I have an XT1058 (Rogers version) bootloader unlocked. Running 100% stock Rogers firmware up to this point.
I tried flashing the tmobile 4.4 using the flashall.bat script.
It was working fine until it got to flashing system.img
It never indicated that it got to transferring the file. Everything just froze. After 30 minutes I gave up and disconnected everything. The power had to be pulled from the computer (Windows XP, USB2.0) as it wouldn't shutdown on its own.
Now to the phone, well its not 100% dead but it seems very close. Holding power and volume down doesn't seem to do anything. Holding power and volume up will display the bootloader unlocked screen, but nothing else. My computer can detect a MTP device but its very very slow with the connection. Running adb does not detect any device, at one point the computer did detect a new adb device and installed drivers but I still wasn't able to communicate with the phone.
What are the next steps I should take?
I would plug into a wall charger for a bit to charge it up then rsd.
shane1 said:
I would plug into a wall charger for a bit to charge it up then rsd.
Click to expand...
Click to collapse
Battery was 100% when I started. So far no matter what I do RSD doesn't see any device. I do get a Motorola MTP device driver that wants to install over and over.
It also does show a Mot Composite ADB Interface.
Try holding power and volume down for about 10 seconds then hold both volumes and power should bring you to bootloader menu
OK, its alive again. I knew if I posted in a panic it would come back to life (isn't that how these things always work?)
I kept trying key combinations and finally I got to fastboot. From there I reflashed with back to Rogers firmware with RSD Lite.
So crisis averted, do I try the tmobile 4.4 again?
So crisis averted, do I try the tmobile 4.4 again?
Click to expand...
Click to collapse
Oh hells yeah! If it ends up working, let us know if it enables AWS 1700/2100 bands that you can get on the TMobile model! I'm dying to buy that damn Roger's phone, but I think I'd rather suffer said death than get on another 2 years with them.
Sillux said:
Oh hells yeah! If it ends up working, let us know if it enables AWS 1700/2100 bands that you can get on the TMobile model! I'm dying to buy that damn Roger's phone, but I think I'd rather suffer said death than get on another 2 years with them.
Click to expand...
Click to collapse
OK, tried it again, this time it didn't hang and completed successfully.
So that really is the big question isn't it, will it happen to enable WCDMA on 1700/2100?
Sadly, the answer is no, so far anyway. I have performed the network scan several time in an area where my wife's iphone 5 can see both WCDMA providers on 1700/2100 (Wind and Mobility) So it really looks like its 100% hardware based in terms of the bands it supports. Which makes sense but it really seems like the phone should be able to do it since it can do 1700/2100 LTE.
Steve-x said:
OK, its alive again. I knew if I posted in a panic it would come back to life (isn't that how these things always work?)
I kept trying key combinations and finally I got to fastboot. From there I reflashed with back to Rogers firmware with RSD Lite.
So crisis averted, do I try the tmobile 4.4 again?
Click to expand...
Click to collapse
Can you remenber whats key combination do you use to enter again in the fastboot.?
thanks
sekelink said:
Can you remenber whats key combination do you use to enter again in the fastboot.?
thanks
Click to expand...
Click to collapse
I can't say that I do. I tried various combos for 20 minutes or so. The same problem must have happened to others before. If you're in the same situation I'd try what shane1 suggested earlier in the thread.
Try an Wind or Mobilicity Nano SIM
Steve-x said:
OK, tried it again, this time it didn't hang and completed successfully.
So that really is the big question isn't it, will it happen to enable WCDMA on 1700/2100?
Sadly, the answer is no, so far anyway. I have performed the network scan several time in an area where my wife's iphone 5 can see both WCDMA providers on 1700/2100 (Wind and Mobility) So it really looks like its 100% hardware based in terms of the bands it supports. Which makes sense but it really seems like the phone should be able to do it since it can do 1700/2100 LTE.
Click to expand...
Click to collapse
Hey Steve-x!
Have you tried using an Wind or Mobilicity Nano SIM Card? I'm asking because I have an Galaxy S4 Google Edition (factory unlocked and factory 1700/2100 AWS enable for 3G) and if I try to performe the network scan using an Rogers SIM Card, I can not see Wind or Mobilicity, even if I force the WCDMA 1700 option into ServiceMode. I'd try an Wind or Mobilicity SIM to make sure!
I haven't tried a sim card from Wind or Mobilicity. I did do a network scan with no sim card at all though. I can't say for certain with Android/Moto X but the iphone 5 finds all five networks. I won't be buying a sim from Wind or Mobilicity to find out for certain, neither network is good enough for me.
