Related
Hello!
I'm currently stationed in Singapore and bought a Moto X about a month or so ago from eBay. While I am anxiously waiting for my Moto X to receive the 4.4 update, I realised that the system version (after the previous camera update) is 139.12.35.ghost_row.AmericaMovil.en.PR, which I found to be a Latin America version after some searching on the forums and Googling here and there.
I also found this thread, where OP said that they can be flashed over to either the T-Mobile version. Does this continue to work for the 4.4 updates by T-Mobile or AT&T, and would there be anything else required for flashing? (I saw something about flashing new radios and all, but was quite confused by contradicting explanations and suggestions :/)
Thanks in advance!
// EDIT:
To add on after a bit of searching, I realised that I am allowed to unlock my bootloader, despite claims from the original retailer on eBay that the phone came from AT&T (which is notorious, even here, for their stance on bootloader unlocking). What gives?
I got the same Moto X from a buddy yesterday. I did a lot of searching and also discovered the thread about the phone being flashed to t- mobile.
I fooled the steps on another thread titled " Return to stock 100%" out something like that...
I downloaded the correct Att firmware and with the use of RSDLite, I successfully flashed my Moto X to ATT.... it took less than 10 minutes. And as soon as it booted up, I got hit with the "update available" message ( kit Kat)
Sent from my XT1058 using Tapatalk
Thanks for the information!
I've successfully upgraded my phone to the Verizon version (minus all the bloatware that I hastily blasted off), with root and TWRP. So this is what I did, for future reference:
It seems that AmericaMovil versions are not bound by the AT&T's locked bootloader policies, and other Latin America versions are probably free from the restriction too. So I managed to get my hands on the Motorola Fastboot and unlocked my bootloader. TWRP was installed (remember to use 2.6.3.1 and above for 4.4 support), and then flashed the Verizon system dump available here. Root was installed by TWRP.
After getting on the device and setting things up, I rebooted to recovery to remove lots of bloatware (available in /system/app and /system/priv-app). Had to remove some of them through Titanium Backup as the file names were not always indicative that it came from Verizon. I made the extra step of killing the god-awful boot animation that they had by replacing it with this.
And... that concludes my experience with this, I suppose.
I've been looking through a few threads and I am not comfortable enough to flash the T-Mobile rom over my AmericanMovil one yet.
I can't seem to find step by step instructions on how to do this.. Would anyone like to explain it from the ground up?
My understanding
1) unlock bootloader
2) flash a recovery like twrp or cmw
3) flash the rom that is given in the OG post here http://forum.xda-developers.com/showthread.php?t=2477180
4) this should now give us the t-mobile version of things and we should be able to do the standard OTA from there?
[Q] So can this all be done without ever having to root the phone?
alternetconcept said:
I've been looking through a few threads and I am not comfortable enough to flash the T-Mobile rom over my AmericanMovil one yet.
I can't seem to find step by step instructions on how to do this.. Would anyone like to explain it from the ground up?
My understanding
1) unlock bootloader
2) flash a recovery like twrp or cmw
3) flash the rom that is given in the OG post here http://forum.xda-developers.com/showthread.php?t=2477180
4) this should now give us the t-mobile version of things and we should be able to do the standard OTA from there?
[Q] So can this all be done without ever having to root the phone?
Click to expand...
Click to collapse
I'm not too sure whether flashing via TWRP/CMW will allow you to get OTA, unfortunately. Which is why I went straight for the Verizon system dump. But yes, you can change firmware without ever having to root the phone. Heck, I think there's a guide on restoring mentioned by @plmiller0905 below that will allow you to do it without unlocking the bootloader, even.
RagnaParadise said:
I'm not too sure whether flashing via TWRP/CMW will allow you to get OTA, unfortunately. Which is why I went straight for the Verizon system dump. But yes, you can change firmware without ever having to root the phone. Heck, I think there's a guide on restoring mentioned by @plmiller0905 below that will allow you to do it without unlocking the bootloader, even.
Click to expand...
Click to collapse
I believe the bootloader does have to be unlocked in order to flash a different firmware.
Sent from my XT1058 using Tapatalk
RagnaParadise said:
I'm not too sure whether flashing via TWRP/CMW will allow you to get OTA, unfortunately. Which is why I went straight for the Verizon system dump. But yes, you can change firmware without ever having to root the phone. Heck, I think there's a guide on restoring mentioned by @plmiller0905 below that will allow you to do it without unlocking the bootloader, even.
Click to expand...
Click to collapse
Yeah after doing so more reading.. (at least the way I'm willing to do it) is to just unlock my bootloader and then using RSD Lite (Which i still have no idea what that is / where it is) flash an SBF found here (http://sbf.droid-developers.org/ghost_rcica/list.php)
I guess following this video somewhat http://www.youtube.com/watch?v=Fr0JHSAXJDI#t=15
Does that sound right?
Should I flash the TMO_RETAIL_XT1053_4.2.2-13.9.0Q2.X-116-X-17-57_MR1_CFC.xml.zip
Or just jump straight to the 4.4 version TMO_RETAIL_XT1053_4.4-13.11.1Q2.X-69-3_MR2_CFC.xml.zip
??
As far as I know, the use of RSD Lite doesn't require an unlocked bootloader (at least, that's what it shows in the video you showed me anyway), especially since these are images supposedly signed by Motorola themselves. Let me know if you've found something else?
As for your question on which to flash... I'm not sure, but you'd skip a lot of the hassle if you could flash 4.4 straight, so how about trying that?
RagnaParadise said:
As far as I know, the use of RSD Lite doesn't require an unlocked bootloader (at least, that's what it shows in the video you showed me anyway), especially since these are images supposedly signed by Motorola themselves. Let me know if you've found something else?
As for your question on which to flash... I'm not sure, but you'd skip a lot of the hassle if you could flash 4.4 straight, so how about trying that?
Click to expand...
Click to collapse
Rsdlite is a shell for a flash boot flash supposedly with an XML doing all the steps together. Just makes it easier.
You need unlocked boot loader only to flash an image that doesn't match your current boot loader. So if you have a. At&t phone you can only flash at&t images by rsdlite. But if you unlock your amerimovil phone you can flash any xt1058 image I think. So amerimovil could take say a rogers or at&t or telcel image. Not sure if T-Mobile image will work on a full rsdlite flash as it is an xt1053 image. I think you can flash most of a T-Mobile image by twrp but not by rsdlite not sure
sleepyguy007 said:
Rsdlite is a shell for a flash boot flash supposedly with an XML doing all the steps together. Just makes it easier.
