Database Develop

[Q] Stuck on LG logo after CM7! help!

I recently installed CM7 after rooting my phone with Superoneclick and installing Clockworkmod. However, after installation of CM7, i managed to boot up the system, played around with it and realised that i needed to install the google addon as well. So i rebooted the phone to enter into CWM recovery, however the problem started.
My phone is now stucked on the LG logo screen and would not change. I left the phone in that state till the battery went dead. Recharged the phone and it remained on that screen.
Tried to connect the phone to the PC to flash it with smartflash, but it doesnt work at all. I removed the battery and held the volume down button while plugging in the usb cable. All i see is the phone stucked on the white LG logo screen.
Is there any way that i can reformat the contents of the phone or is my phone certified?
All help would be much appreciated!

Power up directly to cwm by pressing power button and volume down key at the same time.
Once in cwm, full wipe including /system and reflash cm and gapps.
Good luck.

I have tried that method as well. Sorry. Forgot to mention it in my initial post. It didn't work. I have tried to pull the battery, hold down the volume down and power button for at least 20 times now. Each time i get the same screen. The CWM menu does not come up.
Any other ways?

audilogic said:
I have tried that method as well. Sorry. Forgot to mention it in my initial post. It didn't work. I have tried to pull the battery, hold down the volume down and power button for at least 20 times now. Each time i get the same screen. The CWM menu does not come up.
Any other ways?
Click to expand...
Click to collapse
Hmm.....if u can't power to cwm directly then perhaps try smartflash to any stock rom.
1. Download any stock rom
2. Start smartflash app from pc
3. In power off mode, just press volume down to boot to software update screen. Start smartflash stock rom.
4. Boot up stock rom
5. Install rom manager and flash cwm from rom manager. (Or download cwm from Rusty! Cwm thread)
6. Boot to recovery
7. Flash cm rom
8. Flash gapps

Remove battery, hold both vol buttons and plug in USB. Screen should stay blank, but Windows will pick up an APX device. Now NVFlash back to stock and start again.

yup, tried the exact method that you suggested too. But it doesnt work. Still gets stuck at the LG logo.

Rusty! said:
Remove battery, hold both vol buttons and plug in USB. Screen should stay blank, but Windows will pick up an APX device. Now NVFlash back to stock and start again.
Click to expand...
Click to collapse
This method worked! But i have another problem, windows found an APX device, tried to install it but failed. It says driver was not found. Do i have to install a specific driver for this to work? Thanks!

Yes, good point: http://android.modaco.com/topic/335...k-rom-release-v10b-dated-1300166062-15032011/

I have managed to flash the phone and it is back working now. Thank you so much for your help rusty and temasek!

Hi, first post, hope the thread is not too old.
Unfortunately this is my best chance.
I have the same problem on my O1:
Updated from mik's beta 6.5.7 to beta 6.5.8 with the clockwork manager, at the reboot, I was stuck on lg logo.
Unfortunately usb + both volume buttons didn't work.
It remains still at the lg logo.
Pressing home + both volume, it repeately reboots.
In every case I can't go in recovery mode, so I can't wipe the system folder.
Any help will be appreciated,
thank for your time!
PS: sorry, maybe thread in p500, cm7 will be more appropriate.

hold power button + volume down button for 5-10 seconds may work, phone will reboot into recovery mode, then you are able to flash a stock rom or restore your nandroid-backup (if you made one)
good luck, hope it helps you

thanks, I saw a useful post here:
http://forum.xda-developers.com/showthread.php?p=18531050#post18531050
Then I proceded as you wrote.
Now I'm stuck at adroid logo, without the chance to wipe cache.
The recovery does not start: loading bar and then forced reboot...
I don't know what to do

nvflash
maybe you try this link
android.modaco.com/topic/335416-nvflash-setup-instructions-drivers-links-active/
Sorry, i don't get the link working, copy it in your browser, then it should work (i'm posting with my phone that's why the link is'nt correct, but it works with browser, i tried it out)

If the link doesnt work, search 'nvflash lg p990 instructions' with google, you'll see the modaco website with the instructions and the download links
Sent from my Optimus 2X using XDA App

Thank you. A few hours ago, I managed to make it working.
Thanks for your answers, I appreciated.

nvflash is the way to go. Always make sure to use the usb ports on your motherboard (back of your computer) and not some usb hub or so.
Had a black screen for 8 hours, not able to boot, flash, recover or anything.
Changed usb port and I was able to flash the phone again.

