My kids received Nook Color readers for Christmas, and like everything, they look to Dad to optimize them.
I was going to try rooting, but a couple of things remain unclear:
- Do I have to 'auto-noot' to root the Noot, or are there other options (other tools, manual rooting, etc.)
- Should I upgrade the software to 1.0.1 prior to rooting or not?
I tried to give auto-noot for 1.0.0 a quick run, but I couldn't get the SD card to boot (and a check revealed that I had two FAT16 partitions, one with the appropriate images and the other with the files needed). I'm assuming it's because the card I have might be too slow (portal recommends Class 6 or greater, and the card I'm using is a cheapo card I got with an earlier phone that I'm not too sure of).
Thoughts? Tips?
I upgraded mine to 1.0.1 first then rooted.
What OS is on your PC?
If Windows, did you use Win32DiskImager to write the image to microSD card?
Take a look at here for different ways of rooting here http://www.nookdevs.com/Portal:NookColor#Rooting
The easiest and the way I rooted is below which I borrowed from http://blogkindle.com/2010/12/read-kindle-books-on-nook-color/
Here’s what you need to do:
1. Before rooting make sure that you’ve registered the device with B&N as it might not work after rooting.
2. Download nooter that corresponds to you Nook version. You can check your Nook version by pressing Nook button, selecting “Settings” >> “Device Info” >> “About your NOOKcolor” >> Software version:
--- for 1.0.0 – GabrialDestruir’s auto nooter 2.12.15 file 15 Dec 2010
--- for 1.0.1 – GabrialDestruir’s auto nooter 2.12.25 file 25 Dec 2010
3. Unpack the file
4. On Windows use Win32DiskImager to write the image to microSD card (please note that all data on the card will be lost). For Linux or Mac, check out NookDevs.com for detailed microSD imaging instructions.
5. Completely power off NOOKcolor by holding the power button until the screen blurs and “Power off NOOKColor” dialog appears. Select “Power Off” and wait for the device to shut down completely.
6. Turn device face down and open the microSD card container in the lower right corner. Push the card in with metal contacts facing down.
7. Connect the device to your computer via USB cable. The device will power up and book from the SD card but the screen will not turn on. This is normal.
8. After about a minute your computer show detect the new device. This means that the rooting is complete. Your Windows computer will complain about missing drivers. This is normal.
9. Disconnect the USB cable and remove the card from the reader.
10. Power cycle it by holding the power button for 20 seconds and then releasing it. The press the power button briefly to power the reader on.
11. As the reader boots you will see a red splash screen.
12. Once the reader boots, you will be prompted for you Gmail account (as usually with Android) and some initial settings. This will only happen once.
13. As you open the extras folder you will see that it now contains Android market icon and some extras (Youtube, Gmail, etc)
14. You can now start the market app and download other apps that you like. You will need to reboot the device for apps to appear on the extras page. The apps themselves can be used right away just as with usual Android apps.
I would look for the thread in the android development section for auto nook 1.01. Update the OS to 1.01, then do the nook-ing process. Its all laid out there in the opening post.
I would definitely root your nooks to get the most out of them.
I'm guessing he meant Auto-Nooter 2.12.25 (1.0.1 Only), which the thread can be found here
I was looking for a manual method because I didn't have my card reader at work yesterday, and I couldn't get the card I wrote in my Incredible to boot Auto-Noot in 1.0.0.
Oddly enough, after deciding to upgrade to 1.0.1 first, when I tried to root the second time it worked just fine. I did the second one after upgrading, also went without a hitch. Think it just makes sense to upgrade first, seeing as they're both exploitable.
giantcrazy said:
I was looking for a manual method because I didn't have my card reader at work yesterday, and I couldn't get the card I wrote in my Incredible to boot Auto-Noot in 1.0.0.
Oddly enough, after deciding to upgrade to 1.0.1 first, when I tried to root the second time it worked just fine. I did the second one after upgrading, also went without a hitch. Think it just makes sense to upgrade first, seeing as they're both exploitable.
Click to expand...
Click to collapse
How can you write an image from your Incredible? You need to use a computer to write the "image" not just the files to the sdcard, to make it bootable.
-CC
clockcycle said:
How can you write an image from your Incredible? You need to use a computer to write the "image" not just the files to the sdcard, to make it bootable.
-CC
Click to expand...
Click to collapse
I spent some time re-inventing the wheel before I realized someone had documented the method on XDA (my fault for being search lazy):
http://forum.xda-developers.com/showthread.php?t=889001
You use the Linux DD command to write the image to the SD card, which renders it with the correct partitions and files needed to complete root. I did it yesterday, and assumed that I had either too slow a card or it didn't work, until I upgraded to 1.0.1 first and it worked at first crack. Just take care to write the card with the correct device name, mmcblk1.
I used GParted on Linux to double-check after doing my fdisk, everything looked kosher to me and it worked flawlessly.
giantcrazy said:
I spent some time re-inventing the wheel before I realized someone had documented the method on XDA (my fault for being search lazy):
http://forum.xda-developers.com/showthread.php?t=889001
You use the Linux DD command to write the image to the SD card, which renders it with the correct partitions and files needed to complete root. I did it yesterday, and assumed that I had either too slow a card or it didn't work, until I upgraded to 1.0.1 first and it worked at first crack. Just take care to write the card with the correct device name, mmcblk1.