You need unlocked boot loader only to flash an image that doesn't match your current boot loader. So if you have a. At&t phone you can only flash at&t images by rsdlite. But if you unlock your amerimovil phone you can flash any xt1058 image I think. So amerimovil could take say a rogers or at&t or telcel image. Not sure if T-Mobile image will work on a full rsdlite flash as it is an xt1053 image. I think you can flash most of a T-Mobile image by twrp but not by rsdlite not sure
Click to expand...
Click to collapse
So if I flash the at&t image found here (http://sbf.droid-developers.org/ghost_rcica/list.php), would it come pre-loaded with all the bloatware AT&T has even though I'm not using AT&T network?
alternetconcept said:
So if I flash the at&t image found here (http://sbf.droid-developers.org/ghost_rcica/list.php), would it come pre-loaded with all the bloatware AT&T has even though I'm not using AT&T network?
Click to expand...
Click to collapse
yes of course. think about it like if you took a dell windows 7 install CD , and put it on an HP. all the dell customizations would still be there.
obviously since you have unlocked bootloader, once you do the RSDlite you can always flash twrp, and superuser, and delete all that stuff. but then you wouldn't get updates again. i dont think the at&t image is really THAT bad. though i've heard the rogers one is better (though maybe not 4.4 yet)
sleepyguy007 said:
yes of course. think about it like if you took a dell windows 7 install CD , and put it on an HP. all the dell customizations would still be there.
obviously since you have unlocked bootloader, once you do the RSDlite you can always flash twrp, and superuser, and delete all that stuff. but then you wouldn't get updates again. i dont think the at&t image is really THAT bad. though i've heard the rogers one is better (though maybe not 4.4 yet)
Click to expand...
Click to collapse
Yeah unfortunately that's what I thought. Hence why I would of liked to flash the t-mobile image but I'm going to hold off until someone that is a bit more adb savvy then myself tries it out. I wouldn't know what to do if I ended up soft bricking my phone
Well it didn't take long to try it out myself...
It worked out!
I used this thread here http://forum.xda-developers.com/showthread.php?t=2446515
I downloaded the Tmobile 4.4 Image and used RSD.
All you have to do is unlock your BL. (Note: I was completely bone stock with NO root and NO special recovery like CMW or TWRP)
Have all the proper drivers installed, enable USB debugging in developer settings on the phone
Go into Fastboot on the phone
Plug in the phone and just follow the video
I do not take any responsibitliy if you brick your phone. It is fairly easy process and took only a few mins.
Hope this helps!
- deleted because I was sleepy enough not to notice that replies were done on the next page -_- -
alternetconcept said:
I've been looking through a few threads and I am not comfortable enough to flash the T-Mobile rom over my AmericanMovil one yet.
I can't seem to find step by step instructions on how to do this.. Would anyone like to explain it from the ground up?
My understanding
1) unlock bootloader
2) flash a recovery like twrp or cmw
3) flash the rom that is given in the OG post here http://forum.xda-developers.com/showthread.php?t=2477180
4) this should now give us the t-mobile version of things and we should be able to do the standard OTA from there?
[Q] So can this all be done without ever having to root the phone?
Click to expand...
Click to collapse
I've been doing some research on this since yesterday and I've been hesitant on doing it. I saw in your last post that you successfully flashed the TMO 4.4 ROM on your AmericaMovil phone, so I have a few questions for you before I go ahead and do the same:
1. Can you please confirm that your model is XT1058 and not XT1053?
2. Does the TMO ROM have the TMO boot logo and any TMO bloatware?
3. Does the TMO ROM have the Tethering & portable hotspot option under Settings > More?
4. Does the TMO ROM have the Mass Storage option under Settings > Storage > | > USB computer connection?
5. Have you been having any radio problems since you flashed the TMO ROM?
I wonder if I install the ROM in here http://forum.xda-developers.com/showthread.php?t=2477180 using RSDLite, would I get the OTA update to 4.4? The reason I want to install this ROM is because it only flashes system and boot.img without flashing bootloader, modem, logo etc... and I know the XT1058 radio is different from the XT1053 radio, so I've been reluctant to flash a full XT1053 ROM on my XT1058 phone.
But what I also would like to know is if an OTA update would flash a full ROM or not. In other words, if I flash the ROM above and then OTA update to 4.4 and the OTA update flashes the full ROM including the radio, I might as well flash the full 4.4 immediately.
What do you or anyone else think?
I'll answer to the best of my ability. heh
mschumacher69 said:
1. Can you please confirm that your model is XT1058 and not XT1053?
Click to expand...
Click to collapse
Mine was an XT1058, and has been flashed to XT1060. (I didn't notice that T-Mo had a 4.4 ROM on the list, so I went straight for the flashable ZIP for Verizon instead. silly me.)
mschumacher69 said:
2. Does the TMO ROM have the TMO boot logo and any TMO bloatware?
Click to expand...
Click to collapse
At least according to this article, the TMO version shouldn't have any bloatware.
mschumacher69 said:
4. Does the TMO ROM have the Mass Storage option under Settings > Storage > | > USB computer connection?
Click to expand...
Click to collapse
There's no reason why there shouldn't be; I'm seeing it on my Verizon version.
mschumacher69 said:
5. Have you been having any radio problems since you flashed the TMO ROM?
Click to expand...
Click to collapse
I can't say for sure if you'll face any problems, but I flashed the T-Mo radio provided here with my Verizon ROM, and I had no problems connecting to my network in Singapore.
--
I can't answer the rest unfortunately. Sorry. Hope I've helped.
RagnaParadise said:
I can't answer the rest unfortunately. Sorry. Hope I've helped.
Click to expand...
Click to collapse
Thank you for your answers!
Regarding Mass Storage, the reason I'm asking is because I don't have it on my AmericaMovil ROM.
The ROM is basically exactly what you get when you buy the T-Mobile version.
I figured the radios are nearly identical from the AT&T version and the T-Mobile version so my XT1058 is running on the XT1053 radios. There is no bloatware. tethering is there but I'm not sure if t-mobile will allow it. There is NO tmobile logo that comes up on boot. USB connect to computer is there.