[Q] Stuck on Htc Logo and can not power off

Hi Everyone;
I unlocked my phone for flashing custom rom. After unlocking i reebooted it and was normal. Then i flashed cwm via htc one toolkit. It was successfull as well. Then i go to cwm and made factory reset + wipe cache + dalvik cache. Then i go to install zip from sd card but i could not find my rom file. Thought, it was deleted while unlocking device. Then decided to reboot phone again to copy rom file into the phone and reboot.
But, when i rebooted phone from cwm, it stuck on HTC Logo( Quietly Brilliant screen). Waited sometime, but nothing happened. Then i tried to power off it and boot into bootloader or recovery. I press and hold power button but it does not respond anyhow. When i am holding power button ,back and home buttons are blinking but nothing happens. Almost five minutes i waited as holding down power button but phone does not power off anyhow. i tried all methods like vol down + power, vol up + power and both volume keys + power. But really nothing happens, just blinking back and home buttons. That's all.
I can not simply power off device. :crying:
I also tried boot device via fastboot commands but it says "waiting for device" means computer does not recognize device.
Guys, i need an urgent help. Please...

just keep trying to reboot via holding power or power+vol down. if it doesnt reboot after 30 sec or so let go then try again. if that doesnt work you will have to wait for the battery to die. once you get to bootloader use all in one toolkit to erace cache. then boot to recovery and you rom should be there if not boot back to bootloader and sideload rom

skinsfanbdh said:
just keep trying to reboot via holding power or power+vol down. if it doesnt reboot after 30 sec or so let go then try again. if that doesnt work you will have to wait for the battery to die. once you get to bootloader use all in one toolkit to erace cache. then boot to recovery and you rom should be there if not boot back to bootloader and sideload rom
Click to expand...
Click to collapse
just keep trying to reboot via holding power or power+vol down. if it doesnt reboot after 30 sec or so let go then try again. if that doesnt work you will have to wait for the battery to die. once you get to bootloader use all in one toolkit to erace cache. then boot to recovery and you rom should be there if not boot back to bootloader and sideload rom
Click to expand...
Click to collapse
First thank you for your quick reply. Unfortunatelly, power+vol down does not work at all. Maybe i tried 50 times.
Anyhow, after battery die. How can i boot into bootloader. I mean, can phone be charged again in this situation? Also, even if i manage to boot into bootloader or recovery how can i put custom rom file into phone. Actually, i did not use sideload or whatever you mentioned before.
I am serouisly confused now and don't know what to do.
Anyhow, as you said, firlst i need wait to battery die i think. Then i will report back whats happen.
Thank you again btw.

Blue_Shine said:
First thank you for your quick reply. Unfortunatelly, power+vol down does not work at all. Maybe i tried 50 times.
Anyhow, after battery die. How can i boot into bootloader. I mean, can phone be charged again in this situation? Also, even if i manage to boot into bootloader or recovery how can i put custom rom file into phone. Actually, i did not use sideload or whatever you mentioned before.
I am serouisly confused now and don't know what to do.
Anyhow, as you said, firlst i need wait to battery die i think. Then i will report back whats happen.
Thank you again btw.
Click to expand...
Click to collapse
yes your not the first person with this problem. hold power+vol down to get into bootloader. press power button in bootloader to get in fast boot mode. use all in one toolkit to erase cache and side load rom. i recommend all in one toolkit because it automates the process. just select the option then follow on screen steps

