Database Develop

firmware upgrade encountered an issue on my NOTE

guyz..i have a big problem right now..my NOte is on LA1..so to root it..i must
downgrade it first right?so i use the mobile odin and downgarde it to KK1...so after
following the procedure..after all been set up..i hit start...then i wait for about 1
hours..suddenly the box became red n said failed...i try to restart my phone then
there goes the message said firmware upgrade encounter an issue and ask me to
recovery mode using kies..how do i settle this problem guys...been searching for
hours how to overcome it..hope u guys can help me..me very newbies on
android..thanx in advance..

Press vol.down + home button + power. This will take you to download mode. Then flash a stock Rom using pc odin
Sent from my GT-N7000 using xda premium

thanx for the fast reply..thats what im doing now...past 1 hour already..my device got stuck at this since then.....
<ID:0/028> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DXLA1_N7000OLBKL2_N7000DXKL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> cache.img
<ID:0/028> NAND Write Start!!
<ID:0/028> factoryfs.img
whats wrong???

you need root so you have downgrade it with mobile odin???
You wr not rooted how you have used mobile odin?
Sent from my GT-N7000 using xda premium

Try a different stock Rom
Sent from my GT-N7000 using xda premium

dr.ketan...i've read the post that said newer kernel cant be root unless it's been downgrade...mine is la1..so i download the file of kk1 to downgrade my note..im not using mobile odin(my bad..wrongly describe)...im using pc odin

Then its ok
Read your first post, it is confusing
Anyway juat check your pc, have kies installed but not running in nackground, close any other pc sync sw running, disable firewall/antivirus if running
Put once device into recovert, clear cahe , delvic cache, wipe data
N retry, i believe problem is at your pc side.
Sent from my GT-N7000 using xda premium

right now my phone cant go into recovery mode...just download mode...its keeps showing the triangle icon(yellow) between phone n pc...rite now downloading another stock rom file...trying to do what indie suggested....
p/s-recovery mode=push volume up+home+power rite?i tried it...can't get in to recovery mode....T_T

Ya right way to get recovery
if not success just try another pc
Gudluck
Sent from my GT-N7000 using xda premium

please ...i have same porblem on my note ,,when upgrading using odin i have a massege FACTORYFS ,,and then HIDDEN and at las FAIL!! can u help me ..

@ brother,,,
flash to stock rom N7000XXKKA_N7000OXXKK5_AUT.zip
i got success flashing..

i have same problem in my note using pc odin hang in hidden option show, plz adv thnk for valuable advice urgent

Same problem
I having this same issue... Done what you did with no avail.. Just sent it in to samsung service centre.. They say will take a couple of days.. I lied, told them I woke up in the morning note couldn't switch on , took out battery and replace now ended this way.. Will wait for their call soon....

same problem here. tried to flash with a downgraded rom to root and now i get the yellow triangle.
tried flashing with pc odin and i get this
"<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000CPWKK3_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> zImage
<ID:0/010> NAND Write Start!!
<ID:0/010> boot.bin
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
any suggestions?

select USB debugging ON (setting - Application - development)
then connect to PC n Check your device manager(my computer - Rt click - property - device manager)
Is samsung device connected correctly( shouldn't have yellow mark)
refer this image
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If not connected correctly n having yellow mark, Reinstall drivers from here
If your OS is 32bit or 64bits
- connect your device to direct mainboard USB slot(back side pc) n without any extension cable
-Close any antivirus running
-close kies

hey ketan...i cant activate usb debugging as my phone wont boot anything.. just get the samsung galaxy note writting with yellow triangle.
ill try installing drivers again
---------- Post added at 06:21 PM ---------- Previous post was at 06:19 PM ----------
ive managed to install CF-Root-SGN_XX_SER_LA6-v5.0-CWM5 as my phone is LA6.. then i go to install a rom and it fails!
---------- Post added at 06:24 PM ---------- Previous post was at 06:21 PM ----------
yes device is fine in device manager "Samsung Mobile USB CDC Composite Device" No yellow triangles!

