Ok guys, I really didn't want to start this thread but I couldn't find any real kind of answer. So I installed CM7 with moboot on my touchpad, after the installation, the touchpad rebooted and then skipped over the "touch the android" to finish loading cm7. Immediately afterwards I get an error that reads "sd card not mounted might be damaged please click ok to format". Do you any of you guys have any idea what's going on?
I've searched these forums/google and I can't seem to find a solution. So far I'd done a full secure erase from webos, format in recovery, novaterm touchpad type fcsk.vfat.... tried to flash other versions of cm7 after a webos doctor.
I'm still trying other options, but I wanted to pick the brains of the fine people here on this forum and see what you guys think.
Thanks a million!
Spazzvogel said:
Ok guys, I really didn't want to start this thread but I couldn't find any real kind of answer. So I installed CM7 with moboot on my touchpad, after the installation, the touchpad rebooted and then skipped over the "touch the android" to finish loading cm7. Immediately afterwards I get an error that reads "sd card not mounted might be damaged please click ok to format". Do you any of you guys have any idea what's going on?
I've searched these forums/google and I can't seem to find a solution. So far I'd done a full secure erase from webos, format in recovery, novaterm touchpad type fcsk.vfat.... tried to flash other versions of cm7 after a webos doctor.
I'm still trying other options, but I wanted to pick the brains of the fine people here on this forum and see what you guys think.
Thanks a million!
Click to expand...
Click to collapse
I have same exact problem. Bought used tablet last night with cm7. I'm confused about lack of support for cm7 on touchpad. I should have researched more before I bought it.
Hi. I had run into problems with installing android. So i had to recreate the partitions. It was fine up to that point. However when it comes to the webos doctor,it fails. it keeps rebooting after the trenchcoat feeder. (above 12%. No particular point where it reboots.) Cant find out whats wrong. Will be grateful for some help with this.
A week ago I installed TWRP on my Hp Touchpad, via the GooManager App.
After I rebooted into TWRP it showed a error message. I cant remember what it said. First I just let it broken, but then I wanted to update SlickleROM from Version 1 to 1.1. But i couldnt use the Recovery System, because it didnt work.
So I tried to install the Clockworkmod Recovery and the new ROM with ACMEInstaller2 and ACMEInstaller3, but ACMEInstaller3 did nothing, it just showed the HP logo. ACMEInstaller2 showed a Error Message, that /boot is out of space. So i decided to reset my Touchpad.
First I used ACMEUninstaller to uninstall Android. Then i used WebosDoctor to remove all data, but it said it couldn't reset my phone after a few minutes. My Touchpad could'nt boot. It just shutdown everytime it was booting. I stopped the endless rebooting with holding Power Button and Pressing Home Button 10 Times. After that I tried to doctor serval times with older versions and tried to find out what was happening. But then the battery was too low. WebosDoctor could charge it and in the outlet it just charged until it was booting again, so i could charge enough to doctor the device. Now I have a not booting Touchpad with a too low battery to doctor.
I already tried to restore it to factory condition with this guide. But the WebosDoctor didnt work
Does anyone know what I can try to do?
ss0198 said:
A weekhttp://goo.im/devs/jcsullins/cmtouchpad/testing ago I installed TWRP on my Hp Touchpad, via the GooManager App.
After I rebooted into TWRP it showed a error message. I cant remember what it said. First I just let it broken, but then I wanted to update SlickleROM from Version 1 to 1.1. But i couldnt use the Recovery System, because it didnt work.
So I tried to install the Clockworkmod Recovery and the new ROM with ACMEInstaller2 and ACMEInstaller3, but ACMEInstaller3 did nothing, it just showed the HP logo. ACMEInstaller2 showed a Error Message, that /boot is out of space. So i decided to reset my Touchpad.
First I used ACMEUninstaller to uninstall Android. Then i used WebosDoctor to remove all data, but it said it couldn't reset my phone after a few minutes. My Touchpad could'nt boot. It just shutdown everytime it was booting. I stopped the endless rebooting with holding Power Button and Pressing Home Button 10 Times. After that I tried to doctor serval times with older versions and tried to find out what was happening. But then the battery was too low. WebosDoctor could charge it and in the outlet it just charged until it was booting again, so i could charge enough to doctor the device. Now I have a not booting Touchpad with a too low battery to doctor.
I already tried to restore it to factory condition with this guide. But the WebosDoctor didnt work
Does anyone know what I can try to do?
Click to expand...
Click to collapse
Try leaving the tp charging, at least overnight, till it's 100% charged. Then try the guide again. If you're having trouble with novaterm, there's a good work around on page 12.
If you're having trouble with the doctor, either the 8% or the 12%, do a search for either. Don't worry, there's a workaround. Also search the webos nation forum, you'll find answers there also.
Good luck.
Edit : use cwm. Myself and several others here have had problems with TWRP.
Here's the link for cwm : http://goo.im/devs/jcsullins/cmtouchpad/recovery
Use the 12/15 one.
AW: [Q] HP Touchpad no longer booting.
I already that, but it only charges until it tries to boot.
Are you using the cable that came with the TP?
AW: [Q] HP Touchpad no longer booting.
Yes.
AW: [Q] HP Touchpad no longer booting.
The problem is, that it tries to boot, but it can't boot.
