Hi,
I just flashed Darky's rom 10.2 and now when I boot my phone I can see the GALAXY logo and the "powered by DarkCore.." but it stays like this for several seconds and then just become black and then the logo reappear all over...
the phone it self wont boot.
I cant enter recovery or download mode either.. if I keep pressing (the volume buttons) a battery (?!) icon is shown, if i release - The logo come back.
WHAT CAN I DO?
Don`t panic. This sounds like a pretty simple boot loop.
To get into download mode, plug your phone into the wall charger and use the three button combo. Flash back to stock and start all over.
remove the battery for few second. put it back and use three button combination to enter into download mode and try to flash RE. Make sure repartition is ticked. Check my signature for the guide...
But...
I had my lag fix turn on..
now i cant get to the settingh (cause the phone wont boot...)
It wont damage my phone to flash?
And by flash you mean with Odin and all the the basic GB?
Shouldnt i get to recovery mode and just flash the Darky 10.2 all over (with wipe and all..)
???
to start with YES i have googled the whole internet to find a sollution to this problem.............. i have found some hints to others have THIS problem but no solution......... and flashing overcome flashin anything else for that matter using Dowload mode / recovery mode is not possible at present ( unless some one knows the solution to this specific problem ( read below please )
Hello there i got my hands on 2 used GT-P1000, the first one had 2.3.3 on it when i got it as far as i remember , i proceeded to reflash it to Android 2.3.6 following a VIO vidoe on youtube and then flashed it to android 4.1.2 also following a VIO video.... it works super and there was no problems with it......
then i got the 2nd GT-P1000 and i wanted to do the same to it..... BUT and i didnt take notice at first.... but i remembered after that this one had the stock android 2.2...........
i tryed to flash it to 2.3.6 using odin and so on like i did the previous GT-P1000........... it resultet in beeing stuck in samsung boot loop so i thought ok i have to flash it back to stock and i googlet and found a rom that i thought was the stock rom and flashed it and got PASS from odin and so on.... ( i should proberbly have done a little more homework before the 2nd flash wich was done a little in the blind ) but then i reboobet the tablet at ended up with.... ( see below )
if power button is pressed the Tablet will turn on but will ONLY light up buttons and have black screen NO other signs of life........ i can hold power button at turn it off again.
if i hold volume down button and power button to enter download mode NOTHING happens.............. it dous not turn on or do anything................
if i hold volume up and power button it just turns on and lights buttons with black screen............ nothing else
if i plug it into the charger after a couple of minutes it lights up buttons with black screen and just stays like that untill turned off...........
if i plug the tablet into usb on my computer i get the usb plugged in sound like it regonizes the tablet and Odin shows that the tablet is there...... BUT odin keeps getting stuck on " <ID:0/003> SetupConnection.. " , i tryed unplugging and then plugging the tablet in fast as some one said in a post that you can do but odin just stops and says fail........... what ever i try to flash i odin gets stuck on <ID:0/003> SetupConnection..
i have tryed 2 different versions of odin....... 1.7 and the one in the vio video i used to flash the first tablet without a hitch..............
i also tryed oneclickunbrick thing wich cant see the tablet.............
in short ...........'
Tablet cant boot any mode , just lights buttons and black screen
is regonized by odin but will not accept any flash..........
help? please............ thanks in advance............
SOLVED!
Sollution:
Using the VIO youtube video upgrade to 2.3.6 content as described......
1. Make Odin ready with the rom in PDA as video describes.
2. connect tablet to computer while off and imidiatly hold down Vol Down and power button as if trying to get into Download mode, tablet will not light or show anything in screen up but computer will make USB detected sound... then press start in Odin......... it will flash the rom " P1000XWJQ8_P1000AUTJQ1_P1000XXJPZ_HOME.tar ".... follow the steps as described in VIO video EXEPT! do not let the tablet boot into android as the VIO guy says, turn it off and enter download mode and flash the 2nd file called " dbdata " and then follow his steps..... this is what i think prevented me from getting boot loop issue again................
i upgraded to the 4.1.2 by VIO also and the tablet works super! now....
i posted this to help others with THIS problem................. cheers.