Have you try to install any Custom Kernel (CF root or any) with PC Odin?? Otherwise yellow triangle shoudn't appear
Go to recovery (vol up +Home+ power), wipe cache
If still errr wipe data
then restart
Still error reflash

origionaly i tried to downgrade the rom so i could root it. i ried what you said but i cant seem to get any option to wipe data and clear cache!

Press vol up + home + power
When screen appear, release power n keep holding rest of two buttons
You will enter in recovery n able to see wipe cache n wipe data option
Sent from my GT-N7000 using xda premium

cant seem to get it to show up, i dont have CWM installed otherwise i would use that to do it.! any suggestions

[Q] Please help me - ICS TO GB - DO NOT WANT TO BRICKS :(

I know that this is probably another post in a series of desperate to get back to ICS for GB, but please understand me, I did not want to get my phone is a brick
I used the CheckROM NoteHD ™ V6. I tried to go to Criskelo LPY V3's ICS ICS. I restarted my phone into recovery and I flash: AbyssNotekernel42RedTouchCustomLogo.zip
Then I reboot and recovery (the recovery RedTouch) I did factory reset, wipe and wipe cahce Dalvik cache and then and flash Criskelo LPY V3's ICS ICS. When the flash ended (I did not have any information about errors) successfully I restarted my phone. My phone Restarted a few times and finally started to Criskelo's ICS ICS LPY V3.
But I wanted to return to the previous rom. Perhaps I did wrong, but I restarted my phone into recovery and I tried to flash again: AbyssNotekernel42RedTouchCustomLogo.zip (I thought that this way I can upload my copy of the rom GB) .... but after the approval of the progress bar stops, and after about two minutes, the phone reboots again it's ICS ICS Criskelo LPY V3
Just notice another problem, not sure if it is when I tried binary updating SU.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Screen was made by another user, but for me it is exactly the same.
Everything indicates that I have root - titanium works and I can copy and delete any file in the system
Now the question:
How should I go back to GB (whether it is better not to do it?). Please help me what should I do step by step?

Don't panic mate!
Go into Recovery
Flash abyss 4.2 or Franco 10
FULL WIPE (factory reset,cache,davnik cache)
Restore backup or even better Flash a clean GB ROM
Edit: of course you can use PC Odin in download mode and flash a pre-rooted GB From.
Sent from my GT-N7000 using Tapatalk 2

sotiris20 said:
Don't panic mate!
Go into Recovery
Flash abyss 4.2 or Franco 10
FULL WIPE (factory reset,cache,davnik cache)
Restore backup or even better Flash a clean GB ROM
Edit: of course you can use PC Odin in download mode and flash a pre-rooted GB From.
Click to expand...
Click to collapse
thanks man,
but if I restarted my phone into recovery and I tried to flash again: AbyssNotekernel42RedTouchCustomLogo.zip after the approval of the progress bar stops, and after about two minutes, the phone reboots again it's ICS ICS Criskelo LPY V3.... maybe it is wrong way

kamilloo83 said:
thanks man,
but if I restarted my phone into recovery and I tried to flash again: AbyssNotekernel42RedTouchCustomLogo.zip after the approval of the progress bar stops, and after about two minutes, the phone reboots again it's ICS ICS Criskelo LPY V3.... maybe it is wrong way
Click to expand...
Click to collapse
Its not the "wrong way".Flash a clean Rom now,not your backup. Maybe your backup file is corrupted. If you want try Pc-Odin as I said before. Your choice...
Anyway, hope you'll figure it out.
Sent from my GT-N7000 using Tapatalk 2

OK I trust you
Will it be ok as I flash in PC ODIN from:
http://forum.xda-developers.com/showthread.php?t=1424997
it:
Older ROMs (Directly Rootable)
N7000XXKKA ------ 2.3.6 2011 November------- N7000PLSKK1 -----------------Poland (PLUS) ----------------------- Download
and next I'll be root, and I will be able to upload the recovery CheckROM NoteHD ™ V6

kamilloo83 said:
thanks man,
but if I restarted my phone into recovery and I tried to flash again: AbyssNotekernel42RedTouchCustomLogo.zip after the approval of the progress bar stops, and after about two minutes, the phone reboots again it's ICS ICS Criskelo LPY V3.... maybe it is wrong way
Click to expand...
Click to collapse
After flashing the AbyssNotekernel42RedTouchCustomLogo.zip you rebooting the phone or rebooting the recovery ?

