nexus one "radio v2 - fail-pu" help needed - Nexus One Q&A, Help & Troubleshooting

Hi all,
I need help to install any rom or something else with my nexus one.
I have attached picture.
When I starting the device I get 7 vibrations but I can see the fastboot screen.
I have tried to put passdiag file on the sd card and this is what I can get.
i have AT&T device with AMOLED
and also S-ON (so i cannt run adb).
Thanks Yaron.

You meant PASSIMG and not PASSDIAG. But it doesn't matter much. Unfortunately, your Nexus One is dead.
"Fail-PU" means "Failed Partition Update", which means - your NAND chip died and can't be recovered. Since it died on Radio partition, you can't do anything with it.
Time to move to a better phone, I guess.

Exact problem.. very precise
Jack_R1 said:
You meant PASSIMG and not PASSDIAG. But it doesn't matter much. Unfortunately, your Nexus One is dead.
"Fail-PU" means "Failed Partition Update", which means - your NAND chip died and can't be recovered. Since it died on Radio partition, you can't do anything with it.
Time to move to a better phone, I guess.
Click to expand...
Click to collapse
yrone said:
Hi all,
I need help to install any rom or something else with my nexus one.
I have attached picture.
When I starting the device I get 7 vibrations but I can see the fastboot screen.
I have tried to put passdiag file on the sd card and this is what I can get.
i have AT&T device with AMOLED
and also S-ON (so i cannt run adb).
Thanks Yaron.
Click to expand...
Click to collapse
same problem all hboot radio versions are same as well... very exact .. did you solve it yet.. if so can you tell me how to solve it.. i can actually get into fastboot.. thats all i can say now.. can you help me solve ths problm..
and my nexus one stuck with boot screen..

And I thought my reply explains the situation very well...
Read it again, several times, until you understand the meaning of "dead phone".

Jack_R1 said:
And I thought my reply explains the situation very well...
Read it again, several times, until you understand the meaning of "dead phone".
Click to expand...
Click to collapse
yea i understood. still i can just change that logic board by buying some old used working parts from ebay.
i think that will work.. :laugh: :cyclops:

Yes, you can, of course. But this is the main board with the CPU, it might cost almost as much as a complete N1.

