Database Develop

My D3 died! :(

:crying:
Opened bike race when the screen froze while opening the game (dark screen).
Pulled the battery but when I boot the screen goes on after 3 secs, stays on for 2 secs then goes into dim mode (i can see it's still on).
However my phone doesn't boot since I don't get any whatsapp messages. Normally it should boot to SIM screen but other apps should run.
X+power or M+power doesn't change much.
I'm guessing mobo/cpu fail.... any ideas?
:crying:
edit: It turns on when I put in the charger without battery! Dead battery?

If you put the battery flat on a table does in spin well. Batteries bulge when they are done. The better the spin the worse it is. It's odd the behaviour that can happen with a end of life battery
Sent from my DROID3 using xda premium

Well now I'm not so sure what it is.
When I put the cable in without battery the M logo appeared and then the charge screen with a ? in the battery (because there was none)
Then I put the battery in and it started charging.
After a while I tried to turn it on but same problem - just a black screen when power it, no logo whatsoever.
Now I can't get it to work without battery either...
edit: I don't think it can be the battery, because the screen stays on (it has power apparently) and it doens't work with cable connected either
But I also don't see it being the screen as it never vibrates like it does when you boot it.
How did it just show the charge screen before and now it doesn't??

I made a vid of what happens when I power it:
https://dl.dropbox.com/u/22072961/Droid 3/Video0067.mp4

The Droid 3 and Bionic are similar phones, and it turns out that the Bionic will not boot up without a battery - it will hang at the Moto logo even if plugged in. See this thread at androidforums.com: http://androidforums.com/motorola-d...via-adb-unable-boot-up-phone.html#post5463741
So, it may be that you just need a good battery pack in order to get to Recovery/Bootloader/Fastboot etc. if the phone will not start or start to Safestrap.

doogald said:
The Droid 3 and Bionic are similar phones, and it turns out that the Bionic will not boot up without a battery - it will hang at the Moto logo even if plugged in. See this thread at androidforums.com: http://androidforums.com/motorola-d...via-adb-unable-boot-up-phone.html#post5463741
So, it may be that you just need a good battery pack in order to get to Recovery/Bootloader/Fastboot etc. if the phone will not start or start to Safestrap.
Click to expand...
Click to collapse
Ye, except my phone doesn't even show the motorola logo, and I can't even get to the bootloader menu
edit: and it doesn't explain why I was able to get to the charge screen without battery at first, but not now

Right now I'm having the same problem, I could enter safetrap for now (after 10 attempts)

Emacore said:
Right now I'm having the same problem, I could enter safetrap for now (after 10 attempts)
Click to expand...
Click to collapse
:crying:
I tried at least 30x now no difference
The worst part is using my Samsung Jet "Smarter than a smartphone". Which isn't even close to a smartphone because it doesn't have any of the OSes = no apps

In my XT860 in its power when it reaches the lockscreen, restarts or shuts.
When I put it to charge my battery shows 0% and charging. When I go to Safestrap-after several attempts-, battery shows 99% or sometimes 80%.
I think the cpu wants to leave the world of technology :crying:
edit: yeah, now i get infinite bootloops in the M DualCore LOL

Emacore said:
In my XT860 in its power when it reaches the lockscreen, restarts or shuts.
When I put it to charge my battery shows 0% and charging. When I go to Safestrap-after several attempts-, battery shows 99% or sometimes 80%.
I think the cpu wants to leave the world of technology :crying:
edit: yeah, now i get infinite bootloops in the M DualCore LOL
Click to expand...
Click to collapse
Well at least yours sounds like a software issue. Just wipe

No, I can not turn it on, I can not enter bptools, I can not use RSD, nothing! Just lucky I managed to get a few seconds to safestrap

hi Doubleyp
try to see if it starts with a factory cable (like the Team black hat one) (no need for battery)
if it starts then its the battery

gierso said:
hi Doubleyp
try to see if it starts with a factory cable (like the Team black hat one) (no need for battery)
if it starts then its the battery
Click to expand...
Click to collapse
I tried the stock cable that came with my phone (USB) but nothing happens. Screen doesn't even go on.
The light next to the microUSB does go on.
But my phone has never booted with USB (0.5A). When my battery was 0% I always needed a socket charger because it wouldn't go on and charge with USB
When I then insert battery and try again with stock cable same happens as in the video

DoubleYouPee said:
I tried the stock cable that came with my phone (USB) but nothing happens. Screen doesn't even go on.
The light next to the microUSB does go on.
But my phone has never booted with USB (0.5A). When my battery was 0% I always needed a socket charger because it wouldn't go on and charge with USB
When I then insert battery and try again with stock cable same happens as in the video
Click to expand...
Click to collapse
The stock cable and a factory programming cable are not the same
Sent from my DROID3 using xda premium

Endoroid said:
The stock cable and a factory programming cable are not the same
Sent from my DROID3 using xda premium
Click to expand...
Click to collapse
Ah I see. Well I'm not in the US so getting one would be a PITA
I'm gonna try my spare battery (original battery) tomorrow. It that doesn't work it must be hardware related because I haven't flashed or done anything to it so it's not softbricked or something.
edit: it team blackhat do send to europe? How would this be different from trying another (working) battery?