abhisahara said:
After flashing the AbyssNotekernel42RedTouchCustomLogo.zip you rebooting the phone or rebooting the recovery ?
Click to expand...
Click to collapse
not because the flash: AbyssNotekernel42RedTouchCustomLogo.zip is not succesfully -> my phone freezes during this operation, and then restarts
addition, one user wrote:
Entropy512 said:
Don't flash a GB kernel from recovery! Odin/Heimdall it! If you are unable to flash kernels with Odin/Heimdall, you may be suffering from eMMC damage.
Click to expand...
Click to collapse

I sincerely fear you may have the dreaded Superbrick mate. All the symptoms are there.

He can still ODIN, right? I haven't read where he said he can't access download mode. He was just trying to do stuff in recovery. Can we confirm you can not access download mode either?

chasmodo said:
I sincerely fear you may have the dreaded Superbrick mate. All the symptoms are there.
Click to expand...
Click to collapse
I am afraid that most
What do you think should I do to try to flash with the hope of GB?

andreww88 said:
He can still ODIN, right? I haven't read where he said he can't access download mode. He was just trying to do stuff in recovery. Can we confirm you can not access download mode either?
Click to expand...
Click to collapse
you're right, I have not written anywhere that I can not enter download mode .. but have not tried ... charge the phone at the moment - in the evening I'll be ready ....
or should I do as I wrote above - this example ROM, and my description is OK?

kamilloo83 said:
you're right, I have not written anywhere that I can not enter download mode .. but have not tried ... charge the phone at the moment - in the evening I'll be ready ....
or should I do as I wrote above - this example ROM, and my description is OK?
Click to expand...
Click to collapse
Okay cool, that's fairly good news because if you CAN enter download mode you are not bricked and you can ODIN a pre-rooted GB rom or a stock GB rom. If your phone will charge, let it charge up and then ODIN away.

andreww88 said:
Okay cool, that's fairly good news because if you CAN enter download mode you are not bricked and you can ODIN a pre-rooted GB rom or a stock GB rom. If your phone will charge, let it charge up and then ODIN away.
Click to expand...
Click to collapse
ufff... I hope...
ask again:
Will it be ok as I flash in PC ODIN from:
http://forum.xda-developers.com/show....php?t=1424997
it:
Older ROMs (Directly Rootable)
N7000XXKKA ------ 2.3.6 2011 November------- N7000PLSKK1 -----------------Poland (PLUS) ----------------------- Download
and next I'll be root, and I will be able to upload the recovery CheckROM NoteHD ™ V6 ??? ....

Yes, that is thread you need to follow.
You can root by following Dr.Ketan's steps too.

OPERATION FAIL:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000OXXKK6_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WHAT IS WRONG?

kamilloo83 said:
OPERATION FAIL:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKKA_N7000OXXKK6_N7000XXKK5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WHAT IS WRONG?
Click to expand...
Click to collapse
Not sure. Can you try another ROM file on that thread? That doesn't look promising, but maybe someone else can help that knows more.

andreww88 said:
Not sure. Can you try another ROM file on that thread? That doesn't look promising, but maybe someone else can help that knows more.
Click to expand...
Click to collapse
I must download anotheher ROM... one moment...

kamilloo83 said:
I must download anotheher ROM... one moment...
Click to expand...
Click to collapse
Maybe even try LPF ICS?
It might just have been a bad download, but the MD5 checked good it looks like so I don't know. I'd like someone else to say something to try to help.

Try repartitioning the device. To do so use simply set the right pit file in odin.

rupalazzi said:
Try repartitioning the device. To do so use simply set the right pit file in odin.
Click to expand...
Click to collapse
can I use it with ROM: N7000XXKKA_N7000OXXKK6_N7000XXKK5_HOME.tar.md5
together in PC ODIN?