I used GParted on Linux to double-check after doing my fdisk, everything looked kosher to me and it worked flawlessly.
Click to expand...
Click to collapse
Ah, totally forgot about that.. Well glad you got it sorted.
-CC
I'm new to the Nook scene, but I've read the someone/leapinlear threads on rooting/putting google apps on the device.
Now that 2.0.5 is out, that seems to break the above.
One of my confusions is the talk of OOBE ( a new acronym for me to learn. )
Is it possible for me to open the Nook HD+ on xmas morning, and play with it without registering/updating?
Does the Nook force you to connect to wifi? What if I had no wifi?
If I can play with it without registering/updating, then use the current rooting methods later in the afternoon ... will that stop 2.0.5?
Do I need to read more?
curiousmike said:
I'm new to the Nook scene, but I've read the someone/leapinlear threads on rooting/putting google apps on the device.
Now that 2.0.5 is out, that seems to break the above.
One of my confusions is the talk of OOBE ( a new acronym for me to learn. )
Is it possible for me to open the Nook HD+ on xmas morning, and play with it without registering/updating?
Does the Nook force you to connect to wifi? What if I had no wifi?
If I can play with it without registering/updating, then use the current rooting methods later in the afternoon ... will that stop 2.0.5?
Do I need to read more?
Click to expand...
Click to collapse
You said you read my thread. Yes you can do the xmas thing by skipping OOBE ( look in my thread for how to do it). Which basically means skipping registration. And you don't have to turn on wifi so that it updates itself. But you do have to turn on wifi to register and you can do nothing with it without either registering or skipping OOBE. But it may be kind of not much fun without apps, books and wifi. I also just posted a new way to have an old version and still register. But you might want to wait to see if other users do ok with it.
Sent from my HD+ rooted stock using Tapatalk
leapinlar said:
Yes you can do the xmas thing by skipping OOBE ( look in my thread for how to do it).
Click to expand...
Click to collapse
Found it and read it. Great.
leapinlar said:
But it may be kind of not much fun without apps, books and wifi
Click to expand...
Click to collapse
Agreed.
But I also don't want to do the update and risk never being able to root it and get Google App Store on it; I have a large array of apps/games for my phone that I'm hoping will work on the HD+.
You can immediately boot straight to CM10 without registering if you'd like. That's exactly what I did, and it has worked flawlessly.
OOBE, known as Out-of-Box-Experience. Basically after registering, you get the experience you should. Skipping OOBE is basically not registering the product, and entering a development/test mode. OOBE is associated with not registering the device.
The Nook HD+ requires a WiFi connection to register the product, and what if the end-user doesn't have WiFi? I guess that's tough on them, they can't register. To be honest, I can't believe it either. To use the HD+ if you do not have WiFi, is to skip OOBE (which is the same procedure as the Nook Color's).
If you skip OOBE, then there is nothing to play with on the tablet; other than familiarising yourself with the interface. That's it. Not even the browser works; actually it has no apps at all. If you later root the tablet [and install GAPPs], whilst not registering the tablet, you will eventually get a lot more features; and pretty much use it like any other Android tablet. However, a lot of features will be disabled, such as the stock Android Browser (it will not load, as it will not be installed). A lot of other apps may then cause problems, due to the default browser not being present (i.e. BBC iPlayer). With the All in One root, developed by someone0, it will disable automatic OTA updates, so you will not update any further than your current factory version. However, some users (including myself) have been forced the update, so you cannot be certain that you will remain on the factory version (those prior to 2.0.5).
However, I would recommend you reconsider your options. If you want a better experience, I would recommend that you register the device (do NOT register now, please read the rest of my post). Important, remember the credentials you register the device with. If there are any future updates for the Nook, you will need to input the same e-mail address and password (unless password changed). If you create another B&N account at this stage, your Nook will constantly output an error; I contacted B&N today, and they couldn't solve it either. I found the solution, you have to remember the exact e-mail address you used to register. So, remember the e-mail address you use to register; and absolutely the password too, or the security question. Without them, you will not be able to register your device again.
Continuing on, I stated I would recommend you to register the device. However, before you do so, please make sure you have a minimum 4GB microSD card present (I used a SanDisk 4GB class 4). When you register your device, your Nook will check for updates. It will find 2.0.5 and update to it. Just so you know, someone0 and leapinlar have worked together to bring a "Universal Root" for the Nook HD+ and that universal root even roots version 2.0.5 (thank you someone0 and leapinlar; I'm currently using it). After registering your device, you will be introduced to your Nook interface. It's empty, even the apps are pretty much useless (except for Browser, only positive); you can't even spend more than 10 minutes on it, without enjoying what your doing. So I would recommend the root + GAPPs to unlock most of the "Android" features. To use the universal root, you'll need to boot into CWM (ClockWorkMod) via SD card (minimum of 4GB, anything less won't be detected/viable). Before registering and continuing with what I say, please make sure you are able to write onto your SD card using your computer. Although we are using CWM, we are NOT going to flash any ROMs (unless you want to of course, but the following "guide" below won't detail so).
First, you'll need to insert your SD card into your computer; where you're in a position where you can write on the card. (Files links/sources/information was sourced from http://forum.xda-developers.com/showthread.php?t=2062613)
Write the CWM .img (NookHD+bootable-CWM-6023-for-emmc-stock-4GB.zip) onto the SD Card using "Win32diskimager in Windows or use the dd command in Linux or OSX".