How to fix bro. Email to me [email protected] thank you
:victory:
my tab keeps on turning the flash light on and off..
BMN2205 said:
to start with YES i have googled the whole internet to find a sollution to this problem.............. i have found some hints to others have THIS problem but no solution......... and flashing overcome flashin anything else for that matter using Dowload mode / recovery mode is not possible at present ( unless some one knows the solution to this specific problem ( read below please )
Hello there i got my hands on 2 used GT-P1000, the first one had 2.3.3 on it when i got it as far as i remember , i proceeded to reflash it to Android 2.3.6 following a VIO vidoe on youtube and then flashed it to android 4.1.2 also following a VIO video.... it works super and there was no problems with it......
then i got the 2nd GT-P1000 and i wanted to do the same to it..... BUT and i didnt take notice at first.... but i remembered after that this one had the stock android 2.2...........
i tryed to flash it to 2.3.6 using odin and so on like i did the previous GT-P1000........... it resultet in beeing stuck in samsung boot loop so i thought ok i have to flash it back to stock and i googlet and found a rom that i thought was the stock rom and flashed it and got PASS from odin and so on.... ( i should proberbly have done a little more homework before the 2nd flash wich was done a little in the blind ) but then i reboobet the tablet at ended up with.... ( see below )
if power button is pressed the Tablet will turn on but will ONLY light up buttons and have black screen NO other signs of life........ i can hold power button at turn it off again.
if i hold volume down button and power button to enter download mode NOTHING happens.............. it dous not turn on or do anything................
if i hold volume up and power button it just turns on and lights buttons with black screen............ nothing else
if i plug it into the charger after a couple of minutes it lights up buttons with black screen and just stays like that untill turned off...........
if i plug the tablet into usb on my computer i get the usb plugged in sound like it regonizes the tablet and Odin shows that the tablet is there...... BUT odin keeps getting stuck on " <ID:0/003> SetupConnection.. " , i tryed unplugging and then plugging the tablet in fast as some one said in a post that you can do but odin just stops and says fail........... what ever i try to flash i odin gets stuck on <ID:0/003> SetupConnection..
i have tryed 2 different versions of odin....... 1.7 and the one in the vio video i used to flash the first tablet without a hitch..............
i also tryed oneclickunbrick thing wich cant see the tablet.............
in short ...........'
Tablet cant boot any mode , just lights buttons and black screen
is regonized by odin but will not accept any flash..........
help? please............ thanks in advance............
SOLVED!
Sollution:
Using the VIO youtube video upgrade to 2.3.6 content as described......
1. Make Odin ready with the rom in PDA as video describes.
2. connect tablet to computer while off and imidiatly hold down Vol Down and power button as if trying to get into Download mode, tablet will not light or show anything in screen up but computer will make USB detected sound... then press start in Odin......... it will flash the rom " P1000XWJQ8_P1000AUTJQ1_P1000XXJPZ_HOME.tar ".... follow the steps as described in VIO video EXEPT! do not let the tablet boot into android as the VIO guy says, turn it off and enter download mode and flash the 2nd file called " dbdata " and then follow his steps..... this is what i think prevented me from getting boot loop issue again................
i upgraded to the 4.1.2 by VIO also and the tablet works super! now....
i posted this to help others with THIS problem................. cheers.
Click to expand...
Click to collapse
please help me.... my tab is just turning the flash light on and off.. after all the stuffs doing through odin. please help me to bring my tablet back.