Steve-x said:
I haven't tried a sim card from Wind or Mobilicity. I did do a network scan with no sim card at all though. I can't say for certain with Android/Moto X but the iphone 5 finds all five networks. I won't be buying a sim from Wind or Mobilicity to find out for certain, neither network is good enough for me.
Click to expand...
Click to collapse
You could go to any Wind Store and try their Nano SIM! You don't have to buy one!
Related
My Nexus was on 5.0.41, all working sweet, then it stopped "finding" the network. No update, flashing or anything was done prior to the problem.
I tried a SIM from another provider, but still - the "No Service" is written on screen, and when I try to search for networks, it says "Error searching for networks".
I then tried the following ideas (nothing helped):
- Reflashed the Radio image.
- downgraded the Radio image.
- Upgraded it again.
- Flashed the Stock ROM (unrooted and rooted).
- Flashed CM5053.
All was done with wipes as needed.
Any suggestions will be more than welcomed!
Can the device just get bricked like that? with no reason?
It sometimes identifies the SIM's provider (Orange for example) but always with No Service.
It sounds like your SIM card slot isn't holding the card in tight enough to make full contact... try putting a business card, cut down to size, between the SIM and the phone's frame (note, not the contacts side, but the back side) to force the SIM down onto the reader tighter.
If that does nothing, not sure what to tell you?
it didn't help
I'm Italian and I have the same your problem .. I only work in 2G GSM'...ve tried to see if you do so?
I opened another tread here Forum
You need a new SIM.
I just had this problem on Friday. The SIM some how falls of the network and your provider network will not allow it to reconnect.
I can't remember, but if I am right Orange is owned/owns by T-Mobile. Hence they have the same network.
The puzzling part about this is why it happens. This is the second SIM I have gone through with my N1, I also had one go with my G1, my sister bought that G1 and the SIM went out again. My mom bought her G1 same day as me and hers has died once. My friend has a MT3G and his has died two times now. I find this extremely annoying.
I tried every suggestion on the internet for repairing or troubleshooting a SIM. It is a waste of time. Well, everything short of dropping it in isoproply alcohol to clean the contact.
I tried a 2G and a 3G SIM on mine, and had the same result, so my problem is different.
My device just doesn't register with the network, no matter what provider or SIM generation I choose.
Can I ask for a RMA if I unlocked the bootloader?
I do not know you definitely do not pass it under warranty
Ryan then you say you clean the contacts of the nexus or the sim with isopropyl
Mine is now doing that as well and so far everything that I tried isn't fixing it. I get it to connect briefly with edge and then nothing. I am going to try a new sim tonight after work and see if that helps, otherwise unsure of what to do after that...anybody got any answers or suggestions?
I've been suffering from this... have an RMA coming but I got mine to work. Make sure you also have CDMA preferred on there or whatever the default is. If it says unknown you have to reboot the radio somehow. I pulled my battery, waited 5-10 seconds. Then i went and checked airplane mode on and off. Then i checked the service menu again. I can't remember if i had to pull the battery another time but it came back from "unknown" to cdma preferred. You can also try turning the radio on and off via the service menu. Finally select your radio bands for your region by pressing the menu button under phone information again in the service menu and select radio bands. I'm not sure if automatic is a good or bad idea but it couldn't hurt testing it if you still have some issues even after selecting your region specific bands. After this you should be able to maybe search and register or you may need to turn the radio on and off again via airplane or the service menu. I played around with it alot to get it running again.
Also I'm tmobile usa using the one for t-mobile bands. I'm not sure if CDMA preferred is a world wide setting or if its gsm or something else.. but the bands are specific to your region definitely.
The wife and I have Atrix HD phones that we bought used but in great condition a couple months ago. We purchased the Straight Talk at&t compatible micro sim kits from walmart.com and set up our service. We previously had Samsung Captivates also on Straight Talk and they worked flawlessly. I put in my APN settings and I get data and MMS perfectly but occasionally I get a red triangle where my signal bars should be and my phone says "Emergency Calls Only" and I will wait 30 seconds or so and my signal returns. There is no steady decline in signal that leads up to this. It goes from like 4 bars to a red triangle with a cross inside it.
I live in a fair sized town and have always had 3 or more bars of at&t service with phones in the past so I do not think its an issue with poor coverage. I am attaching pictures of my APN settings.
Any help would be appreciated.