As for the radio section again.. I was getting only EDGE in my house before I switched to this ROM (Meaning when I was on the ORIGINAL XT1058 image) and I am still getting only EDGE in my house.. Unfortunately I haven't left my house since yesterday flashing the image but when I'll be back at work in NYC and should see '4G/LTE' over there.
We'll see.
alternetconcept said:
The ROM is basically exactly what you get when you buy the T-Mobile version.
I figured the radios are nearly identical from the AT&T version and the T-Mobile version so my XT1058 is running on the XT1053 radios. There is no bloatware. tethering is there but I'm not sure if t-mobile will allow it. There is NO tmobile logo that comes up on boot. USB connect to computer is there.
As for the radio section again.. I was getting only EDGE in my house before I switched to this ROM (Meaning when I was on the ORIGINAL XT1058 image) and I am still getting only EDGE in my house.. Unfortunately I haven't left my house since yesterday flashing the image but when I'll be back at work in NYC and should see '4G/LTE' over there.
We'll see.
Click to expand...
Click to collapse
Thanks for ur reply! Which network are you on right now?
mschumacher69 said:
Thanks for ur reply! Which network are you on right now?
Click to expand...
Click to collapse
I've always been on T-mobile network. Both when i was on original XT1058 AmericanMovil system version and still on T-mobile when I switched the image to XT1053.
Back on my Nexus 4 though.. I would have HSPA+ in my house.. So I thought it was a bit odd that as soon as I received this phone that I wasn't getting anything other than EDGE..
Would like to root my XT1050, but cannot find the exact firmware to fall back on if something goes awry. My firmware is 139.4.6.ghost_row.ACG.en.US. The closest firmware that I have found is the Brightpoint 139.4.5.ghost_row.LRA.en.US, which is also the XT1050. My Alltel network is CDMA, but not sure if the Brightpoint is. Does anyone think this Brightpoint firmware would work if I needed to re-flash, or would it be missing the proper radios APN's etc....? Alltel was recently purchased by AT&T, and they told me that this phone was an AT&T phone that was LTE ready when they transition over in July. Most other Alltel users will need to replace their phones at this time. I keep looking for Alltel Moto X users here, but haven't seen any yet, as this phone is fairly new for Alltel. Any ideas?
ever find a root method
Was wondering if anyone with the alltel Moto X ever found a root method.
dw777 said:
Would like to root my XT1050, but cannot find the exact firmware to fall back on if something goes awry. My firmware is 139.4.6.ghost_row.ACG.en.US. The closest firmware that I have found is the Brightpoint 139.4.5.ghost_row.LRA.en.US, which is also the XT1050. My Alltel network is CDMA, but not sure if the Brightpoint is. Does anyone think this Brightpoint firmware would work if I needed to re-flash, or would it be missing the proper radios APN's etc....? Alltel was recently purchased by AT&T, and they told me that this phone was an AT&T phone that was LTE ready when they transition over in July. Most other Alltel users will need to replace their phones at this time. I keep looking for Alltel Moto X users here, but haven't seen any yet, as this phone is fairly new for Alltel. Any ideas?
Click to expand...
Click to collapse
the brightpoint fxz is generic cdma. it worked fine on the vzw dev edition moto x with the 4.2.2 gpt/motoboot. not sure whether it will work on a locked alltel device, but there's a good chance that it will, since it is xt1050.
i'd try to root first; the worst that could happen is root will fail. if it succeeds, you can make a nandroid of your stock boot and system before making any further modifications.
if you do need to use the fxz to recover, you should flash only system.img. if that alone doesn't work, you may need to flash boot.img as well. there's really no need to flash anything else.
also, i'd recommend backing up your stock build.prop and replacing the brightpoint build.prop with it if you do flash system.img.
standard disclaimer: i'm not responsible for anything bad that may happen to your device as a result of attempting these things...
really need help
dw777 said:
Would like to root my XT1050, but cannot find the exact firmware to fall back on if something goes awry. My firmware is 139.4.6.ghost_row.ACG.en.US. The closest firmware that I have found is the Brightpoint 139.4.5.ghost_row.LRA.en.US, which is also the XT1050. My Alltel network is CDMA, but not sure if the Brightpoint is. Does anyone think this Brightpoint firmware would work if I needed to re-flash, or would it be missing the proper radios APN's etc....? Alltel was recently purchased by AT&T, and they told me that this phone was an AT&T phone that was LTE ready when they transition over in July. Most other Alltel users will need to replace their phones at that time. I keep looking for Alltel Moto X users here, but haven't seen any yet, as this phone is fairly new for Alltel. Any ideas?
Click to expand...
Click to collapse
I was really hoping someone could upload a link for 139.4.6.ghost_row.ACG.en.US.xml.zip i have accidentally flashed the fsg and modem files for another version of xt1050 and i need alltel's version of these files. plz i can't seem to find a copy of this firmware anywhere and i no longer can get any cdma/evdo signal. all i can do is use a sim card for the time being and considering i am paying for the plan with alltel i'd like to take advantage of my data plan. when i dial *228 it only says call not sent.
aajjs said:
Was wondering if anyone with the alltel Moto X ever found a root method.
Click to expand...
Click to collapse
I have the Moto X XT1050. U can unlock the bootloader using motorola's website. Then flash twrp using fastboot and use the recovery to root.
The recovery will install supersu. All I had to do was download supersu from the playstore. I also installed the cm12.1 nightly. Not bad. Its awesome. Just wish I could activate the thing. Someone told me I could just pop in an already active Verizon 4g SIM and it'll work. Havnt tried yet tho.
Xt1050 twrp
TWRP to link the xt1050
dw777 said:
Would like to root my XT1050, but cannot find the exact firmware to fall back on if something goes awry. My firmware is 139.4.6.ghost_row.ACG.en.US. The closest firmware that I have found is the Brightpoint 139.4.5.ghost_row.LRA.en.US, which is also the XT1050. My Alltel network is CDMA, but not sure if the Brightpoint is. Does anyone think this Brightpoint firmware would work if I needed to re-flash, or would it be missing the proper radios APN's etc....? Alltel was recently purchased by AT&T, and they told me that this phone was an AT&T phone that was LTE ready when they transition over in July. Most other Alltel users will need to replace their phones at this time. I keep looking for Alltel Moto X users here, but haven't seen any yet, as this phone is fairly new for Alltel. Any ideas?
Click to expand...