Related

Help me unbrick my phone

So i just updated to an SPL for a Hero ROM, and now i'm stuck on the t-mobile G1 screen, i can get to the console, but if someone can walk me through how to mount the SD card using ADB (from the very begining) it would be a great help. This way i can try to update the firmware, or resort back to the original radio/spl/firmware. I need a very easy to understand set of instructions, because every time i have tried to do something with ADB it never goes well.
all you need to do is re-flash your current rom your using no wipe needed.
Whats the command to do that, i've been trying to load the new ROM onto the SD card through the command prompt. and it doesn't seem to want to work.
Bassicly i use the adb push command to try and shove a ROM on to the SD card like this
adb push JAChero2.0r6.zip /sdcard/JACHero2.0r6.zip
and then i change the name to update.zip and it still applies the OLD SPL update.zip file i have in there.
Try removing the old update file first through the adb shell. I have run into a couple instances where it is doing what you are describing. I always found that removing the current file first will resolve it.
adb shell
# rm /sdcard/update.zip
# exit
adb push JAChero2.0r6.zip /sdcard/update.zip
Then try to flash the update through recovery.
Got it fixed, THANKS!
im stuck at g1 screen as well....what did you do to fix this?
Im stuck on G1 boot screen, cannot get into FBOOT or anything!
What can I do??
if none of the button combos work like home+power or camera+power or any others then you can either call tmobile and play dumb or have the sweetest paperweight at the office.
crpercodani said:
if none of the button combos work like home+power or camera+power or any others then you can either call tmobile and play dumb or have the sweetest paperweight at the office.
Click to expand...
Click to collapse
Will it cost me if I contact tmo?
I'll play it dumb, but when the phone ends up at some engineer, and they see what I've flashed on, will they just fix it, or report it to tmo? (as i've broken the t&c's!)
As much as having a paperweight sounds cool, I could really do with a phone!
BTW, thanks for your help!
IanVaughan said:
Will it cost me if I contact tmo?
I'll play it dumb, but when the phone ends up at some engineer, and they see what I've flashed on, will they just fix it, or report it to tmo? (as i've broken the t&c's!)
As much as having a paperweight sounds cool, I could really do with a phone!
BTW, thanks for your help!
Click to expand...
Click to collapse
If the phone won't boot using home + camera then they can't prove it's been rooted (unless they somehow read the nand...) so they should replace it for you without charge.. Same thing could happen if the battery was pulled during an over-the-air update.
they wont bother checking anything, just be sure it is bricked and your good. Most likely they just take it apart and jtag it or something like that. And if you got the phone from tmo and are with them then no its free.
AdrianK said:
If the phone won't boot using home + camera then they can't prove it's been rooted (unless they somehow read the nand...) so they should replace it for you without charge.. Same thing could happen if the battery was pulled during an over-the-air update.
Click to expand...
Click to collapse
crpercodani said:
they wont bother checking anything, just be sure it is bricked and your good. Most likely they just take it apart and jtag it or something like that. And if you got the phone from tmo and are with them then no its free.
Click to expand...
Click to collapse
Yep, it wont boot using any key-combo.
Its reading the NAND/using JTAG which is what I'd do (i work with embedded devices!).
I might say the battery died while the update was happening, gotta act dumb! (which I must be for managing to brick it in anycase, after all, Im a softy-eng!)
And I'll get a new phone! Or reconditioned?
Many thanks ppl!
Well.
If you manage to help this guy (http://twitter.com/r3nrutSite/) and the ppl on this thread (http://forum.xda-developers.com/showthread.php?t=309291) to JTAG the G1, please tell me.
I'm stuck with a bricked G1 here in Brazil.
Currently there is no way of bringin a g1 back to life short of giving it a heart transplant<new board>
see Brick Thread
Tp2 brick eny help??????
plis help
i was unlocking my phone (the HTC Touch Pro 2 <sprint>) and I was using a Diamond unlocker , but during the process there was a connection error and now my phone seems to be bricked. I can't get it to even turn on, get to a bootloader screen, or anything even remotely close.
The one odd thing that it does though, is when I connect it to my computer, it pops up and my computer recognizes there is a device there. In my Device Manager there is an unknown device called: Qualcomm CDMA Technologies MSM. I have tried every combination of two buttons, including holding down the reset button with all of them, but nothing gets me anywhere.
If anyone could help, I would really appreciate it. there's eny way to save it???
SHADE86 said:
plis help
i was unlocking my phone (the HTC Touch Pro 2 <sprint>) and I was using a Diamond unlocker , but during the process there was a connection error and now my phone seems to be bricked. I can't get it to even turn on, get to a bootloader screen, or anything even remotely close.
The one odd thing that it does though, is when I connect it to my computer, it pops up and my computer recognizes there is a device there. In my Device Manager there is an unknown device called: Qualcomm CDMA Technologies MSM. I have tried every combination of two buttons, including holding down the reset button with all of them, but nothing gets me anywhere.
If anyone could help, I would really appreciate it. there's eny way to save it???
Click to expand...
Click to collapse
Theres a app for that!
an app for recovery a htc tp2 brick
Ace42 said:
Theres a app for that!
Click to expand...
Click to collapse
really an app??
please tell me where i can find it
and what steps i must follow,
am desperatedm thank`s
SHADE86 said:
really an app??
please tell me where i can find it
and what steps i must follow,
am desperatedm thank`s
Click to expand...
Click to collapse
http://tinyurl.com/yayoq48
App used: Firefox

DREAIMG.nbh does not load...