Good to hear that i am not the first person That means somehow there is a solution i beleive. Still waiting for battery die. even i had 50 percent battery at the begining but still it holds on I never say again htc battery is bad
I exeprienced that stucking on boot logo several times before with my other htc phones but holding power + vol down/up worked always. This is the first time for me that i faced with power button can not power off device.. Well, ,i hope i wish i can handle out this problem. Definetley with your help.
Regards,

I am having the same problem and don't know what to do :crying:
Today I just got my One. Unlocked bootloader, rooted, flashed Android Revolution rom. Everything worked fine for a while... I wanted to reinstall the rom because I wanted to change some options in the installer - I did not wipe because it was the same rom (big mistake I guess!!). After making the installation option changes, when it was done it proceeded to reboot but now I am stuck in a white HTC logo boot loop hell... (with the red text at the bottom that says "this build is for development purposes only" etc). Holy crap I never had a phone that I could not remove the battery. I cannot get this back into recovery or ANYTHING, it just keeps looping... computer recognizes it, no problem with drivers or anything it just doesn't stay connected long enough (because of the constant looping) to be able to use the toolkit.
PLEASE any advice?? Can't even shut it down omg. Do I have a $600 brick here? :crying::crying:

Deeva said:
I am having the same problem and don't know what to do :crying:
Today I just got my One. Unlocked bootloader, rooted, flashed Android Revolution rom. Everything worked fine for a while... I wanted to reinstall the rom because I wanted to change some options in the installer - I did not wipe because it was the same rom (big mistake I guess!!). After making the installation option changes, when it was done it proceeded to reboot but now I am stuck in a white HTC logo boot loop hell... (with the red text at the bottom that says "this build is for development purposes only" etc). Holy crap I never had a phone that I could not remove the battery. I cannot get this back into recovery or ANYTHING, it just keeps looping... computer recognizes it, no problem with drivers or anything it just doesn't stay connected long enough (because of the constant looping) to be able to use the toolkit.
PLEASE any advice?? Can't even shut it down omg. Do I have a $600 brick here? :crying::crying:
Click to expand...
Click to collapse
Did you read the other posts in this thread? The way you do a "battery pull" on this phone is to HOLD the PWR + VOL DOWN button for ~15seconds. Your capactivie buttons will blink, too. On my device, it took exactly 15seconds to reboot. There have been some reports of some phones that get so stuck that you just have to wait until the battery dies and charge it back up.
Alternatively, if the computer is recongizing it, try to adb reboot recovery to try and get into the recovery.

Deeva said:
I am having the same problem and don't know what to do :crying:
Today I just got my One. Unlocked bootloader, rooted, flashed Android Revolution rom. Everything worked fine for a while... I wanted to reinstall the rom because I wanted to change some options in the installer - I did not wipe because it was the same rom (big mistake I guess!!). After making the installation option changes, when it was done it proceeded to reboot but now I am stuck in a white HTC logo boot loop hell... (with the red text at the bottom that says "this build is for development purposes only" etc). Holy crap I never had a phone that I could not remove the battery. I cannot get this back into recovery or ANYTHING, it just keeps looping... computer recognizes it, no problem with drivers or anything it just doesn't stay connected long enough (because of the constant looping) to be able to use the toolkit.
PLEASE any advice?? Can't even shut it down omg. Do I have a $600 brick here? :crying::crying:
Click to expand...
Click to collapse
no. if it turns on you should be ok. try holdind power+vol down to get into bootloader then try toolkit if it just stays on waiting for device press power button to get into fastboot mode from bootloader