Click to collapse
I'm in the same position as you man, I want to be 100% sure before doing anything, although mine has the lra firmware. You didn't got 4.4.2 OTA? Why don't you fall back to that one, it's easier to find and since we can unlock the bootloader the official way you don't have to worry..
Can't post the link, it in a filefactory folder
Lol I'm telling you twrp will root, do you need a link?
---------- Post added at 02:48 PM ---------- Previous post was at 02:12 PM ----------
Exe72418 said:
TWRP to link the xt1050
Click to expand...
Click to collapse
Link for TWRP https://mega.nz/#!NZwBVTaY!MD0bqOxQEoXxjcZHFO9yLanH-97W6KYWNhOdGPjfllk
It's the latest
Exe72418 said:
TWRP to link the xt1050
Click to expand...
Click to collapse
Hey you guys stock firmware files located here=> https://androidfilehost.com/?a=show&w=files&flid=44728
If you still need a link for xt1050 twrp=> https://mega.nz/#!NZwBVTaY!MD0bqOxQEoXxjcZHFO9yLanH-97W6KYWNhOdGPjfllk
Love this phone. A little late for the info but better late than never
Sent from my Moto X using Tapatalk
Moto x xt 1050 4.4.2 rooted, bootloader unlocked
Just to confirm guys, the motorola moto X xt1050 with android 4.4.2 is posible to root it and unlock the bootloader and install twrp. The problem that I am still having is that I cant change the apn. I am looking to find a way to do it manually , but so far no success.
If I find anything I will let you know, and if you find something please share it.
Rick
Josephdbrewer25 said:
Hey you guys stock firmware files located here=> https://androidfilehost.com/?a=show&w=files&flid=44728
If you still need a link for xt1050 twrp=> https://mega.nz/#!NZwBVTaY!MD0bqOxQEoXxjcZHFO9yLanH-97W6KYWNhOdGPjfllk
Love this phone. A little late for the info but better late than never
Sent from my Moto X using Tapatalk
Click to expand...
Click to collapse
Install a custom rom. Cm12.1 is pretty smooth.
Cm12.1=> https://download.cyanogenmod.org/?device=ghost
riclau_75 said:
Just to confirm guys, the motorola moto X xt1050 with android 4.4.2 is posible to root it and unlock the bootloader and install twrp. The problem that I am still having is that I cant change the apn. I am looking to find a way to do it manually , but so far no success.
If I find anything I will let you know, and if you find something please share it.
Rick
Click to expand...
Click to collapse
I just flashed cm12 via twrp. It automatically added the apn when I inserted the sim
I purchased it in Aurora, CO from a buddy that said he was using it on T-Mobile.
Everything works great even the LTE on T-Mobile, but from what I read the XT1058 was AT&T's variant of the Moto X and wasnt supposed to support the T-Mobile LTE bands.
I did a little research & found out that it is not a AT&T branded XT1058 and is actually from another country.
After checking the Moto X wiki i came to the conclusion that its the XT1058 model from TIM Brazil
I used it the whole day and noticed an app called "BR Apps" that had a brazil flag in the icon that i just can't uninstall. I can disable it but i want it gone.
I want to root this phone and fiddle with it, but don't know what will work with it.
The bootloader is locked and not sure if it is safe for me to start trying to root this thing.
My biggest question is if it is safe to root this XT1058 the same way as the AT&T or other carrier moto x?
Heres some more info on it.
"Android Version"
4.4.2
"Baseband Version"
MSM8960PRO_BP-2323.031.111.00R
"System Version"
161.44.26.ghost_row.TIM.en.BR
"Build number"
KXA20.16-1.26
tKoHaXoR said:
I purchased it in Aurora, CO from a buddy that said he was using it on T-Mobile.
Everything works great even the LTE on T-Mobile, but from what I read the XT1058 was AT&T's variant of the Moto X and wasnt supposed to support the T-Mobile LTE bands.
I did a little research & found out that it is not a AT&T branded XT1058 and is actually from another country.
After checking the Moto X wiki i came to the conclusion that its the XT1058 model from TIM Brazil
I used it the whole day and noticed an app called "BR Apps" that had a brazil flag in the icon that i just can't uninstall. I can disable it but i want it gone.
I want to root this phone and fiddle with it, but don't know what will work with it.
The bootloader is locked and not sure if it is safe for me to start trying to root this thing.
My biggest question is if it is safe to root this XT1058 the same way as the AT&T or other carrier moto x?
Heres some more info on it.
"Android Version"
4.4.2
"Baseband Version"
MSM8960PRO_BP-2323.031.111.00R
"System Version"
161.44.26.ghost_row.TIM.en.BR
"Build number"
KXA20.16-1.26
Click to expand...
Click to collapse
The AT&T Moto X (and ALL the XT1058 variants) DOES support all the LTE bands that T-Mobile uses. It does NOT support the AWS band which T-Mobile uses for HSPA/HSPA+
All of the XT1058 variants have the same frequency bands....otherwise the FCC would require a different FCC ID.
Anyways, its GREAT that you have a non-U.S. XT1058, because you SHOULD be able to unlock the bootloader from Motos website!!! (AT&T XT1058s can NOT be unlocked through Moto....AT&T won't allow them to give out the unlock codes for the AT&T variants)
If you want root, unlock your bootloader and flash TWRP (which will root the device). Then you're all set! No crazy exploits needed......and you'll be safe with future versions because you won't be using a root 'exploit' that can be patched.
Unlock here: https://motorola-global-portal.custhelp.com/app/standalone/bootloader/unlock-your-device-a
Make sense?
Makes perfect sense. I upgraded from a t-mobile galaxy s3 that was easier to root because of odin software and wasn't 100% sure where I would even start rooting this moto. You pretty much cleared everything up for me. This xt1058 is one of the good ones is what you are saying and its boot loader is ublockable. As far as baseband it should remain the same? Can I flash xt1058/xt1053 ROMs without running into weird issues or should I treat this device like any other US version?
Sent from my XT1058 using XDA Premium 4 mobile app
tKoHaXoR said:
Makes perfect sense. I upgraded from a t-mobile galaxy s3 that was easier to root because of odin software and wasn't 100% sure where I would even start rooting this moto. You pretty much cleared everything up for me. This xt1058 is one of the good ones is what you are saying and its boot loader is ublockable. As far as baseband it should remain the same? Can I flash xt1058/xt1053 ROMs without running into weird issues or should I treat this device like any other US version?