Download NookHD+Universal-Root.zip and place it within the SD Card. Also do this for the GAPPS + EXTRAS (including ManualOTA and Unknown Sources) .zip file, which you can download here (put together by leapinlar). DO NOT extract the .zip, just place them into the SD card.
At this point, make sure you have registered your Nook HD+, updated and installed version 2.0.5. Also make sure you have launched the stock ROM at least once (i.e. turned on the device into the Nook software/modified Android OS).
Now, turn off your device (hold the power button until a message is displayed on screen, and press shut down, or similar on screen). At the bottom of the Nook, on the left of the charging port, there is a cover protecting the SD card slot. Take it out (not all the way, it's attached to the body), and place in your SD card (with the CWM and universal root, as well optionally the GAPPS; although recommend installed on the SD card).
With the SD card in, turn your Nook on. After a few seconds, you should load into CWM. Select the option "install .zip from SD card" (use volume up/down to move across the list, "n" button below screen to select, and power button to move up one menu).
Firstly, install "NookHD+Universal-Root.zip". Wait for it to fully install, then install the GAPPS + Extras.
After the last step, reboot your device and take out the SD card before reboot. You should now load into your stock OS, whilst being rooted and and GAPPs installed on version 2.0.5. Success!
After the above guide, I would personally recommend Nova Launcher Prime; it unleashes the full experience of Android for me anyway. Haha, from now it's all yours.
That should be all from me, and the best of luck. I support you either way, whether you register or not. Merry Christmas too by the way.
HiddenG said:
OOBE, known as Out-of-Box-Experience.
That should be all from me, and the best of luck. I support you either way, whether you register or not. Merry Christmas too by the way.
Click to expand...
Click to collapse
Fantastic; I happen to have a 4GB card and I'm writing out the .img as I type.
Merry Christmas to you.
Yea, I probably taking a day off from xda forum tomorrow, so enjoy guys.
leapinlar deserves most of the credits since he is doing all the scripting and testing. All I did was giving him ideas(good and bad).
Ahh.. CuriousMike, from BARF, right?
Small world. Let me reemphasize that if you immediately throw in the CM10 install, you can totally skip the registration step. You essentially boot around it, and the next time the device boots without the CM10 SD card plugged in, if you so choose, it will be like opening it up fresh out of the box, with the nook asking you to register and so on.
If you *just* want a full android tablet, the CM10 SD is by far the way to go. Odds are your Xmas wrapped nook doesn't yet have 2.0.5 installed. You should be able to jump straight into CM10 and avoid the current mess of trying to preserve root, avoiding updates, working around the B & N interface and so on. It doesn't mean you can't do that at a later date, but right now CM10 seems to be a much better option than trying to deal with the B&N interface. Best part is that you can continually boot right off that SD card and never have to worry about dodging updates.
I'd recommend it above the current alternative of trying to root and apply fixes to have a usable tablet.
KestrelYI said:
Ahh.. CuriousMike, from BARF, right?
Small world. Let me reemphasize that if you immediately throw in the CM10 install, you can totally skip the registration step. You essentially boot around it, and the next time the device boots without the CM10 SD card plugged in, if you so choose, it will be like opening it up fresh out of the box, with the nook asking you to register and so on.
If you *just* want a full android tablet, the CM10 SD is by far the way to go. Odds are your Xmas wrapped nook doesn't yet have 2.0.5 installed. You should be able to jump straight into CM10 and avoid the current mess of trying to preserve root, avoiding updates, working around the B & N interface and so on. It doesn't mean you can't do that at a later date, but right now CM10 seems to be a much better option than trying to deal with the B&N interface. Best part is that you can continually boot right off that SD card and never have to worry about dodging updates.
I'd recommend it above the current alternative of trying to root and apply fixes to have a usable tablet.
Click to expand...
Click to collapse
I guess we can disagree on that. The way I see it, doing Skip OOBE and then root it would be more stable than CM10. A lot of things still not working yet on CM10. So, I decided to stick w/ stock for my personal use. Considering there is universal root for 2.0.5 now also, it's possible to be on 2.0.5 and still get root+gapps. I guess it could just end up being what do you need it for.
my nook is up
posting this from the nook, using firefox! surprising that chrome comes up as not-compatible.
i've got a few of my play store apps already installed... looking good.
i bought nova-launcher for 0.25$ during googles last big sale, so i'm using that. the experience is androidy-enough.
word-hero is also incompatible... that will push me to "cm10" when it's compatibler-er.
My Nook HD+ came out of the box with 2.0.2 and hasn't updated to 2.0.5 after a couple hours of use. Tried a couple times to do a manual update and says no updates available. ??
Will this work, on my registered device? I have it all setup and working on205, but want gapps too.
Thanks,
Steve
piperman7 said:
Will this work, on my registered device? I have it all setup and working on205, but want gapps too.
Thanks,
Steve
Click to expand...
Click to collapse
It worked for me, just as described.
That sounds good, I just picked up a 8gb class 10 to use.
Thanks again,
Steve
HiddenG said:
OOBE, known as Out-of-Box-Experience. Basically after registering, you get the experience you should. Skipping OOBE is basically not registering the product, and entering a development/test mode. OOBE is associated with not registering the device.
The Nook HD+ requires a WiFi connection to register the product, and what if the end-user doesn't have WiFi? I guess that's tough on them, they can't register. To be honest, I can't believe it either. To use the HD+ if you do not have WiFi, is to skip OOBE (which is the same procedure as the Nook Color's).
