I replaced all the flex cable with mic and buttons of my samsung galaxy s i9000, cause i damaged it during a display replacement.
Display now works fine but, left and right button not.
Central button also works fine.
can anyone help me to understand what is gone wrong?
Thanks
samsung GT-I9000 mic flex cable
andrea72rm said:
I replaced all the flex cable with mic and buttons of my samsung galaxy s i9000, cause i damaged it during a display replacement.
Display now works fine but, left and right button not.
Central button also works fine.
can anyone help me to understand what is gone wrong?
Thanks
Click to expand...
Click to collapse
Hello Andrea72,
What has happened if that you have torn though the flex cable going to the buttons contact pads this can only be fixed by replacing them. To do this you'll need to strip down the phone and remove the old and replace with a new one these can be found on such site like ebay, all sounds great, however to remove this part is more difficult has it's stuck down with some pretty impressive glue. I'm in the some situation as your self good luck.
Thaaquin
thaaquin said:
Hello Andrea72,
What has happened if that you have torn though the flex cable going to the buttons contact pads this can only be fixed by replacing them. To do this you'll need to strip down the phone and remove the old and replace with a new one these can be found on such site like ebay, all sounds great, however to remove this part is more difficult has it's stuck down with some pretty impressive glue. I'm in the some situation as your self good luck.
Thaaquin
Click to expand...
Click to collapse
Just a quick update i have finally received my part form china and going to attempt to replace it at the weekend, I'll try and document this and post if I am successful.
Did you manage to replace that part? My microphone is broken, so I want to replace the same part as you guys. Did you use a guide? If yes, can you post a link?
Hi
I bought that ; http://www.ebay.com/itm/LCD-Touch-D...102?pt=LH_DefaultDomain_0&hash=item4602f56036
once I installed all the pieces, I restart the cell. It starts, I can hear sound, but no image on the actual screen. What could I do wrong? Does anyone has a video? All I can find on youtube is a video of how to disassembled it but never how to change the digitizer.
Thx for ur help!
SoapShoeS said:
Hi
I bought that ; http://www.ebay.com/itm/LCD-Touch-D...102?pt=LH_DefaultDomain_0&hash=item4602f56036
once I installed all the pieces, I restart the cell. It starts, I can hear sound, but no image on the actual screen. What could I do wrong? Does anyone has a video? All I can find on youtube is a video of how to disassembled it but never how to change the digitizer.
Thx for ur help!
Click to expand...
Click to collapse
just make sure the flex cables are plugged all the way in.... if the lcd plug is just barely off it will not work...if all are plugged in it should work... there is a chance the part could be bad..(it does happen) if so just return it for another.... but the best advice is check the connections... dont force them... but unplug and replug them... anything that has to be forced is wrong and will cause damage if you force it...
no real need for a video as with the part you have shown is a pretty simple remove a few screws and unplug connections... also inspect the flex cables on the new unit... one small nick in the lcd one and it also could cause this...
hope this helps...
kawgirlval69 said:
just make sure the flex cables are plugged all the way in.... if the lcd plug is just barely off it will not work...if all are plugged in it should work... there is a chance the part could be bad..(it does happen) if so just return it for another.... but the best advice is check the connections... dont force them... but unplug and replug them... anything that has to be forced is wrong and will cause damage if you force it...
no real need for a video as with the part you have shown is a pretty simple remove a few screws and unplug connections... also inspect the flex cables on the new unit... one small nick in the lcd one and it also could cause this...
hope this helps...
Click to expand...
Click to collapse
Thx for ur help.
I tought that maybe it had something else to swap or something.
I already sent back one digitizer to the sender cauz the other one wasn't working... So my guest was that if a second one didn't work I was probably the problem but seem not...
When I reinstalled my old (and broken) screen its work like a charm.
Anyway thx for ur help I'll try to reinstall it
Moved To Q&A
Please post questions in the Q&A section
Hi guys. I recently broke my screen on my one and i order a replacement for it. I decided to do the repair myself and everything went well but when I powered on the phone after i had replaced the screen i noticed that the camera, the upper speaker and the headphone jack weren't working. They are all related to the sister board but i can't find what i have done wrong. I have already checked the connections and i flashed a new rom just in case it was a software problem. Can anyone help me with this? Is there a connector that connects all these things to the mother board?
aleaek said:
Hi guys. I recently broke my screen on my one and i order a replacement for it. I decided to do the repair myself and everything went well but when I powered on the phone after i had replaced the screen i noticed that the camera, the upper speaker and the headphone jack weren't working. They are all related to the sister board but i can't find what i have done wrong. I have already checked the connections and i flashed a new rom just in case it was a software problem. Can anyone help me with this? Is there a connector that connects all these things to the mother board?