skinsfanbdh said:
yes your not the first person with this problem. hold power+vol down to get into bootloader. press power button in bootloader to get in fast boot mode. use all in one toolkit to erase cache and side load rom. i recommend all in one toolkit because it automates the process. just select the option then follow on screen steps
Click to expand...
Click to collapse
hi again. this morning my battery finally out. Then i put my phone to the charger and started it in fastboot mode( that is a good new) Then i left it for 20-30 minutes to charge a little bit for flashing custom rom.Then i went to recovery and started adb sideload. Sideload was succesful and finally came to aroma installer of trickdroid. I chose my installation options and started to flash rom but process was frozen on 10 percent. It was saying unmount system, unmount cahce and both of them has notification as "already unmounted". But installation was not going on. Then again i tried to go back fasboot mode again by press and holding power+vol down but unfortunatelly lights are blinking but nothing happens again. I think i need to wait to battery die again.
Isn't it quite weird? Why power+vol down combination does not work for me anytime? So, do i need to wait for battery die in every frozen? Do you have any ideas or comments ?
Do i need to go back to stock first ?
EDIT : Battery was out again and i tried once more. This time installation (trick droid) was successful but it frozen at the end this time. And unfortunatelly i can not restart (power+vol down) it again again Holy crap, i am really pissed off with this problem.

O..K...Finally, i managed to start my phone and now it works... Especially thank you skinsfanbdh for your support.
But still i don't know how to solve button configuration problem. But anyhow i think i won't need quite sometim to use it I hope someone can find a solution for that later.

Guide me with steps please
Blue_Shine said:
O..K...Finally, i managed to start my phone and now it works... Especially thank you skinsfanbdh for your support.
But still i don't know how to solve button configuration problem. But anyhow i think i won't need quite sometim to use it I hope someone can find a solution for that later.
Click to expand...
Click to collapse
Hi, I have the same problem now and I let my phone die but when I put it to charge and try to go in bootloader, it's doesn't go and gets stuck at the logo again.
Would you please guide me with the steps how u fixed your phone?

Blue_Shine said:
O..K...Finally, i managed to start my phone and now it works... Especially thank you skinsfanbdh for your support.
But still i don't know how to solve button configuration problem. But anyhow i think i won't need quite sometim to use it I hope someone can find a solution for that later.
Click to expand...
Click to collapse
Do u fix it,i have same problem.on Zenfone max.after successfully rom installation i reboot my phone thn it stuck on resurrection remix logo,then i go into recovery,and mount the stock image without wiping.then twrp showed that image installation successful.thn i reboot it in recovery but it stuck on asus logo.what can i do right now?

Fix it
skinsfanbdh said:
no. if it turns on you should be ok. try holdind power+vol down to get into bootloader then try toolkit if it just stays on waiting for device press power button to get into fastboot mode from bootloader
Click to expand...
Click to collapse
Today i fixed it via asus flash tool.with the right steps it can be flash to stock with no problem

What should I do if I can't even get to the boot screen? I tried holding down the power and volume up buttons, but it just restarts and goes back to the same HTC load screen, what do I do????

[Q] Rooting HTC One Mini 2

Is the One Mini 2 possible to root? I've seen a lot saying 'not yet', but it's all fairly old. If so, is there a tutorial/walkthrough somewhere?

koberulz said:
Is the One Mini 2 possible to root? I've seen a lot saying 'not yet', but it's all fairly old. If so, is there a tutorial/walkthrough somewhere?
Click to expand...
Click to collapse
yes root its possible for htc one mini 2.
1- use htc dev website to unlock bootloader and choose all other supported phones. Follow directions.
2-Flash recovery TWRP and flash superuser.zip.
Google it or find in forum tutorials for 2nd step.

I've tried searching, but all I can find is either out of date and stating there's no solution yet, or applies to the original Mini, not the Mini 2.

koberulz said:
I've tried searching, but all I can find is either out of date and stating there's no solution yet, or applies to the original Mini, not the Mini 2.
Click to expand...
Click to collapse
like i said:
go to http://www.htcdev.com/ unlock bootloader. and follow instructions above.
mine its rooted and so lot of others in this forum.
http://forum.xda-developers.com/one-mini-2/help

I got that, it's the "flash TWRP and superuser.zip" that's the issue.

