For anyone having the infamous left side screen lift issue. This includes being able to physically see the glass protruding the silver bezel, screen sponginess, and being able to hear the screen stick/unstick from the adhesive.
After reading this thread http://forum.xda-developers.com/showthread.php?t=1800418 it is apparent the screws are a hair too long. When tightened all the way, they actually can press the screen glass out.
The easiest thing for anyone to try is to just LOOSEN the screws just 1/4 turn. You are loosening the screws so very little, that they will stay snug as far as holding what they are supposed to, but they will no longer push out on the screen glass. I didn't even bother with finding a screw driver, and just used my pocket knife. My screen was raised in the very middle of the left side, so I only loosened the 2 screws directly under the seperation. I suppose this will not work for everyone, but it's so simple and only took me less than 2 mins, you might as well give it a shot. Good luck!
Great thanks
Sent from my Nexus 7 using Tapatalk 2
If you're going to loosen screws you probably want to Loctite them.
http://forum.xda-developers.com/showpost.php?p=29457665&postcount=41
eh hem...what gave you this idea? jk
Just don't overdo it and you'll be fine. No need for loctite, it's only a small turn and the screws are still plenty secure.
---------- Post added at 12:29 AM ---------- Previous post was at 12:28 AM ----------
Loosening the screws in some areas will also help with backlight bleed. If you notice a spot near a screw that is really bright, it's most likely a little too tight.
I found this out by testing different "tightness" adjustments. When I went too far, I noticed back light bleed starting to show, loosen it up a bit and it went away.
This actually worked! So far, anyway. We'll see if it's a permanent fix, but it looks promising.
ferris2375 said:
http://forum.xda-developers.com/showpost.php?p=29457665&postcount=41
eh hem...what gave you this idea? jk
Just don't overdo it and you'll be fine. No need for loctite, it's only a small turn and the screws are still plenty secure.
---------- Post added at 12:29 AM ---------- Previous post was at 12:28 AM ----------
Loosening the screws in some areas will also help with backlight bleed. If you notice a spot near a screw that is really bright, it's most likely a little too tight.
I found this out by testing different "tightness" adjustments. When I went too far, I noticed back light bleed starting to show, loosen it up a bit and it went away.
Click to expand...
Click to collapse
Lol yeah I saw your posts. I mean, that's the same thing I thought of right away. The washers seemed to be a stiff foam, so they compress when screws are tightened. I figured I could loosen them but at the same time keep them snug.
But yeah man good stuff. Did it work for ya?
This.
The washer idea is smart, but for me it caused a more annoying problem. The frame was too thick and pulled the silver trim piece away from the screen and caused a creaking noise at the slightest touch that was way worse than the screen lift.
I just loosened every screw and tightened them back with basically no torque after they stopped turning. All is good now, no creak from the trim and no screen lift, though it's basically flush on he left side
Sent from my Nexus 7
jweitzel24 said:
This.
The washer idea is smart, but for me it caused a more annoying problem. The frame was too thick and pulled the silver trim piece away from the screen and caused a creaking noise at the slightest touch that was way worse than the screen lift.
I just loosened every screw and tightened them back with basically no torque after they stopped turning. All is good now, no creak from the trim and no screen lift, though it's basically flush on he left side
Sent from my Nexus 7
Click to expand...
Click to collapse
Cool. So did you end up loosening the screws then? Meaning, when you re-tightened them, you didn't tighten them as tight as they were from the factory?
Very interesting... I thought the glass was supposed to be flush with the bezel, until I read your comment. After looking at it, the left side of my glass is also flush with the bezel, while the right side glass sits just a little lower.
That's no big deal to me though, as long as my screen is seated properly.
jaycustom said:
Cool. So did you end up loosening the screws then? Meaning, when you re-tightened them, you didn't tighten them as tight as they were from the factory?
Very interesting... I thought the glass was supposed to be flush with the bezel, until I read your comment. After looking at it, the left side of my glass is also flush with the bezel, while the right side glass sits just a little lower.
That's no big deal to me though, as long as my screen is seated properly.
Click to expand...
Click to collapse
Probably a little lighter than factory. Honestly, mine wasn't bad to begin with but like every other ocd person on here, I just couldn't resist opening it up and tightening the screws. At that point, the screen lift started getting worse and I moved on to the other half-dozen or so "fixes" when, it turns out, the screws being too tight was making everything way worse.
But yeah, its been a couple hours now and it still feels real solid. I've got a tpu case on order so regardless I'm done messing with it.