Click to expand...
Click to collapse
before you do everything/anything see these videos first, or you can follow how to reassembly it, maybe you forget to connect cable/s
http://www.youtube.com/watch?v=yyfuBhWbhtE
http://www.youtube.com/watch?v=qZFAsgjCunc
http://www.youtube.com/watch?v=cyrxa23OwME
moha_moha20106 said:
before you do everything/anything see these videos first, or you can follow how to reassembly it, maybe you forget to connect cable/s
http://www.youtube.com/watch?v=yyfuBhWbhtE
http://www.youtube.com/watch?v=qZFAsgjCunc
http://www.youtube.com/watch?v=cyrxa23OwME
Click to expand...
Click to collapse
I have already watched these and everything seems to be in place. What is weird is that the vibrator which is a component of the sister board is working fine. I' m trying to figure out which cable connects the parts that are not working to the motherboard.
aleaek said:
I have already watched these and everything seems to be in place. What is weird is that the vibrator which is a component of the sister board is working fine. I' m trying to figure out which cable connects the parts that are not working to the motherboard.
Click to expand...
Click to collapse
the 2nd video, at 5:35 , there are 3 Flat Cables, if you connect it wrong, or cut one of them, you will found the same problems
check there cables again and any other same Flat Cables
Hi,
I really need your help as I have no idea what to do.
After 1 month of using MI5 Pro Ceramic black I have broke my phone,First the touch worked and there was only vertical lines on the lcd in the spot of the shatter so I could operate but due to my stupidity and of force touching the broken glass these vertical lines started to cover all the screen (Everything worked well on the phone..Sound,Camera and etc..)
So I ordered from Aliexpress LCD + Touch screen for about 70$ (Included DHL Express shipment)
When I got the screen I started to disassamble the phone.. Got everything out,Took out the broken screen and pasted the new screen on the frame (Must say all these aliexpress screens are really bad,0% protection on the screen,Not sure about the LCD quality yet but glass is horrible..Started to scratch even before I used it)
Anyways to our point..
Started to assamble back everything.. Powered on the phone and Yay! Phone is working but...
No Sound,Firstly I checked settings and everything..Ran CIT test and everything that belongs to audio giving force close..
Calibrate Speaker PA test results : State-Get impedance failed!,Speaker Vendor-None
Vibration- FAIL no short and no long
Main mic speaker Feedback,Simulation call test,Front mic speaker feedback test,Top mic speaker feedback test,
everything when I enter it giving FC with that details :
"IlegalStateException:Unable to retrieve AudioRecord pointer for SetParameters() blablala...
Headphone mic feedback test (Called on an uninitialized AudioRecord)
So in short..
No Speaker,No Mic,No headphone Mic..
Now my question is what I need to do from now.. Its not firmware/software problem for sure as before I disassambled the phone everything worked well..
My first guess was the problem is on the Sub PCB but then I asked my self..If the USB-C is working and WiFI antenna giving full signal it means the Sub PCB works so what the hell is the problem? I really hope its not something in the PCB it self as it means throw everything to garbage.. ;<
Hope to hear suggests..
I thought to order the MI5 32GB Black version take out the Main PCB put the Pro Main PCB and put also the ceramic back cover but that I would do only if I know that the problem is from the sub PCB but if Headphone mic doesnt work (Which the Main PCB take care of) then its probably in the Main PCB??
Please help!
you didnt damage the pins on the press connector? is the press connector on the ribbon cable flush / fully inserted ? Are you sure you didnt kink the ribbon cable?
I haven't pulled a mi5 apart, but can only assume its like every other phone i have.
leighaus said:
you didnt damage the pins on the press connector? is the press connector on the ribbon cable flush / fully inserted ? Are you sure you didnt kink the ribbon cable?
I haven't pulled a mi5 apart, but can only assume its like every other phone i have.
Click to expand...
Click to collapse
The problem is that far as I understood of how the mi5 built and from how I saw it looks like..The Speaker located in the Sub PCB cover,Vibrate connected to subPCB,And all the SubPCB connected with the cable to the main PCB and I checked it connected good and no any damaged pins from what I was able to see..If there was damaged pins then the phone wont get charged as the USB-C wont be connected as it located in the SubPCB however it does work.. So I really have no idea what cause it..