koberulz said:
I got that, it's the "flash TWRP and superuser.zip" that's the issue.
Click to expand...
Click to collapse
1- Download the TWRP Recovery file here and copy it to the C:/Unlock folder created in the Bootloader Unlock Tutorial or the folder you use for HTC unlock
2- Now use the Shortcut “Windowskey + R” and type cmd into the textfield. Press OK to start the Shell.cmd
3- Now we need to navigate to our Unlock Folder by using the command “cd c:/Unlock“ (without “”) and pressing enter
4- Power off your HTC One Mini and boot it back up while holding the Volume Down and Power-Key until you see the bootloader
5- Select “Fastboot” with the volume keys and press power to select
6- Connect your HTC One Mini through original usb to your pc
7- In the Command-Window enter the command „fastboot flash recovery "twrp-2.7.1.0-20140802-memul.img“ (without „“) and press enter
8- The Installation should only take a few seconds and will give a short reports at the end
9- Your HTC One Mini should now have the TWRP Custom Recovery installed
TWRP will try flash SuperUser, it didnt work for me so,
Send UPDATE-SuperSU-v2.02.zip to sdcard and use TWRP to flash it
You must have updated drivers (install htc sync) and original usb cable.

kativiti said:
1- Download the TWRP Recovery file here and copy it to the C:/Unlock folder created in the Bootloader Unlock Tutorial or the folder you use for HTC unlock
2- Now use the Shortcut “Windowskey + R” and type cmd into the textfield. Press OK to start the Shell.cmd
3- Now we need to navigate to our Unlock Folder by using the command “cd c:/Unlock“ (without “”) and pressing enter
4- Power off your HTC One Mini and boot it back up while holding the Volume Down and Power-Key until you see the bootloader
5- Select “Fastboot” with the volume keys and press power to select
6- Connect your HTC One Mini through original usb to your pc
7- In the Command-Window enter the command „fastboot flash recovery "twrp.img“ (without „“) and press enter
8- The Installation should only take a few seconds and will give a short reports at the end
9- Your HTC One Mini should now have the TWRP Custom Recovery installed
TWRP will try flash SuperUser, it didnt work for me so,
Send UPDATE-SuperSU-v2.02.zip to sdcard and use TWRP to flash it
You must have updated drivers (install htc sync) and original usb cable.
Click to expand...
Click to collapse
I got TWRP in. None of the buttons worked. Eventually the screen went blank, I powered back on and just got a 'swipe to unlock' screen. Couldn't swipe, either. So...somehow the touchscreen isn't working?

koberulz said:
I got TWRP in. None of the buttons worked. Eventually the screen went blank, I powered back on and just got a 'swipe to unlock' screen. Couldn't swipe, either. So...somehow the touchscreen isn't working?
Click to expand...
Click to collapse
Try and reboot the phone by holding volume down and power for 10 seconds.

That doesn't do anything. Seems like the only button that does anything is power, and that just turns the screen on if it's off, or to full brightness if it's dimmed (which it does for a second or two before turning off).
I've kept the screen on and managed to run the battery down to 52%. My plan at this point is to run it completely flat, forcing the phone to shut down, then charge it up a bit and see if I can boot. Beyond that, I'm out of ideas and even if I manage to reboot I don't see how TWRP's going to magically start working.
It boots into Android by default, right? And you have to use the Fastboot menu to get to TWRP? No idea how I got to it the first time, actually, and it's been years since I've used it on my old phone.
EDIT: It's TWRP v2.7.1.0. According to the website, the newest version, 2.8.0.0 "[fixes] a bug that caused weird graphics and touch issues". Should I be using this version instead? It doesn't seem to support the Mini 2.