Sent from my Nexus 7 using xda app-developers app
jweitzel24 said:
Probably a little lighter than factory. Honestly, mine wasn't bad to begin with but like every other ocd person on here, I just couldn't resist opening it up and tightening the screws. At that point, the screen lift started getting worse and I moved on to the other half-dozen or so "fixes" when, it turns out, the screws being too tight was making everything way worse.
But yeah, its been a couple hours now and it still feels real solid. I've got a tpu case on order so regardless I'm done messing with it.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Cool beans. Luckily, like your N7, mine wasn't bad either.
Couldn't really tell it was lifted by looking at it, but it was the sponginess and that horrible stick/un-stick sound. This is the first fix I tried, and luckily it worked. Let me know how yours turns out, with or without the case..
I simply loosened all screws then tightened them up. Also, Part of a sponge bumper was tucked under a copper shield which I untucked.
Now when I push hard on the left part of the screen I don't get the tacky sound when i unpress it. Also, screen isn't as bulged. In fact you can't even tell anymore.
Neither was a real problem on my n7 but I prefer to make it perfect. This solved everything.
MikeMurphy said:
I simply loosened all screws then tightened them up. Also, Part of a sponge bumper was tucked under a copper shield which I untucked.
Now when I push hard on the left part of the screen I don't get the tacky sound when i unpress it. Also, screen isn't as bulged. In fact you can't even tell anymore.
Neither was a real problem on my n7 but I prefer to make it perfect. This solved everything.
Click to expand...
Click to collapse
Awesome. Mine wasn't bad either, so I just tried for something simple. It seems like the screws may be too long and pressing on the glass, so I thought to just back them off a hair. 2 minutes later the screen is perfect
jaycustom said:
Awesome. Mine wasn't bad either, so I just tried for something simple. It seems like the screws may be too long and pressing on the glass, so I thought to just back them off a hair. 2 minutes later the screen is perfect
Click to expand...
Click to collapse
If you take one of the screws out near the central left and shine a light straight down, you will notice that it is open on the other side as in the the screw can pass through. You will also see a portion of the LCD sticking out underneath those screw holes.
I think the LCD isn't suppose to stick out and get underneath the holes, because otherwise the screws won't hit anything and be tightened all the way. I think for some people without screen lift, the partially sticking out LCD might have been crushed and deformed with the screws or the LCD just isn't sticking out as much.
I've been screwing (pardon the pun) about with this some more today, what I have noticed with mine, is if I take the back off and remove all screws the screen sits perfect, put the screws back in, still seems perfect, clip the back on and the screen now sits above the frame on the left, wondering if mine is an issue with the back plate pushing something out of line.
This worked for a while for me but after it heated up the spongy noise returned. HOWEVER I did notice that loosening the screws did fix the touchscreen issue where it was unresponsive at times.
jaycustom said:
Lol yeah I saw your posts. I mean, that's the same thing I thought of right away. The washers seemed to be a stiff foam, so they compress when screws are tightened. I figured I could loosen them but at the same time keep them snug.
But yeah man good stuff. Did it work for ya?
Click to expand...
Click to collapse
Haha. I was just messing with ya. This is certainly better than adding a shim but I never had the problem. I just wanted to test this out and take my screws back a bit just in case. The other fix is not the way to go as it screws up the casing.
Still no issues though.
Sent from my Nexus 7 using Tapatalk 2
Summerfly said:
If you take one of the screws out near the central left and shine a light straight down, you will notice that it is open on the other side as in the the screw can pass through. You will also see a portion of the LCD sticking out underneath those screw holes.
I think the LCD isn't suppose to stick out and get underneath the holes, because otherwise the screws won't hit anything and be tightened all the way. I think for some people without screen lift, the partially sticking out LCD might have been crushed and deformed with the screws or the LCD just isn't sticking out as much.
Click to expand...
Click to collapse
Thanks for this.
I'm going to open it up again and consider using mini-washers, or something, just to ensure my now-tightened screws are not pressing on the LCD.
Genius. Popped the back off with a knife, loosened the screws down the left side of the screen a quarter of a turn, and now it's perfect - no more squeaking, no more raised screen. Took about 2 mins to do it.