Galaxy Ace will not go into download mode, Stays stuck on Dowloading scree

Hello Gents,
Looked around could no find an explanation for this so made this thread. Trying to update my Galaxy Ace to 2.3.6(official Firmware, India) using ODIN for PC, but when I try to go into download mode(Vol down + Home + power) it goes to the screen that says 'Downloading.....' and stays there, have tried waiting for 10-15 mins but nothing will not move forward. Eventually I have to remove the battery and just let it boot to into the normal mode(works fine).
Also the update does not come up on the OTA notification, is OTA not supported by Ace?
Any Ideas?
Thanks in Advance

something like this?
islam_ashraf said:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
!
Click to expand...
Click to collapse
yes that is download mode.

superdunkaroos said:
Hello Gents,
Looked around could no find an explanation for this so made this thread. Trying to update my Galaxy Ace to 2.3.6(official Firmware, India) using ODIN for PC, but when I try to go into download mode(Vol down + Home + power) it goes to the screen that says 'Downloading.....' and stays there, have tried waiting for 10-15 mins but nothing will not move forward. Eventually I have to remove the battery and just let it boot to into the normal mode(works fine).
Also the update does not come up on the OTA notification, is OTA not supported by Ace?
Any Ideas?
Thanks in Advance
Click to expand...
Click to collapse
This is the download mode, there is no OTA updates for ace as far as i know
check this post for how to flash new firmware
http://forum.xda-developers.com/showthread.php?t=1034145

This is the download mode. Start flashing, there aren't any problems

Ahhh, thats what I thought earlier, I thought it wasn't in the mode because Odin3 1.85 is stuck at this step:
BTW the first square turns yellow in Odin.
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830DDKQ8_S5830ODDKQ7_S5830DDKQ8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
any Ideas? Even if I disconnect and restart it starts normally, although the firmware isn't updated.

superdunkaroos said:
Ahhh, thats what I thought earlier, I thought it wasn't in the mode because Odin3 1.85 is stuck at this step:
BTW the first square turns yellow in Odin.
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830DDKQ8_S5830ODDKQ7_S5830DDKQ8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
any Ideas? Even if I disconnect and restart it starts normally, although the firmware isn't updated.
Click to expand...
Click to collapse
Odin 1.85 thats for S5830i You're supposed to use 4.38 if you have the original Ace S5830
OTA is supported but you just need to enable OTA in About phone -> Software Update and register an samsung user account

Georges2251 said:
This is the download mode. Start flashing, there aren't any problems
Click to expand...
Click to collapse
+1

Galaxy ace has OTA
I believe it was Called FOTA i used it when i was on official xwkpo 2.3.3 to update to 2.3.6
Sent from my GT-S5830 using xda premium

CoolCatGetHome said:
Galaxy ace has OTA
I believe it was Called FOTA i used it when i was on official xwkpo 2.3.3 to update to 2.3.6
Sent from my GT-S5830 using xda premium
Click to expand...
Click to collapse
I thought that for OTA update, you have to do it from settings-> about phone-> update
i wasnt aware that you do it from the download mode

i have a problem
odin 4.38 i use to flashed and it pass but my s3850i still stuck on samsung logo what should i do ??
please help me ..... thanks....

-Put- said:
odin 4.38 i use to flashed and it pass but my s3850i still stuck on samsung logo what should i do ??
please help me ..... thanks....
Click to expand...
Click to collapse
reboot via recovery (home + power button when your device is power off until you enter into recovery mode) and wipe data/factory reset and cache

Tipp
My Tipp is.
Connect the USB Cable when on the Screen you can read "downloading"
Before connect the USB Cable NOT!
Grettings
BrandY2001

[TUT]Rooting the mini 2 S6500D (Super noob friendy)(video added)