Check this http://forum.xda-developers.com/showthread.php?t=2394744
Try holding power under a bright light..
turn screen off. and under bright light turn it back on. see if it works

No dice. Down to 15% battery at this point anyway, shouldn't be too much longer before it's flat. Then, fingers crossed it works.
How do I get back to TWRP? Fastboot then select 'recovery' (I think I recall that being one of the options)?

koberulz said:
No dice. Down to 15% battery at this point anyway, shouldn't be too much longer before it's flat. Then, fingers crossed it works.
How do I get back to TWRP? Fastboot then select 'recovery' (I think I recall that being one of the options)?
Click to expand...
Click to collapse
just to be on the safe side, i would stay in fastboot and re-flash TWRP

The battery finally went flat, but then as soon as I plugged the phone in it booted into TWRP...which still doesn't work. Have unplugged it again. No idea where to go from here. Tried the "adb reboot bootloader" command from the thread you linked to, and all it did was boot right back into TWRP.

koberulz said:
That doesn't do anything. Seems like the only button that does anything is power, and that just turns the screen on if it's off, or to full brightness if it's dimmed (which it does for a second or two before turning off).
I've kept the screen on and managed to run the battery down to 52%. My plan at this point is to run it completely flat, forcing the phone to shut down, then charge it up a bit and see if I can boot. Beyond that, I'm out of ideas and even if I manage to reboot I don't see how TWRP's going to magically start working.
It boots into Android by default, right? And you have to use the Fastboot menu to get to TWRP? No idea how I got to it the first time, actually, and it's been years since I've used it on my old phone.
EDIT: It's TWRP v2.7.1.0. According to the website, the newest version, 2.8.0.0 "[fixes] a bug that caused weird graphics and touch issues". Should I be using this version instead? It doesn't seem to support the Mini 2.
Click to expand...
Click to collapse
this happened to me, just hold power + vol down + vol up for 10 seconds, phone will reboot.
edit: whilst doing this dont have the usb plugged in. I have noticed having the usb plugged in, a restart sends it straight back to twrp - hence the same issue.

It reboots straight into TWRP when plugged into either the wall or my computer, and just shuts down when not plugged in at all. Can't get it to boot at all, with either volume down + power or just power, but the second I plug it in it boots TWRP.

koberulz said:
It reboots straight into TWRP when plugged into either the wall or my computer, and just shuts down when not plugged in at all. Can't get it to boot at all, with either volume down + power or just power, but the second I plug it in it boots TWRP.
Click to expand...
Click to collapse
ok try, plugging laptop usb port and hold power + vol down + vol up together for 10secs.

Left it plugged in for a while, let the battery build up, and managed to get it booted into Android. So that's a start, at least.
So: fastboot, "fastboot erase recovery" then "fastboot flash recovery twrp.img"?

koberulz said:
Left it plugged in for a while, let the battery build up, and managed to get it booted into Android. So that's a start, at least.
So: fastboot, "fastboot erase recovery" then "fastboot flash recovery twrp.img"?
Click to expand...
Click to collapse
fastboot flash recovery twrp.img should override. i would also download another version just in case that one is corrupted
this is where i got it originally
http://forum.xda-developers.com/one-mini-2/orig-development/recovery-twp-2-7-1-0-one-mini-2-t2801370

You mean another version from another source, or another copy via that link? Not sure where else to get a copy; I assume you get links from the TWRP website after selecting your phone model but the HTC One Mini 2 isn't listed.
I saw somewhere that simply overriding could cause problems, therefore it's best to erase first?

koberulz said:
You mean another version from another source, or another copy via that link? Not sure where else to get a copy; I assume you get links from the TWRP website after selecting your phone model but the HTC One Mini 2 isn't listed.
I saw somewhere that simply overriding could cause problems, therefore it's best to erase first?
Click to expand...
Click to collapse
Check post above this.
TWRP for htc one mini 2 its not yet avaiable in the site, so this is custom.
I have send another file mega https://mega.co.nz/#!C9sRXCAC!OKDm7Df5o95elxtSnF19hiLgsjKn8nq0KplYL9KriIc and changed instructions
or you can get it from the forum http://forum.xda-developers.com/one-mini-2/orig-development/recovery-twp-2-7-1-0-one-mini-2-t2801370
Good luck