BMN2205 said:
to start with YES i have googled the whole internet to find a sollution to this problem.............. i have found some hints to others have THIS problem but no solution......... and flashing overcome flashin anything else for that matter using Dowload mode / recovery mode is not possible at present ( unless some one knows the solution to this specific problem ( read below please )
Hello there i got my hands on 2 used GT-P1000, the first one had 2.3.3 on it when i got it as far as i remember , i proceeded to reflash it to Android 2.3.6 following a VIO vidoe on youtube and then flashed it to android 4.1.2 also following a VIO video.... it works super and there was no problems with it......
then i got the 2nd GT-P1000 and i wanted to do the same to it..... BUT and i didnt take notice at first.... but i remembered after that this one had the stock android 2.2...........
i tryed to flash it to 2.3.6 using odin and so on like i did the previous GT-P1000........... it resultet in beeing stuck in samsung boot loop so i thought ok i have to flash it back to stock and i googlet and found a rom that i thought was the stock rom and flashed it and got PASS from odin and so on.... ( i should proberbly have done a little more homework before the 2nd flash wich was done a little in the blind ) but then i reboobet the tablet at ended up with.... ( see below )
if power button is pressed the Tablet will turn on but will ONLY light up buttons and have black screen NO other signs of life........ i can hold power button at turn it off again.
if i hold volume down button and power button to enter download mode NOTHING happens.............. it dous not turn on or do anything................
if i hold volume up and power button it just turns on and lights buttons with black screen............ nothing else
if i plug it into the charger after a couple of minutes it lights up buttons with black screen and just stays like that untill turned off...........
if i plug the tablet into usb on my computer i get the usb plugged in sound like it regonizes the tablet and Odin shows that the tablet is there...... BUT odin keeps getting stuck on " <ID:0/003> SetupConnection.. " , i tryed unplugging and then plugging the tablet in fast as some one said in a post that you can do but odin just stops and says fail........... what ever i try to flash i odin gets stuck on <ID:0/003> SetupConnection..
i have tryed 2 different versions of odin....... 1.7 and the one in the vio video i used to flash the first tablet without a hitch..............
i also tryed oneclickunbrick thing wich cant see the tablet.............
in short ...........'
Tablet cant boot any mode , just lights buttons and black screen
is regonized by odin but will not accept any flash..........
help? please............ thanks in advance............
SOLVED!
Sollution:
Using the VIO youtube video upgrade to 2.3.6 content as described......
1. Make Odin ready with the rom in PDA as video describes.
2. connect tablet to computer while off and imidiatly hold down Vol Down and power button as if trying to get into Download mode, tablet will not light or show anything in screen up but computer will make USB detected sound... then press start in Odin......... it will flash the rom " P1000XWJQ8_P1000AUTJQ1_P1000XXJPZ_HOME.tar ".... follow the steps as described in VIO video EXEPT! do not let the tablet boot into android as the VIO guy says, turn it off and enter download mode and flash the 2nd file called " dbdata " and then follow his steps..... this is what i think prevented me from getting boot loop issue again................
i upgraded to the 4.1.2 by VIO also and the tablet works super! now....
i posted this to help others with THIS problem................. cheers.
Click to expand...
Click to collapse
Thanks a lot mate I have the same issue with my old tablet but I dont know if this version will work since a I have a Gt-P1000N
Exactly the same issue help me too please if possible mail me on [email protected]
Would you copy the link to the video tuts you used?
I got the same problem and I need help, would you please copy the link to the video tuts to help me? I am lost and I´m not very knoledgeable in this issue.
BMN2205 said:
to start with YES i have googled the whole internet to find a sollution to this problem.............. i have found some hints to others have THIS problem but no solution......... and flashing overcome flashin anything else for that matter using Dowload mode / recovery mode is not possible at present ( unless some one knows the solution to this specific problem ( read below please )
Hello there i got my hands on 2 used GT-P1000, the first one had 2.3.3 on it when i got it as far as i remember , i proceeded to reflash it to Android 2.3.6 following a VIO vidoe on youtube and then flashed it to android 4.1.2 also following a VIO video.... it works super and there was no problems with it......
then i got the 2nd GT-P1000 and i wanted to do the same to it..... BUT and i didnt take notice at first.... but i remembered after that this one had the stock android 2.2...........