I am unable to root my G1 at all. I can not get it to load any of the "root" files. It is a PVT board. Everytime I go to load the DREAIMG.nbh, it just does nothing.
Anyone got suggestions? I need to be able to flash the custom roms. It is a T-Mobile model. I have tried multiple SD cards already. I am getting a bit annoyed.
I do a lot of stuff with the Tilt and Android personally. This is seriously baffling me.
Thanks for any help.
try redownloading the img
are the sdcards class 6?
are u getting into bootloader mode correctly (camera + power)
what are you currently running?
more details
Try to use the guide in my sig. Its much quicker
As said above, more details are needed.
Try redownloading the file, and copying it over to the SD card again. If you are using the USB cable that came with the Dream, be aware that every one I've seen does NOT have a ferrite bead on it. This causes problems and can corrupt the file.
If you know how, md5sum the file on your PC and after copying it.
Does any error come up in the bootloader when you try flashing it?
K, I am using a DREA100
I did not use a usb cable (used a sd card reader)
I get "image not found" or something to that nature in the boot loader then it goes to strips.
I have dealt with HTC for a LONG time...I have been doing it since the Apache. I never could get this to work.
Yes I am using Class 6 cards. I do IT development and I need the speed.
I will try the suggested guide.
Thanks for all the help. I didn't realize there was an easier route. Also I was actually going to message you david, but I didn't want to feel like a complete noob haha.Thanks again.
natalic said:
Thanks for all the help. I didn't realize there was an easier route. Also I was actually going to message you david, but I didn't want to feel like a complete noob haha.Thanks again.
Click to expand...
Click to collapse
You might want to also check the spelling. It sounds silly, but you'd be surprised, I've done it myself.
BlackElvis79 said:
You might want to also check the spelling. It sounds silly, but you'd be surprised, I've done it myself.
Click to expand...
Click to collapse
I even tried the kit thing, but in the end, nothing beats an easy APK. As I said, I do a lot of work with the kaiser. This was not NEW to me, but the G1 is not known territory for me.

32b Bricked?