Also the Headphone mic doesnt work in the tests..Anything related to Audio giving that FC with "AudioRecord" error..
I really must to know what causing it so I will know what to do ;<
Little update,
Just connected a bluetooth speaker,No any sound nothing..
Hi everyone! My MI5 has the same problems, no sound, mic, vibration, led buttons light, plugin earphones without notification's icon, can not play music, video offline and online video (Youtube, Facebook, live stream ..). It was happened when i replaced brooken screen. The first time when I turn on, evetything ok, I can play music through speaker, but now everything has gone..! Plz tell me how to slove this problem! Sorry for my poor E!
Hi, I ended up on buying the phone again... It's impossible to fix that problem as probably you did what I did and didn't place the motherboard correctly so a little bent probably happened and that cause to the problem.
edoroom said:
Hi, I ended up on buying the phone again... It's impossible to fix that problem as probably you did what I did and didn't place the motherboard correctly so a little bent probably happened and that cause to the problem.
Click to expand...
Click to collapse
Hi there! Care to elaborate a little more? I have also the same problem. I was replacing the rear camera module while the module I had received was broken to begin with. I hadn't really figured this out initially and I tried several times to attach it and test it, perhaps move the flex and retest, and at some I remember I found out the vibration was not there, but didn't pay attention to it as everything was open, until I found out the camera module was faulty in the end, and subsequently discovered also the whole issue with sound/vibration/key backlight etc. Instead of buying a new device, I was thinking to try and fix it, but still I'm a bit unsure about what the problem really was. From what I could figure, I didn't do anything different this particular time the audio/vibration didn't work, with respect to the previous times I attached and detached the motherboard. But is it definitely the board itself and not its flex connecting it to the sub-pcb? Could it be the sub-pcb itself or even both this and the board? In case I buy a new board (perhaps together with a sub-pcb just in case) to replace it which part should I watch out for, not to damage it again. Sorry for the many questions but you seem to be the only source of info for this specific problem.
deusxx said:
Hi there! Care to elaborate a little more? I have also the same problem. I was replacing the rear camera module while the module I had received was broken to begin with. I hadn't really figured this out initially and I tried several times to attach it and test it, perhaps move the flex and retest, and at some I remember I found out the vibration was not there, but didn't pay attention to it as everything was open, until I found out the camera module was faulty in the end, and subsequently discovered also the whole issue with sound/vibration/key backlight etc. Instead of buying a new device, I was thinking to try and fix it, but still I'm a bit unsure about what the problem really was. From what I could figure, I didn't do anything different this particular time the audio/vibration didn't work, with respect to the previous times I attached and detached the motherboard. But is it definitely the board itself and not its flex connecting it to the sub-pcb? Could it be the sub-pcb itself or even both this and the board? In case I buy a new board (perhaps together with a sub-pcb just in case) to replace it which part should I watch out for, not to damage it again. Sorry for the many questions but you seem to be the only source of info for this specific problem.
Click to expand...
Click to collapse
Hi sorry for late answer,I barley visit xda these times..
After I bought the MI5 again this time in the 64gb version I tested the old 128gb motherboard (The main one) and still same problem with Vibration/Sound (While all sensors work camera too)
Which means its not the sub-pcb problem,Its the main motherboard for sure,Now what cause it?
In my opinion when I pulled of the motherboard to put it on the new screen I insert it in a bad way which made it bent a little and probably the place I bent is where the audio and all the stuff goes on..
I'm pretty sure we cant really do something about that problem as problem related to motherboard it self are usually not fixable,But if you find something I will glad to get a feedback to test on my own bad motherboard so maybe I can back to the 128gb version ;| but I doubt it..
edoroom said:
Hi sorry for late answer,I barley visit xda these times..
After I bought the MI5 again this time in the 64gb version I tested the old 128gb motherboard (The main one) and still same problem with Vibration/Sound (While all sensors work camera too)
Which means its not the sub-pcb problem,Its the main motherboard for sure,Now what cause it?
In my opinion when I pulled of the motherboard to put it on the new screen I insert it in a bad way which made it bent a little and probably the place I bent is where the audio and all the stuff goes on..
I'm pretty sure we cant really do something about that problem as problem related to motherboard it self are usually not fixable,But if you find something I will glad to get a feedback to test on my own bad motherboard so maybe I can back to the 128gb version ;| but I doubt it..