Applehater87 said:
The wife and I have Atrix HD phones that we bought used but in great condition a couple months ago. We purchased the Straight Talk at&t compatible micro sim kits from walmart.com and set up our service. We previously had Samsung Captivates also on Straight Talk and they worked flawlessly. I put in my APN settings and I get data and MMS perfectly but occasionally I get a red triangle where my signal bars should be and my phone says "Emergency Calls Only" and I will wait 30 seconds or so and my signal returns. There is no steady decline in signal that leads up to this. It goes from like 4 bars to a red triangle with a cross inside it.
I live in a fair sized town and have always had 3 or more bars of at&t service with phones in the past so I do not think its an issue with poor coverage. I am attaching pictures of my APN settings.
Any help would be appreciated.
Click to expand...
Click to collapse
I'm having the exact same issue since switching to to the 4G LTE micro sim. It only seems to happen on mine when I'm connected to Wifi though. I get the red triangle intermittently. This never happened to me until I went from the old sim to the new one. Can't find anything on it yet.
same thing
The same thing is happening to me here as well but using a Net10 LTE sim card (same as straight talk basically). I notice it the most after I complete a phone call. It takes a minute or two to regain service again. This is really annoying. Would like to see a solution to this problem.
So I worked with Straight Talk support for about 5 days, back and forth, bounced to several reps throughout and nothing substantial has come of it. It seems a little better after they made "adjustments" to my account as they put it, but I still get disconnected from mobile data when on wifi.
Don't get me wrong, their support people were very responsive and seemed to genuinely want to help me, but in the end they said "your ticket has been open for more than 24 hours so it has been closed. If you continue to have issues please open a new ticket." Anyone else have any luck on this?
I also was having this problem found that if you edit existing att apn (phone needs to be rooted)with sqlite editor it seems to work fine.
tether also works fine this way.I am still not able to get lte to work with straight talk even with new sim.
Just to follow up. As usual, it seems with ST support, one rep tells me they have some things they can try once I call back on another line and then I get a new rep who says nothing can be done until 10 people complain about the exact same issue I'm having. I'm assured this is an isolated incident...
I went ahead and purchased a new SIM card (looks different than the first LTE card I had) in case I had a faulty SIM. Worked flawlessly for a day and now it's back to the same issue of cutting out completely throughout the day.
same problem here on wifi get red triangle (especially after phone call).
More since i switched from 4g sim card to lte sim noticed that data disconnect from time to time like make impossible to watch video flawlessly...
with old 4g was yes only 4g but never loss a bite....could watch anything also streaming tv.....now it is impossible.....
the end of the month going to switch to old sim and see if the problem is in the new sim cards they tried may be to limit access or is in the new service doesn't matter what sim card you possess..
we'll see...
htchd2fix said:
same problem here on wifi get red triangle (especially after phone call).
More since i switched from 4g sim card to lte sim noticed that data disconnect from time to time like make impossible to watch video flawlessly...
with old 4g was yes only 4g but never loss a bite....could watch anything also streaming tv.....now it is impossible.....
the end of the month going to switch to old sim and see if the problem is in the new sim cards they tried may be to limit access or is in the new service doesn't matter what sim card you possess..
we'll see...
Click to expand...
Click to collapse
Switching to my old sim was my first thought to. However when I tried it didn't work. I called ST and they informed me that once you switch sims, the old one can never be reactivated. On top of that they don't offer the non LTE sims anymore. Such a pain. Hope you have better luck though.
pentjaksilat8 said:
Switching to my old sim was my first thought to. However when I tried it didn't work. I called ST and they informed me that once you switch sims, the old one can never be reactivated. On top of that they don't offer the non LTE sims anymore. Such a pain. Hope you have better luck though.
Click to expand...
Click to collapse
Some one could correct me if I'm wrong here but I'm pretty sure this is a result of ROMS using a 4.4 rom. Modem crashes. If you want to test it run a Stock ROM... If you are already using a completely stock ROM then Idk what to tell you. But same thing happens to me using any version besides stock. And yes only when on WiFi
metalmike6 said:
Some one could correct me if I'm wrong here but I'm pretty sure this is a result of ROMS using a 4.4 rom. Modem crashes. If you want to test it run a Stock ROM... If you are already using a completely stock ROM then Idk what to tell you. But same thing happens to me using any version besides stock. And yes only when on WiFi
Click to expand...
Click to collapse
I'm on a 100% stock ROM, I haven't unlocked my boot loader, just rooted.
pentjaksilat8 said:
I'm on a 100% stock ROM, I haven't unlocked my boot loader, just rooted.
Click to expand...