Also, for those who want a decent cover, I bought a Belkin case from PC World yesterday (quite pricey at £30 but I like to try these things out before I buy them rather than just buy online). Even though it's designed for the 7" Samsung Galaxy Tab, it's a near-perfect fit for the Nexus 7. Speaker cut-out is in the wrong place but it doesn't affect the quality noticeably (besides, I hook mine up via Bluetooth to a Jawbone Jambox). Also got myself a sat nav mount and stuck it on the wall next to my bed, so my Nexus 7 is now a handy portable TV
I fixed mine without even getting inside. Just used a blowdryer and heat up the side while holding the screen down. Seemed to stay put and still is.
Simply awesome, completely fixed that annoying screen bulge on the left side!
Related
So rather than sending back my Nexus 7, I decided to give something a try. I removed the back casing, which is very easy to do. I used a small flat screwdriver where the "leather" meets the plastic and gently wedged it in. The case popped right open and was easily removed. I then tightened all of the small phillips screws around the outside of the board on the back of the screen.
This immediately cleared up the creakiness and play that i was experiencing on the left side of the screen. I tightened all screws and not just the ones on the left side. Do this at your own risk, obviously, but this immediately rectified my issue!
7/22 update:
So on Friday, I noticed a slight creak returned. I removed the black strip of foam that has been discussed in this thread. Since Friday, with heavy use, no creak, no play, no screen rise I'll update again later in the week to confirm it hasn't returned.
8/02 update:
Since removing the sponge, the play in the screen and the creaks have not returned. I see others havent had as much luck with it but, for me, I can say it did the trick.
Update 1: People are reporting that after a few hours the issue came back. It does appear to be something else causing this. If your issue persists, Call Your Store!
Update 2: Included another guide in this post to try, thank you Luxferro & Evo_Shift
Update 3: Most of us Play Store people are closing in on 15 day replacement time. It's quick & painless, and you still get to use your tablet while the other one is being shipped. Call them, RMA it, get it taken care of.
Update 4: Added Washer Fix Guide. Received my new replacement from the google store. Worse than my older one. Uploaded a video below. Google told me to google the fix for it and try it.
NOTE: Me & Jam are not responsible for what damage you may cause. Nobody has noticed any warranty seals being broken.
______________________________________
Do I have screen separation?
______________________________________
http://www.7nex.us/wp-content/gallery/defects/buldge5.jpg
______________________________________
Guide One - Washer Fix by dilldoe
______________________________________
Main Idea: http://imgur.com/QbGxi | Original Post: http://forum.xda-developers.com/showpost.php?p=29363298&postcount=638
UPDATE: PICTURES & GUIDE - http://forum.xda-developers.com/showpost.php?p=29422550&postcount=1
Using the thin plastic from a pill blister (allergy pills were right in front of me when I was doing this) I created a washer to space out the frame & screen.
Just cut a rectangle out and punch a hole at the end for the screw to go thru. I just used a sewing needle on a sewing machine, like a drill press, to make a starter hole and my smallest screwdriver to widen it. With the screwdriver still in the hole, I just ran my knife around it to trim off the excess plastic.
WHY A LONG RECTANGLE? so you can insert it and hold it in place while you work. don't want it accidentally falling into the device.
now just slide that UNDER the top frame and screw it back together. MAKE SURE YOU STOP ONCE IT'S SNUG. the screen should now be lower than the side bezel.
Do this to all the spots that are lifting. I just did mines on the lower left and upper right, since they both had slight lift.
After you're done screwing it all down, trim off the excess so you can put the back cover back on, not flush to the frame, just enough so you can hold it if you need to remove it.
Did this last night and this afternoon, still no returning lift.
edit: depending on how much lift you have, you might have to use 2 or more to fill the gap (or use something thicker like used gift cards)
Follow ups:
http://forum.xda-developers.com/showpost.php?p=29384275&postcount=677
http://forum.xda-developers.com/showpost.php?p=29405347&postcount=710
http://forum.xda-developers.com/showpost.php?p=29402365&postcount=700
______________________________________
Guide Two - Simple Tighten by cwc3/jam10238
______________________________________
1) Grab something that isn't going to mar your nice silver plastic. People have been using guitar picks & even their fingernails
2) Stick that non-marring object between like seen here: http://guide-images.ifixit.net/igi/CAKD1lCgchEPlBI2.medium (they have a white cover while we have a black one)
3) Start sliding that object between the two, you will notice them starting to pop up. Try not to pry if you can, I had to a little.
4) Should now look like this: http://guide-images.ifixit.net/igi/1S3nvadn4UKYoEVx.medium
5) Tighten all the screws around the outside (Pretty much eye glasses size), on the black plastic and metal. Not too tight, or you might cause back-light bleed &/or strip the screw. In my case most were a little loose.
