Related
Anyone have a guide to do a screen replacement on TD?
I dropped mine on the floor and it got a little scrats on the lover right corner.
I can only operate the left side of the phone with a pen and the right side do not work.
Can you also give a link where to buy?
Arrhh
Sorry Dude - Bad luck
No insurance ?
I thought they made the body and screen extra strong with a extra glass plate in between so the screen and body of the TD could fall a few times before it breaks?
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
Hi all
Recently and sadly I dropped my tab and it hit the floor face down right on a corner. Lots of lovely cracks now cover that corner and some go right across the screen. My indecisiveness around picking a case no doubt did not help this situation. It has a screen protecter that holds the broken section in but little chips still come loose. Story being I need to replace it.
There's parts available on ebay and a vid on how to take apart on youtube. My question is has any had any experience? Got any tips?
Apologies if there's a section on this somewhere but I did a search and couldnt find anything.
Thanks
Www.tv-mall.com. They sell the front glass. Google galaxy tab front glass replacement and you will see a youtube video showing you how to dismantle the tab. The link in the video will take you to the store to buy the tools. The project takes a week for the parts to come from China, and twenty minutes to complete. The cost was $130 US.
hii people i need some help here i have bought a samsung galaxy s with a broken screen glass thinking it would be cheap and easy to replace just the glass, and i have bought the glass from ebay and can tear down the phone but i dont know what to do when i get to the screen how do i seperate it and is their a touch layer under their or what and if anyone could suggest any good tutorials or pictures to help me understand then that would be great because it is not as easy as it seems lol :/ and please dont suggest that i buy a new screen all together because i do not have enough money and i might aswell buy a new phone for the price of an AMOLED lol thnx and plz feel free to PM me
You're wrong from the very beginning
The hardest part to separate in the Galaxy S is the AMOLED screen and the gorilla glass
because they are strongly attached together. It would be very hard if not impossible to separate them without damaging the AMOLED screen
i had this problem but there is help .. i for one done it the hard way and cracked the glass more on the screen very hard to do .. then picked it away with a very small metal pick . look at one of my posts its on here and trust me can be done and then it gets a bit harder putting new glass back on as one the touch dont work right but dw that can be sorted first buy a really thin screen protector then lay that on then lay the new glass over that and touch works fine .. hope this helps but there is a high level of one skill and to a real big risk of fakin up ur screen when picking away at it ..
thnx thats gave me allot more confidence and hope in doing this and succeeding thnx u have inspired me to actually attempt it and i myt aswell because if it works then iv done it the cheep option and if i dont try il never know if the cheap option is possible and achieveable and could uu post a link of your thread please so i can read it much thnx
daleford2k10 said:
i had this problem but there is help .. i for one done it the hard way and cracked the glass more on the screen very hard to do .. then picked it away with a very small metal pick . look at one of my posts its on here and trust me can be done and then it gets a bit harder putting new glass back on as one the touch dont work right but dw that can be sorted first buy a really thin screen protector then lay that on then lay the new glass over that and touch works fine .. hope this helps but there is a high level of one skill and to a real big risk of fakin up ur screen when picking away at it ..
Click to expand...
Click to collapse
how did you crack the gorilla glass more what tool did you use and how plz reply need help thnx
I'm in your same situation, and the solution that daleford2k10 proposes sounds great.
But I have some questions to ask you:
1) Where did u get the glass replacement?
2) What about the touch buttons (menu and back)? Because as I have seen in some disassembling videos they are strong glued. It is possible to get out (or break) the glass above them?
3) Did u tried with a hair-dryer first?
Thanks for your help
Falipene said:
I'm in your same situation, and the solution that daleford2k10 proposes sounds great.
But I have some questions to ask you:
1) Where did u get the glass replacement?
2) What about the touch buttons (menu and back)? Because as I have seen in some disassembling videos they are strong glued. It is possible to get out (or break) the glass above them?
3) Did u tried with a hair-dryer first?
Thanks for your help
Click to expand...
Click to collapse
iv not tried anything yet as the hair dryer is concerned i got my glass from ebay
www (dot) ebay (dot) co (dot) uk/itm/Front-Glass-Lens-LCD-and-touch-screen-not-included-Samsung-Galaxy-S-i9000-/170739151176?pt=UK_Replacement_Parts_Tools&hash=item27c0d8b148#ht_2226wt_1270[/url]
but i dont know if you are a uk resident but you can get it from Hong Kong too and im taking it easy asin trying to get as much info as possible first to do this before i do it oh and i dont think the buttons will cause that much of a problem and anyway if they do break but the screen doesn't its still a win as the buttons would only cost abit and i have also seen some disassembly videos but none separating the glass if you have could you post a link thnx
Finally I got the glass from ebay (the same one as the guy of this post http://forum.xda-developers.com/showpost.php?p=21224865&postcount=238), but delivered from Hong Kong.