Click to collapse
Then unlock your bootloader and try flashing different radios from the different stock fastboots we have. Depending on the fastboot I can have next to none or almost full in my bedroom. For me, ATT JB is in the middle, JB Mex Retail is the best, Bell ICS is the worst. ATT ICS was about the same as ATT JB.
skeevydude said:
Then unlock your bootloader and try flashing different radios from the different stock fastboots we have. Depending on the fastboot I can have next to none or almost full in my bedroom. For me, ATT JB is in the middle, JB Mex Retail is the best, Bell ICS is the worst. ATT ICS was about the same as ATT JB.
Click to expand...
Click to collapse
For the time being, I just switched to Aio and so far so good with LTE coverage and no disconnecting issues. If they return I'll try different radios as you suggested.
So I've been with Aio for about a week now and everything is working great (knock on wood). I've had 2 mobile data drops at work with Wifi turned on, but they only lasted for a second and I do have really bad reception here inside the building. Outside of that no issues at all so far. I'll update if anything changes.
I see this question asked a few times within other treads but wasn't ever really answered clearly in my situation. I have successfully network unlocked my Sprint HTC One. When I put the sim in I get no errors and dialing 4636 brings me to the menu where I can change to wcmda preferred..gsm only... etc.. The phone reads the phone number off the sim and lists it on this page as well. Heres my issue I have verified that phone will cover the same bands where I am so that should not be an issue. I can not get a signal with this phone with 2 different sims. I made sure I did all the obvious things with the settings, the APN's, flashed different radios, and tried different options is the 4636 menu. Ive used different roms as well...When I go to select or search for my network both options are grayed out.... I can connect to Verizon and I can connect to sprint towers but no Dice on ATT. I am currently on version 4.1.2 and have tried all available radios. Has anyone had success in the new York New Jersrey PA area with using this phone on ATT. If so what is the setup you are using.
KoolAidBigMan said:
I see this question asked a few times within other treads but wasn't ever really answered clearly in my situation. I have successfully network unlocked my Sprint HTC One. When I put the sim in I get no errors and dialing 4636 brings me to the menu where I can change to wcmda preferred..gsm only... etc.. The phone reads the phone number off the sim and lists it on this page as well. Heres my issue I have verified that phone will cover the same bands where I am so that should not be an issue. I can not get a signal with this phone with 2 different sims. I made sure I did all the obvious things with the settings, the APN's, flashed different radios, and tried different options is the 4636 menu. Ive used different roms as well...When I go to select or search for my network both options are grayed out.... I can connect to Verizon and I can connect to sprint towers but no Dice on ATT. I am currently on version 4.1.2 and have tried all available radios. Has anyone had success in the new York New Jersrey PA area with using this phone on ATT. If so what is the setup you are using.
Click to expand...
Click to collapse
The Sprint HTC one has blocked the carrier id's for domestic use aka att. You can however if your s-off you can flash the initial release radio the first radio when the Sprint HTC was released and it will allow you to connect to domestic carriers.
I'm in Ohio so not too far from you and I can pick up T-Mobile and att using the initial release radio, it is the only radio I could get to pick up signal.
Here is the first radio released http://d-h.st/HHD
Im currently s-off and flashed that radios. When I select network connection the two options are still grayed out. Could the rom choice make any difference ?
Same here....help please
Sent from my HTCONE using XDA Premium 4 mobile app
pyrobo0by said:
Same here....help please
Sent from my HTCONE using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I am having the same issue with my Sprint HTC One. I've tried everything mentioned above and no one has answered. Are you guys still having this issue? And if not what did you do to fix it. I have a Sprint HTC One with S-Off, Unlocked Bootloader, the Radio that is listed here and the latest ViperOne 5.7.0 ROM. Thanks!
EDIT: My phone is unlocked and I have been using T-Mobile for the past month just fine, and want to try AT&T.
wireproof said:
I am having the same issue with my Sprint HTC One. I've tried everything mentioned above and no one has answered. Are you guys still having this issue? And if not what did you do to fix it. I have a Sprint HTC One with S-Off, Unlocked Bootloader, the Radio that is listed here and the latest ViperOne 5.7.0 ROM. Thanks!
EDIT: My phone is unlocked and I have been using T-Mobile for the past month just fine, and want to try AT&T.
Click to expand...
