Battery - Galaxy S I9000 Q&A, Help & Troubleshooting

I some up this morning and saw my battery was at 88%, it has bin on charge all night how can I fox this so it charges to 100%?
Sent from my GT-I9000 running remICS-UX using XDA premium

"some up"? Ok... go to CWM->Advanced->Wipe Battery Stats ... if doesn't work, do a full wipe or reflash ROM, you are using...

Woke* auto correct lol, and o do this after every ROM flash and this wouldn't affect that anyway, its not done it before, only to 98% or something but I read that it does this it will reach 100% the stop charging to preserve the battery, but dropping to 88% is a bit extreme I think I'm losing like an hour of battery life
Sent from my GT-I9000 running remICS-UX using XDA premium

calum96 said:
Woke* auto correct lol, and o do this after every ROM flash and this wouldn't affect that anyway, its not done it before, only to 98% or something but I read that it does this it will reach 100% the stop charging to preserve the battery, but dropping to 88% is a bit extreme I think I'm losing like an hour of battery life
Sent from my GT-I9000 running remICS-UX using XDA premium
Click to expand...
Click to collapse
This is a calibration problem caused exactly by you wiping your battery stats, you need to leave them alone and after each flash do a full empty to full charge cycle so the stats can provide proper calibration statistics, I have never wiped battery stats in 2 years of owning my phone

I always do this after a wipe, wait till fully charged>wipe stats>discharge fully>recharge fully
Sent from my GT-I9000 running remICS-UX using XDA premium

Ok, I know the point you are making but I personally think it does more harm than good.... Does it drop straight down the moment you remove the charger?

I don't know if it might be a battery problem, or if the CM9 Nightly build I'm currently on holds a charge really well, but sometimes I charge my phone up to 100%, then after about 30 minutes of continuous, non-stop usage, the battery is still at 99%.
Is this odd behaviour or is it normal?

slaphead20 said:
Ok, I know the point you are making but I personally think it does more harm than good.... Does it drop straight down the moment you remove the charger?
Click to expand...
Click to collapse
No it only charges to 88% unless I remove charger then plug it back in again then it will charge to 100%, I think its because the phone charges to 100% then drains then charges, but I think its failing to start charging once it drops to a certain limit (say 10%) so normally it would charge to 100% drop to 90% then charge to 100% so it doesn't damage the battery, but as I said I think its failing to start charging again so it just keeps falling... I need a fix for this? And yes it is a cm9 base
Sent from my GT-I9000 running remICS-UX using XDA premium

Try battery calibration from the play store
Sent from my GT-I9000 using xda app-developers app

amerkiller1995 said:
Try battery calibration from the play store
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=28544220
Sent from my GT-I9000 running remICS-UX using XDA premium

slaphead20 said:
This is a calibration problem caused exactly by you wiping your battery stats, you need to leave them alone and after each flash do a full empty to full charge cycle so the stats can provide proper calibration statistics, I have never wiped battery stats in 2 years of owning my phone
Click to expand...
Click to collapse
I've always been wondering: is it possible to "damage" the battery or lose some of it's juice by doing wipe battery stats to many times?

solved
calum96 said:
http://forum.xda-developers.com/showthread.php?p=28544220
Sent from my GT-I9000 running remICS-UX using XDA premium
Click to expand...
Click to collapse
ooooh thanks that worked for me:laugh:

battery quick use up
my battery up to 1850 map... y the battery still quick use up while i ady is ICS...

Related

Can I flash with 60 percent battery?