Sent from my XT1058 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yep, pretty much. One of the 'good' ones
It *should* be bootloader unlockable. You will have to try the moto website I linked to see for sure.
You can flash any XT1058 rom safely....the Rogers Canada version seems to be a favorite around here. Some users have reported flashing the XT1053 rom without any issues as well. The XT1058 has 2 additional LTE bands over and above the 1053, and we aren't sure if you 'lose' these bands by flashing the 1053 rom though. This really isn't an issue though, because those 2 LTE bands aren't even used in the U.S. right now.
Do not flash one of the CDMA (verizon, sprint, etc) roms though...
If you flash a different carrier rom you should flash the entire rom (baseband and all). Its not recommended to mix different roms and basebands....and of course you HAVE to be bootloader unlocked -before- you can flash another carrier's rom
samwathegreat said:
Yep, pretty much. One of the 'good' ones
It *should* be bootloader unlockable. You will have to try the moto website I linked to see for sure.
You can flash any XT1058 rom safely....the Rogers Canada version seems to be a favorite around here. Some users have reported flashing the XT1053 rom without any issues as well. The XT1058 has 2 additional LTE bands over and above the 1053, and we aren't sure if you 'lose' these bands by flashing the 1053 rom though. This really isn't an issue though, because those 2 LTE bands aren't even used in the U.S. right now.
Do not flash one of the CDMA (verizon, sprint, etc) roms though...
If you flash a different carrier rom you should flash the entire rom (baseband and all). Its not recommended to mix different roms and basebands....and of course you HAVE to be bootloader unlocked -before- you can flash another carrier's rom
Click to expand...
Click to collapse
Dude thanks a ton! I went to the regular moto website to try and unlock the bootloader but it was a no go. Then i went thru the brazilian site and it worked! Got the booloader unlocked and will flash my first rom in a matter of minutes.
tKoHaXoR said:
Dude thanks a ton! I went to the regular moto website to try and unlock the bootloader but it was a no go. Then i went thru the brazilian site and it worked! Got the booloader unlocked and will flash my first rom in a matter of minutes.
Click to expand...
Click to collapse
Great! If you get an error when flashing to a different carrier rom, let me know and I'll help you get past it.
Also, if you are planning on flashing the 1053 ROM and updating to 4.4.3, you will need to use a new version of TWRP and SuperSU. See here:
http://forum.xda-developers.com/mot...unlocked-twrp-2-6-3-1-android-t2534850/page48
samwathegreat said:
Great! If you get an error when flashing to a different carrier rom, let me know and I'll help you get past it.
Also, if you are planning on flashing the 1053 ROM and updating to 4.4.3, you will need to use a new version of TWRP and SuperSU. See here:
http://forum.xda-developers.com/mot...unlocked-twrp-2-6-3-1-android-t2534850/page48
Click to expand...
Click to collapse
Just flashed the 2.7.0.0 TWRP recovery and installed SuperSu, did a TWRP backup of my system and flashing the T-Mobile stock 4.4.3 Rom from here.
http://forum.xda-developers.com/moto-x/development/rom-stock-flashable-t-mobile-t2773675
Hope all goes well!
EDIT: ALL WENT WELL. Brazil XT1058 Bootloader unlocked, TWRP 2.7.0.0, flashed with XT1053 4.4.3 rooted rom! samwathegreat you are the man!
Hi guys,
I live in Brazil and got a Moto X for my wife, I love it, now considering buy another for myself
She has same version as @tKoHaXoR:
Android Version: 4.4.2
Baseband version: MSM8960PRO_BP_2323.031.111.00R
System version: 161.44.26.ghost_row.TIM.en.BR
Kernel version: 3.4.42-g7a3369f
Build number: KXA20.16-1.26
I'd like to get root and keep the stock ROM, at least for now I won't mess with custom ROMs on it.
My questions:
- once I unlock bootloader and root, I won't get OTA anymore?
- seems 4.4.4 stock is not out for it yet, when it comes I will be able to flash even if I don't get it from OTA?
Sorry it's hard to feel like a noob again, when I did everything possible and flashed dozens of ROMs on my old Galaxy S2
Noed said:
Hi guys,
I live in Brazil and got a Moto X for my wife, I love it, now considering buy another for myself
She has same version as @tKoHaXoR:
Android Version: 4.4.2
Baseband version: MSM8960PRO_BP_2323.031.111.00R
System version: 161.44.26.ghost_row.TIM.en.BR
Kernel version: 3.4.42-g7a3369f
Build number: KXA20.16-1.26
I'd like to get root and keep the stock ROM, at least for now I won't mess with custom ROMs on it.
My questions:
- once I unlock bootloader and root, I won't get OTA anymore?
- seems 4.4.4 stock is not out for it yet, when it comes I will be able to flash even if I don't get it from OTA?
Sorry it's hard to feel like a noob again, when I did everything possible and flashed dozens of ROMs on my old Galaxy S2
Click to expand...
Click to collapse
I'm not 100% sure if it will still get OTA, but most likely you will get a notification on your phone that the update is available. The thing is you will most likely lose root if you accept the OTA update.
I recommend just rooting and installing custom recovery for now and once the update does roll out come back to XDA and look for the rooted 4.4.4 rom and flash it to your device.
Thanks @tKoHaXoR, I unlocked the bootloader yesterday, after messing up a little it's working ok.
Not working great yet, I tried to "integrate updates into system" using Titanium and now "modality services" and "active display" are force closing after boot.
Now trying to find a stock based ROM, it would be nice to have one CWM flashable and deodexed...
Which one did you install?
So, as I understand, there's 2 main types of Moto X: CDMA and GSM
And this XT1058 runs GSM ROMS, so the one from XT1053 should work.
Noed said:
...I'd like to get root and keep the stock ROM, at least for now I won't mess with custom ROMs on it.
My questions:
- once I unlock bootloader and root, I won't get OTA anymore?
- seems 4.4.4 stock is not out for it yet, when it comes I will be able to flash even if I don't get it from OTA?
Sorry it's hard to feel like a noob again, when I did everything possible and flashed dozens of ROMs on my old Galaxy S2
Click to expand...
Click to collapse
Once you unlock the bootloader, and root, you'll still get OTA Updates when the phone's carrier pushes them.