i tryed to flash it to 2.3.6 using odin and so on like i did the previous GT-P1000........... it resultet in beeing stuck in samsung boot loop so i thought ok i have to flash it back to stock and i googlet and found a rom that i thought was the stock rom and flashed it and got PASS from odin and so on.... ( i should proberbly have done a little more homework before the 2nd flash wich was done a little in the blind ) but then i reboobet the tablet at ended up with.... ( see below )
if power button is pressed the Tablet will turn on but will ONLY light up buttons and have black screen NO other signs of life........ i can hold power button at turn it off again.
if i hold volume down button and power button to enter download mode NOTHING happens.............. it dous not turn on or do anything................
if i hold volume up and power button it just turns on and lights buttons with black screen............ nothing else
if i plug it into the charger after a couple of minutes it lights up buttons with black screen and just stays like that untill turned off...........
if i plug the tablet into usb on my computer i get the usb plugged in sound like it regonizes the tablet and Odin shows that the tablet is there...... BUT odin keeps getting stuck on " <ID:0/003> SetupConnection.. " , i tryed unplugging and then plugging the tablet in fast as some one said in a post that you can do but odin just stops and says fail........... what ever i try to flash i odin gets stuck on <ID:0/003> SetupConnection..
i have tryed 2 different versions of odin....... 1.7 and the one in the vio video i used to flash the first tablet without a hitch..............
i also tryed oneclickunbrick thing wich cant see the tablet.............
in short ...........'
Tablet cant boot any mode , just lights buttons and black screen
is regonized by odin but will not accept any flash..........
help? please............ thanks in advance............
SOLVED!
Sollution:
Using the VIO youtube video upgrade to 2.3.6 content as described......
1. Make Odin ready with the rom in PDA as video describes.
2. connect tablet to computer while off and imidiatly hold down Vol Down and power button as if trying to get into Download mode, tablet will not light or show anything in screen up but computer will make USB detected sound... then press start in Odin......... it will flash the rom " P1000XWJQ8_P1000AUTJQ1_P1000XXJPZ_HOME.tar ".... follow the steps as described in VIO video EXEPT! do not let the tablet boot into android as the VIO guy says, turn it off and enter download mode and flash the 2nd file called " dbdata " and then follow his steps..... this is what i think prevented me from getting boot loop issue again................
i upgraded to the 4.1.2 by VIO also and the tablet works super! now....
i posted this to help others with THIS problem................. cheers.
Click to expand...
Click to collapse
Hi,
First time working with a samsung phone, so im not very used to some samsung realted soft.
I'm doing a favor to a friend, he came to this problem where his phone woudnt boot up, He says one day he run out of battery and coudl never turn it on again.
when i turn it on, it gets stucked at boot image (first attached image), if i try to charge the battery image appears but with the loading logo (the loading logo is not moving), he told me that he also tried with another battery and the same appeared.
For what i've read there is a download mode besides recovery mode. I think i have no problem entering download mode (3rd pic), even though i don't know how to use it, pressing a button does nothing, and pluggin it to a pc (drivers installed it) seems the same.
So i wanted to enter recovery mode, and trying o factory reset it, but when i try to enter most of times nothing happens, the others i get weird screen like the one i attached.
I'm not pretty sure how to preceed now. The only thing that appears to be working is the download mode. If that's the case, how can i flahs the stock firmware on it?
Thanks for reading!
jisola said:
Hi,
First time working with a samsung phone, so im not very used to some samsung realted soft.
I'm doing a favor to a friend, he came to this problem where his phone woudnt boot up, He says one day he run out of battery and coudl never turn it on again.
when i turn it on, it gets stucked at boot image (first attached image), if i try to charge the battery image appears but with the loading logo (the loading logo is not moving), he told me that he also tried with another battery and the same appeared.
For what i've read there is a download mode besides recovery mode. I think i have no problem entering download mode (3rd pic), even though i don't know how to use it, pressing a button does nothing, and pluggin it to a pc (drivers installed it) seems the same.
So i wanted to enter recovery mode, and trying o factory reset it, but when i try to enter most of times nothing happens, the others i get weird screen like the one i attached.
I'm not pretty sure how to preceed now. The only thing that appears to be working is the download mode. If that's the case, how can i flahs the stock firmware on it?