Can I flash a new ROM with 60 percent battery? I see where most ROM'S recommend flashing with a full battery. Does this affect anything like how much charge the phone thinks the battery has? Or are there other reasons to flash with a full battery?
Sent from my Captivate running Firefly 2.3
redger725 said:
Can I flash a new ROM with 60 percent battery? I see where most ROM'S recommend flashing with a full battery. Does this affect anything like how much charge the phone thinks the battery has? Or are there other reasons to flash with a full battery?
Sent from my Captivate running Firefly 2.3
Click to expand...
Click to collapse
It doesn't matter. I flashed at 5% once. The only thing you have to do is recalibrate your battery after.
Sent from my SGH-I897 using XDA App
Wouldn't it be a risk if your phone died somehow during odin
Sent from my SAMSUNG-SGH-I897 using XDA App
rjblack11 said:
Wouldn't it be a risk if your phone died somehow during odin
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
That would be a big problem
I tend to always flash at 100%. Just to avoid any issues. But you can flash at 60% if you really wanted to. Just do a calibration
Do it with full battery . Calibrating takes ages
Galaxy S 16gb Darkys 9.3 beta
rjblack11 said:
Wouldn't it be a risk if your phone died somehow during odin
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Trying to be a smart aleck, not confrontational...
If you are using odin, by definition the phone is plugged in to a USB power source. I suspect you couldn't drain the battery in that circumstance - maybe if you were plugged in, playing a video while serving up Mobile AP. But not when the screen is doing nothing but saying it's in download mode.
I have flashed through cwm with under 50%
rjblack11 said:
Wouldn't it be a risk if your phone died somehow during odin
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
That's assuming every one uses odin
I just clear data and cache and flash the new rom. But I charge up to 100% so the battery reads fine.
Soccer_Dad said:
Trying to be a smart aleck, not confrontational...
If you are using odin, by definition the phone is plugged in to a USB power source. I suspect you couldn't drain the battery in that circumstance - maybe if you were plugged in, playing a video while serving up Mobile AP. But not when the screen is doing nothing but saying it's in download mode.
Click to expand...
Click to collapse
Yeah thats why I said "somehow". I thought about your point while posting though and it makes plenty of sense and im pretty sure you can charge a phone no matter what state it is in (soft brick, hard brick, waterlogged ha)
Sent from my SAMSUNG-SGH-I897 using XDA App
Yea
I've flashed in the range of 50 - 100%, never had a problem
like others said you just have to recalibrate your battery after.
I probably wouldn't go less than 50% though just to be safe.
It would probably be best to flash on a full battery, but I don't think its necessary. Just recalibrate and wipe battery stats and you should be fine.
Yes you can. May need to calibrate
Sent from my Captivate using XDA Premium App

Copying battery stats file?

Would it work to just copy the battery stats file to another rom so u don't have to re calibrate everytime u install one or would that be a bad idea
Sent from my DROID3 using XDA App
prsterero said:
Would it work to just copy the battery stats file to another rom so u don't have to re calibrate everytime u install one or would that be a bad idea
Sent from my DROID3 using XDA App
Click to expand...
Click to collapse
You don't need to calibrate, just charge it full. Battery stats are automatically wiped when you unplug with a full charge.
Sent from my XT860 using xda premium
Endoroid said:
You don't need to calibrate, just charge it full. Battery stats are automatically wiped when you unplug with a full charge.