As long as you are stock, and haven't modified too much, you can flash the OTA's. You can be rooted. (for more see -> http://mark.cdmaforums.com/MotoX-OTA.html )
You can always use RSDLite or mFastboot to flash if the SBF (rom) for your phone/carrier gets leaked and put on http://sbf.droid-developers.org/phone.php?device=0 (this site is neither owned, maintained, nor operated by Motorola). They don't have the OTA update files, just the full rom. Based on you earlier posting System version: 161.44.26.ghost_row.TIM.en.BR You have an XT1058 from TIM Brazil.
If you haven't received the OTA yet, but are stock (including stock recovery) and someone shares the OTA zip file for your phone and its carrier, you can manually install it.
Noed said:
Thanks @tKoHaXoR, I unlocked the bootloader yesterday, after messing up a little it's working ok.
Not working great yet, I tried to "integrate updates into system" using Titanium and now "modality services" and "active display" are force closing after boot.
Now trying to find a stock based ROM, it would be nice to have one CWM flashable and deodexed...
Which one did you install?
So, as I understand, there's 2 main types of Moto X: CDMA and GSM
And this XT1058 runs GSM ROMS, so the one from XT1053 should work.
Click to expand...
Click to collapse
Kind of, but not exactly...
We usually don't recommend flashing the ROM from one model/carrier onto another (like flashing an ATT XT1058 with a T-MObile XT1053) because there are risks something could go wrong. That doesn't mean you can't, just means there is a chance you could mess your phone up either in flashing the other rom, or when you try and flash back to stock.
If you are looking for 3rd party or "after market" roms, like CM or such, then yes, usually they don't include modems and such, making them somewhat model independent. (SO you could flash the same CM ROM for GSM on an XT1052, XT1053, XT1058, etc.)
http://forum.xda-developers.com/showthread.php?t=2773675
[ROM][4.4.3]Stock Flashable of the T-Mobile
That is the one you will want to flash
Sent from my XT1053 using XDA Premium 4 mobile app
Thanks again for the help, I flashed this one and worked great:
http://forum.xda-developers.com/mot...0-google-play-edition-4-t2715488/post54328873
i have moto x (xt1058) without at&t logo (ghost_rcica) and i have some problems with wifi and downloading apps from play store.
so, i want to flash stock rom again in my moto x (if that will fix my problems).
i have locked bootloader. pleas help me.
sheikh.sami17 said:
i have moto x (xt1058) without at&t logo (ghost_rcica) and i have some problems with wifi and downloading apps from play store.
so, i want to flash stock rom again in my moto x (if that will fix my problems).
i have locked bootloader. pleas help me.
Click to expand...
Click to collapse
Visit the link in my signature for Stock SBF files...
The view/read/follow -> [GUIDE][VIDEO] Moto X - Return to 100% stock (using RSD Lite OR manual flash)
but i have locked bootloader. can i flash stock firmware with locked bootloader?
KidJoe said:
Visit the link in my signature for Stock SBF files...
The view/read/follow -> [GUIDE][VIDEO] Moto X - Return to 100% stock (using RSD Lite OR manual flash)
Click to expand...
Click to collapse
but i have locked bootloader. can i flash stock firmware with locked bootloader?
help!
sheikh.sami17 said:
but i have locked bootloader. can i flash stock firmware with locked bootloader?
Click to expand...
Click to collapse
i have downloaded the stock firmware. and will flash through manual method. the question is this that can i flash with locked bootloader?
sheikh.sami17 said:
but i have locked bootloader. can i flash stock firmware with locked bootloader?
Click to expand...
Click to collapse
YES you can flash stock Moto roms meant for your model and carrier only.
Also, Never attempt to downgrade.
help me.
i'm currently on 4.4.4 stock and i'm flash stock 4.4.4 again with locked bootloader. i'm not downgrading.
my phone's model is xt1058 i've downloaded brasilian 4.4.4 stock firmware for xt1058. i again ask is that ok to flash with locked bootloader?
thankyou so much for helping.
help me!
KidJoe said:
YES you can flash stock Moto roms meant for your model and carrier only.
Also, Never attempt to downgrade.
Click to expand...
Click to collapse
I'm currently on stock 4.4.4. and i will flash stock 4.4.4 again.
my phone's model is xt 1058. I've downloaded stock Brasilian 4.4.4 firmware
for xt 1058. i had Chat with a motorola agent he said that first i have to
unlock bootloader. i want to confirm again that if i flash without unlocking
the bootloader my will not get Bricked or something like that?
thank you for helping me.
sheikh.sami17 said:
i'm currently on 4.4.4 stock and i'm flash stock 4.4.4 again with locked bootloader. i'm not downgrading.
my phone's model is xt1058 i've downloaded brasilian 4.4.4 stock firmware for xt1058. i again ask is that ok to flash with locked bootloader?
thankyou so much for helping.
Click to expand...
Click to collapse
I don't know exactly what ROM is on a Brasilian XT1058.
On you phone, go App Drawer -> Settings... Make note of what is listed under System Version, Android Version, and build number.
That is what to look for when you are searching for the Stock SBF for your phone. The file name will usually contain parts or all of that info, and possibly the carrier name, or acronym for the carrier name (Verizon might be VZW, Rogers Canada might be RCI, etc)
This is important because if you have a locked bootloader, you can't for example flash an XT1058 from AT&T USA (locked bootloader), with the SBF for an XT1058 from Rogers Canada.
KidJoe said:
I don't know exactly what ROM is on a Brasilian XT1058.
On you phone, go App Drawer -> Settings... Make note of what is listed under System Version, Android Version, and build number.
That is what to look for when you are searching for the Stock SBF for your phone. The file name will usually contain parts or all of that info, and possibly the carrier name, or acronym for the carrier name (Verizon might be VZW, Rogers Canada might be RCI, etc)
This is important because if you have a locked bootloader, you can't for example flash an XT1058 from AT&T USA (locked bootloader), with the SBF for an XT1058 from Rogers Canada.
Click to expand...
Click to collapse
i don't have a at&t phone.
my phone's android version is 4.4.4
system version is 212.44.26. ghost_row. RCI. en. ca
build nunber is KXA21.12-L1.26
that would be really great if u can find correct stock firmware for my phone.
help would be really appreciated.
sheikh.sami17 said:
i don't have a at&t phone.
my phone's android version is 4.4.4
system version is 212.44.26. ghost_row. RCI. en. ca
build nunber is KXA21.12-L1.26
that would be really great if u can find correct stock firmware for my phone.
help would be really appreciated.