Thanks for reading!
Click to expand...
Click to collapse
You would do the same thing as if it were custom firmware, goto http://www.sammobile.com/firmwares/, and download the stock firmware compatible with the device
Enter the device in download mode and flash the stock firmware with Odin
Instructions by SamMobile self:
Extract (unzip) the firmware file
Download Odin v3.09
Extract Odin zip-file
Open Odin v3.09
Reboot phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait a few minute
dolphinman310 said:
You would do the same thing as if it were custom firmware, goto http://www.sammobile.com/firmwares/, and download the stock firmware compatible with the device
Enter the device in download mode and flash the stock firmware with Odin
Instructions by SamMobile self:
Extract (unzip) the firmware file
Download Odin v3.09
Extract Odin zip-file
Open Odin v3.09
Reboot phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait a few minute
Click to expand...
Click to collapse
thanks for the reply, i think i might be doing something wrong, ODIN failed, i attach a screenshot, any idea?
I cannot tell much from the screenshot to be honest, all i can point at would be a newer version of Odin as the instructions told: [LINK TO ODIN 3.09]
dolphinman310 said:
I cannot tell much from the screenshot to be honest, all i can point at would be a newer version of Odin as the instructions told: [LINK TO ODIN 3.09]
Click to expand...
Click to collapse
Same error as before
im downloading some other firmwares to try, but i dont think there is the problem :s
I've been having this issue for months now. It does that exact thing. Try removing the SIM card and starting the phone as normal and see what happens. If it starts then, we have the exact problem. Mine works perfectly WITHOUT the SIM card but....what's a phone without a SIM card right? I've tried putting the Stock ROM on to no avail as well. I think my thread about this is still somewhere around but I doubt anyone managed to solve the problem either.
If you do work something out post it back. Sorry I couldn't be much help.
E: just posting my thread http://forum.xda-developers.com/showthread.php?t=2778167
Hello everyone,
I bought a few days ago the Honor 5C and decided to root it. So I installed the TWRP (Nemo) using "fastboot", downloaded a ZIP of SuperSU and placed at the root of the internal storage. But when I try to enter recovery mode by using "adb reboot recovery" or by pressing the Volume Up + Power buttons, the phone vibrates, displays nothing for 2-3 seconds (not even a black screen, the screen is completely off). After that the "Honor" logo is dispayed for less than a second then the screen "Your device has been unlocked and can't be trusted [...] Your device is booting now..." with no option at all.
The problem is that this screen stays forever and never displays the recovery mode screen. If I entered this mode using the physical buttons, I can just press "Power" for a few seconds and then it reboots the phone normally. But if I used "adb", each reboot makes the phone entering again the same recovery mode that doesn't work, so I use the Volume Up + Power key while the phone is connected via USB to my laptop to enter e-recovery mode, then reboot normally.
Does anyone know how to solve this problem ? I really want to root my phone but I don't know what to do for now.
Thanks by advance for your answers !
ClementNerma said:
Hello everyone,
I bought a few days ago the Honor 5C and decided to root it. So I installed the TWRP (Nemo) using "fastboot", downloaded a ZIP of SuperSU and placed at the root of the internal storage. But when I try to enter recovery mode by using "adb reboot recovery" or by pressing the Volume Up + Power buttons, the phone vibrates, displays nothing for 2-3 seconds (not even a black screen, the screen is completely off). After that the "Honor" logo is dispayed for less than a second then the screen "Your device has been unlocked and can't be trusted [...] Your device is booting now..." with no option at all.
The problem is that this screen stays forever and never displays the recovery mode screen. If I entered this mode using the physical buttons, I can just press "Power" for a few seconds and then it reboots the phone normally. But if I used "adb", each reboot makes the phone entering again the same recovery mode that doesn't work, so I use the Volume Up + Power key while the phone is connected via USB to my laptop to enter e-recovery mode, then reboot normally.
Does anyone know how to solve this problem ? I really want to root my phone but I don't know what to do for now.