Hey guys,
i have a big problem,
my htc magic 32b was jerking me,
it lost the signal to network,
so i decided to make a radio update,
i used this:
http://forum.xda-developers.com/showthread.php?t=640535
now, i can't enter fastboot and it doesn't boot (only vodafone screen)
What can i do now??
plz help me
This is the HTC Dream aka G1 forum. You're looking for the HTC Magic forum.
Nonetheless, if you can't boot the phone into recovery or fastboot, then you're pretty much hosed. I'm actually trying to unbrick a G1 right now, I can't even get into fastboot/bootloader to try and reflash the phone. Really sucks for me because I had just flashed a G1 the night before and it was flawless. Same directions, different results
freakingwilly said:
This is the HTC Dream aka G1 forum. You're looking for the HTC Magic forum.
Nonetheless, if you can't boot the phone into recovery or fastboot, then you're pretty much hosed. I'm actually trying to unbrick a G1 right now, I can't even get into fastboot/bootloader to try and reflash the phone. Really sucks for me because I had just flashed a G1 the night before and it was flawless. Same directions, different results
Click to expand...
Click to collapse
Many myTouch users actually live here. 99% of users in the Sapphire section are 32A so any 32B problems will be better answered here.
However, yes you are bricked as freakingwilly said. Just off of a radio is quite funny, though. My only thought is that you got hold of a bad one and flashed it.
r3s-rt said:
Many myTouch users actually live here. 99% of users in the Sapphire section are 32A so any 32B problems will be better answered here.
However, yes you are bricked as freakingwilly said. Just off of a radio is quite funny, though. My only thought is that you got hold of a bad one and flashed it.
Click to expand...
Click to collapse
I didn't know that the Dream forum was home to the Sapphire users.
If I recall correctly, the boot order is RADIO > FASTBOOT > SPL. So if the radio is hosed, there won't be any real way to flash anything else (unless you use a JTAG, but that's a little more advanced than what the OP is looking for).
thx for the quick answers,
is there any possibility to debrick my phone?
i can't realise a brick in case of a radio update!!!
best regards,
depressed psycho
psycho_nr_1 said:
thx for the quick answers,
is there any possibility to debrick my phone?
i can't realise a brick in case of a radio update!!!
best regards,
depressed psycho
Click to expand...
Click to collapse
Well, like I said, it was only if memory is serving me correctly that the boot order is indeed RADIO > FASTBOOT > SPL. The only way you'd be able to fix a SOFT brick is if you were able to boot into fastboot/bootloader (Camera + End Call) or recovery mode (Home + End Call). From recovery, you could just reflash the radio or roll back to a radio that works. If that didn't work, you'd boot into bootloader, reflash the OEM NBH file, and start fresh. You lose all your data, but you don't lose a phone.
Unfortunately, you
There might be one option left... turn on your phone and connect it to your computer. If your computer recognizes the device, then you can use ADB to push a working radio to the phone.
freakingwilly said:
Well, like I said, it was only if memory is serving me correctly that the boot order is indeed RADIO > FASTBOOT > SPL. The only way you'd be able to fix a SOFT brick is if you were able to boot into fastboot/bootloader (Camera + End Call) or recovery mode (Home + End Call). From recovery, you could just reflash the radio or roll back to a radio that works. If that didn't work, you'd boot into bootloader, reflash the OEM NBH file, and start fresh. You lose all your data, but you don't lose a phone.
Unfortunately, you
There might be one option left... turn on your phone and connect it to your computer. If your computer recognizes the device, then you can use ADB to push a working radio to the phone.
Click to expand...
Click to collapse
As for your other comment, Sapphires come in 32b and 32a. Most 32b users dwell here.
As for bolded, some people have had luck issuing a fastboot command and leaving it sitting all night only to find it to be successful in the morning. You'll get a "Waiting for device...." for a loooong time and there's no assurance this will work at all and chances are slim to none.
Of course, you can send it in for warranty or buy another G1 with like a cracked screen or in real rough condition and replace what ever's broke from your old G1.
sounds like i'm realy ****ed up with my phone =(