Click to collapse
I have figured out a way to make AT&T work with the phone. When you place a Sprint or Verizon sim into the phone, it will immediately unlock the network search options that are normally greyed out. I click automatic select and immediately remove the sim and replace it with my AT&T one. Even though the phone complains that the sim was removed, I can click ok, then quickly push the automatic select again before it greys out. I then wait a minute or so until it fails to find a network. I then quickly click the network search option. The notable thing at this point is the only network that shows up is MARITIME. if I click on that, it registers me to AT&T. I have tested the phone and it works great. But it seems to bump me off the network at some point. I dont know if its poor reception or the ROM itself doing it. And if I restart the phone, I lose it as well. So I have to repeat the steps again to get back on AT&T. But the thing to know here is that the phone will work with domestic carriers with no problem. Its a matter of locking to AT&T and staying there. Surely one of the brilliant brains on these forums can figure out how to keep it working. I basically stumbled onto this by playing around with it.
joem789 said:
I have figured out a way to make AT&T work with the phone. When you place a Sprint or Verizon sim into the phone, it will immediately unlock the network search options that are normally greyed out. I click automatic select and immediately remove the sim and replace it with my AT&T one. Even though the phone complains that the sim was removed, I can click ok, then quickly push the automatic select again before it greys out. I then wait a minute or so until it fails to find a network. I then quickly click the network search option. The notable thing at this point is the only network that shows up is MARITIME. if I click on that, it registers me to AT&T. I have tested the phone and it works great. But it seems to bump me off the network at some point. I dont know if its poor reception or the ROM itself doing it. And if I restart the phone, I lose it as well. So I have to repeat the steps again to get back on AT&T. But the thing to know here is that the phone will work with domestic carriers with no problem. Its a matter of locking to AT&T and staying there. Surely one of the brilliant brains on these forums can figure out how to keep it working. I basically stumbled onto this by playing around with it.
Click to expand...
Click to collapse
Good job finding that. When it kicks you off of AT&T's network it did that to me when I had T-Mobile as well, so it's not just AT&T. Glad you were able to get AT&T to work on your phone tho, kudos.
So as of saturday my unlocked TMobile Note 4 stopped working as a phone, and won't let me make calls.
Information:
-Was on Dr. Ketan L3 version of his rom when it stopped working
-Using the N910T on AT&T
-IMEI is fine and not damaged, both numbers match (using *#06#)
-It shows bars, but when I go to make a call "Not Registered On Network"
What I've Done:
-Flashed Stock Firmware via Odin (Autoboot, and F.Time Rest checked)
-Factory Reset after odin flash
-Checked APN
-Set on LTE/WCDMA/GSM
-Searched for Networks, finds them, but when I choose AT&T it takes forever and then finally kicks me out and then in notifications, I get the "Not Registered to Network"
-Did the remove the battery thing, and removed sim
-Went to AT&T and got a new sim, worked for 1hr (sporadically) and then went back to "Not Registered on Network"
-At the store I was on phone with AT&T tech trying to troubleshoot the problem and that is when it was working shortly
-Called T-Mobile and checked to see if they blocked my IMEI number, nope they didn't, couldn't help me out further than that
-AT&T was showing that it was a Note 4 so not having that coming up as a Blackberry issue that some reported, so that's not it
-*#0011# shows service limited, but it is unlocked and everything is fine, the IMEI is good, and all is well but the limited service
-Put it in Airplane mode and woke it back from there after 5+minutes
-cleaned the connectors on the sim (new sim anyways so shouldn't really need them)
I'm running out of options, the only thing I can think of being the problem is that I might have started out using this phone on COD2, and when I flashed a COG2 firmware it didn't like that and so my phone's account settings didn't fully transfer.
Also I was messing around with the bands settings (*#2263#) what should they be on? Automatic, LTE/GSM only, or what?
Settings should be on automatic. One more thing to try is go for a drive with the phone, at least 5 miles from your house, and see if it does this when connected to other towers. I had this same issue years ago and it turned out to be a malfunctioning tower by my house.
If it still does it on other towers, then it may be hardware-related
kabuk1 said:
Settings should be on automatic. One more thing to try is go for a drive with the phone, at least 5 miles from your house, and see if it does this when connected to other towers. I had this same issue years ago and it turned out to be a malfunctioning tower by my house.
If it still does it on other towers, then it may be hardware-related
Click to expand...
Click to collapse
Thanks, yeah it kicks in randomly for like a minute and then dies, I take it to my parent's house (about 10 miles away) and along the way I get a good signal, but then when I reach their house, back to nothing. I was using it just fine the week prior. I partially blame Dr. Ketan, ever since installing his rom, I had multiple issues. I since uninstalled it and tried going back to stock. Any idea on what a good "safe" band setting is? I have that settings set to automatic, but if there was a good "safe" band that would be great. A common LTE tower. Even when I do connect or get connected, I can't register on that network, my phone won't let me. I've tried that. The bars drop to zero. I damaged my antenna wire (white one) and I just replaced it with a new one I purchased, but the hacked together one seemed to be doing the same quality job as the new one is. It shows the signal, but as soon as you try tying it down to a network it rejects it. I was afraid that when I flashed the stock image via odin it removed the unlock, but it was still there. I just hate that now I have a $500 pda, when it was a phone and now i'm relegated to using a f*ing flip phone.