Hi Everyone
VIDEO:
https://www.youtube.com/watch?v=94vIeinaddQ
i will show you how to root the Samsung galaxy mini 2 S6500D
and i will move step by step in this tut as i will Root my device as well, I've Unrooted it so i can show you every step
ok, so first of all there is some files that you need to download first:
1- you must have the ADB drivers for your phone and you do that by downloading Samsung kies
just google it and you will find it
2- download this rar file here
Ok so lets get started
- After Downloading Samsung Kies connect your Phone to the pc so the Kies can detect it and install its drivers.
- grab your phone
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
( its really advisable to be fully charged, or at least 90% or so ) things can get really bad if the phone turns off while rooting :silly:
- Trun off the phone,Boot your phone in ( Download mode ) you can do that by pressing Vol (down) and Home and power key all at once, after that you should get to this screen:
just press the volume up to ignore the warning To proceed.
Then connect your phone to the pc and open Odin3 v1.85.exe from the rar(mini2.rar) that you downloaded and extracted
then press the PDA button and choose the other file called ( clockworkmod-5.0.2.8.tar.md5 )
ok, before we continue you should take care of something
if you get Exactly this screen, then you did something wrong
as you see in the rec circle Odin did NOT detect your phone
-its either not connected probably or its drivers is not installed
so make sure you check both of these things
now if you get THIS screen with Oding detecting your phone then you are ready to go
press the PDA button and load the file called ( clockworkmod-5.0.2.8.tar.md5 )
then press start,If you see pass with green background make sure you did it right
after that CLOSE, you must COLSE odin, just exit it.
Now turn off your phone again and boot it in ( REcovery mode ) you can do this by pressing both of the volume buttons and the home and power key, so basically you just press all the buttons at the same time.
as you see it will say GT7500 but its ok, :highfive:
You should get this screen
remember your phone is still connected to the pc the whole process
Now open the other file
AGAIN, if you get this kind of error ( device not found )
Then you you probably did the same thing and proceed without making sure of finishing the prev.step.
But if you did it correctly, you should see this:
it MIGHT (probably will) fail the first time, just exit and run the file again to make sure.
Then you are ready to go
now you will be automatically on the first option ( reboot system now ) just press the home key and the phone will reboot
open the app menu and you should see ( super user ) installed on your phone
to make sure you are rooted just go to the google store and search Titanum backup
install it and you will see it Require the super user request to proceed,
or you can just search for any root checker app as well
https://play.google.com/store/apps/details?id=burrows.apps.rootchecker
many thanks to the people who find out the way to root the phone :highfive:
i just LOOOVE to create Tutorials :good: :victory:
if you have any questions feel free to ask in the comments )
​

Good tutorial.
I'm glad that we have a dev forum for mini II. First stiky posts must be: how to root, how to install a custom ROM, how to go back to stock.

help! i rooted and then installed rom toolbox and now i accidentaly clicked reboot to recovery in rom toolbox. and now i always boot to recovery please help

rhisendark said:
help! i rooted and then installed rom toolbox and now i accidentaly clicked reboot to recovery in rom toolbox. and now i always boot to recovery please help
Click to expand...
Click to collapse
just flash back to stock rom via odin
you can find stock rom at sammobile.com
and remember its always best to make backup before installing roms.
Sent from my GT-S6500D using xda app-developers app

joey_W said:
just flash back to stock rom via odin
you can find stock rom at sammobile.com
and remember its always best to make backup before installing roms.
Sent from my GT-S6500D using xda app-developers app
Click to expand...
Click to collapse
lol i did same thing nearly took nani back up with rom toolbox boot me to cwm to get back ups.. well it did good but it doesnt boot normaly to system after back up keep geting me in recovery mode and cant get in download mode to flash a firmware to fix it need help |! any advice, walktho... will be cool. thx..
--
i just took it in DL mode looks everything going good right now installing S6500XXLD2 to jump in peters mod.
--
had problem whil flashing XXLD2 odin gave error like this phone still at download mode and progress stop arond %95ish. now i need a serious help ..
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6500XXLD2_S6500XXLD2_S6500DBTLD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img.ext4
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> fat.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
phone says in download mode Secure check fail : ID 0xc
--
phone still on at download mode stuck at loading screen with that secure check fail thingy.. i ll keep it up dont mess up any thing till someone gives a hand