Click to expand...
Click to collapse
Many thanks for the response! It sheds a little light indeed. I also ordered another phone to replace it as the cost of the motherboard seems to be equal approximately close to a new device. I'm with you, in the same view, I also once placed the motherboard quickly in the chassis without the screw that holds it together, in one of the 50 or so attempts to try and make the camera sensor I was replacing, visible to the OS, and this looseness was the unfortunate one perhaps (?). I too don't expect the sound to work again. I just wanted to double check the issue was not with the sub-pcb, which I did thanks to you. For sure I have no hopes for the mainboard to work again, but still, what keeps me from being certain it is actually the sound card that is the problem, is a very similar case I saw In a foreign forum, and also clues from my device which support the argument that the mainboard might have entered in a kind of diagnostic boot state due to a hardware fault that was apparent, where either some components are not initialized during boot, or their HW resources are taken over from the diag. ports and irqs that are enabled, in which case the issue can perhaps be fixed. For sure whenever I find a good deal on a new motherboard I will replace it, to keep it as a secondary phone, as I liked it quite a bit, but It would be interesting to see if this hypothesis holds or not. Anyway thanks again for the response!
Hi,
I've bought used mi5 with broken screen. After LCD replacement I've found that that phone has problem with sound. Exactly the same as in this thread - no sound, mic, vibration, led buttons light, plugin earphones without notification's icon, can't play music, video offline and online video (Youtube).
Someone already did LCD replacement on this phone and probably done something.
But what I discovered on this phone that problem start when battery charge aprox more then 60%.
I did flash one year old ROM via fastboot ( just to verify if it not the ROM problem) and after that everything was fine ( battery level 50%).
I did hardware test - passed 100% fine.
But when I did charge till 100% the problem come back.
That's really interesting finding... Can you tell me the same steps you did like which rom you flashed and all of that? I will check it with my dead phone maybe if I will have the same thing like you we can point on something...
mi5 lcd replaced touch not working
I bought a mi5 mobile in singapore. My display was damaged. I changed many display in india (checked in many shop). only work display (lcd). Touch not respose. please some one give solution. thank you
have same problem with op
my phone get damaged by water so im rush turn it off and open everything then go to dry it... and problem with speaker etc doesnt work just like op please help i really doesnt have money to buy new phone this month
Exactly same problem with me, just replaced the rear camera and the problem occurs
No sound, no vibration, nav led not working at all, playing video not working
Even playing sound via bluetooth speaker not working too
I believe there is something wrong with the mainboard
can anyone point out which part of the mainboard responsible for the lower board?
The lower board works well though, I tested it using other mainboard
codearm2 said:
Exactly same problem with me, just replaced the rear camera and the problem occurs
No sound, no vibration, nav led not working at all, playing video not working
Even playing sound via bluetooth speaker not working too
I believe there is something wrong with the mainboard
can anyone point out which part of the mainboard responsible for the lower board?
The lower board works well though, I tested it using other mainboard
Click to expand...
Click to collapse
For me the problem was that after the screen replacement (It may also apply to you after you replaced the rear camera..)
When I put back he main motherboard it wasnt sat properly,I put it beneath a small plastic holder and when I closed everything and screw and all..Problem appeared and when I rechecked motherboard I found out it got bent in the right down side and that's probably what killed all the sensors,sound and everything..
Of course that what happend to me..There is plenty of other reasons that may cause to what you experience..
edoroom said:
For me the problem was that after the screen replacement (It may also apply to you after you replaced the rear camera..)
When I put back he main motherboard it wasnt sat properly,I put it beneath a small plastic holder and when I closed everything and screw and all..Problem appeared and when I rechecked motherboard I found out it got bent in the right down side and that's probably what killed all the sensors,sound and everything..
Of course that what happend to me..There is plenty of other reasons that may cause to what you experience..
Click to expand...
Click to collapse
I believe the chip or something similar, that control the sensor, led, vibration etc, was broken because we put it the wrong way
now we need to find which chip it is and replace it
which part of the right down? near the signal cable?
codearm2 said:
I believe the chip or something similar, that control the sensor, led, vibration etc, was broken because we put it the wrong way
now we need to find which chip it is and replace it
which part of the right down? near the signal cable?
Click to expand...
Click to collapse
If you just checked and saw you put it wrong as I did,On the little plastic which made a little bent then I guess you lost..I would just buy new motherboard on aliexpress or just give up and buy a new phone..