Thanks by advance for your answers !
Click to expand...
Click to collapse
Are you on EMUI 5 (Android Nougat) ? If so, official TWRP is not compatible with version > EMUI 4.x for now.
I'm using EMUI 5.0 / Android 7.0.
So now I've installed an incompatible TWRP can I just downgrade to EMUI 4.0 / Android 5.0 then flash it again and root my phone or should I reflash the original recovery before doing that ? I've read somewhere that updating a rooted phone could brick it so even if mine has just a TWRP and want to downgrade instead of upgrading I prefer to be sure.
Thanks by advance !
ClementNerma said:
I'm using EMUI 5.0 / Android 7.0.
So now I've installed an incompatible TWRP can I just downgrade to EMUI 4.0 / Android 5.0 then flash it again and root my phone or should I reflash the original recovery before doing that ? I've read somewhere that updating a rooted phone could brick it so even if mine has just a TWRP and want to downgrade instead of upgrading I prefer to be sure.
Thanks by advance !
Click to expand...
Click to collapse
you need install original recovery and extract update.app from B100 firmware, then you place it to "dload" folder in your sd card and flash using 3 buttons. you cant full brick by messing with root. only soft brick which is fixable.
Ok I'll try it. I will post again if something comes wrong.
Thanks a lot for your help
I forgot to ask about one thing : I'm owning a phone with NEM-L51 model and I don't know if I can use NEM-L22 firmware ? If I can't, where can I find the right files to downgrade this specific model ? All the firmware files I see on the web are for the NEM-L22...
EDIT : I've found the B102 firmware for NEM-L51 model (Europe + UK) can I take it for the downgrade or is the B100 specific version needed ?
ClementNerma said:
Hello everyone,
I bought a few days ago the Honor 5C and decided to root it. So I installed the TWRP (Nemo) using "fastboot", downloaded a ZIP of SuperSU and placed at the root of the internal storage. But when I try to enter recovery mode by using "adb reboot recovery" or by pressing the Volume Up + Power buttons, the phone vibrates, displays nothing for 2-3 seconds (not even a black screen, the screen is completely off). After that the "Honor" logo is dispayed for less than a second then the screen "Your device has been unlocked and can't be trusted [...] Your device is booting now..." with no option at all.
The problem is that this screen stays forever and never displays the recovery mode screen. If I entered this mode using the physical buttons, I can just press "Power" for a few seconds and then it reboots the phone normally. But if I used "adb", each reboot makes the phone entering again the same recovery mode that doesn't work, so I use the Volume Up + Power key while the phone is connected via USB to my laptop to enter e-recovery mode, then reboot normally.
Does anyone know how to solve this problem ? I really want to root my phone but I don't know what to do for now.
Thanks by advance for your answers !
Click to expand...
Click to collapse
It is easy bro . When the phone shows warning logo , click volume up + power and don't leave it untill it find a vibration . Leave the buttons after 3 seconds u felt vibration
gopinaidu77 said:
It is easy bro . When the phone shows warning logo , click volume up + power and don't leave it untill it find a vibration . Leave the buttons after 3 seconds u felt vibration
Click to expand...
Click to collapse
Thanks for your help but this doesn't work. When I do what you say it goes again and again to the same warning screen which never disappears. This is really strange, when I see videos I find on YouTube all Honor 5C owners that just do what you say enter in recovery mode, but it's not my case... I really wonder why.
I don't know if that can help you to understand, but I'm using a french Honor 5C phone, with EMUI 5.0 / Android Nougat like I said previously, model is NEM-L51 and I did the Android Nougat update several days ago using the Honor's official update application, which is natively installed on the phone.
About the firmwares, I've tried the B102 version for the specific model I own but each time (I downloaded the update ZIP several times, the first one with two folders named '1-main' and '2-vendor', the second with just the 'dload' files) the update stops at 5 purcents and says "Software install failed! Incompatibility with current version. Please download the correct update package."
What can I do to solve this problem ?