hmm... i try something, if doesn't work the only way will be a new one i think...
i'm realy pissed off about this radio update, but it is how it is..
Thx for your answers and tips.
best regards
psycho
hey guys something new...
try to boot....
nothing... connect it to the computer...
klicked on "boot modified recovery" and *tada* its in recovery... and this w/o fastboot..
i try to wipe, old radio, wipe, new rom, we'll se if it's fixed afterwards
psycho_nr_1 said:
hey guys something new...
try to boot....
nothing... connect it to the computer...
klicked on "boot modified recovery" and *tada* its in recovery... and this w/o fastboot..
i try to wipe, old radio, wipe, new rom, we'll se if it's fixed afterwards
Click to expand...
Click to collapse
Hi, glad to hear you had success!
Exactly what did you do to achieve this, step-by-step?
startup and boot modified recovery
first computer found not device,
but i saved the nand back up files on root of sd,
booted device, also only vodafone screen,
but now i came in recovery, w/o fastboot.
My only prob. is now,
my sim don't connect to network -.-
this phone is jerking me....
and idk what to do =(
someone know how to fix?!
best regards,
psycho
This actually great news for you. The reason your SIM won't connect to the network is because the radio you flashed to the phone is not designed for your phone, which resulted in the "soft brick" you were experiencing before.
All you have to do is flash the correct radio for your phone through the recovery mode and you should be back in running condition.
Would you mind sharing how you got to the "boot modified recovery?" I am sure this will help people unbrick their devices as well.
i can't find an old radio =( can someone give me a link?
i've posted the way in another thread about a bricked g1
but i tell you again
i've tried all, i found...
but aber a few nights spending to my phone,
i found this:
1. copy your nand backup to root of your SD
2. Start you phone (should only boot, till vodafone screen)
3. Connect phone to computer (message: device not known)
4. Boot modified recovery with Z3kos recovery helper.batch
5. Wipe
6. Flash old Radio (DO NOT WIPE AFTER THIS)
7. Flash Rom
STOP FLASHING RADIOS. You need to FASTBOOT them. Please, if you're going to root, indulge yourself in the knowledge.
http://fwd4.me/Ur5
There is the newest radio. Now fastboot it.
i'm not a rooting noob!
and this is first time, something like this happen to me^^
psycho_nr_1 said:
i'm not a rooting noob!
and this is first time, something like this happen to me^^
Click to expand...
Click to collapse
obviously you are considering it even happened.
r3s-rt said:
STOP FLASHING RADIOS. You need to FASTBOOT them. Please, if you're going to root, indulge yourself in the knowledge.
http://fwd4.me/Ur5
There is the newest radio. Now fastboot it.
Click to expand...
Click to collapse
And if you are going to help, indulge yourself in the OP's post.
psycho_nr_1 said:
*OP shortened*... now, i can't enter fastboot and it doesn't boot (only vodafone screen)...
Click to expand...
Click to collapse
If you read the OP's post, you would have known that the OP cannot get into fastboot. So telling the OP to do something that they cannot do doesn't help.
r3s-rt said:
obviously you are considering it even happened.
Click to expand...
Click to collapse
If you don't have anything nice to say, don't say anything at all.
freakingwilly said:
And if you are going to help, indulge yourself in the OP's post.
If you read the OP's post, you would have known that the OP cannot get into fastboot. So telling the OP to do something that they cannot do doesn't help.
If you don't have anything nice to say, don't say anything at all.
Click to expand...
Click to collapse
and you should RTFT, OP now has a working phone but with no data connectivity. so he can now access fastboot. r3s-rt was telling OP to not flash the radio next time, fastboot it.
jamesd86 said:
and you should RTFT, OP now has a working phone but with no data connectivity. so he can now access fastboot. r3s-rt was telling OP to not flash the radio next time, fastboot it.
Click to expand...
Click to collapse
Wow, I suck. And I REPLIED to OP having a working phone.
*hangs head in shame* Excuse me while I walk in the other direction.
jamesd86 said:
and you should RTFT, OP now has a working phone but with no data connectivity. so he can now access fastboot. r3s-rt was telling OP to not flash the radio next time, fastboot it.
Click to expand...
Click to collapse
...10 char.