6) When putting the case back on, be sure your not just starting flat. Start at a angle, for example, with the right side portrait. Push/Pop it back on going around the tablet.
Pictures I took taking it apart:
http://i.imgur.com/4dG2d.jpg?1
http://i.imgur.com/ONTTp.jpg?1
http://i.imgur.com/A3zfP.jpg?1
______________________________________
Guide Three - Advanced Tighten by Luxferro
______________________________________
Original Post: http://forum.xda-developers.com/showthread.php?p=29022274#post29022274
1) Loosen all the screws around the outside w/ the panel on a flat hard surface (hard cover book)
2) Let the panel re-seat itself a bit
3) Just barely tighten all the screws.
4) Then repeat the tightening once they are all done to snug them up (not too much!). It should make your screen look perfect.
4a) After a bit of use you might need to snug them up once more - if the glass starts popping up again.
I tried this method of losening the screws after just tightening them failed me. And so far over 12 hours later my device still is good
Follow up:
http://forum.xda-developers.com/showpost.php?p=29028109&postcount=235
________________________________________
Interesting Links:
Someone removing some of the foam to compensate - Do not recommend (Warranty May Be Void)
Full ifixit teardown: http://www.ifixit.com/Teardown/Nexus-7-Teardown/9623/1
Post a vid!
---------- Post added at 12:55 PM ---------- Previous post was at 12:55 PM ----------
So the problem most of us have is cause ASUS didn't tighten some screws.. hahh
Thanks for TOFTT!
When you snapped the case back on there was no evidence that you opened it?
cwc3 said:
You brave, brave man.
For anyone as brave as him, here is a tear down guide: http://www.ifixit.com/Teardown/Nexus-7-Teardown/9623/1
Click to expand...
Click to collapse
Ha! It really sounds a lot worse than it is. Removing my Galaxy Nexus battery cover is almost as difficult!
Sent from my Galaxy Nexus using Tapatalk 2
jam10238 said:
So rather than sending back my Nexus 7, I decided to give something a try. I removed the back casing, which is very easy to do. I used a small flat screwdriver where the "leather" meets the plastic and gently wedged it in. The case popped right open and was easily removed. I then tightened all of the small phillips screws around the outside of the board on the back of the screen.
This immediately cleared up the creakiness and play that i was experiencing on the left side of the screen. I tightened all screws and not just the ones on the left side. Do this at your own risk, obviously, but this immediately rectified my issue!
Click to expand...
Click to collapse
Brave indeed! Tempted to do this since I have the same problem but 1) don't wanna wait 1h on hold trying to get an RMA and 2) who knows when I'd be getting a new one.
In case I try this, and it ends up not fixing the issue and I decide to send it back later, do you think Google would be able to tell that device has been opened and potentially refuse the exchange?
Thanks
I might give this a try tonight after having an adult beverage to calm my nerves.
Thank you for doing it. I'll give it a go when I get home. Did you use a regular flat head or a plastic device friendly one?
Sent from my Galaxy Nexus using xda premium
laverdure#1 said:
Brave indeed! Tempted to do this since I have the same problem but 1) don't wanna wait 1h on hold trying to get an RMA and 2) who knows when I'd be getting a new one.
In case I try this, and it ends up not fixing the issue and I decide to send it back later, do you think Google would be able to tell that device has been opened and potentially refuse the exchange?
Thanks
Click to expand...
Click to collapse
I dont think so, there is absolutely ZERO warranty tape or anything that is standard on electronics these days. Its literally like a big battery cover. I can post a video shortly of the process.
Sent from my Galaxy Nexus using Tapatalk 2
Pithism said:
Thank you for doing it. I'll give it a go when I get home. Did you use a regular flat head or a plastic device friendly one?
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Just a very small standard precision flat head. Fingernails may even work it was that simple.....
Sent from my Galaxy Nexus using Tapatalk 2
Were the screws that you tightened noticeably loose?
adamhlj said:
Were the screws that you tightened noticeably loose?
Click to expand...
Click to collapse
There were absolutely 3 or 4 that were a half turn loose.
Sent from my Galaxy Nexus using Tapatalk 2
Videos or pictures would be clutch
Sent from my Galaxy Nexus using xda premium
cwc3 said:
You brave, brave man.
For anyone as brave as him, here is a tear down guide: http://www.ifixit.com/Teardown/Nexus-7-Teardown/9623/1
Click to expand...