If you skip OOBE, then there is nothing to play with on the tablet; other than familiarising yourself with the interface. That's it. Not even the browser works; actually it has no apps at all. If you later root the tablet [and install GAPPs], whilst not registering the tablet, you will eventually get a lot more features; and pretty much use it like any other Android tablet. However, a lot of features will be disabled, such as the stock Android Browser (it will not load, as it will not be installed). A lot of other apps may then cause problems, due to the default browser not being present (i.e. BBC iPlayer). With the All in One root, developed by someone0, it will disable automatic OTA updates, so you will not update any further than your current factory version. However, some users (including myself) have been forced the update, so you cannot be certain that you will remain on the factory version (those prior to 2.0.5).
However, I would recommend you reconsider your options. If you want a better experience, I would recommend that you register the device (do NOT register now, please read the rest of my post). Important, remember the credentials you register the device with. If there are any future updates for the Nook, you will need to input the same e-mail address and password (unless password changed). If you create another B&N account at this stage, your Nook will constantly output an error; I contacted B&N today, and they couldn't solve it either. I found the solution, you have to remember the exact e-mail address you used to register. So, remember the e-mail address you use to register; and absolutely the password too, or the security question. Without them, you will not be able to register your device again.
Continuing on, I stated I would recommend you to register the device. However, before you do so, please make sure you have a minimum 4GB microSD card present (I used a SanDisk 4GB class 4). When you register your device, your Nook will check for updates. It will find 2.0.5 and update to it. Just so you know, someone0 and leapinlar have worked together to bring a "Universal Root" for the Nook HD+ and that universal root even roots version 2.0.5 (thank you someone0 and leapinlar; I'm currently using it). After registering your device, you will be introduced to your Nook interface. It's empty, even the apps are pretty much useless (except for Browser, only positive); you can't even spend more than 10 minutes on it, without enjoying what your doing. So I would recommend the root + GAPPs to unlock most of the "Android" features. To use the universal root, you'll need to boot into CWM (ClockWorkMod) via SD card (minimum of 4GB, anything less won't be detected/viable). Before registering and continuing with what I say, please make sure you are able to write onto your SD card using your computer. Although we are using CWM, we are NOT going to flash any ROMs (unless you want to of course, but the following "guide" below won't detail so).
First, you'll need to insert your SD card into your computer; where you're in a position where you can write on the card. (Files links/sources/information was sourced from http://forum.xda-developers.com/showthread.php?t=2062613)
Write the CWM .img (NookHD+bootable-CWM-6023-for-emmc-stock-4GB.zip) onto the SD Card using "Win32diskimager in Windows or use the dd command in Linux or OSX".
Download NookHD+Universal-Root.zip and place it within the SD Card. Also do this for the GAPPS + EXTRAS (including ManualOTA and Unknown Sources) .zip file, which you can download here (put together by leapinlar). DO NOT extract the .zip, just place them into the SD card.
At this point, make sure you have registered your Nook HD+, updated and installed version 2.0.5. Also make sure you have launched the stock ROM at least once (i.e. turned on the device into the Nook software/modified Android OS).
Now, turn off your device (hold the power button until a message is displayed on screen, and press shut down, or similar on screen). At the bottom of the Nook, on the left of the charging port, there is a cover protecting the SD card slot. Take it out (not all the way, it's attached to the body), and place in your SD card (with the CWM and universal root, as well optionally the GAPPS; although recommend installed on the SD card).
With the SD card in, turn your Nook on. After a few seconds, you should load into CWM. Select the option "install .zip from SD card" (use volume up/down to move across the list, "n" button below screen to select, and power button to move up one menu).
Firstly, install "NookHD+Universal-Root.zip". Wait for it to fully install, then install the GAPPS + Extras.
After the last step, reboot your device and take out the SD card before reboot. You should now load into your stock OS, whilst being rooted and and GAPPs installed on version 2.0.5. Success!
After the above guide, I would personally recommend Nova Launcher Prime; it unleashes the full experience of Android for me anyway. Haha, from now it's all yours.
That should be all from me, and the best of luck. I support you either way, whether you register or not. Merry Christmas too by the way.
Click to expand...
Click to collapse
Just got my Nook HD+ for Christmas, 1st Android device. I followed the above instructions to root it, after reboot it is just sitting at the first nook screen. It's been about 15 minutes or so, should I manually reboot the device or wait longer? Is it possible it just needs to be redone? The only odd thing I can across was after selecting reboot it said "ROM may flash stock recovery on reboot", should i have selected Yes/No, Should I backup the stock ROM?
Thanks for all the Help
curiousmike said:
posting this from the nook, using firefox! surprising that chrome comes up as not-compatible.
i've got a few of my play store apps already installed... looking good.
i bought nova-launcher for 0.25$ during googles last big sale, so i'm using that. the experience is androidy-enough.
word-hero is also incompatible... that will push me to "cm10" when it's compatibler-er.
Click to expand...
Click to collapse
Glad you got your tablet working with GAPPs! Hope it's all good; of course it's much better than sticking to B&N's book reader, haha. Indeed yes, I can't believe that a few apps in Google Play are not compatible either; although as suggested, sideloading them often work fine. :laugh:
mzjc said:
My Nook HD+ came out of the box with 2.0.2 and hasn't updated to 2.0.5 after a couple hours of use. Tried a couple times to do a manual update and says no updates available. ??