As you cant really know (I mean from our side..) if its a chip related there or if its the bent it self which made problem on the connection on the board it self..
And yes I was speaking about the right side near the signal cable where you need to install the motherboard from that side where there is a little plastic like holding the motherboard..When I did the reinstall by not checking I put the motherboard on that plastic and after I closed everything and all screws got back I discovered that problem..
edoroom said:
If you just checked and saw you put it wrong as I did,On the little plastic which made a little bent then I guess you lost..I would just buy new motherboard on aliexpress or just give up and buy a new phone..
As you cant really know (I mean from our side..) if its a chip related there or if its the bent it self which made problem on the connection on the board it self..
And yes I was speaking about the right side near the signal cable where you need to install the motherboard from that side where there is a little plastic like holding the motherboard..When I did the reinstall by not checking I put the motherboard on that plastic and after I closed everything and all screws got back I discovered that problem..
Click to expand...
Click to collapse
yeah, it means it's the same mistake as mine, that little metal thing that hold the motherboard, I forgot to eject the sim card tray and when I pull my main board it was stuck, got a little bent from there
Just wonder if anyone have the schematic for mi5 mainboard, since I'm curious and want to find a way to repair it
Not because I'm in despair of needing a phone, this MI5 is my secondary phone
Just because of the curiousity, that's all
edi--
found the schematic here
https://data.dendik.id/Data/Schematic/Xiaomi/Mi5_SM.rar
now on the journey to repair this stupid mistake, lol
any help from someone who are an expert in this thing will be really appreaciated
codearm2 said:
yeah, it means it's the same mistake as mine, that little metal thing that hold the motherboard, I forgot to eject the sim card tray and when I pull my main board it was stuck, got a little bent from there
Just wonder if anyone have the schematic for mi5 mainboard, since I'm curious and want to find a way to repair it
Not because I'm in despair of needing a phone, this MI5 is my secondary phone
Just because of the curiousity, that's all
edi--
found the schematic here
https://data.dendik.id/Data/Schematic/Xiaomi/Mi5_SM.rar
now on the journey to repair this stupid mistake, lol
any help from someone who are an expert in this thing will be really appreaciated
Click to expand...
Click to collapse
ok bruh im already do some fking around and do ic audio replacement but no hope its still broke even my repair guy who are ex xiaomi worker are give up the problem is looks like from cpu its self but there was something interesting if u try download device info hw app in google play there was warning that the device cant read sys or something cuz it was blocked and when u look at audio chipset its was gone
feel2death said:
ok bruh im already do some fking around and do ic audio replacement but no hope its still broke even my repair guy who are ex xiaomi worker are give up the problem is looks like from cpu its self but there was something interesting if u try download device info hw app in google play there was warning that the device cant read sys or something cuz it was blocked and when u look at audio chipset its was gone
Click to expand...
Click to collapse
Yeah, tried it before, and the audio chip is gone
Perhaps something wrong with the audio chip, will try to replace the IC tomorrow
This ways is for:
- When you connect the watch to the charger, it's turn on and says charging but when removing it from charger it's go black (auto poweroff)
- When you press the power button it's won't boot or go black (auto poweroff) at the "LG" screen
You need:
- Old battery
- Soldering Iron and Soldering Wire
Optional:
- 0 ohm resistance
1.Remove the sticker and plastic case on the battery protection board
Image see attachment files 1
2.Use Soldering Iron to remove the component in the image
3.Soldering 0 ohm resistance to the position of removed component or just use Soldering Wire to connect two contactor, it should be like this:
Image see attachment files 2
4.Done,now your battery should be work.
This ways is from:
tieba.baidu.com/p/4071402128 (Chinese forum, solution at the second replies)
Sorry,my English is poor and i can't find buttons to upload attachments or image to xda-developers.
I finded the buttons to upload attachment!
You can ask me if you have any other questions.
If this helped you,please click thanks button.
I will check this and will let you know if this solve my boot problem.
https://forum.xda-developers.com/g-watch-r/help/watch-shutting-removed-cradle-t3433394/page3
You are my hero of the day.
I replaced the component (what ever that may be) and the bootproblem was solved.
Thank you very much for sharing this
Do you know what the component is?
Gameboyboyboy said:
You are my hero of the day.
I replaced the component (what ever that may be) and the bootproblem was solved.
Thank you very much for sharing this
Do you know what the component is?
Click to expand...