hayta77 said:
lol i did same thing nearly took nani back up with rom toolbox boot me to cwm to get back ups.. well it did good but it doesnt boot normaly to system after back up keep geting me in recovery mode and cant get in download mode to flash a firmware to fix it need help |! any advice, walktho... will be cool. thx..
--
i just took it in DL mode looks everything going good right now installing S6500XXLD2 to jump in peters mod.
--
had problem whil flashing XXLD2 odin gave error like this phone still at download mode and progress stop arond %95ish. now i need a serious help ..
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6500XXLD2_S6500XXLD2_S6500DBTLD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img.ext4
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> fat.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
phone says in download mode Secure check fail : ID 0xc
--
phone still on at download mode stuck at loading screen with that secure check fail thingy.. i ll keep it up dont mess up any thing till someone gives a hand
Click to expand...
Click to collapse
My meant your problem from cable usb or port usb you pc try orther usb or orther pc.. CMIIW
Sory for my bad english
Sent from my GT-S6500D using xda app-developers app

..

It's working great
But how to revert back to original recovery??
​

Just flash a stock rom.
Wysyłane z mojego GT-S6500D za pomocą Tapatalk 2

Thanks for this great tutorial :laugh:

I've made a Video

S6500L
Hello am asking around with no answers but whats the difference with the S6500L and the other models and will this rooting process and the other roms work on it? Thanks in advance

Thx for the TUT, 2 quick question.
Do you have a list with apps can uninstalled safe?, or know the link in the forum with this info?

It will increase the bin counter(number) after installing CWM and rooting?

nikobadboy said:
It will increase the bin counter(number) after installing CWM and rooting?
Click to expand...
Click to collapse
yes after installing CWM using odin

Thanks , this vid help me a lot couse this is my first android phone
Sent from my GT-S6500D using xda app-developers app

I cant find Odin3 v1.85.exe in mini2 rar are (clockworkmod-5.0.2.8.tar.md5 and RootMe) and in Root me are (run me and a folder named "files")
Ok I google it and I downloadit!
Now I can not boot in Recovery mode, I try and try but it boots normaly and not in Recovery.
And again I din't disconect my USB cable before I try to boot in Recovery, so it didn't, but with the cable disconectid it was all good and now my phone is root.
Everyone please see the video.
THANX MAN!!!

nice work
Sent from my Optimus Net using xda app-developers app

How to Unroot ?
Hi , it is great rooting tutorial so thanks
But i really want to know how did you unroot your phone
Because my friend want to it with his phone so pleas help

thx m8 good tutorial for first time users. :good::highfive:
Regards
MB from Holland​

Galaxy S I9000 won't boot, no recovery, only download mode available

Hello folks,
First I must say that before I post this thread I searched for days to find out a solution, I tried everything I know about to fix my issue without luck.
What happened:
I was on cyanogenmod 10.1.2 (4.2.2) with semaphore kernel 3.0 everything running flawless for month nothing much to say.
I dismounted my external SDcard 16go to switch for another one 32go while the phone was on (I did this multiples times before without issues) but when I mounted it back I had a "searching for error" notification so I waited for a time and my phone gone off alone.
I power it on back but my screen just show "Galaxy S I9000" logo and nothing else happen. So I waited for a time, removed the battery, and power it on again but no luck, my phone seems to have a bootloop I thought.
I decided to flash back to stock rom in order to fix it (I did this before when I got bootloop with froyo, gingerbread, ics ... good old day )
My phone is an international I9000 PRO (belgium)
I flashed a XXJVU stock rom with repartition on PIT 512(because of different partition format from cyanogenmod) with ODIN, everything is running fine from ODIN, no errors, the phone reboot but still no luck : stuck with the Galaxy S I9000 screen, nothing else happen.
I can get download mode but no recovery mode, so I tried to flash a semaphore ICS kernel: no luck again, no recovery available.
I started to get worried and tried everything possible from http://forum.xda-developers.com/showthread.php?p=29331775#post29331775
Still no luck my phone is stuck to this Galaxy S I9000 screen. I can't get recovery mode, only download mode.
I flashed another stock rom :GT_I9000_XWJW5_XDJV1_OXXJVC_Sbl because of the sbl as I thought my boot partition was screwed but still no luck, no boot past the Galaxy S I9000 screen.
I just have the download mode available that is all.
My battery is at 100%
ODIN flash without any errors
What can I do in order to fix it? and if I can't, can I try to save my internal SDcard documents (photos, pdf, doc ...)? Can I mount my internal SDcard from download mode to fix this loop? or to save my important documents?
I am sorry for my basic english, I thank you in advance to anyone who try to help me.