I haven't been able to find any videos of this neither... But as both jondale and devonblue4u say, I think it would be just a question of patience and being careful.
Good luck! As I think you will receive your glass first than me (it's going to take around 15 days according to the seller), please post some photos or videos once u do it.
success?
i am about to buy a SGS 1 smashed, but any of you two guys succeed in replacing the glass ONLY? i know i have just bought a dead thread back lol but sorry need to know. thanks
I remember reading somewhere a long time ago that it was done successfully once, but the person who did it had access to the glue used for sticking the screen to the glass, so he wasn't normal by any means. My suggestion? Suck it up and get both the screen and the display. The glass was not meant to be replaceable on its own.
I'm in the process of replacing mine. You can get the glass separated from the amoled using lots of patience,a heat gun, and very thin plastic of some sort. I used a variety of things including a business card, credit card and a very thin steel flat mrasuring tool. The key is heat and moving slowly. Lots of videos on youtube. when you are done there will be lots of glue on the screen, but it comes off by carefully rubbing it. Also, as crazy as it sounds wd40 gets rid of the rest. Saw this on youtube and was skeptical, but tried it and it worked. Cleaned the amoled with rubbing alcohol afterwards. I'm currently using my S with just the amoled while I wait for the new glass too arrive. Also, with the new glass, you won't put glue on the amoled, but around the outsides - again, youtube is yourfriend.
Hello guys, I have a Samsung Galaxy S GT-i9000 ...
I found some code for this machine, and place a code of the camera, and I was without a camera, now I can not go back to the camera, and some systems already installed some android to fix this error .... will someone help me?
very grateful ...: Confuso:
deejayspinz said:
I'm in the process of replacing mine. You can get the glass separated from the amoled using lots of patience,a heat gun, and very thin plastic of some sort. I used a variety of things including a business card, credit card and a very thin steel flat mrasuring tool. The key is heat and moving slowly. Lots of videos on youtube. when you are done there will be lots of glue on the screen, but it comes off by carefully rubbing it. Also, as crazy as it sounds wd40 gets rid of the rest. Saw this on youtube and was skeptical, but tried it and it worked. Cleaned the amoled with rubbing alcohol afterwards. I'm currently using my S with just the amoled while I wait for the new glass too arrive. Also, with the new glass, you won't put glue on the amoled, but around the outsides - again, youtube is yourfriend.
Click to expand...
Click to collapse
I am also looking forward to replace the glass screen on my i9000 but I couldnt find any youtube video on how to do it. Can you give me a link? I would also like to know what kind of glue is needed. Thanks.
I dropped my Samsung Focus and broke the screen glass. The touch screen works fine and i think only the outer screen glass has to be replaced.
I have searched on internet and found DIY repair videos to replace the LCD screen, but couldn't find any info about replacing the outer glass alone. But read its pretty hard to seperate the glass from LCD and replace it !!!
The LCD screen is costing around 120$ and the outer glass is costing 10-16$. I do not want to spend more unnecessarily if i can find a way to replace the outer glass myself.
Also, Samsung Focus is not oficially released here in India here, so i don't think i can approach the samsung itself.
Any help would be much appreciated.
Samsung focus lcd broken
Hi pranav. Same here , i have a samsung focus and lcd + outer glass screen is broken. In one of the screen replacement video i saw , the outer screen and the lcd as one unit and not seperate. Though , i am not completely sure.
Did you find a way to get the lcd or the outer glass for your phone in India?
Please contact me on [email protected]
Did you find a source for the replacement glass only? Please share.
I found only glass on eBay (hongkong or china i suppose). When i spoke to people from service center, all of them were saying it is not possible to replace only glass and they wont do it !!! i i don't know if it is really tough or they do not want to take much pain replacing glass and want to replace the whole LCD set which is easy for them.
And the total LCD + Digitizer + glass kit, i found it for 103$ in eBay US, and for 120 - 140$ in some other repair sites and Amazon.
Waiting for get the replacement from US as it costs less and get it fixed in a samsung service center.
Don't think that's possible. After all, the whole point of "super" in super amoled is that the glass is bonded to the display.
red12355 said:
Don't think that's possible. After all, the whole point of "super" in super amoled is that the glass is bonded to the display.
Click to expand...
Click to collapse
ohh .. din do much reading abt it..
anyways, planning to get a new screen.