Click to expand...
Click to collapse
Did you skip the OOBE? The registration process of the device? If so, this problem could occur. If not, and you're registered then no problem either. If you're truly stuck on 2.0.2, that could be seen as a benefit; as your roots would never be broken, due to no future updates. If you'd like to root and place GAPPs on your tablet, I'd recommend you follow someone0's all-in-one guide. someone0's allinone will root your Nook HD+, install GAPPs, manual OTA and installation from Unknown Sources; provided your HD+ is on version 2.0.0 to 2.0.4, where you are eligible. This rooting method provides the exact same end-result as the 2.0.5 root, and is no different in performance or usability; they're exactly the same, just different installation process.
I've not tested it, but you may use the same rooting process as I've described on the last page; since the rooting method is universal. However, I have not tested it, other than on version 2.0.5. You'll also need a microSD card for this process, so I'd just recommend the adb-allinone method by someone0.
Best of luck.
ifdwolf2008 said:
Just got my Nook HD+ for Christmas, 1st Android device. I followed the above instructions to root it, after reboot it is just sitting at the first nook screen. It's been about 15 minutes or so, should I manually reboot the device or wait longer? Is it possible it just needs to be redone? The only odd thing I can across was after selecting reboot it said "ROM may flash stock recovery on reboot", should i have selected Yes/No, Should I backup the stock ROM?
Thanks for all the Help
Click to expand...
Click to collapse
First Android device? Haha, hopefully it'll make a good impression after rooting and GAPPS. Sorry about the wait. Once you've loaded/rebooted into the Nook HD+ after CWM/rooting/GAPPS etc, press the "n" button below the screen. You should be given the option to select a launcher; temporarily select ZeamLauncher and set it as default action. After that, you should be good to go. Personally, I would recommend Nova Launcher Prime instead of ZeamLauncher. If you'd like, you can download the free version of Nova Launcher from Google Play (I would recommend it strongly over ZeamLauncher). It should provide you a better "Android-experience".
If pressing the 'n' button below the screen did nothing, then you can try the rooting process again. Also selecting yes, or no shouldn't make a difference during reboot; "ROM may flash stock recovery on reboot". You may backup your stock ROM if you feel necessary, but it's not absolutely essential (if you ever run into problems, you can force the tablet to fail booting 8 times, and the tablet will automatically restore to factory defaults). If you have further problems, please reply.
Best of luck.
Boom, thanks for the help, working like a champ now! Does the mic feature in nova require chrome? Gonna side load it now. Device is much better rooted, big thanks all to all envolved!
Sent from my BNTV600 using xda app-developers app
Hey folks. I'm having some issues with the "Root your device with a bootable microSD card" method. I followed the instructions precisely.. wrote the image to a 32 GB microSD (I don't own any 4 GB cards).. and my nook REFUSES to even see the card nor boot from it for that matter.. just goes straight to the registration screen every time. Is there something that I could perhaps be missing here...? or is it that I MUST have a 4 GB card (and no bigger)?? (the microSD is the cream of the crop Sandisk 32 GB class 10 model. I couldn't resist picking one up, as they were on sale for only $26 at the time.
My HD+ is a pretty paperweight at the moment, and I'd love to get it back up and running. I really don't want to do the "all in one" method, as it keeps you in "TEST" mode.. which bugs the crap outta me.
What am I missing?!
HiddenG said:
OOBE, known as Out-of-Box-Experience. Basically after registering, you get the experience you should. Skipping OOBE is basically not registering the product, and entering a development/test mode. OOBE is associated with not registering the device.
The Nook HD+ requires a WiFi connection to register the product, and what if the end-user doesn't have WiFi? I guess that's tough on them, they can't register. To be honest, I can't believe it either. To use the HD+ if you do not have WiFi, is to skip OOBE (which is the same procedure as the Nook Color's).
If you skip OOBE, then there is nothing to play with on the tablet; other than familiarising yourself with the interface. That's it. Not even the browser works; actually it has no apps at all. If you later root the tablet [and install GAPPs], whilst not registering the tablet, you will eventually get a lot more features; and pretty much use it like any other Android tablet. However, a lot of features will be disabled, such as the stock Android Browser (it will not load, as it will not be installed). A lot of other apps may then cause problems, due to the default browser not being present (i.e. BBC iPlayer). With the All in One root, developed by someone0, it will disable automatic OTA updates, so you will not update any further than your current factory version. However, some users (including myself) have been forced the update, so you cannot be certain that you will remain on the factory version (those prior to 2.0.5).
However, I would recommend you reconsider your options. If you want a better experience, I would recommend that you register the device (do NOT register now, please read the rest of my post). Important, remember the credentials you register the device with. If there are any future updates for the Nook, you will need to input the same e-mail address and password (unless password changed). If you create another B&N account at this stage, your Nook will constantly output an error; I contacted B&N today, and they couldn't solve it either. I found the solution, you have to remember the exact e-mail address you used to register. So, remember the e-mail address you use to register; and absolutely the password too, or the security question. Without them, you will not be able to register your device again.