Sent from my XT860 using xda premium
Click to expand...
Click to collapse
Well the new 3500 milliamp battery I got says to fully discharge and charge 4-5 times to get the most out of ur battery. Or is that just for when u first get it
Sent from my DROID3 using XDA App
prsterero said:
Well the new 3500 milliamp battery I got says to fully discharge and charge 4-5 times to get the most out of ur battery. Or is that just for when u first get it
Sent from my DROID3 using XDA App
Click to expand...
Click to collapse
Just when you first get it. Its a "break in" for batteries.
Sent from my XT862 using XDA App
Although I believe that its good to do a full discharge and charge every so often.
Sent from my XT860 using xda premium
Alright that's what I thought. Although while discharging my phone froze up and rebooted so I think ill have to recalibrate again lol
Sent from my DROID3 using XDA App
prsterero said:
Alright that's what I thought. Although while discharging my phone froze up and rebooted so I think ill have to recalibrate again lol
Sent from my DROID3 using XDA App
Click to expand...
Click to collapse
It shouldn't affect battery. I've tested it myself, battery life before and after calibration is no different. This calibration myth was debunked by a google framework engineer.
Sent from my XT860 using xda premium
ya I read a short thing on that. Kinda odd though. Seems like sometimes u could get a worse battery life some days compared to others. But it also seems like a good idea since u don't have to calibrate every time u do something.
Sent from my DROID3 using XDA App
The calibration has nothing to do with the battery life, it just gives a more "exact" reading of the battery level.. I miscalibrated my battery once, and it was at 1% for about 3 hours, then finally died..
Sent from my XT862 using XDA App
ChaoticWeaponry said:
The calibration has nothing to do with the battery life, it just gives a more "exact" reading of the battery level.. I miscalibrated my battery once, and it was at 1% for about 3 hours, then finally died..
Sent from my XT862 using XDA App
Click to expand...
Click to collapse
Ya that happened to me once. Now I just make a point of being able to fully charge anytime I flash a rom.
Sent from my XT860 using xda premium
I have now been convinced that there is no reason to calibrate your battery at anytime. Google engineer pretty much put it to rest and since then I have flashed repeatedly and all that changes is the ROM , sometimes battery is bad and other times its great. CM9 is best so far. Until we get new kernals our battery won't ever be great.
Sent from my XT862 using XDA App
atlantanetworkguy said:
I have now been convinced that there is no reason to calibrate your battery at anytime. Google engineer pretty much put it to rest and since then I have flashed repeatedly and all that changes is the ROM , sometimes battery is bad and other times its great. CM9 is best so far. Until we get new kernals our battery won't ever be great.
Sent from my XT862 using XDA App
Click to expand...
Click to collapse
Ya reading through the comments it seems batterystats.bin has nothing to do with the displayed battery level, but rather just what is using the battery. The displayed battery level comes from kernel level
Sent from my XT860 using xda premium
ChaoticWeaponry said:
The calibration has nothing to do with the battery life, it just gives a more "exact" reading of the battery level.. I miscalibrated my battery once, and it was at 1% for about 3 hours, then finally died..
Sent from my XT862 using XDA App
Click to expand...
Click to collapse
Same, although not for 3 hours but 15min heavy load (720p mkv). Which normally kills 10% battery.
After calibrate it never happened again and died right after 1%