i think your antenna cable is damaged. the only way to know that is be close to a tower, and see if your work or not.
bought and replaced with new ones, I get full bars, in my bedroom, but apparently they're tied to Tmobile since when I try to register it to AT&T they magically disappear, but when I close the app, they come back at the same strength level. I can't register them to Tmo since the sim. Yet my phone is telling me it's unlocked (*#0011#), IMEI = PASS, 1;
I think the prob is due to the different frequencies.
Your baseband would not be tied to a rom(ie Dr Ketan) Unless that rom contains Modem.bin
Your apn needs to be att if that's your Sim obviously.
International version has a different chipset. .. I know it's not your case. .
But it's open to any Sim. ..
I can say this.. I have a N2 unlocked (tmob) I run an Att Sim it works but the sig is really spotty... COD6/ COG2 may not be lining up frequency wise with your att Sim. ..
Try rolling your baseband back even further. .
Flashvetrin
Any clue on to what i should use for best results? Like 850/1900 or 900/2100? What is a good LTE band? Where could I find a map of LTE bands used by carriers, I know how to get to that secret menu and manually change it to see if I get better results?
dcoke said:
Any clue on to what i should use for best results? Like 850/1900 or 900/2100? What is a good LTE band? Where could I find a map of LTE bands used by carriers, I know how to get to that secret menu and manually change it to see if I get better results?
Click to expand...
Click to collapse
Well I would think automatic is out for sure.. the other prob would be after reboot the chipset will search for the default.. but I could be wrong.
I do not know what the numbers would be for band identification.
You may get lucky when calling Att and ask for someone in a higher tier. To give you some numbers for frequincies .
But you have ruled out hardware correct??
By putting a tmob Sim in????
Cuz I know you posted you did antenna work..
And I do know you said you get bars then it fades..
The fact it fades and doesn't lock into even a G band for example. Just leads me to believe the apn can't lock down based on the frequincie and the built in lte chipset...
It would be nice to just flash an att modem wouldn't it?? But don't even think about it.. lol you'll soft brick..
I wish I had a better solid answer you. You may just start testing those different bands and see if you get closer to a lock.
Flashvetrin
U rock, lol. Thx man
My Tricked Out N910P
But what could have happened that made it crap out like that since it was working just fine beforehand for 2 solid months on custom roms and what not? That's the frustrating part, I've been flashing different modems on my phone, but none have been successful. Apparently there are 3 different N910T, how do you know which ones to play with? I flashed N910T(3) bands, that failed, I did try N910A, obviously failed. Then I lost my IMEI number, got terrified, tried reflashing EFS in TWRP, nothing. Then reflashed COG2 bands, it came back. Is there an app on the Playstore that would definitively tell you if your network chip is damaged? I wouldn't know what to look for.
Have you taken apart the Note 4, what are all those contact points, are those antenna things? One of those were damaged, they're like folded metal spring boards with gold tips (same kind of thing that is used to install a qi receiver, same design). I took my tweezer and fixed it, but could that be the culprit, since on the surface, it seems like the network is fine. Works really well in WCDMA, but not much else. I was able to make calls using GSM only, but my signal was 1 bar and the audio quality was questionable, so I left it alone for 10 minutes on that hoping it would force a reconnect. This is frustrating, since I wasted $500 on this phone and not having it work after two months means now I'm back to a featureless phone.
Thanks for your advice thus far. Flashing different modems hasn't been working out well, I just wished I could remember what baseband version the guy had the phone on when I first got it? I thought it was COD6, it was definitely on Lollipop, but if it's a 910T(2) would I know, how would I know?
How do you flash NON_HLOS and modem.bin at the same time in Odin? I know Modem does bands, but what does Non-Hlos do? I thought i read LTE, so if those aren't in sync and on two different versions could that be the issue? I extracted them from the full TAR firmware files.
dcoke said:
But what could have happened that made it crap out like that since it was working just fine beforehand for 2 solid months on custom roms and what not? That's the frustrating part, I've been flashing different modems on my phone, but none have been successful. Apparently there are 3 different N910T, how do you know which ones to play with? I flashed N910T(3) bands, that failed, I did try N910A, obviously failed. Then I lost my IMEI number, got terrified, tried reflashing EFS in TWRP, nothing. Then reflashed COG2 bands, it came back. Is there an app on the Playstore that would definitively tell you if your network chip is damaged? I wouldn't know what to look for.