Click to expand...
Click to collapse
Right, you have an XT1058 from Rogers Canada... Notice the RCI in the system version (which I also mentioned in my post as a possible acronym)
No offense, but your posts come across as if you are not willing to do anything but ask "tell me how to do this".
I would have a different attitude if you showed me that you took the time to read and try to understand what has been posted.
For example, I KNOW the correct XT1058 RCI CA 4.4.4 SBF is out there on the file factory link, and it has XT1058, RCI CA, 4.4.4 and that system number in its name! but YOU have to take the time to look, IT IS YOUR PHONE.
But no, its been "do it for me."
I have a life. Helping people on these forums is a HOBBY, not a job. I don't have the time to spoon feed each individual. That is why there are guides written (which I gave you links to).
If you can't figure this out, maybe you should play it safe and skip trying to flash your phone. And if you haven't factory reset your phone yet, try that as a first step.
sorry!
KidJoe said:
Right, you have an XT1058 from Rogers Canada... Notice the RCI in the system version (which I also mentioned in my post as a possible acronym)
No offense, but your posts come across as if you are not willing to do anything but ask "tell me how to do this".
I would have a different attitude if you showed me that you took the time to read and try to understand what has been posted.
For example, I KNOW the correct XT1058 RCI CA 4.4.4 SBF is out there on the file factory link, and it has XT1058, RCI CA, 4.4.4 and that system number in its name! but YOU have to take the time to look, IT IS YOUR PHONE.
But no, its been "do it for me."
I have a life. Helping people on these forums is a HOBBY, not a job. I don't have the time to spoon feed each individual. That is why there are guides written (which I gave you links to).
If you can't figure this out, maybe you should play it safe and skip trying to flash your phone. And if you haven't factory reset your phone yet, try that as a first step.
Click to expand...
Click to collapse
sorry but u took me wrong. i have spent too much time in finding the correct firmware but i haven't found. i found at&t firmware which i dont want, and yeah i saw that link and have choose to flash through manual method.
KidJoe said:
Right, you have an XT1058 from Rogers Canada... Notice the RCI in the system version (which I also mentioned in my post as a possible acronym)
No offense, but your posts come across as if you are not willing to do anything but ask "tell me how to do this".
I would have a different attitude if you showed me that you took the time to read and try to understand what has been posted.
For example, I KNOW the correct XT1058 RCI CA 4.4.4 SBF is out there on the file factory link, and it has XT1058, RCI CA, 4.4.4 and that system number in its name! but YOU have to take the time to look, IT IS YOUR PHONE.
But no, its been "do it for me."
I have a life. Helping people on these forums is a HOBBY, not a job. I don't have the time to spoon feed each individual. That is why there are guides written (which I gave you links to).
If you can't figure this out, maybe you should play it safe and skip trying to flash your phone. And if you haven't factory reset your phone yet, try that as a first step.
Click to expand...
Click to collapse
and i have reset my phone many times but no fixes. and the link to sbf files is dead.
sheikh.sami17 said:
sorry but u took me wrong. i have spent too much time in finding the correct firmware but i haven't found. i found at&t firmware which i dont want, and yeah i saw that link and have choose to flash through manual method.
Click to expand...
Click to collapse
Yes, ATT is not right.
sheikh.sami17 said:
and i have reset my phone many times but no fixes. and the link to sbf files is dead.
Click to expand...
Click to collapse
It took me all of 15 seconds to use the link in my signature to the thread with SBF ROM sites, then click the FileFactory site, and find a listing for XT1058_RCI-CA_4.4.4_KXA21.12-L1.26_59_cid14_CFC_1FF.xml.zip
http://www.filefactory.com/file/5z0...4.4.4_KXA21.12-L1.26_59_cid14_CFC_1FF.xml.zip
which most certainly DOES work as I am downloading it as I type.
So again, you are looking for "Do it for me" rather than trying your self. Sorry, but I'm done. Good luck.
thanx!
KidJoe said:
Yes, ATT is not right.
It took me all of 15 seconds to use the link in my signature to the thread with SBF ROM sites, then click the FileFactory site, and find a listing for XT1058_RCI-CA_4.4.4_KXA21.12-L1.26_59_cid14_CFC_1FF.xml.zip
http://www.filefactory.com/file/5z0...4.4.4_KXA21.12-L1.26_59_cid14_CFC_1FF.xml.zip
which most certainly DOES work as I am downloading it as I type.
So again, you are looking for "Do it for me" rather than trying your self. Sorry, but I'm done. Good luck.
Click to expand...
Click to collapse
can u help me a little bit more? in the commands i saw this "fastboot oem config carrier vzw"
but i dont have a vzw phone. so which command should i use?
sheikh.sami17 said:
can u help me a little bit more? in the commands i saw this "fastboot oem config carrier vzw"
but i dont have a vzw phone. so which command should i use?
Click to expand...
Click to collapse
You should be fine not running that command I believe. Flash everything else.
Need Help
Hey Every One! I Need a little Help I Have Bought a moto X At&t but unfortunately i Wipe my custom Rom.. and now its stuck in Bootloader.
Ps.
Bootloader is unlocked
Phone is Rooted
Can You Tell me What can i Do? or any one have Stock Rom for Moto X Xt1058 (At&t). Cuz i have seen lots of links and there are broken..
Regards
Faisal Siddiqui
faisal siddiqui said:
Hey Every One! I Need a little Help I Have Bought a moto X At&t but unfortunately i Wipe my custom Rom.. and now its stuck in Bootloader.
Ps.
Bootloader is unlocked
Phone is Rooted
Can You Tell me What can i Do? or any one have Stock Rom for Moto X Xt1058 (At&t). Cuz i have seen lots of links and there are broken..
Regards
Faisal Siddiqui
Click to expand...
Click to collapse
Download the correct firmware from here: http://www.filefactory.com/folder/dd05c058d3ff8dbe/?sort=created&order=DESC&show=100&page=1
Here you have the XT1058 AT&T 4.4.4 version for example: http://www.filefactory.com/file/48ofsvh148j7/ATT_XT1058_4.4.4-KXA21.12-L1.26_CFC_1FF.xml.zip
Here is a good how-to: http://forum.xda-developers.com/moto-x/general/guide-moto-x-return-to-100-stock-using-t2446515
Make sure you only flash a version that has the same or newer bootloader version! Downgrading can/will brick your device.