Battery drain after restarting note on 4.0.4

My battery has been sluggish right after updating 4.0.4. Right after restarting my device, i left only 20% of battery instead of 90% before restarting. Im getting sick n tired of samsung. Thers always a problem after software update. Im wondering wether they ever tested their software before releasing it to consumer. LOUSY
Sent from my GT-N7000 using xda premium
safuan7822 said:
My battery has been sluggish right after updating 4.0.4. Right after restarting my device, i left only 20% of battery instead of 90% before restarting. Im getting sick n tired of samsung. Thers always a problem after software update. Im wondering wether they ever tested their software before releasing it to consumer. LOUSY
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Calibrate your battery.
Let it empty untill blackout. Take out battery for 2 min then put it back again, and charge it to full, do not push the on button while charging.
My suggestion is to install and SPYCPU podesiš processor clock so you would not spend the battery more than they need. We also have a large selection governo, naćićeš best balance of performance and battery life.
Thanks jonpaslim! i will try to do that and will update the results
Sent from my GT-N7000 using xda premium
Battery life better
safuan7822 said:
My battery has been sluggish right after updating 4.0.4. Right after restarting my device, i left only 20% of battery instead of 90% before restarting. Im getting sick n tired of samsung. Thers always a problem after software update. Im wondering wether they ever tested their software before releasing it to consumer. LOUSY
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
After i updated to 4.0.4 baterry life was significantly better. try using carat, it works
I found this on a site somewheres ......
1.turn on aeroplane mode
2.turn off device
3.take out battery for 10 seconds
4.turn on device
5.wait for everything to load
6.turn off aeroplane mode
Hi dickwyn, thanks for your reply.
Done with the installation. But it seems not doing anything.. As in 'nothing to report' is that normal?
Sent from my GT-N7000 using xda premium
safuan7822 said:
Hi dickwyn, thanks for your reply.
Done with the installation. But it seems not doing anything.. As in 'nothing to report' is that normal?
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Install CpuSpy from playstore.
Check if ur device goes in deep sleep mode.. If not then follow these steps.. :-
1.turn on aeroplane mode
2.turn off device
3.take out battery for 10 seconds
4.turn on device
5.wait for everything to load
6.turn off aeroplane mode
Thanks.
Done everything. But it messed up with my time and date. It went all the way back to year 2000.. Is that normal?
Sent from my GT-N7000 using xda premium
safuan7822 said:
Thanks.
Done everything. But it messed up with my time and date. It went all the way back to year 2000.. Is that normal?
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Settings>Time &Date>Use Network Provider Values..
which rom are you on?
Sent from my GT-N7000 using Tapatalk 2
Baz77,
Im not sure which rom tho. Well i hv totally no idea. Its a stndard rom i guess. Im just a normal user that need to hv the phone working like it used to be. Lol
Sent from my GT-N7000 using xda premium
The total of 1 week I was on both OS builds I had these issues that I identified to be the battery:
Facebook
GPSD
and then not going into deep sleep (the phone gets warm)
Badass Battery (now another name, but you can still search Badass battery) and BBS (Better Battery Stats) helped me.
Thanks zkye.
So far i hv been using pretty alot of apps. Been using carat,netqin and cpu spy. Well the batt is still i would say average.. Im wondering how to read this thing on cpu spy. Especially the deep sleep graph. Is it sufficient? Or am i doing the wrong thing or what?
Sent from my GT-N7000 using xda premium
safuan7822 said:
Baz77,
Im not sure which rom tho. Well i hv totally no idea. Its a stndard rom i guess. Im just a normal user that need to hv the phone working like it used to be. Lol
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
You can check version in settings, then about phone in bottom Guess you are on stock. Be carefull wiping, factory resetting and deleting large files as kernel can trigger a bug in emmc chip, corrupting partitions.
good you started analysing root causes. Always best case.
now if you dont care for warrantee you can follow directions from this post http://forum.xda-developers.com/showthread.php?p=29139461 to get back to starting point of install. Or to install the awesome speedmod kernel.
Alteratively you can add apps one by one and together with battery usage analysed you can fin culprits. With tools like betterbatterystats, cpu spy and badassbattery monitor
Sent from my GT-N7000 using Tapatalk 2
did you try re-calibrating your battery?
Hi xfox,
Done with calibrating as in let it empty, take out the batt for a while then turn it on again. It seems okay for now. Is there any other way instead? Im sorry for asking this stupid question again and again. And thank to all of ya for replying my so called newby question. Lol.
Sent from my GT-N7000 using xda premium
Thanks baz,
How i wish i could use those speedmod kernel and so on. Well im quite afraid to root it cuz im not too sure that im gonna use this phone for a long time. As the phone value will decrease if i void the warranty. But thx for replying my post tho. As for now im still monitoring my batt behaviour.
Sent from my GT-N7000 using xda premium
jonpaslim said:
Calibrate your battery.
Let it empty untill blackout. Take out battery for 2 min then put it back again, and charge it to full, do not push the on button while charging.
Click to expand...
Click to collapse
this done it for my brothers Note
thanks
Galaxy Note problem
When I got my Galaxy Note, the battery used to last for 10 hrs on GB. After upgrading to ICS, that time dropped to 8 hrs. And after ICS updates, it went down to less than 4 hrs since it was discharging much fatser than charging, and it was the same whether I used the original power charger or direct USB cable.
The original charger is an adapter + USB cable.
Everything went fine when i changed the USB and used the one originally used to charge the Sony 3D glasses.
Now it's charging normally and the discharge rate is around 8% /hr with WIFI and mobile data ON.
Hope it will work for you.