Click to collapse
You only need to do step 4 in this guide and thats it. If you look at the image for step 5 or 6 youll see one of the screws i tightened in the lower right corner of the picture.
Sent from my Galaxy Nexus using Tapatalk 2
I have the minimal screen yellowing issue on the right side of the screen. Do you think this could possibly solve my problem?
Sent from my Nexus 7
I'm going to bookmark this for now, but not worry about it as it stands.
I finally noticed just a thumbs size spot in the upper left that i could sometimes hear a LITTLE give, but that was in my quiet bedroom.
Otherwise it didn't feel like it was really having any give or separation.
So for now, I don't think I'll tempt fate, everything else seemed good in my build quality based on what some folks are reporting. Lightbleed I know from my old G2x, and got none, no discoloration or dead pixels that I could see. So given my luck I would tighten up this little almost not noticeable issue, and ... cause 2 more things to start acting up for no discernible reason at all.
Thanks though.
Just used my finger nail. Came off no problem. just don't have a screw driver that small at work.
Sent from my Galaxy Nexus using xda premium
Pithism said:
Videos or pictures would be clutch
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Honestly, the teardown guide has better pictures than i could ever take. Once you pop the cover off, just gently give all exposed phillips screws around the outside a turn until tight. Dont force anything. Go the entire way around the outside then just pop the cover back on and power it back up.
Sent from my Galaxy Nexus using Tapatalk 2
Yea they are good pictures. I will look at those again. Really easy to do people
Sent from my Galaxy Nexus using xda premium
Those who got it popped off successfully, post some pics/video!
Ok, so I have had the screen lift problem. It's on the left side worst in the middle. I decided I would take it apart and do the shims between the screws thing. But when I got it open the lift disappeared. So it's a problem with the back pressing up just enough... I noticed a pretty thick piece of foam right on the center left so I removed it. Just replaced the case and tada the tape is holding the screen flat just fine now. Just thought I would pass this on with the other fixes.
Danny80y said:
Ok, so I have had the screen lift problem. It's on the left side worst in the middle. I decided I would take it apart and do the shims between the screws thing. But when I got it open the lift disappeared. So it's a problem with the back pressing up just enough... I noticed a pretty thick piece of foam right on the center left so I removed it. Just replaced the case and tada the tape is holding the screen flat just fine now. Just thought I would pass this on with the other fixes.
Click to expand...
Click to collapse
I noticed last time I opened it that this foam had some compression marks. Likely from pressing against the back. Mine was slightly misaligned, so really only part was compressed. I had the same thought, i.e. remove it. Maybe align it, but it's glued on tight.
So I just removed it. I'll let you know how it turns out in a day or 2.
I also use 3 washers for the top 3 on the left, which helped huge. Hopefully this will make it perfect.
Update Sept 1. This definitely helps. Noticed from pics on another thread that some new models have this foam removed, as shipped. Interesting. Also, on new models, some have screws missing (2 and 4, starting top left). I tried removing screw 2 but when I woke up I noticed creaking and movement at the bezel, when I press my left thumb inwards, which is something I always do. So I put the screw (and washer) back in this morning. Perfect now. But removing this foam was essential, so thanks again.
Makes sense. The screen is dead flat, so it has to be the back case that is separating. Thanks for the info.
Sent from my Nexus 7 using Tapatalk 2
this isn't new and has already been covered already.
dilldoe said:
this isn't new and has already been covered already.
Click to expand...
Click to collapse
Can you point to where the foam issue was already covered? It was the first I saw.... maybe they have more pointers... Links?
Sent from my Nexus 7 using xda premium
mike5065 said:
Can you point to where the foam issue was already covered? It was the first I saw.... maybe they have more pointers... Links?
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1781237
http://forum.xda-developers.com/showpost.php?p=29028614&postcount=237
mike5065 said:
Can you point to where the foam issue was already covered?
Click to expand...
Click to collapse
It was covered in the main screen lift thread, which is like 90 pages long and has every possible remedy tested, dissected and mostly debunked. The fact is there are several factors causing the lift and there need to be several solutions to really fix it 100%, and permanently. You can make it better in various ways, one of which is removing that foam, although I believe the foam is there to keep the back from flexing and compressing those metal "prongs", causing them to lose contact. So you might have other problems later without the foam. I probably wouldn't mess with it, personally.