Have you taken apart the Note 4, what are all those contact points, are those antenna things? One of those were damaged, they're like folded metal spring boards with gold tips (same kind of thing that is used to install a qi receiver, same design). I took my tweezer and fixed it, but could that be the culprit, since on the surface, it seems like the network is fine. Works really well in WCDMA, but not much else. I was able to make calls using GSM only, but my signal was 1 bar and the audio quality was questionable, so I left it alone for 10 minutes on that hoping it would force a reconnect. This is frustrating, since I wasted $500 on this phone and not having it work after two months means now I'm back to a featureless phone.
Thanks for your advice thus far. Flashing different modems hasn't been working out well, I just wished I could remember what baseband version the guy had the phone on when I first got it? I thought it was COD6, it was definitely on Lollipop, but if it's a 910T(2) would I know, how would I know?
How do you flash NON_HLOS and modem.bin at the same time in Odin? I know Modem does bands, but what does Non-Hlos do? I thought i read LTE, so if those aren't in sync and on two different versions could that be the issue? I extracted them from the full TAR firmware files.
Click to expand...
Click to collapse
Heres
A simple method for COD6
And try odin 3.07
I need to think about this some more and get back to you...
This is a partial firmware.. it consists of the modem and bootloader COD6.
Also to rule out damage if you can get a T Mobile Sim put it in the device and see if it locks down a signal....
Flashvetrin
That was my next move, not having any real income but disability and little coming from that, I thought that was the next logical step too. I'll get a tmobile to go sim and try it see if it can't lock on to that, and see if that doesn't set it on the right path. Have you heard of other people having COG2 issues on AT&T unlocked? Maybe that was the problem, something there broke the connection. I don't know, but whatever it is, I can't thank you enough, you've at least given me more options to try that I couldn't think of on my own. I'll try that file.
dcoke said:
That was my next move, not having any real income but disability and little coming from that, I thought that was the next logical step too. I'll get a tmobile to go sim and try it see if it can't lock on to that, and see if that doesn't set it on the right path. Have you heard of other people having COG2 issues on AT&T unlocked? Maybe that was the problem, something there broke the connection. I don't know, but whatever it is, I can't thank you enough, you've at least given me more options to try that I couldn't think of on my own. I'll try that file.
Click to expand...
Click to collapse
You are the first of this kind that I'm aware of.. in regards to this issue..
Make sure you read the detail in if your device bootloops, to reboot recovery and flash the Rom.. if you want flash the Rom in the op that I've linked you to.
Wipe sys/dal/cach/data..
And flash it can't hurt.. [emoji16]
I really hope a Tmob Sim and or COD6 gives you results...and good ones at that.. [emoji2] [emoji106]
Flashvetrin
Got the sim card, $65 for that crap, and it didn't work. Called T Mobile customer service, explained my situation and how I was calling on another phone on another carrier and they insisted on calling me back on the broken not working phone. I guess I'm just screwed, and lost $500, which like I said, I can't afford to have. It's just so frustrating. I also tried the COD6 partial firmware, and nothing there also. I'll try t-mobile again. The only and last option I have, if possible, is to try to relock my phone and re-unlock it since there isn't any real way to tell if my GSM is damaged. I think my unlocked status got damaged when my phone upgraded to COG2, and since it's in that weird limbo state I can't use my phone. Do you know how to relock it?
Edit: When I look at my IMEI Number through *#06# it shows that the last two digits (independent of the actual IMEI number, since that matches everywhere) to the right of the "/" as 14, yet through "about device" it shows my imei version as 10. I assume that the 14 in the "06" screen is the version it's reading off the phone, could that be causing the issue? How would you even fix that? I don't know. but thanks again, you've been helpful.
I am contemplating purchase of one of these phones, and tried entering some of their IMEI numbers in the imei checker at https://www.t-mobile.com/resources/bring-your-own-phone , and was shocked to find they are ALL described as "Incompatible".
This is a bit confusing after the articles saying the AT&T and Verizon versions would not work after Jan 2021 but that the T-Mobile version would continue working. I tried looking for a later article saying that support for the T-Mobile version this model was being cancelled but could not find any such announcement.
Is that IMEI checker correct? Or is it because the samples I checked may not have gotten the last modem update installed from T-Mobile?
Is anyone still using this phone (specifically the T variant) on T-Mobile in USA? I'm assuming that last update will be important, but does this still work once it is installed?
If yes to the above, do phone calls work as VoLTE, or is it doing the fallback to 2G?