Can some one let me know if all the available replacements on eBay or Amazon are original samsung parts or not !!!
HI Frnds,
I also lost my samsung focus S 4G outer screen, phone is working find and the touch also, smooth as it was before. The outer glass got a hair line crack all over the screen. It fell on hard surface and got the crack.
Please help me to get the outer glass.
Thanks Guys! waiting for your reply.
Glass replacement
c0dezer0 said:
HI Frnds,
I also lost my samsung focus S 4G outer screen, phone is working find and the touch also, smooth as it was before. The outer glass got a hair line crack all over the screen. It fell on hard surface and got the crack.
Please help me to get the outer glass.
Thanks Guys! waiting for your reply.
Click to expand...
Click to collapse
I've purchased the glass only and I'm waiting for it to arrive. It was very cheap and if it doesn't work, I'm not going to be too upset for buying it for about $11.00.
bit.ly/JiU1QQ
Amazon also has unit which is the LCD and digitizer already assembled.
amzn.to/ScR33n
I can update if and when I receive my replacement glass from gogotoshop. I find the place questionable but used paypal and can dispute the transaction if it isn't legit.
BTW....removing the glass & digitizer is not an easy task. From attempting to remove my broken screen, I don't think it is possible to remove it from the LCD as the previous posters mentioned.
mine is i937
Thanks for reply, But my phone is Samsung focus s (i937), and I didnot find the front class or Digitizer or LCD or all together.
I have the same problem the front glass broken. other things are ok, I asked on sumsung service center they said the whole thing has to change, I am sure experts can change only the front class.
Anybody has any idea about if I can buy it in India or any site who can ship to India.
or in UK, my frnd is coming from there I will ask him to buy there for me.
Please guys help me.
Thanks,
http://www.ebay.com/itm/New-Black-L...t=LH_DefaultDomain_0&hash=item3f17fbc4a8#shId thats is what i found but they dont ship to india
Mr. Raza said:
http://www.ebay.com/itm/New-Black-L...t=LH_DefaultDomain_0&hash=item3f17fbc4a8#shId thats is what i found but they dont ship to india
Click to expand...
Click to collapse
that is focus not focus s.
Thanks Raza, but this is for samsung focus (i917), and my phone is samsung focus s (i937).
Any update guys. am trying hard to get this upper class in India
keep posted frnds.
SAMSUNG I917 / Focus
Finally got my replacement LCD unit from US eBay. Actual seller is from china though.
Spoke to the Samsung service center guys and they are ready to do the replacement for a nominal service charge....
Going to service center now...
Broken Front Glass lens i937
c0dezer0 said:
Thanks Raza, but this is for samsung focus (i917), and my phone is samsung focus s (i937).
Any update guys. am trying hard to get this upper class in India
keep posted frnds.
Click to expand...
Click to collapse
Hi,
I also have a broken glass lens Focus S, did anyone got replaced the glass lens only here?
Please help???
Glass replacement and new glass glued on
*Learn to remove glass only and glue on new glass*Refurbish glass only on any cell phone and glue and cure with uv lightIcellular.wildapricot.orgYou can remove the glass only on galaxy s2, s3, s4 note 1, note 2, iphone 4, iphone 5 and just about any phone.If you have the right training anyone can do it. My company teaches a refurbish specialist training class on removing and glueing on a new glass. It is two days and includes hands on step by step instruction. We also have a repair shop and we do this repair daily for our customers. We remove the glass, glue on a new one, and cure it with an 100% success rate. So spread the word anyone can do it.
Anybody got Focus S i937 upper glass
Hi Frnds, do anyone got the screen only?
or If I got the screen, is it possible to change? because digitizer and upper screen is bonded and not sure it can be change or not.
UV Glass only replacement
justsavegadgets said:
*Learn to remove glass only and glue on new glass*Refurbish glass only on any cell phone and glue and cure with uv lightIcellular.wildapricot.orgYou can remove the glass only on galaxy s2, s3, s4 note 1, note 2, iphone 4, iphone 5 and just about any phone.If you have the right training anyone can do it. My company teaches a refurbish specialist training class on removing and glueing on a new glass. It is two days and includes hands on step by step instruction. We also have a repair shop and we do this repair daily for our customers. We remove the glass, glue on a new one, and cure it with an 100% success rate. So spread the word anyone can do it.
Click to expand...
Click to collapse
So just like the samsung and iphone models, the focus and focus s can be done the same way? I know for a fact that the galaxy s4 Active is best done by machine. Since ive tried but failed to do one. I have removed the glass from a galaxy s3 mini successfully, should this phone be the same? Please respond quickly!
Thank you