Continuing on, I stated I would recommend you to register the device. However, before you do so, please make sure you have a minimum 4GB microSD card present (I used a SanDisk 4GB class 4). When you register your device, your Nook will check for updates. It will find 2.0.5 and update to it. Just so you know, someone0 and leapinlar have worked together to bring a "Universal Root" for the Nook HD+ and that universal root even roots version 2.0.5 (thank you someone0 and leapinlar; I'm currently using it). After registering your device, you will be introduced to your Nook interface. It's empty, even the apps are pretty much useless (except for Browser, only positive); you can't even spend more than 10 minutes on it, without enjoying what your doing. So I would recommend the root + GAPPs to unlock most of the "Android" features. To use the universal root, you'll need to boot into CWM (ClockWorkMod) via SD card (minimum of 4GB, anything less won't be detected/viable). Before registering and continuing with what I say, please make sure you are able to write onto your SD card using your computer. Although we are using CWM, we are NOT going to flash any ROMs (unless you want to of course, but the following "guide" below won't detail so).
First, you'll need to insert your SD card into your computer; where you're in a position where you can write on the card. (Files links/sources/information was sourced from http://forum.xda-developers.com/showthread.php?t=2062613)
Write the CWM .img (NookHD+bootable-CWM-6023-for-emmc-stock-4GB.zip) onto the SD Card using "Win32diskimager in Windows or use the dd command in Linux or OSX".
Download NookHD+Universal-Root.zip and place it within the SD Card. Also do this for the GAPPS + EXTRAS (including ManualOTA and Unknown Sources) .zip file, which you can download here (put together by leapinlar). DO NOT extract the .zip, just place them into the SD card.
At this point, make sure you have registered your Nook HD+, updated and installed version 2.0.5. Also make sure you have launched the stock ROM at least once (i.e. turned on the device into the Nook software/modified Android OS).
Now, turn off your device (hold the power button until a message is displayed on screen, and press shut down, or similar on screen). At the bottom of the Nook, on the left of the charging port, there is a cover protecting the SD card slot. Take it out (not all the way, it's attached to the body), and place in your SD card (with the CWM and universal root, as well optionally the GAPPS; although recommend installed on the SD card).
With the SD card in, turn your Nook on. After a few seconds, you should load into CWM. Select the option "install .zip from SD card" (use volume up/down to move across the list, "n" button below screen to select, and power button to move up one menu).
Firstly, install "NookHD+Universal-Root.zip". Wait for it to fully install, then install the GAPPS + Extras.
After the last step, reboot your device and take out the SD card before reboot. You should now load into your stock OS, whilst being rooted and and GAPPs installed on version 2.0.5. Success!
After the above guide, I would personally recommend Nova Launcher Prime; it unleashes the full experience of Android for me anyway. Haha, from now it's all yours.
That should be all from me, and the best of luck. I support you either way, whether you register or not. Merry Christmas too by the way.
Click to expand...
Click to collapse
Hey there. I followed your directions EXACTLY as posted. I didn't have a 4 GB microSD, but I DID have a 32 GB class 4. I used that. Long story short, the nook will NOT "see" nor boot from said microSD no matter what I do. Is there some sort of button combo I need to be doing while the nook HD+ is turning on to see the sd card? I'm totally lost on this.
Thanks in advance for your help!!
If you'd like to PM me, that way my email will notify me when a response has been received, I'd REALLY appreciate it! Thanks for all your hard work!
The one difference might be that I did the whole oobe; I registered the nook... I rebooted twice to the stock Os (somewhere I read that you had to reboot once after setting up bn account.) I don't know if that's your issue, but it's what I did and I'm running gapps.
Sent from my SPH-L710 using Tapatalk 2
If this is in the wrong place (it seemed like a general Q & A) I apologize, but need your help - if it is possible could someone send me the driver file for the Nook HD+, or tell me an easier way to get it than registering as a B&N developer?
Here's why - I don't really wish to register as a developer; I simply don't have time to get in to that. I'm sure they're not expecting me to churn out an app every 6 months to a year, but I just don't wish to sign up.
All I want is a way to get these drivers on my PC so that I can get Helium from the Google pay store installed on this device. I have several app data files stored on Google Drive and want to be able to play things from where I left off without having to root the device.
I understand it's difficult to get them on the PC via windows and I'm pretty green here still....if you know of a better way to get the current drivers on my PC I would appreciate it if you'd tell me. I did read / skim all 33 pages of Q & A looking for anything that might point me in the right direction but if I saw it I didn't know I was looking at it. Sorry - and thanks ahead of time for any help!
Prof24 said:
If this is in the wrong place (it seemed like a general Q & A) I apologize, but need your help - if it is possible could someone send me the driver file for the Nook HD+, or tell me an easier way to get it than registering as a B&N developer?
Here's why - I don't really wish to register as a developer; I simply don't have time to get in to that. I'm sure they're not expecting me to churn out an app every 6 months to a year, but I just don't wish to sign up.
All I want is a way to get these drivers on my PC so that I can get Helium from the Google pay store installed on this device. I have several app data files stored on Google Drive and want to be able to play things from where I left off without having to root the device.
I understand it's difficult to get them on the PC via windows and I'm pretty green here still....if you know of a better way to get the current drivers on my PC I would appreciate it if you'd tell me. I did read / skim all 33 pages of Q & A looking for anything that might point me in the right direction but if I saw it I didn't know I was looking at it. Sorry - and thanks ahead of time for any help!
Click to expand...
Click to collapse
you can find the usb drivers here http://forum.xda-developers.com/showthread.php?p=34168454#post34168454
Thank you Darth for pointing me to the right thread - knew if it was anywhere for download it had to be here somewhere!