ClementNerma said:
Thanks for your help but this doesn't work. When I do what you say it goes again and again to the same warning screen which never disappears.
About the firmwares, I've tried the B102 version for the specific model I own but each time (I downloaded the update ZIP several times, the first one with two folders named '1-main' and '2-vendor', the second with just the 'dload' files) the update stops at 5 purcents and says "Software install failed! Incompatibility with current version. Please download the correct update package."
What can I do to solve this problem ?
Click to expand...
Click to collapse
When u click on vol up + power in warning screen .dont leave it till it shows erecovery . Probably its 6-7 seconds
gopinaidu77 said:
When u click on vol up + power in warning screen .dont leave it till it shows erecovery . Probably its 6-7 seconds
Click to expand...
Click to collapse
When you do Volume Up + Power it attemps to enter recovery mode, not recovery (that's what I read), excepted if a USB cable is plugged in (which is not my case). And that still doesn't work.
However, I'm able to enter erecovery mode by turning on the phone with only the Power button, then holding "Volume Up" as written on the screen (there are 3 boot options that shows up, but only when I boot normally) and I enter erecovery mode. But I can't do anything interesting in this mode, just download the latest firmware (which fails at each attempt, even when I'm connected to a working WiFi point), shutdown or reboot the phone normally.
Shoud I show you a video of when I boot my phone in normal mode / recovery mode / erecovery mode ?
ClementNerma said:
When you do Volume Up + Power it attemps to enter recovery mode, not recovery (that's what I read), excepted if a USB cable is plugged in (which is not my case). And that still doesn't work.
However, I'm able to enter erecovery mode by turning on the phone with only the Power button, then holding "Volume Up" as written on the screen (there are 3 boot options that shows up, but only when I boot normally) and I enter erecovery mode. But I can't do anything interesting in this mode, just download the latest firmware (which fails at each attempt, even when I'm connected to a working WiFi point), shutdown or reboot the phone normally.
Shoud I show you a video ?
Click to expand...
Click to collapse
No i understood
gopinaidu77 said:
No i understood
Click to expand...
Click to collapse
The problem is that I can't enter recovery mode, each time I try to install an OTA or full update package from the /dload folder on the SD card it fails, so I can't downgrade at all. Do you know a link that sure points to the good update package version for the Honor 5C on EMUI 5.0 in order to downgrade to Marshmallow ? I've found several links during my searches but I don't know if the installation fails because of a phone's bug or if it fails because of an invalid version.
EDIT : I forgot to precise the long model name of my phone : NEM-L51C432B350. On Firmware Finder Rewrite it shows that there are only two update packages for it, published on 20.04.2017... So I wonder if I need to download the three files shown in the filelist of the big update (1.68 Gb) and install them on the device ?
ClementNerma said:
The problem is that I can't enter recovery mode, each time I try to install an OTA or full update package from the /dload folder on the SD card it fails, so I can't downgrade at all. Do you know a link that sure points to the good update package version for the Honor 5C on EMUI 5.0 in order to downgrade to Marshmallow ? I've found several links during my searches but I don't know if the installation fails because of a phone's bug or if it fails because of an invalid version.
Click to expand...
Click to collapse
Stock recovery wont have an option . There is no graphical UI for installation.
Downgrade or update is just a manual procedure.
In order to roll back , u need to install a roll back package and then the origional MM package . Using the three button combination
gopinaidu77 said:
Stock recovery wont have an option . There is no graphical UI for installation.
Downgrade or update is just a manual procedure.
In order to roll back , u need to install a roll back package and then the origional MM package . Using the three button combination
Click to expand...
Click to collapse
Ok but where can I find this rollback package ? I only find files for the NEM-L22 model...
EDIT : If found the Russian version from here but is it ok to take it ?
ClementNerma said:
Ok but where can I find this rollback package ? I only find files for the NEM-L22 model...
EDIT : If found the Russian version from here but is it ok to take it ?
Click to expand...
Click to collapse
Yes that's fine.
gopinaidu77 said:
Yes that's fine.
Click to expand...
