Hi guys
As i was searching on the forum, It didnt match my problem at all.
Problem:
I recently replaced my screen with a digitizer, It worked for like a couple of hours, and then it just stopped working.
When I opened my phone, I was doing everything very carefully, so I did not broke any parts of my phone..
Is there any way to get it back to work?
P.S Im not running a custom ROM, just the stock samsung ROM.
Sincerely
Dylano
Illumnia said:
Hi guys
As i was searching on the forum, It didnt match my problem at all.
Problem:
I recently replaced my screen with a digitizer, It worked for like a couple of hours, and then it just stopped working.
When I opened my phone, I was doing everything very carefully, so I did not broke any parts of my phone..
Is there any way to get it back to work?
P.S Im not running a custom ROM, just the stock samsung ROM.
Sincerely
Dylano
Click to expand...
Click to collapse
Did you properly connect it? could've come loose when walking around
Related
Hey guys,
I've had my X1i for a year now. No hard falls most falls are on soft surfaces. & Suddenly today morning woke up & the touch screen isn't responding. So I looked up posts, some said turn it off & turn it back along with removing the battery & it should work fine. Tried that, worked for a bit then stopped working again. Also tried soft-reseting & gave the same result. So is there any other method you guys know ? I'm thinking the other type of reseting..forgot what it's called but that'll delete everything so i gotta back things up first. So any solutions? & thanks in advance.
Have you got a screen protector on it? If so, try lifting the edges of it a little.
Nope, no screen protector. Does it have to do with any .cabs i've installed before ? Or they're not related? Is the battery related? Could it cause something like that?
I once run into the following, it may help you too:
after installing an app(from a cab) my screen was allmost non responsive.
Calibration didn't help.
I have "Advannced config" installed, uppon checkin the sensitivity it was waaaaay down, even under default.
Hope it helps for you too =)
i had the same problem to on my proto x1
it completely stopped working and i tried everything (reflash rom, boot android)
but all without luck so i bought a replacement screen
after a while my touch screen started working again but still occasionally fails
i have not yet replaced my touchscreen, i am thinking about a loose connector or something...
btw i was on official r3 fw
your flex cable might have worn out!
Jonny4911 said:
your flex cable might have worn out!
Click to expand...
Click to collapse
Where is that located? Where can I get a new one?
kyuubikitsuni said:
Where is that located? Where can I get a new one?
Click to expand...
Click to collapse
here is one thread about it, there should be others if you search some more than I did
and this would be a means to get a new one (official site, similar price), if it really is the cause and you don't like to tinker
cheers and gl
If your LCD is working, then it could be bad digitizer like mine instead of the ribbon cable. (Well, I use X1 a lot in humid place like bathroom.....). Just pay a few extra to buy the LCD+Digitizer for about ~$30 that will save you a lot headache for just the digitizer alone. There's a thread in X1 accessories forum.
I was flashing a rom the other day (that i had flashed in the past and worked fine) and then i noticed that the touchscreen did not work. (everything else worked)
i flashed back to the cyanogen rom and my touchscreen still did not work.
(when i say my touchscreen doesnt work i mean that i cant touch anything, not even the android to set up my phone)
the trackball works but i am FORCED to touch the android and i cant
ive been flashing and still no luck, any ideas on what happened to my touchscreen or any ideas on how to fix it?
please help!!
I've seen a few of the threads. More than likely your touch screen has died (hardware issue - not software) and I'm not sure if that's replaceable.
Ask a technision :/ like the guy above said its proble the tS died may need replacement or ribbon isnt connected rite .
So whats my best bet in going about this?
i dont know what to do :/
if you feel like your able to take apart the phone and replace the screen, you could always try it. either that or buy a new phone or possibly a cell phone repair shop if you even have one.
i decided to kinda drop it.
it works now...
thanks for your help anyways guys!
D:
I wouldn't be DROPPING it to fix it...
Problem is probably a badly seated ribbon cable, which means it is STILL not well seated and will probably happen again.
Look in the screen hinge as you're sliding the screen open -- see the little ribbons in there? Probably got yanked a little.
Hi everyone,
The last few days I've been trying to revive my friends Galaxy S i9000.
He brought it to me when his screen all of a sudden wouldn't work anymore. All that it puts out are faint green, pixelated lines.
At first I thought it to be a crashed ROM or something, so I hooked it up to Odin and started flashing.
Two days later I've been through a whole lot of ROM's, ranging from stock Froyo's to custom ROM's with SpeedKernel I run on my own (still working ) Galaxy S.
All to no avail. The last ROM I flashed is the stock Samsung Gingerbread one, and I can hear the phone booting with the startup sound and all, even hear the keytones when I go over the touchscreen.
But still... the screen is either black, or when I wait a while after booting, looks like the image attached to this post.
I'm starting to think this is a hardware problem. I have already opened up the case but can't see anything wrong, all the connectors and ribbon cables attached to 'em look just fine.
Any suggestions or should I just get a replacement SAMOLED from eBay?
Any help is much appreciated, thanks!
this mofo is dead as hell...
Haha yeah I guess... but it still functions as a phone, with the startup sounds and all, vibrate also works, it's just the screen that's not functioning like it should...
The problem seems to be with the screen, get it checked by any local mobile repairer if it isnt under warranty !
hi guys,
recently my black got broken and i buy a replacement digitizer on ebay
but ever since then the soft keys, dont work, i tried to reassemble it flash different kernel and roms, flash kdz from stock, nothing worked, so i match the old digitizer to the new one and i think they are diferent, maybe a drivers/modules problem? idk its really strange cause the rest of the touchscreen works remarcably well, and the other problem is the proximity sensor it doesnt work, when i test it via 3845*#970# its said fail, and i cant calibrate it, ive tried to make pressure like i saw a youtube video, nothing worked,
Hope someone can help me
thanks
Hello xda community,
I contact you because my mum's phone fall and screen broke.
She took it to a phone repair shop that changed it, but she said it was still not working.
I was away, it was few month ago but now I came back and try the Z1 and touch and screen and everything was working fine when I tried. But after like 10 min no touch.
I found the way to reboot it, and when I reboot most of the time touchscreen work again, but go away fast.
I searched and found some thread talking about software issues for touchscreen, so I tried updating to lineage, but it's doing the same, so I suspect HW failure.
This phone still seems nice to me, the battery seems to still be ok, the screen quality is good, the lineage 16 is fine so... if I can revive it, I'd be happy to do it.
Any idea what can be wrong ? Is there any component failure that could lead to that ?
Thanks guys.