), the program has shown OK but I still got the problem.
Click to expand...
Click to collapse
It is pretty hard to brick these phones. Just in case you have a bad file or something. Grab the zip and follow these instructions. I know that all these files in this zip are good so it is worth a shot.
Even if you know what you are doing, follow the instructions exactly, you may be overlooking something. It happens to everyone sometimes.
http://forum.xda-developers.com/showpost.php?p=56226823&postcount=2
After you odin whichever firmware you flashed, wait about 10 min or so on that boot screen that is stucked. Then pull the battery out. Go into stock recovery but power+home+vol up. Then select wipe data/reset. Reboot and it should boot just fine.
At least that's how i fixed my phone that stuck few times like what you going through.
mutantblack said:
After you odin whichever firmware you flashed, wait about 10 min or so on that boot screen that is stucked. Then pull the battery out. Go into stock recovery but power+home+vol up. Then select wipe data/reset. Reboot and it should boot just fine.
At least that's how i fixed my phone that stuck few times like what you going through.
Click to expand...
Click to collapse
The problem is my phone can not access to stock recovery or TWRP recovery. It just stuck at first bootscreen which is shown "Samsung Galaxy Note 4 powered by Android", then restart and stuck again. So that I can not wipe data or reset to fix.
saclyvn said:
The problem is my phone can not access to stock recovery or TWRP recovery. It just stuck at first bootscreen which is shown "Samsung Galaxy Note 4 powered by Android", then restart and stuck again. So that I can not wipe data or reset to fix.
Click to expand...
Click to collapse
Since you can still get into download mode, what happens if you flash TWRP through ODIN? Step 10 in the instructions I posted assuming it is still rooted or start at step 8 if not. Just to see if you can get recovery working again.
You are wasting time...start over, it's your best and quickest fix....
http://forum.xda-developers.com/not...sy-steps-stock-odin-n910tuvu1anih-cf-t2903733

Categories

Resources