All right...running Windows 8 and last night installed the USB drivers. I am using Helium (formerly Carbon) from Clockworkmod.com. When the drivers installed, I now am able to access my internal storage of my Nook HD+ via my PC....but when I run the Helium Desktop version, it cannot find my Nook apparently as it just sits there doing nothing.
Is anyone here familiar enough with this app / combination to know what I'm doing wrong? Reason I ask is I know I saw something aboout adding a line of code yesterday, or similar but I didn't bookmark page and now I can't find the page. Like I said, wish to recover app data without root if possible. The Nook HD+ is on version 2.1.0 (updated upon set up completion).
EDIT: Upon further review I read how to adjust the PC ADB file so it and the Nook could communicate (echo x20800 or something like that) in the documentation pages on developing for the device; this turns on ADB between Nook & PC. I also enabled ADB on the Nook.but so far still no luck with this app.
Update: Have been talking with Helium developers. We are thinking the issue may be the Nook's feature of having external sources turned off.
I decided yesterday, upon further reading, to try and use the SD card version of recovery to back up my system if nothing else (for some reason, when I first read it I thought recovery was permanently installed...not sure why). I feel blessed...when I inserted the card and powered Nook HD+ back on, it went straight to cyanoboot screen! From there backup was made successfully.
My next step was to install leapinlar's "Extra's" zip file. Again, smooth as silk, not a single issue. Without rooting, i figure since extras turns on the "unknown sources" feature, I now have a way to try helium again once the web page is back up.
That aside. I REALLY like the Zeam feature in extras rev 3.zip...and now seeing how simple it is to achieve root, may try it if my current plans to get Helium to run fail.
Only option apparently is to root device. CM 1.0 installed, gapps 4.2.2, helium works and many happy monsters from Monsterama Park roam my screen!
I was able to get Helium to run on my stock Nook HD+.
Got the USB driver from http://forum.xda-developers.com/showthread.php?p=34168454
Followed the "Setting up ADB" section (and part of https://nookdeveloper.zendesk.com/entries/21943338-nook-developer-startup-guide#_Get_Win2See_NOOK )
Then installed and ran Helium Desktop on my Win7: http://www.clockworkmod.com/carbon
While Nook's Developer options' "Enable ADB" is still selected, connected Nook to computer. Helium is then automatically enabled, as indicated by Helium Desktop.
Then I was able to run Helium on Nook just fine.
So is the previous thread still the only way to get Helium working on stock HD+? At what point do I start on the linked site?
Sent from my XT1049 using xda app-developers app
Hello,
I've already sent my device back to Asus, where they did absolutely nothing and just sent it right back to me. Complete waste of $16 shipping.
anyway, a while back I received a notification to update firmware. It downloaded, but then the install failed. About 2 weeks later, it prompted me again, and once again it downloaded but then failed to install on the restart. I decided to download the latest firmware on the Asus website, but I have no option to install by SD Card once I'm in Droidboot. My only options are:
1. REBOOT
2. REBOOT DROIDBOOT
3. RECOVERY
4. POWER OFF
Can someone please help? Asus has been absolutely no help, as I just spent another hour yesterday "chatting" with the rep who knew absolutely nothing!
Thanks in advance, cheers!
Well, I guess I stumped everyone in here as well. I just sent the device back to Asus for the second time in 2 weeks. Let's see if they do anything more than just power on the device, deem it "working properly" and promptly send it back to me.
Shaundiesel said:
Hello,
I've already sent my device back to Asus, where they did absolutely nothing and just sent it right back to me. Complete waste of $16 shipping.
anyway, a while back I received a notification to update firmware. It downloaded, but then the install failed. About 2 weeks later, it prompted me again, and once again it downloaded but then failed to install on the restart. I decided to download the latest firmware on the Asus website, but I have no option to install by SD Card once I'm in Droidboot. My only options are:
1. REBOOT
2. REBOOT DROIDBOOT
3. RECOVERY
4. POWER OFF
Can someone please help? Asus has been absolutely no help, as I just spent another hour yesterday "chatting" with the rep who knew absolutely nothing!
Thanks in advance, cheers!
Click to expand...
Click to collapse
I have (2) K01A MemoPad 170CX's, less than 30-days old. Both updated to 4.4.2 via OTA method running software Image Version: V11.2.3.27. (2014-12-23)
On one all of the sudden (and it may be a case the camera never worked) is when the camera is activated the cam app comes up for (3) seconds with the still icon lit up, then the video icon lights up as well for a (1) second then app exits to desktop with a "No Camera is found" error message.
I've been all over the net trying to find into on how to manually flash it.
According to the very cryptic info on ASUS website step # states:
"2. Download device software and Update SOP (From “Manual” Item)"
Googling for info on SOP, you download firmware in zip format, then do (1) extraction of the contents to a MicroSD card formated FAT32 to the root of the card. (After extraction there is a zip file named ifwi.zip that contains (4) *.bin files that remain inside the zip, you don't extract that zip.)
According to info on SOP, with device powered fully up inserting the sd card is supposed to bring up a prompt, a icon on the taskbar/, you click the prompt and the update process begins.
I'm not seeing that.
All I see when the SD card is inserted is a notification the SD is being prepared for use.
When trying to update via DROIDBOOT (W Fastboot wording at bottom of screen), with SD card inserted the DROIDBOOT menu isn't coming up, when I fire up DROIDBOOT without the SD card inserted and insert it DROIDBOOT does not recognize any change has occurred.