Just look up your bootloader version:
30.70 = original 4.2.2
30.71 = 4.2.2 OTA with camera update
30.B2 = 4.4
30.B4 = 4.4.2
30.B7 = 4.4.4
Meaning if you have 30.B7 for example, flashing 4.4.2 is a big no-no
You can find more about it here: http://mark.cdmaforums.com/MotoX-Downgrade.htm
All credits to original posters
I unlocked the bootloader on my XT1096 (verizon) Moto X 2014. Currently running stock 5.1 ROM.
What's the best way to get Marshmallow on? Can I use a ROM from another model? Do I need to flash a recovery? Thanks.
jonnythan said:
I unlocked the bootloader on my XT1096 (verizon) Moto X 2014. Currently running stock 5.1 ROM.
What's the best way to get Marshmallow on? Can I use a ROM from another model? Do I need to flash a recovery? Thanks.
Click to expand...
Click to collapse
The only way to get Marshmallow on a verizon would be with a custom rom that supports CDMA. I know that CM13 supporta CDMA so that one would work.
And while yes you could flash the rom from another model like the xt1095, it would lose verizon signal since the other models are GSM instead of CDMA.
Sent from my XT1095 using Tapatalk
tomas1pit said in the bootloader unlock thread:
"if u want to convert your device dont forget about NON-HLOS.bin and fsg.mbn. That is modem files. U should take them from official 5.1 image for xt1097 otherwise your network wont work"
Would I be able to flash the XT1095 stock MM image and then copy those files over, retaining Verizon signal?
jonnythan said:
tomas1pit said in the bootloader unlock thread:
"if u want to convert your device dont forget about NON-HLOS.bin and fsg.mbn. That is modem files. U should take them from official 5.1 image for xt1097 otherwise your network wont work"
Would I be able to flash the XT1095 stock MM image and then copy those files over, retaining Verizon signal?
Click to expand...
Click to collapse
tomas1pit is incorrect, if you look in other threads of people that have unlocked bootloaders with verizon, they lose signal completely if they convert to another model. He does not realize that xt1096 is CDMA, the NON-HLOS.bin and fsg.mbn apply to GSM.
You can still get signal if you change to another model, but only if you put a sim chip in your phone for AT&T, T-Mobile, etc since those companies are GSM. The problem is that switching firmware makes it incompatible with verizon.
If you plan to stay with verizon, custom roms are your only choice. If you change to a GSM company then you can use the stock firmware from another model.
Sent from my XT1095 using Tapatalk
Roger. Thanks.
It took a few tries to get TWRP on... I had to use crpalmer's custom version, the regular version didn't work. I'll hunt around for a custom ROM. If anyone has any suggestions (as close to stock Android as possible) I'd appreciate it.
jonnythan said:
Roger. Thanks.
It took a few tries to get TWRP on... I had to use crpalmer's custom version, the regular version didn't work. I'll hunt around for a custom ROM. If anyone has any suggestions (as close to stock Android as possible) I'd appreciate it.
Click to expand...
Click to collapse
No problem. Your best bet would be to read the custom rom threads and see if any say they support cdma. Or post in the thread to ask the developer if it does.
The only one I know for sure works with verizon is CM13, since I have read that some verizon users have tried it and it worked for them. I assume that roms that are based off CM might work, but you know what they say about assuming... Anyway good luck finding a rom you like.
Sent from my XT1095 using Tapatalk
I unlocked the bootloader on Verizon xt1096 Android 5.1, installed latest twrp recovery and installed SuperSU and am rooted. Woot. Twrp is super useful! I'd just be careful with what you're flashing of course.
I couldn't get official TWRP to work, but this custom version worked for me:
https://www.dropbox.com/s/t4wbyl4ge807r31/openrecovery-20150308-victara-UNOFFICIAL.img?dl=0
After I installed TWRP, I just flashed SuperSU and got root.
jonnythan said:
I couldn't get official TWRP to work, but this custom version worked for me:
https://www.dropbox.com/s/t4wbyl4ge807r31/openrecovery-20150308-victara-UNOFFICIAL.img?dl=0
After I installed TWRP, I just flashed SuperSU and got root.
Click to expand...
Click to collapse
Have you tried flashing any roms yet for marshmallow?
pianoman102 said:
Have you tried flashing any roms yet for marshmallow?
Click to expand...
Click to collapse
I haven't had time yet.
Same situation. Just recently unlocked the bootloader on my XT1096 (Verizon Moto X 2). Trying to figure out how to get to Marshmallow (stock or rooted) but with Verizon radios. Can't seem to find XT1096/Verizon radios in a flashable zip.
[/COLOR]
mtoomey79 said:
I then took the OTA upgrade to 5.0 which totally hard bricked it.
Click to expand...
Click to collapse
So yeah @jonnythan if you want to help me unbrick my phone...
If there's anything I can do to help, I'd be happy to. There's probably not much I can do, though.
jonnythan said:
If there's anything I can do to help, I'd be happy to. There's probably not much I can do, though.
Click to expand...
Click to collapse
Just a little humor. I have reached out to KidJoe here for some help. I also reached out to MotoCare and they are sending me a new MotoX (for me to tinker with some more).
I would suggest that we need to find a way to get the XT1096 to XT1095, while keeping factory bootloader to accept future OTAs. The VZW radios are out there, just will need to flash them via ADB if/when new OTAs come though.
So for right now, no other custom rom will work with the xt1096 unless somebody makes it specifically or customizes a different rom to suit it right?
CM13 and derived ROMS should work. There are other non-Marshmallow ROMs, I think.
jonnythan said:
I couldn't get official TWRP to work, but this custom version worked for me:
https://www.dropbox.com/s/t4wbyl4ge807r31/openrecovery-20150308-victara-UNOFFICIAL.img?dl=0
After I installed TWRP, I just flashed SuperSU and got root.
Click to expand...
Click to collapse
Where did you get this? All the official TWRP builds throw a mismatched partition size error and won't install.
If I understand correctly, if I'm not using the phone on Verizon I can install any ROM?
crpalmer posted it in the CM12 thread.
I was able to get the latest TWRP installed. Took a few attempts.
i flashed mine with twrp it said the same thing when i fastbbot flashed it but it worked i just booted in recovery any ways and it worked