[SOLVED][Help] Installing stock recovery causing problems

Hi,
I'm very new to rooting and such and only followed guides a read forum posts to get to where I am now.
My phone is rooted with stock ROM and SU, the bootloader is unlocked but no S-OFF (don't think it's possible on the mini 2 yet anyway). The new OTA update last night installed when I got home and charged my phone, then the phone just shut off and every time I tried to boot it would go straight into TWRP without showing splash screen or bootloader (even when holding power and the volume down button). When it's in this state the touch screen doesn't work and the power button only locks the phone. Holding power + vol down in this state doesn't do anything.
I have to let the power drain completely to get the phone to boot back up but it immediately boots back into recovery and then I can use ADB to force the bootloader to appear, but when I flashed the stock recovery that I found in these boards, it messes up the screen and all it shows is static with some artifacts. I have to let the power drain again to get back into the bootloader, and from the bootloader I can get the android OS to boot but I'd like to fix this completely.
I guess I should also mention that even after flashing the stock recovery the phone will still boot back into TWRP after I let the power drain so I think that means that the stock recovery isn't taking?

The twrp problem you mentioned is known, hope it'll be fixed soon. Are you sure you typed the right command to flash stock recovery? Fastboot flash recovery recovery.img?
If you get stuck, the combination is power button and volume up, not volume down...

gibihr said:
The twrp problem you mentioned is known, hope it'll be fixed soon. Are you sure you typed the right command to flash stock recovery? Fastboot flash recovery recovery.img?
If you get stuck, the combination is power button and volume up, not volume down...
Click to expand...
Click to collapse
Unfortunately I was using the wrong ADB command, I was typing "fastboot boot recovery.img". This seems to have fixed the problem so far but I have yet to try rewriting TWRP back to the phone and I probably won't until theres a fix or unless I need to.
Thank you for your help.

Fierfly said:
Unfortunately I was using the wrong ADB command, I was typing "fastboot boot recovery.img". This seems to have fixed the problem so far but I have yet to try rewriting TWRP back to the phone and I probably won't until theres a fix or unless I need to.
Thank you for your help.
Click to expand...
Click to collapse
I had the same problem. It happens when I reboot with my phone when charging.
You can reboot your phone by holding vol up+power button.

Doogee s68pro not booting up after magisk update, black screen. What can i do to fix this?

So, I recently updated magisk on my phone and as usual to update my phone restarts, but this time it didn't boot up.
I think its in bootloop because when i connect it to my pc with a usb cable it goes on and off also, i cannot access to TWRP.

Can you get to bootloader (fastboot)?
If so you can restore a stock boot image and start over, or try to boot to TWRP with fastboot boot twrp.img and restore the boot image from there and then flash the installer (rename the .apk to .zip as per the new v22+ installation instructions).

I am unable to go into the bootloader or maybe im just doing it the wrong way do you mind guiding me? :/

or maybe i don't have the drivers..

my phone just connects and disconnects, so im not so sure i can go into the bootloader and launch a comand.

Can you shutdown your phone?

i don't think, because it's always turning on and off because the usb sound is going off and on in my pc so i dont really know

You need to use a button combo to get to bootloader or recovery (since you can't boot to Android). A quick web search gives this:
https://droidrecovery.com/doogee-s68-pro-recovery-mode/

thameme said:
i don't think, because it's always turning on and off because the usb sound is going off and on in my pc so i dont really know
Click to expand...
Click to collapse
Exactly like what happen to my device as well

Nope, it does not let me go into the bootloader. Not even with the button combo.

Do you have twrp installed on your phone by any chance? Also a stock boot.img?

First you need to calm down I know how frustrating seeing your device on bootloop and can't even shutdown it ...

i do not have twrp, but i can download a stock boot.img

would you like me to guide you how to fix it i don't have anything to do?

Yes, thank you.

Your device is going on bootloop right now and keep vibrating right?

it's not vibrating. but it probably is in bootloop

lol mine is vibrating while on bootloop okay enough chitchat let's start
vibration is actually good indication for the next process
prepare ADB and USB cable
Now press Power Button and VOL UP at the same time wait for vibration let go Power Button keep holding VOL up for at least 3secs then let go

it's still not vibrating

now press VOL DOWN there's 3 out of 1 chance that you actually made it to fastboot mode ...