Click to collapse
Sorry, i don't know what it is
I just found that ways from here:
tieba.baidu.com/p/4071402128 (It's a chinese forum,solution in the second replies)
It's also call it "component" , and says it's possible is a fuse
Nice post man!
I did all these steps and...... tadaaaaam BACK TO LIVE!
Mine is working to!!! Thank you very much for the solution :good:
Can someone explain what is going on here exactly? Is modifying this resistor going to make my watch potentially unsafe (eg. overcharging)? I find it really interesting that my replacement battery had the same problem as the original.
stephendt0 said:
Can someone explain what is going on here exactly? Is modifying this resistor going to make my watch potentially unsafe (eg. overcharging)? I find it really interesting that my replacement battery had the same problem as the original.
Click to expand...
Click to collapse
This may be a battery manufacturer's problem,the old "component" are broken. Just don't use charger(dock) output > 5V 1A there will not safe problem.
Excellent :good::good:
I was having this problem even after changing the new battery, I used above fix and now its working perfectly since yesterday. Thanks Again.
Hi,
I have the same issue since a few days. First of thanks for the provided solution. But because removing a potential fuse and bride the contacts doesn't sound really save to me, I want to ask if someone who has done it month ago can report that there are no issues so far.
And if someone had issues please report them, it would be much appreciated and help other people too who will find this Thread in the future.
I just wanted to say thank you!
I bridged the component with a blob of solder and half expected it to blow up in my face but it works just fine. I think I'm gonna order a new battery anyway since this one is 4 years old but this fix solved it for me!
Willy130683 said:
Hi,
I have the same issue since a few days. First of thanks for the provided solution. But because removing a potential fuse and bride the contacts doesn't sound really save to me, I want to ask if someone who has done it month ago can report that there are no issues so far.
And if someone had issues please report them, it would be much appreciated and help other people too who will find this Thread in the future.
Click to expand...
Click to collapse
If you are concerned, buy a new battery. Its cheap and quick.
A new battery has saved my G Watch R.. only 8€:good:
this also fixed my lg watch urbane that had the same issue , thanks a lot
Thank you!
Worked like a charm.
my 5 year old LG G Watch R is alive again.
Gonna order a new battery soon tho but this really did the trick
spyne82 said:
A new battery has saved my G Watch R.. only 8€:good:
Click to expand...
Click to collapse
Hi can u share the link for the 8 euro battery. Can't seem to find one nowadays
I can confirm the fix works as charm!
I really want to thank you for this amazing trick! My only hope is that whatever the piece we removed was, we don't end up with an exploding battery on our wrists! ?
Here is a Link .
It's on eBay Germany.
Between it's now for 15.99€
https://m.ebay.de/itm/Smartwatch-Ak...b1992911650a68d761747ddfff474ca&ul_noapp=true
Neveark said:
This ways is for:
- When you connect the watch to the charger, it's turn on and says charging but when removing it from charger it's go black (auto poweroff)
- When you press the power button it's won't boot or go black (auto poweroff) at the "LG" screen
You need:
- Old battery
- Soldering Iron and Soldering Wire
Optional:
- 0 ohm resistance
1.Remove the sticker and plastic case on the battery protection board
Image see attachment files 1
2.Use Soldering Iron to remove the component in the image
3.Soldering 0 ohm resistance to the position of removed component or just use Soldering Wire to connect two contactor, it should be like this:
Image see attachment files 2
4.Done,now your battery should be work.
This ways is from:
tieba.baidu.com/p/4071402128 (Chinese forum, solution at the second replies)
Sorry,my English is poor and i can't find buttons to upload attachments or image to xda-developers.
I finded the buttons to upload attachment!
You can ask me if you have any other questions.
If this helped you,please click thanks button.
Click to expand...
Click to collapse
Thank you for this instructions, i was able to fix my g watch r and get it back to working. I didn't use it for quite a while, and when i wanted to use it again it started to only work when charging (similar to my lg g3 when the battery is almost dead, which i fix with a new one, second replacement).
And i decided to give this a try before buying a new battery, my thought was that i had nothing to lose... First attempt aasn't perfect, i was able to remove that little chip, but the soldering didn't went very well (i am not very talented with a sodering iron) and when i reassembled the watch it started to flash a empty battery icon and didn't charged or turned on.
So i tryed a second time and the sordering ended up much better the second time. The 2 connectors ended well connected this time and it is now working normally.
It was very helpfull and it worked much better than i expected.