[Q] G1 stuck at "G1 T-Mobile" Startup screen. How to fix?

Hello,
Tryed to find similar threads, but found none with the correct answer.
When i tryed to unroot/unflash my phone back to stock something went wrong.
Now when i try to turn my phone on i can only see this "G1 t-Mobile" loadingscreen and nothing else happens.
Ive tryed booting with Home+Power, with Camera+Power and a normal booth, nothing works. Replaced the SD-card with an other one (1GB), first formatted FAT32style, didnt work. Afterwards i put the DREAIMG.nbh file on it and tryed it, but still didnt work. Im all out of options.
Can someone please help?
hoipupe said:
Hello,
Tryed to find similar threads, but found none with the correct answer.
When i tryed to unroot/unflash my phone back to stock something went wrong.
Now when i try to turn my phone on i can only see this "G1 t-Mobile" loadingscreen and nothing else happens.
Ive tryed booting with Home+Power, with Camera+Power and a normal booth, nothing works. Replaced the SD-card with an other one (1GB), first formatted FAT32style, didnt work. Afterwards i put the DREAIMG.nbh file on it and tryed it, but still didnt work. Im all out of options.
Can someone please help?
Click to expand...
Click to collapse
I'm afraid you have a hard bricked phone. Only way out is to jtag it.
http://forum.xda-developers.com/showthread.php?t=591048
i have the same problem in my g1 mobile he is dead now please help me
Did you try going to the Root screen? If you can't go to the root screen, then it might be Bricked, I'm not sure though.
Sent from my T-Mobile G1 using XDA App
I have tryed every button combination possible, and none of them worked
So there is no other way to fix this unless i need to adjust the hardware?
hoipupe said:
I have tryed every button combination possible, and none of them worked
So there is no other way to fix this unless i need to adjust the hardware?
Click to expand...
Click to collapse
I'll simply refer you back to post number 2.
shadowch31 said:
I'll simply refer you back to post number 2.
Click to expand...
Click to collapse
Yes, and thank you for that.
Though, im afraid i'm not competent enough to "JTAG" it as i dont understand 50% of the stuff being said in that post
Also i read you need some equipment like a JTAG Adapter, which i dont have..
hoipupe said:
Yes, and thank you for that.
Though, im afraid i'm not competent enough to "JTAG" it as i dont understand 50% of the stuff being said in that post
Also i read you need some equipment like a JTAG Adapter, which i dont have..
Click to expand...
Click to collapse
Your best bet would be to see if anyone in your area/country who can do it for you probably at a lot cheaper cost than buying a new phone.