I personally think a workable solution for most N7's with this problem would be to shave that foam down evenly by like 0.3mm, then clamp the screen to the trim and leave it in a hot car like that for a day or so to re-adhere, without the back cover on. Then cool the tablet down and replace the back cover. The hard part is evenly shaving down the foam; it is just a tiny bit too big. But it should be present.
Well I thought I could live with it but the lift is back.... I have also noted that my 8gb gets really poor wifi connection compared to my wife's 16gb. All the clips are still contacting the back plate but I can see no difference in signal with or without the back on. So, I just called google and they are shipping out a new unit for me tomorrow. Hopefully this one is better.
Took the back off to look at screen lift fix. Low & behold 3 screws missing on the LH side of the unit. Also some fingerprints on the copper plates, 2 loose (more than 1 full turn to tighten) screws on the RH side, metal tape/gauze over phone socket loose.
badasscat said:
...So you might have other problems later without the foam...
Click to expand...
Click to collapse
Thanks for all this info. My foam was glued at about 25 degrees off-angle, and clearly compressed at the corner closest to the bezel, so a problem for mine' right from the factory. I didn't get it all off, but most for sure. Once removed, the bulge I had at that point between the bezel and rear case was gone. So was some screen lift' although the washers helped more for that. Not a big win, just another step forward.
I'm still curious why some pics on other thread show no foam, as shipped.
http://forum.xda-developers.com/showthread.php?p=30974024
From my looking, it's in a seemingly non-functional gap, and presses down a wide cable (or something). I earlier traced movement of that cable as the source of 'creaking' I was having, i.e. when it moved against another piece of plastic beside the bezel. I put some lithium where it rubbed and the creaking stopped. Mind you I did that (and the 3 washers precisely tightened) before i removed most of the foam.
My Tf101 was a lot less maintenance than this one. But once done (crossing fingers lol), it's causing my iPad3 to collect dust. This thing just screams. Loving it.
Again, thanks for the info.
Sent from my Nexus 7 using xda premium
I didn't want to start a new thread regarding the screen lift issue,bit the solution is extremely simple even my grandma could do it!
I started to expirience the screen lift issue. A few weeks ago it started with a kind of creaking sound coming from one of the sides of the screen....with my finger I could feel that the display glass was slightly higher than the bezel on the side while the rest of the display sat slightly recessed. After some time this issue only became worse with one side of the display protruding by at a couple of milimetres, something had to be done.... I'm well versed in hardware repair but this issue found me lazy and in bed.
These are the steps I took while still under my blankets:
-used my thumb nail to separate the display from the backing case. Was extremely easy, I started exactly in the center of the top (behind the camera and in between where the textured back meets the silver bezel.)
-ran my thumb nail around the entire bezel, at times gently using my fingers to lift a little and the nexus backing easily popped off...very easily
-with the backing off now the screws that tighten the display down were exposed around the perimeter of the logic board/ motherboard ...took a precision Phillips and tightened them all up, they were loose.
-snapped the back back on, good as new
I've done that and it works...for a little while then comes back. At this point I've given up, asked my wife to get me a new nexus 7 for Christmas, between creaking issues that always come back, and intermittent lag I think its time to move on.
Sent from my Nexus 7 using Tapatalk 4
Use Caution
When the n7 FIRST came out this was a HUGE Issue. there were thread after thread about this. and even a few poles . Most people from my reading had there screen break a few days to a week or so after tightening those screws. A few people took their nexus apart and re glued the screen down . Most of there stayed fixed and did NOT CRACK.
Most have said Its a Design flow in the Frame work around the Glass . on the left side of the device where the Display connector is there is NO Support for the glass .
Be careful
aS SAID in the many other Threads about this issue. I replied here just incase you Decided to Not read about others experiences with this problem. Tightening those screws the screen can't flex with heat changes and WILL CRACK
i started having the screen lift issues after i dropped my nexus 7 from my desk (stupid me,i had it on a vitamin bottle lol).
I can press down and the screen will even out but it lifts back up after a while. I just got a case and now it doesnt bother me,cant really tell.
does the lifting cause a problem for the touch input later or something?
---------- Post added at 09:40 AM ---------- Previous post was at 09:39 AM ----------
i started having the screen lift issues after i dropped my nexus 7 from my desk (stupid me,i had it on a vitamin bottle lol).
I can press down and the screen will even out but it lifts back up after a while. I just got a case and now it doesnt bother me,cant really tell.
does the lifting cause a problem for the touch input later or something?
So I foolishly offered to replace the broken screen on a Nexus 6. There's a lot of screws, but really good videos and there were no big surprises.