[HELP] battery drains horribly

please help me, my battery is draining like HELL on my ace, i have just installed CM7 Apocalypse because on Stock it drained too much, but now is worst. It started dropping from 100 to 74 now its stopped at 74 but anyway help, i have used all kernels.
Sent from my GT-S5830 using xda premium
Battery = Samsung stock roms
madman said:
Battery = Samsung stock roms
Click to expand...
Click to collapse
That doesn't help man.
Probably a battery calibration problem... Wait until ALL the battery has drained, when it reaches about 2-3% then screenshot. The battery's indicator in the ace is quite buggy. When it says 74% it probably means 90%
Sent from my GT-S5830 using xda app-developers app
jleonnn said:
Probably a battery calibration problem... Wait until ALL the battery has drained, when it reaches about 2-3% then screenshot. The battery's indicator in the ace is quite buggy. When it says 74% it probably means 90%
Sent from my GT-S5830 using xda app-developers app
Click to expand...
Click to collapse
I will try, thanks
Sent from my GT-S5830 using xda premium
Idrito said:
I will try, thanks
Sent from my GT-S5830 using xda premium
Click to expand...
Click to collapse
Also you can try juicie defender, search it on the playstore.
Just fully charge your phone. Not when it hits 100% in 30 minutes you gonna pull the charger.
Sent from my GT-S5830
If your ROM drains too much battery, try another, such as droidace, or maxiAce I'm using now, both of them are good at battery as well as the UI.
Sent from my GT-S5830 using xda app-developers app
jleonnn said:
Probably a battery calibration problem... Wait until ALL the battery has drained, when it reaches about 2-3% then screenshot. The battery's indicator in the ace is quite buggy. When it says 74% it probably means 90%
Sent from my GT-S5830 using xda app-developers app
Click to expand...
Click to collapse
I did it, its the same
[N]ano® said:
If your ROM drains too much battery, try another, such as droidace, or maxiAce I'm using now, both of them are good at battery as well as the UI.
Sent from my GT-S5830 using xda app-developers app
Click to expand...
Click to collapse
Which i can use for a GOOD battery? i have tried everything
Sent from my GT-S5830 using xda premium
Idrito said:
please help me, my battery is draining like HELL on my ace, i have just installed CM7 Apocalypse because on Stock it drained too much, but now is worst. It started dropping from 100 to 74 now its stopped at 74 but anyway help, i have used all kernels.
Sent from my GT-S5830 using xda premium
Click to expand...
Click to collapse
This is common in Cyanogenmod roms. So, Firstly, change your Battery Status Style to Icon.
The instant when battery says 100% or charged, actually it's not fully charged. You'll still see the spark in battery's icon. Keep it charging for extra 30-45 mins. Also, when the battery is fully charged, you'll not see that spark in battery's icon while the charger is plugged in.
Sent Via XDA™ Premium
Wipe baterry status should help, go to CWM recovery / adwanced / choose it: wipe baterry status and restart.

Battery drain while charging after new rom install

I recently installed the latest version of Paranoid Android running Jelly Bean 4.2. Since then I've not been able to charge from usb or car charger. Charging from the wall socket works but is SLOW.
I'm stumped as to what the problem is, Google and the paranoid android thread haven't helped so I really am at a loss.
Any help would be great. Thanks guys.
Sent from my GT-N7000 using xda app-developers app
Shameless self bump
Sent from my GT-N7000 using xda app-developers app
Battery calibration
georgeos said:
I recently installed the latest version of Paranoid Android running Jelly Bean 4.2. Since then I've not been able to charge from usb or car charger. Charging from the wall socket works but is SLOW.
I'm stumped as to what the problem is, Google and the paranoid android thread haven't helped so I really am at a loss.
Any help would be great. Thanks guys.
Sent from my GT-N7000 using xda app-developers app
Click to expand...
Click to collapse
Have you tried make battery calibration ?
It's a known issue after flashing a new ROM.
qnt said:
Have you tried make battery calibration ?
It's a known issue after flashing a new ROM.
Click to expand...
Click to collapse
How might I do that?
Sent from my GT-N7000 using xda app-developers app
georgeos said:
How might I do that?
Sent from my GT-N7000 using xda app-developers app
Click to expand...
Click to collapse
The simplest way to do is power off you GN. Plug it into a power supply for recharge. When the level reaches to 100%, unplug and get out the battery. Wait for 5 minutes before put back the battery into the GN. Then restart it.
Otherwise get an appli like Battery Calibration, recharge the battery until 100%, the start the appli to calibrate it.
qnt said:
The simplest way to do is power off you GN. Plug it into a power supply for recharge. When the level reaches to 100%, unplug and get out the battery. Wait for 5 minutes before put back the battery into the GN. Then restart it.
Otherwise get an appli like Battery Calibration, recharge the battery until 100%, the start the appli to calibrate it.
Click to expand...
Click to collapse
But that sounds like I calibrating the battery itself. I use multiple batteries with my GN. Would it have an effect or am I doing something within the phone itself? Because both batteries drain while charging.
Also if I should do this then should I keep the charger plugged into the GN while I've taken the battery out?
Sent from my GT-N7000 using xda app-developers app
I read something about fast charge in the kernel? Any way to get it?
Sent from my GT-N7000 using xda app-developers app
georgeos;40541121
Also if I should do this then should I keep the charger plugged into the GN while I've taken the battery out?
Sent from my GT-N7000 using xda app-developers app[/QUOTE said:
No,unplug the charger.
I also have 2 batteries. Often, but not always, after a new ROM flash, battery recharge takes long time when the GN is On.
In such case I have make calibration for all my batteries. For each new ROM, calibration once for each battery is sufficient.
Click to expand...
Click to collapse

Categories

Resources