Wanted to try re-flashing WW_V11.2.3.27 as I've read in cases the camera gets the No camera found error message the camera firmware gets corrupted somehow. when you hit the return to home-screen icon too fast, I guess when app is in process of opening and it's closed before it initializes fully.
If that doesn't work, trying Version WW_V11.2.3.28 as I for sure don't want to have to send the device back to ASUS when a simple reflash of the firmware would get the camera working again.
Q: Are / were you getting the same results?
(I guess you didn't try SOP method?)
Q: I guess "Fastboot" means "neutered"? Is there a way to bypass? /enable all functions ASUS would not be able to detect if I have to send in unit for service?
Tried copying the contents of the removable SD card to the internal SD card folder...
Nada, zip, nothing.
ASUS needs to provide info on how to run the flash, I've never had this much trouble flashing a device.
WeAreNotAlone said:
I have (2) K01A MemoPad 170CX's, less than 30-days old. Both updated to 4.4.2 via OTA method running software Image Version: V11.2.3.27. (2014-12-23)
On one all of the sudden (and it may be a case the camera never worked) is when the camera is activated the cam app comes up for (3) seconds with the still icon lit up, then the video icon lights up as well for a (1) second then app exits to desktop with a "No Camera is found" error message.
I've been all over the net trying to find into on how to manually flash it.
According to the very cryptic info on ASUS website step # states:
"2. Download device software and Update SOP (From “Manual” Item)"
Googling for info on SOP, you download firmware in zip format, then do (1) extraction of the contents to a MicroSD card formated FAT32 to the root of the card. (After extraction there is a zip file named ifwi.zip that contains (4) *.bin files that remain inside the zip, you don't extract that zip.)
According to info on SOP, with device powered fully up inserting the sd card is supposed to bring up a prompt, a icon on the taskbar/, you click the prompt and the update process begins.
I'm not seeing that.
All I see when the SD card is inserted is a notification the SD is being prepared for use.
When trying to update via DROIDBOOT (W Fastboot wording at bottom of screen), with SD card inserted the DROIDBOOT menu isn't coming up, when I fire up DROIDBOOT without the SD card inserted and insert it DROIDBOOT does not recognize any change has occurred.
Wanted to try re-flashing WW_V11.2.3.27 as I've read in cases the camera gets the No camera found error message the camera firmware gets corrupted somehow. when you hit the return to home-screen icon too fast, I guess when app is in process of opening and it's closed before it initializes fully.
If that doesn't work, trying Version WW_V11.2.3.28 as I for sure don't want to have to send the device back to ASUS when a simple reflash of the firmware would get the camera working again.
Q: Are / were you getting the same results?
(I guess you didn't try SOP method?)
Q: I guess "Fastboot" means "neutered"? Is there a way to bypass? /enable all functions ASUS would not be able to detect if I have to send in unit for service?
Tried copying the contents of the removable SD card to the internal SD card folder...
Nada, zip, nothing.
ASUS needs to provide info on how to run the flash, I've never had this much trouble flashing a device.
Click to expand...
Click to collapse
I tried everything under the sun....I extracted the zip, nothing. I left it as a zip, nothing. I went to recovery, nothing. You name it, I did it. So, I sent back to Asus for the second time in 2 weeks. I just checked the status of my RMA with Asus, and it states that "No trouble found." I'm not sure how NO TROUBLE IS FOUND when I can't even update to Asus latest firmware for their device? In addition, I do not get the options to try to manually update (Not that I should even have to go that route when it should be OTA). I will never own another Asus product. I've only had my tablet for 4 months, 2 1/2 months of which it sat in my desk, unused. Asus is garbage.
Did you remove any system files or freeze them? Did you root?
lvnatic said:
Did you remove any system files or freeze them? Did you root?
Click to expand...
Click to collapse
No I did not remove any system files or freeze them, that I know of. I rooted shortly after purchasing this, but unrooted the device about 2 weeks later.
Thoughts?
lvnatic said:
Did you remove any system files or freeze them? Did you root?
Click to expand...
Click to collapse
If you are talking to me in which camera(s) both seem to not be found by the OS ME170 is STOCK, STOCK, STOCK.
Contacted the vendor TigerDirect, noticed that they claim they will NOT do exchanges due to "manufacturers polices". While I realize it costs vendor (TigerDirect) to handle exchanges that wording could also indicate they have run the numbers and don't want to be bothered.
Reading about ASUS service, and my interaction with ASUS when I contacted them does not insipre incidence so I'm hoping to be able to flash the device and cameras will start functioning again.
In regards to the customer being able to flash a device (Which I done numerous times on other brands)
I know ASUS is a Asian based manufacturer and sells worldwide but they really need to have persons who can write in better ENGLISH.. ASUS needs to publish detailed instructions on how to flash device, additionally they need to update support pages with any drivers, tools to do so vs just posting the firmware with vaque reference to SOP.
Q: How long after firmware updates appears on ASUS site does OTA update get pushed?
..
Just an update....
Just received my memo pad back, and it appears to be finally fixed. It took sending it back twice, and escalating to a supervisor, but it looks good now. I've actually received 3 firmware updates in 2 days, so it was REALLY behind! What firmware are you all running right now? I have WW-3.2.23.201.
I think 201 is the latest. Mine is still on 199 though and it won't try to update again since it failed a couple of weeks ago.