Click to collapse
Ok so in the guide I found on the same page I linked in my previous post (the guide is hopefully written in english) it says that the phone must haven't been rooted or even unlocked, so I prefered to relock the bootloader (and completely reset my phone, for the third time at least in two days).
But then I realized I would need to have an unlocked bootloader for the flash so I unlocked it again, but now the device stucks on "Your device is booting now..." with no option at all whatever I do, whatever the buttons I push... I'll really start to think I'm simply idiot
I'm searching on how to solve this new problem and unbrick the phone... 'cause I can't even shutdown it, the "Volume Up + Power" combination while USB plugged in or anything else doesn't work this time.
EDIT : Okay so my phone seems to really be hard-bricked. My phone just stays at the screen "Your device is booting now..." with no option at all, I can't shutdown it, I can't enter recovery or erecovery mode. Does anyone know what to do or is my phone definitively bricked ?
ClementNerma said:
Ok so in the guide I found on the same page I linked in my previous post (the guide is hopefully written in english) it says that the phone must haven't been rooted or even unlocked, so I prefered to relock the bootloader (and completely reset my phone, for the third time at least in two days).
But then I realized I would need to have an unlocked bootloader for the flash so I unlocked it again, but now the device stucks on "Your device is booting now..." with no option at all whatever I do, whatever the buttons I push... I'll really start to think I'm simply idiot
I'm searching on how to solve this new problem and unbrick the phone... 'cause I can't even shutdown it, the "Volume Up + Power" combination while USB plugged in or anything else doesn't work this time.
EDIT : Okay so my phone seems to really be hard-bricked. My phone just stays at the screen "Your device is booting now..." with no option at all, I can't shutdown it, I can't enter recovery or erecovery mode. Does anyone know what to do or is my phone definitively bricked ?
Click to expand...
Click to collapse
Long click of power button will shut down the phone. Why u always refer about usb cable . Follow all instructions unplugged
Even the same happend for my honor 8 . Ur device isnt hard bricked .its just a soft brick
gopinaidu77 said:
Long click of power button will shut down the phone.
Even the same happend for my honor 8 . Ur device isnt hard bricked .its just a soft brick
Click to expand...
Click to collapse
Nope, long click of power button will just reboot the phone and make it displaying the same screen again and again.... I can't shutdown it at all. I've tried several times but it doesn't work :crying:
ClementNerma said:
Nope, long click of power button will hust reboot the phone and make it displaying the same screen again and again.... I can't shutdown it at all. I've tried several times but it doesn't work :crying:
Click to expand...
Click to collapse
Yes , the same happend for me ! U can unbrick bro
gopinaidu77 said:
Yes , the same happend for me ! U can unbrick bro
Click to expand...
Click to collapse
But how can I unbrick the phone ? I can't enter in any mode, I can't connect it to PC, I can't shutdown the phone, I can't use ADB or FastBoot on it, I can't reflash the bootloader or install a TWRP, downgrade or boot normally, I can't do anything !
So how could I unbrick it ? For now it's just still displaying "Your device is booting now..."
If you know how to do, please tell me so I can unbrick my phone. Sorry for asking you so many things I don't understand myself why there are so many problems...
hi there
I have problem with my phone
want to flash a custom rom on it and nothing knew about Ome lock and frp lock
wipe my phone with factory reset and now cant boot my phone because it need my google account and I forgot that my id Even cant flash custom recovery!
please help me I need my phone
On YouTube there should be a tutorial to help you, sure you find it because you only have to do a bypass.
If it says with red letters on top of the screen "FRP Lock" or something like that.
DONT BE AFRAID, i had that once and i almost thought my phone got bricked.
Steps:- 1) Press Power and Volume Down together
2) When it turns off, quickly press Volume Down, Home Button & Power together
3) It should go to download mode/odin mode
4) Go to updato.com, download your model firmware and odin
5) Flash it via odin (Put the firmware in AP) (Odin will freeze for a couple of min)
6) Start and wait
7) Done, you have a brand new phone (could possibly wipe data)
Atleast, thats what i did