Negatho said:
H
I dismounted my external SDcard 16go to switch for another one 32go while the phone was on (I did this multiples times before without issues) but when I mounted it back I had a "searching for error" notification so I waited for a time and my phone gone off alone. .
Click to expand...
Click to collapse
Remove your External SD card and try, could be wrong format, as it needs to be formatted in phone first.
Check this out!You , YES! you are an " Android ". Not your phone but U.
You Must watch this documentary concerning your privacy Terms & Conditions we had agreed to, by using a PC or Smartphone
How to say Thank you? If you find any post helpful on XDA, please click on the Thanks button
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you are using XDA App or Tapatalk, long press on the post and select :good: Thanks Its easier to give "Feedback" in this manner than make an additional post.​

I've already did that in the first time.
Now I retired everything from the phone (sim card and SDcard) to flash a stock rom in order to fix this bootloop but still no luck.
I couldn't pass that Galaxy S I9000 screen, nothing happen.
I don't have any recovery mode available now, only download mode.
When I flash a stock rom (I tried JVU, JW5 full stock) ODIN says nothing wrong, everything seems to go fine, but the phone is stuck at start screen.

Negatho said:
I've already did that in the first time.
Now I retired everything from the phone (sim card and SDcard) to flash a stock rom in order to fix this bootloop but still no luck.
I couldn't pass that Galaxy S I9000 screen, nothing happen.
I don't have any recovery mode available now, only download mode.
When I flash a stock rom (I tried JVU, JW5 full stock) ODIN says nothing wrong, everything seems to go fine, but the phone is stuck at start screen.
Click to expand...
Click to collapse
follow this guide to flash the JVU with PIT
Check this out!You , YES! you are an " Android ". Not your phone but U.
You Must watch this documentary concerning your privacy Terms & Conditions we had agreed to, by using a PC or Smartphone
How to say Thank you? If you find any post helpful on XDA, please click on the Thanks button
If you are using XDA App or Tapatalk, long press on the post and select :good: Thanks Its easier to give "Feedback" in this manner than make an additional post.​

I did follow your guide (pretty nice guide by the way)
Here is my ODIN output:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 is valid.
<OSM> GT-I9000-CSC-MULTI-OXAJVU.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> Sbl.bin
<ID:0/003> param.lfs
<ID:0/003> factoryfs.rfs
<ID:0/003> dbdata.rfs
<ID:0/003> cache.rfs
<ID:0/003> zImage
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response form LOKE
<ID:0/003> cache.rfs
<ID:0/003> dbdata.rfs
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
The phone reboot but still stuck at Galaxy S GT-I9000 screen. I still don't have a recovery mode, only download mode available.
I couldn't flash a CF-Root kernel because the first flash did not complete the first run (I guess) and even if I flash a CF-Root kernel (jvu, I tried it before) I still don't have a recovery mode.
I feel so sad, maybe my internal SD is screwed ... I had this phone since 3 years, did alot of flash before, got it bricked, saved it multiple times without any issue, strong device but now I think it's done, the end
Now, if you know a way to read the internal SD without recovery mode you are a god
I think I will give up.

Negatho said:
I feel so sad, maybe my internal SD is screwed ... .
Click to expand...
Click to collapse
well, you can always use external SD card, when your internal SD card is fried...just read this and related links in it , first to digest the issue and try when you are SURE how you would proceed, the easiest is having a single SD card partitioned into two to act like its the internal and external.
The problem here seems you had made a swap, and that needs to be undone
Check this out!You , YES! you are an " Android ". Not your phone but U.
You Must watch this documentary concerning your privacy Terms & Conditions we had agreed to, by using a PC or Smartphone
How to say Thank you? If you find any post helpful on XDA, please click on the Thanks button
If you are using XDA App or Tapatalk, long press on the post and select :good: Thanks Its easier to give "Feedback" in this manner than make an additional post.​