bionic ... new chalange

Ok guys ... this is the problem ...:crying:
I have (had) a Droid Bionic running ics leak 232 in Brazil (GSM/UMTS ... thanks to xda developers - "bionic in t mobile" thread).
While messing around with the phone connected to linux (baaad idea) at some point I deleted the bootloader ("happy finger" + lack of knowledge os linux).
Now, my phone doesnt power up and RSD Lite doesnt recognize it when connected but, when I connect it to the PC, a green light lits at the top right corner of the phone and Windows recognize it, at the device manager, as a OMAP4430 USB under TI Board tab. This leads me to think that some kind of life still exists down there or, the hardware is alive and waiting for the right software.
After a long quest for a solution, I found this: "forum.gsmhosting.com/vbb/f634/unbrick-dead-samsung-gt-i9250-galaxy-nexus-gt-i9100g-via-usb-cable-freeeeeeeeeeee-1465412/index9.html".
Now I think this is the way out of this mess (is the same hardware, OMAP platform from Texas Instrument), if exists any, but this was made for Samsung, by Samsung technicians, and doesnt apply to Motorola. :crying: again.
So, is there anyone who can help me, or have any idea of what can be done (other than trow it away or use it as a paper weight)?
Any help would be most appreciated.
Regards
I saw you haven't had any replies yet. My roommate had a similar problem, he managed to mount his system partition automatically and thought his SD card was partitioned into 10 or more partitions.
So he reformated the mount and had a dead phone right after, said he only got a small white light on his notification light when plugged in.
I didn't get a chance to check it out before he took it to Verizon for a refurb, so sadly I'm not much help. Just thought I'd input anything I knew since you still had an empty thread. Hope it comes back alive!
Sent from my kitchen toaster.
Have you tried using the command line version of moto-fastboot? It might work, but might not work... I think you need to boot into fastboot mode, but I could be wrong... Either way it's worth a try.
Also, does anything happen when you try to hold down the vol+ and VOL- buttons when powering on the phone?
Sent from my XT894 running ICS
its dead
danifunker said:
Have you tried using the command line version of moto-fastboot? It might work, but might not work... I think you need to boot into fastboot mode, but I could be wrong... Either way it's worth a try.
Also, does anything happen when you try to hold down the vol+ and VOL- buttons when powering on the phone?
Sent from my XT894 running ICS
Click to expand...
Click to collapse
Thank you for your answer danifunker;
The phone is dead. Pressing buttons does nothing. The only thing that happens is to lit the notification green light at the top right corner of the screen WHEN a plug it in my PC and windows keep telling me this is a unknown device. I unsuccessfully used OMAPFlash, but installing the usb drives that came with it, when I plug it to the PC, windows device manager shows me a new device "OMAP4430 USB" under a new tab "TI Board" , whitch is not recognized by RDS lite or adb or fastboot. Is only recognized by OMAPFlash. If you dont know about OMAPFlash, I found it here http://forum.xda-developers.com/showthread.php?t=1701471 , but this procedure is for a Samsung, witch uses the same platform (OMAP4430), but I dont have the right configurations for the Droid Bionic.
Just the same
chrisp6825 said:
I saw you haven't had any replies yet. My roommate had a similar problem, he managed to mount his system partition automatically and thought his SD card was partitioned into 10 or more partitions.
So he reformated the mount and had a dead phone right after, said he only got a small white light on his notification light when plugged in.
I didn't get a chance to check it out before he took it to Verizon for a refurb, so sadly I'm not much help. Just thought I'd input anything I knew since you still had an empty thread. Hope it comes back alive!
Sent from my kitchen toaster.
Click to expand...
Click to collapse
Thank you for your interest.
If you have any further notice about your roommate problem, please let me know.
And, if you manage to post a reply from your kitche toaster, I am sure you will be able to help in this problem. looking forward for that. :laugh:
pjcw said:
Thank you for your interest.
If you have any further notice about your roommate problem, please let me know.
And, if you manage to post a reply from your kitche toaster, I am sure you will be able to help in this problem. looking forward for that. :laugh:
Click to expand...
Click to collapse
Can you explain exactly how you deleted the bootloader off of the Bionic? Knowing EXACTLY (what you ran, what you typed) what you did will help us help you.
As an aside, I had no idea there was a SGSII-OMAP variant, but I am not big on the Samsung phones, just assumed they've only been using their own SoCs for a while now...
Hi podspi.
Sorry for the delay.
As a matter of fact, wasnt me that bricked the phone. A friend o mine tryed to flash a gelly beam version, and did it via Fastboot,, under Linux (of witch I know almost notingh).
He told me that the problem was that he made:
fastboot erase mbm
and then
fastboot reboot bootloader
and so the bootloader was lost. He missed a step.
Any help will be greatly aprecieted.
Regards
IOW, since the mbm has been erased, and the mbmflashable hasn't been flashed, there is no way to get it into the bootmenu sceen anymore, right?
Hmmm. Let me ask some other folks too.
Sent from my ASUS Transformer Infinity Running Tapatalk.
I wonder if a factory cable would work to get it to flash mode? Why would you even mess with the bootloader trying to install ICS? You do that through recovery, not fastboot.