I've also seen threads about enabling more LTE bands, has anyone done that on this phone? In particular is it possible to add support for B71 (600MHz), or is this radio hardware just too old to allow that?
Thanks much, I would really like to know whether I can use this phone or if I would need to find a different model.
https://swappa.com/blog/3g-network-shutdown/ Your phone is fine.
SM-N910T with 2ETI1 OTA modem update works fine. 4g/LTE Data, WiFi Calling works. Does not drop out of 4G/LTE for voice. SM-N910V w/ MODestROM v11 (6.01 TW-based N910VVRU2CQI2 ) w/ a vzw 2CTI baseband update, has working 4gLTE data, but no WiFi Calling, or VoLTE (falls back to 2g, but I still have 2g coverage here, so it's usable, if not optimum. Here's the thing: on the VZW phone, if I set the the salescode to TMB, suddenly VoLTE works, but the Setup pages/menus/statusbar are screwed up, so it's not really useable. Here's where it gets REAL interesteing. On a VZW phone w/ VZW 2CTI1 baseband, & VZW BL, flashed with a custom TMB ROM (trltetmo_N910TUVU2EQI2_Stock_Deodexed, debloated, but still TW), EVERYTHING works. But it's not stable, it periodically loses 4g/lte. What it tells me is that the VZW h/w is NOT THE PROBLEM. I've been at this all day, everyday since VZW turned off CDMA on 01/01/23 and killed my service here. Be warned: If you go down this path, you're gonna be mostly on your own. A LOT of dead links, 'retired' devs, etc. Everyone except you, me, and three other people here have long since moved on from this awesome phone. I'll help you if I can. I bought an SM-N910T , but the damn usb port is dead. Already changed the charging board, not the problem. It's the mobo. If I could identify the usb chip (if it's not the 805 itself, I'd change it. So I have a phone with no adb that I can't unlock/root. I'd much rather get my VZW phone fully working on TMB, since I'm heavily invested in the MODestROM. Haven't given up yet. But search my posts, you'll hear the deafening silence, lol.
Seeing this forum has so little activity, on 1/21 I ended up getting a used Moto E6 (XT-2005-3 is a tmobile aka carrier unlocked MetroPCS version). While overall this is not as nice a device and has fewer features than Note 4, it does cover what for me are the essentials - removable battery, SD card slot, support for 5.8GHz wifi. Best of all, it supports B71 which will be helpful for, well, making phone calls!
I still ponder someday getting one of these as a hobby device, but that would be second place to the E6 for use as a phone, and won't be for a couple more months yet (too many expensive household issues are taking their toll on my "toy" budget right now).
ForestCat said:
SM-N910T with 2ETI1 OTA modem update works fine. 4g/LTE Data, WiFi Calling works. Does not drop out of 4G/LTE for voice.
Click to expand...
Click to collapse
Thank you, this was the part I needed to find out. With that in place, the only thing missing would be the B71 coverage but the E6 is already in place for that.
Re your Verizon adventures, I have no experience with any of that. What I read about T-Mobile dropping support for the verizon version in the last network update is all I know, and I don't have the skills to dispute what they say there. The best I could do is offer some links to threads on this forum but on double checking them it seems you've already been there and got no answers.
The only thing I see that might help you with that is if you could update just the t-mobile modem without disturbing the verizon bootloader. I see you tried that but it didn't stick when using Odin. I don't know if it would be any different using SmartSwitch that seemed to work for MarineWonder as he posted at https://forum.xda-developers.com/t/...pgrade-on-jan-29th-2021.4224237/post-87464609 ?
Then again he may have been putting it on a t-mobile phone rather than mixing with the verizon bootloader so who knows?
My guess since it has been so problematic for you on the verizon phone is that you may need to only use a tmobile phone since that may be the only way to get the last t-mobile modem update. Bummer that the one you bought has a dead usb port. How are you charging it? Is there any chance you could return it to the seller since it came pre-broken? Then put the refund money toward another, hopefully working, tmobile phone? And would that MODestROM work on a non-verizon phone?
The only other thought I had is there are apps to connect to ADB over wifi. Sadly most of these need root. The ones that don't, seem to need at least once using a usb connection to do the "adb tcpip 5555" command to set it all up. . . . how annoying that it is all so circular!
There is also https://telnetd.en.aptoide.com/app?store_name=apps&app_id=59202144 , maybe a telnet connection could do the "adb tcpip 5555" command instead of using the USB connection? Sadly the documentation (at https://waxrain.com/docs/010.html ) appears to be written in Chinese, and I never had much luck with google translate.
The N910T still supports VoLte.. It is still compatible with cellular networks.