Have you tried to power it down whilst still plugged in ?
AW: [Q] HP Touchpad no longer booting.
What do you mean with:
sstar said:
Have you tried to power it down whilst still plugged in ?
Click to expand...
Click to collapse
What I mean is you have your TP charging and it automatically boots when it has sufficient charge, while leaving still connected to the charger have /can you turn it off but leave it connected?
AW: [Q] HP Touchpad no longer booting.
I will try it now.
AW: [Q] HP Touchpad no longer booting.
I just tried it, but it instantly reboots after turning it off.
It's obviously stuck in some sort of loop, my final thought is to hold both power and volume to put it into recovery and leave it so that it hopefully continues to charge .
You said you had a problem with running chicle's suggestion with the restore your TP to factory condition, how far did you get ?
AW: [Q] HP Touchpad no longer booting.
I alreqdy tried to charge it in recovery mode, but the battery didn't charge either. I tried to reset it with serval versions of the webosdoctor, but as I said it didn't work. It just said it couln't reset the phone. In the console/log it crashed at charging. And it list connection.
When you say ' I already tried to restore it to factory condition with this guide. But the WebosDoctor didnt work "
Does that mean you were able to run all the instructions in command prompt and then failed with webos doctor 3.0.0 ?
sstar said:
When you say ' I already tried to restore it to factory condition with this guide. But the WebosDoctor didnt work "
Does that mean you were able to run all the instructions in command prompt and then failed with webos doctor 3.0.0 ?
Click to expand...
Click to collapse
Yes.
ss0198 said:
Yes.
Click to expand...
Click to collapse
Well I'm at a loss ,if or when you can try the factory restore commands followed by webos Doctor 3.0.0 again. I had to do it twice with mine.
That's all i can think of. Good luck.
sstar said:
Well I'm at a loss ,if or when you can try the factory restore commands followed by webos Doctor 3.0.0 again. I had to do it twice with mine.
That's all i can think of. Good luck.
Click to expand...
Click to collapse
I already did it twice
Now I finally got it working. I just charged it in Recovery Mode for a long time. Then I just used Webosdoctor and now it works!
Sent from my ss_tenderloin using xda app-developers app
Hey guys!
I recently resized the partitions of my touchpad via the recommended cwm zips, in order to install latest 4.3.1.
Everything worked as expected.
After experiencing quite high battery drain I decided to reflash the A6 firmware, as I already did several times.
When I try to boot up WebOS, I'm stuck in a bootloop. The HP sign is flashing/blinking but it never boots up!
Seems the resizing deleted an important file or similar.
Is there any safe possibility to workaround this? Android is working normal, when I connect to a PC I can only see the MTP Media device, no other partitions.
Should I use WebOS doctor?
Hope somebody has a helpful idea.
Thank you in advance.
spica123 said:
Hey guys!
I recently resized the partitions of my touchpad via the recommended cwm zips, in order to install latest 4.3.1.
Everything worked as expected.
After experiencing quite high battery drain I decided to reflash the A6 firmware, as I already did several times.
When I try to boot up WebOS, I'm stuck in a bootloop. The HP sign is flashing/blinking but it never boots up!
Seems the resizing deleted an important file or similar.
Is there any safe possibility to workaround this? Android is working normal, when I connect to a PC I can only see the MTP Media device, no other partitions.
Should I use WebOS doctor?
Hope somebody has a helpful idea.
Thank you in advance.
Click to expand...
Click to collapse
EDIT: Okay. at least acmeuninstaller brought webos back to life.
All of a sudden after a year running cm10 (I think) my touchpad gets stuck in the infinite boot loop. The cyanogenmod logo comes up and the arrow goes around in a circle than freezes and goes back to moboot. I just tried to install 10.1 and the same thing happened. Should I just try to use ACMEuninstaller and install everything again? Do I just run the uninstaller through the command prompt? Is there an easier way to do this? My usb connection for the device seems to be spotty too. I can't touch it or it loses connection. Any help would be appreciated. I haven't updated my touchpad in a long time.
Update: I used the uninstaller than followed the guider here http://forum.xda-developers.com/showthread.php?p=37965549#post37965549
I got passed the loop a couple times only to have the touchpad crash as I was setting it up. Now it is back to the reboot loop. Any other ideas? My webOs isn't working properly too. I installed the update for that a long time ago but now I can't connect to the app catalog or even set up my email accounts.
What is the best way to completely wipe CM?
donniebball23 said:
What is the best way to completely wipe CM?
Click to expand...
Click to collapse
Right above your question
shumash said:
Right above your question
Click to expand...
Click to collapse
Yeah, I did that and tried to reinstall cm10.1 and still had the loop problem. Going to uninstall again and try the toolbox. That looks pretty cool.
Now I cannot get anything to even finish installing. The installation process is stuck on "clock dg_timer, alarm already expired, now...." I think my touchpad is toast.
donniebball23 said:
Now I cannot get anything to even finish installing. The installation process is stuck on "clock dg_timer, alarm already expired, now...." I think my touchpad is toast.
Click to expand...
Click to collapse
Are you trying to install CM10.1 with the TPtoolbox? You're not giving enough information about what you're up to or the files you're trying to use. Do a complete data reset then try and install Jcsullins CM11.