UNTIL...
I have no idea how to get the little black rectangles of plastic back in the holes at top and bottom of the phone. I've heard them called speaker grills, which is obviously inaccurate since it is a tiny slab of plastic with no holes.
But really I don't care what you call them. NO WHERE have I found anyone talking about how to put them back. There are a lot of posts about people that had them fall out. I guess Motorola FIXED that! They were extremely difficult to push out from the back side of the old screen. Nothing I do remotely comes close to popping them in to the new screen. I'm about ready to file off the tabs and use a drop of superglue. Perhaps that is even the "approved" repair.
But if anyone knows the right way to replace these things I'd love to hear it. I am fresh out of ideas.
I'm in the SAME position with my Moto X Pure and I can't find any info on the matter!
If you can, perhaps some pictures of the backside of both grille and screen may be useful here.
They were quite easy to pull off on mine and also easy to put back. However, when I clipped them back they got a bit lose so I had to add tiny drop of super glue on each of them before clipping it back on. Also, they aren't plastic turns out they're ceramic and I think I read somewhere that these were left over volume buttons from the Nexus 5.
Sent from my Nexus 6 using Tapatalk
I think I'm going to take a dremel to it and grind off the tab. This should allow it to sit down at the proper depth. Then some superglue. I am now worried about sticking ceramic to plastic. But grinding should show if it is plastic or not. And I have to do something. This phone can't just sit in the middle of my workspace forever.
I am not remotely a superglue fan. It always seems remarkably good at holding what it should not while what it should just slides off. (yes I do buy the correct version based on label). But we'll see.
Good luck but be careful you don't accidentally drop some on the mesh. I'm still wondering as to why it's not clipping back in with you. Almost everywhere I read it's pretty darn easy and straight forward.
Sent from my Nexus 6 using Tapatalk
Is anyone else's xz1 compact body bent or not straight?
I have had mind a couple of weeks and been super careful with it, so I don't think I bent it or something. I didn't notice until today when I set my phone down on a flat table as I was finicking with it when I noticed it rocked back and forth and wasn't perfectly flat to the table. It is particularly noticeable in the front side (I think part of this is due to the edges around the screen not being completely flush or evenly flat. The back does it much less, but I think that may because of the curved back on the back. After looking down the back side of the phone I realized it was clearly not straight and could see It curve.
Anyone with similar issues? Thanks!
The border around the camera lens is protuding a tiny bit from the back of the phone, to protect the lens from scratches.
The top and bottom edges of the phone are protruding to protect the screen from being scratched when placed face down.
Though it does not rock for me.
What sort of curve?
Mine doesn't rock when on its back, and I have a screen protector on the front which is slightly taller than the top and bottom metal caps, so it is also stable.
When I bought my phone in store, per procedure they had me inspect the phone for obvious damage or defects.
The first unit I got unfortunately had assembly issues with the top and bottom metal caps, there was a noticeable gap on both ends and they protruded unevenly. One end protruded to the front, and the other to the back.
At first they tried to play it off as non-issue, citing manufacturing tolerance, and refused to let me exchange a new one, but I insisted and eventually they agreed to give me another unit, which is the one I'm currently using.
Does your unit have similar unevenness with the metal caps? Maybe that's the cause of the instability. I do not perceive any curves on the body of my phone.
The border around the camera lens is protuding a tiny bit from the back of the phone, to protect the lens from scratches.
The top and bottom edges of the phone are protruding to protect the screen from being scratched when placed face down.
Though it does not rock for me.
Click to expand...
Click to collapse
I didn't think about the camera, good point, that may be some of the issue when it's on its back. The rocking when it's on its back is mild, so it may be the camera lens ring. However, I can look down the phone close with my naked eye and notice the bend pretty easily.
I do realize the front 'metal caps' protrude a little to protect the screen, but as mhaha says below, those edges are not necessarily uneven. The top metal cap sticks out further, in general, than the bottom. Individually, if I run my finger down the cap edges on the face of the phone I think I can feel where they get closer/further from the screen in places (it is very slight, so maybe that one is more in my head). I also didn't notice the uneven gap edge until you said that, I can't really physically feel that one so I think it's a little less of an issue. But, yes, on the left side of my screen it's super snug up against the side bezel and on the right I can see a very slight gap, in comparison.
My phone rocks bad on its face/front , diagonally from the cameras corner to the corner opposite.
I have actually requested my return (I ordered mine online) and will very likely be sending it back. I am not sure ill get a replacement either, for now just the return.