I was on ICS ... This was an attempt to get it to JellyBeen ... I, also, dont know why. I was perfectly happy with ICS working in GSM/WCDMA. This is why I am so sad ... It was a very stupid thing to do ... As a matter of fact, I will get a factory cable, but I dont think this is gonna help. Anyways, I am keeping it by side to remember me not to mess with things that are working fine. I'm kind of losing hope that it can fixed.
Regards
pjcw said:
I was on ICS ... This was an attempt to get it to JellyBeen ... I, also, dont know why. I was perfectly happy with ICS working in GSM/WCDMA. This is why I am so sad ... It was a very stupid thing to do ... As a matter of fact, I will get a factory cable, but I dont think this is gonna help. Anyways, I am keeping it by side to remember me not to mess with things that are working fine. I'm kind of losing hope that it can fixed.
Regards
Click to expand...
Click to collapse
I think we need to figure out how you flash mbm back onto there. Actually, I think it's mbmloader that you need on there...
mbm = Motorola Boot Manager (?) maybe.
After reading this page: http://omappedia.org/wiki/Bootloader_Project
I believe, mbm = uboot, mbmloader = x-loader
Just found this page... http://www.droid-developers.org/wiki/How_to_load_mbmloader_from_SD_card
download the SBF and grab the mbmloader for ICS. See if you can get a little further...
SamuriHL sHouse of Bionic restored mine when all I could get was fastboot.
Sent from my DROID BIONIC using xda premium
It won't help this. It needs to be flashed at the omap level and since moto isn't about to release the configuration files for the Bionic you can consider this one permanently bricked.
Sent from my Xoom using Tapatalk 2
I tend to agree with SamuriHL. I was thinking that the configuration souldn't be so diferent than others (like Samsung) that uses the same platform (omap). I know that it's naive, but what else could I do. Also, I need the signed files for x-loader and u-boot, of witch I think danifunker is right, this means mbm and mbmloader, that I have, but they came in bin format and not image format (.img). I will try to convert them to .img, but I am at the end of my resources (not that they are so many), and will give up shortly. At this point (giving up), I will buy another cellphone AND IT WONT BE A MOTOROLA, Probably a HTC or a Samsung. But I will keep Bionic at my desktop, as a paperweight, to remind me how I liked it, how I mess things up.
Anyways, if I manage to solve this problem, I will post here, and I wish to thank everyone that spare their time to try to help people. If anyone have any suggestion, I'll be glad to follow.
If you modify them in any way they'll no longer be signed and won't work. Someone else already went through several weeks of trying to fix their phone that had similar issues. He's well connected and still couldn't get the necessary files. Don't necessarily give up on Moto, though...it's not their fault we're stuck with locked bootloaders. Blame VZW for that one. Even Samsung was forced to lock the S3 on VZW. Things may change some day. We'll have to wait and see.
You can always get RAZR i with the unlockable bootloader! that might make things a bit easier...
IT'S DONE!!!!!!!!!
IT'S DONE ....... IT IS ALIVE AGAIN :highfive:
Guys. My phone is alive again. Thanks to FRAGULINA and PICGRABBER for their unvaluable help. It is now running GSM with data enabled (3G) with ICS 232, rooted, thanks to FRAGULINA and HTCFlyerX ( http://forum.xda-developers.com/showthread.php?p=31101192&highlight=build+prop#post31101192).
Well, I'm attaching 2 zip files. One is omapflash and the other is "THE FILES", and instructions on the "release_notes.txt". This works on LINUX.
And works like a charm. Took me (much) less than 5 minutes to get me from a dead phone to bootloader fastboot. And the rest is history. Well known procedures.
Thanks to all of you that helped or tryed to help.
Enjoy.
To those who have an interest in new challanges (as I know you are), i'm opening a new quest and would appreciate your thoughts.
I have at hand an atrix 2 and I want to find where in hell is the subsidy code writen at and how can I read it. This new quest will be at the proper location at the atrix 2 forum.
I think we won this challange. Lets go for another.
Any doubts I am available to help.
Regards.
Holy.....uh, well, WOW! I'm in awe here on this one. WELL DONE!!!!!!!
SamuriHL said:
Holy.....uh, well, WOW! I'm in awe here on this one. WELL DONE!!!!!!!
Click to expand...
Click to collapse
Can we use this method to flash any firmware to the phone? Lets say you load the latest ICS, maybe we use this method which restores the most original bootloader to the phone and then flash to any version?
Which version did you fastboot to?
pjcw said:
IT'S DONE ....... IT IS ALIVE AGAIN :highfive:
Guys. My phone is alive again. Thanks to FRAGULINA and PICGRABBER for their unvaluable help. It is now running GSM with data enabled (3G) with ICS 232, rooted, thanks to FRAGULINA and HTCFlyerX ( http://forum.xda-developers.com/showthread.php?p=31101192&highlight=build+prop#post31101192).
Well, I'm attaching 2 zip files. One is omapflash and the other is "THE FILES", and instructions on the "release_notes.txt". This works on LINUX.
And works like a charm. Took me (much) less than 5 minutes to get me from a dead phone to bootloader fastboot. And the rest is history. Well known procedures.
Thanks to all of you that helped or tryed to help.
Enjoy.
To those who have an interest in new challanges (as I know you are), i'm opening a new quest and would appreciate your thoughts.
I have at hand an atrix 2 and I want to find where in hell is the subsidy code writen at and how can I read it. This new quest will be at the proper location at the atrix 2 forum.
I think we won this challange. Lets go for another.
Any doubts I am available to help.
Regards.
Click to expand...
Click to collapse
This is unbelievable. After talking with you on Gtalk, I thought this was a permanent brick. Thanks for the files...I have a guy on gtalk right now who can benefit from these.

Categories

Resources