Thank you both very much!
mhaha said:
What sort of curve?
Mine doesn't rock when on its back, and I have a screen protector on the front which is slightly taller than the top and bottom metal caps, so it is also stable.
When I bought my phone in store, per procedure they had me inspect the phone for obvious damage or defects.
The first unit I got unfortunately had assembly issues with the top and bottom metal caps, there was a noticeable gap on both ends and they protruded unevenly. One end protruded to the front, and the other to the back.
At first they tried to play it off as non-issue, citing manufacturing tolerance, and refused to let me exchange a new one, but I insisted and eventually they agreed to give me another unit, which is the one I'm currently using.
Does your unit have similar unevenness with the metal caps? Maybe that's the cause of the instability. I do not perceive any curves on the body of my phone.
Click to expand...
Click to collapse
you may be having this issue?
https://sumahoinfo.com/xperia-xz1-compact-so-02k-docomo-fuguai-issue-body-twisted-distorted
It's in Japanese but the photo explains, I think.
yyiimm said:
you may be having this issue?
https://sumahoinfo.com/xperia-xz1-compact-so-02k-docomo-fuguai-issue-body-twisted-distorted
It's in Japanese but the photo explains, I think.
Click to expand...
Click to collapse
Yeah, my top metal cap isn't as in line as the bottom, now that I see that. Thanks very much! That would definitely contribute to a wobble on a flat surface.
But, there are still all the other issues I've noted, so I'm quite confident it's a number of issues contributing to it all.
Thanks!
yyiimm said:
you may be having this issue?
https://sumahoinfo.com/xperia-xz1-compact-so-02k-docomo-fuguai-issue-body-twisted-distorted
It's in Japanese but the photo explains, I think.
Click to expand...
Click to collapse
1230m said:
Yeah, my top metal cap isn't as in line as the bottom, now that I see that. Thanks very much! That would definitely contribute to a wobble on a flat surface.
But, there are still all the other issues I've noted, so I'm quite confident it's a number of issues contributing to it all.
Thanks!
Click to expand...
Click to collapse
The photo isn't quite a good descriptor of the problem though.
The photo suggests that it's just the way the metal end-caps are installed is what's causing the rocking.
If you run the link through a translator, the author states that the metal caps are misaligned because the plastic/glass-fiber body itself is warped.
So you may want to look at getting the phone replaced.
I dropped my phone on the road 2nd day of use. The metal edge got scratched, but the phone survived. The only other issue I noticed was twisted body. Looking from the edge, the twisted edge was easy to notice, and surface wobble was also there. I held the edges of the phone and put some pressure in opposite direction (trying to twist it back), and now my phone seems straight/aligned).
Please don't try this at home and come complain to me if something goes wrong. Since I dropped my phone, I couldn't just return it and get it replaced. Also not sure if the drop twisted it, or just pressure in my jeans pocket. Also not sure if the twist will come back. For now, the phone is fine.
I just bought XZ1 (not XZ1C) in UK, and having similar issue.
I'm not sure if the "cap" in misplaced or the whole body is twisted, but when I put the device face down, it rocks
pbarrette said:
The photo isn't quite a good descriptor of the problem though.
The photo suggests that it's just the way the metal end-caps are installed is what's causing the rocking.
If you run the link through a translator, the author states that the metal caps are misaligned because the plastic/glass-fiber body itself is warped.
So you may want to look at getting the phone replaced.
Click to expand...
Click to collapse
Thanks for the further insight, I'm grateful! I will be returning the phone. I'm undecided on whether or not I would like to purchase another after. I kinda wanted to see how the future quality/reviews are more. Based on some with similar issues, I'm not sure ill be getting another, but I'll see I guess. Thanks again!
I dropped my phone on the road 2nd day of use. The metal edge got scratched, but the phone survived. The only other issue I noticed was twisted body. Looking from the edge, the twisted edge was easy to notice, and surface wobble was also there.
Click to expand...
Click to collapse
Thanks very much for your input! I appreciate it. The body twist and warp (these are better way to describe it, thanks, as the phone isn't so much curved/bent as it, or the single piece back/body specifically, is warped) is quite noticeable with the one I have too (looking at the edge like you said). However, I don't think I've dropped the phone (too hard at least and no visible scrathes, scrapes, etc.) I also keep a phone in a coat pocket, bag, or just take it out and set it down when I'm not out and about, so I don't think I would have caused the warp myself. Thanks again!