Try cutting a USB cable open, hook the red wire to the + of the battery and - to the black and let it charge that way. Also, do you have any MicroUSB charger? I have one for a BB Bold I used to have that delivers I think 1.25A and it could charge my phone from dead (obviously not now with the flex cable having a rip in it).

DoubleYouPee said:
I tried the stock cable that came with my phone (USB) but nothing happens. Screen doesn't even go on.
The light next to the microUSB does go on.
But my phone has never booted with USB (0.5A). When my battery was 0% I always needed a socket charger because it wouldn't go on and charge with USB
When I then insert battery and try again with stock cable same happens as in the video
Click to expand...
Click to collapse
The little light next to the USB port is the 'It's still alive" light that Moto put in when the battery is completely dead. It's to let you know that the phone *is* charging, just not high enough to boot the phone (i.e. when you let the battery completely die).
WHY they did not make it a standard charging light (like the D1 and D2) I don't know, but that's the only time it comes on. A quick flicker on USB plugin, or when the battery is dead. The light goes out when it gets enough power to boot up.

Skreelink said:
The little light next to the USB port is the 'It's still alive" light that Moto put in when the battery is completely dead. It's to let you know that the phone *is* charging, just not high enough to boot the phone (i.e. when you let the battery completely die).
WHY they did not make it a standard charging light (like the D1 and D2) I don't know, but that's the only time it comes on. A quick flicker on USB plugin, or when the battery is dead. The light goes out when it gets enough power to boot up.
Click to expand...
Click to collapse
Well, it's not charging because there's no battery , the light it still on
I really dont see how its the battery because when I put it in without cable the screen turns on and stays on for as long as I keep the battery in. So it HAS power. Today I'm getting my spare battery and we'll see I guess..... don't have my hopes up

My daughters D3 was doing the same thing,me being not ready to dig into a phone yet ,took to a local repair shop, they checked it out and found it had a bad LCD,should get back Friday, sorry for the bad news,just thought you would like some insight.
Sent from my Droid 3 using xda app-developers app

Buckaru11 said:
My daughters D3 was doing the same thing,me being not ready to dig into a phone yet ,took to a local repair shop, they checked it out and found it had a bad LCD,should get back Friday, sorry for the bad news,just thought you would like some insight.
Sent from my Droid 3 using xda app-developers app
Click to expand...
Click to collapse
Thanks. But should it turn on when the LCD is bad? It doesn't even boot else It would vibrate once.
Can anyone confirm that the phone should boot when I remove the LCD alltogether? Else it might be a bad LCD or loose connector

[Q] Touchpad won't boot

I cannot get my sisters TP to boot. I guess she let it die completely, so now when I plug it in, all I get is the home button to blink back and forth. If I try to turn it on, I get the red battery with a lighting bolt icon, then a white plug icon, and when I plug it in from there I get the "To reliably charge" message. I don't have the original ac adapter or cable because she lost it. I have already reflashed the A6 firmware. Also, if I leave it plugged it with the home button flashing, after about 20 minutes or so, the flashing stops for a few seconds, then starts for a few seconds, then stops again and so on and so forth. Is there anything else I should try? Or is this thing dead?

See if you can get an OEM cable or a Touchstone.

pr621 said:
I cannot get my sisters TP to boot. I guess she let it die completely, so now when I plug it in, all I get is the home button to blink back and forth. If I try to turn it on, I get the red battery with a lighting bolt icon, then a white plug icon, and when I plug it in from there I get the "To reliably charge" message. I don't have the original ac adapter or cable because she lost it. I have already reflashed the A6 firmware. Also, if I leave it plugged it with the home button flashing, after about 20 minutes or so, the flashing stops for a few seconds, then starts for a few seconds, then stops again and so on and so forth. Is there anything else I should try? Or is this thing dead?
Click to expand...
Click to collapse
Leave it charging for a long time, 24 hrs +, it should charge.
Good luck.

original charger
pr621 said:
I cannot get my sisters TP to boot. I guess she let it die completely, so now when I plug it in, all I get is the home button to blink back and forth. If I try to turn it on, I get the red battery with a lighting bolt icon, then a white plug icon, and when I plug it in from there I get the "To reliably charge" message. I don't have the original ac adapter or cable because she lost it. I have already reflashed the A6 firmware. Also, if I leave it plugged it with the home button flashing, after about 20 minutes or so, the flashing stops for a few seconds, then starts for a few seconds, then stops again and so on and so forth. Is there anything else I should try? Or is this thing dead?
Click to expand...
Click to collapse
You need to find an original charger or maybe a compare able 2amp Carter will work. A standard phone charger or USB port on your computer is not powerful enough to charge it.

Check amazon it shouldn't cost more than $10

I have another tablet charging block that is 5.0v and 2 amps, but when I use that all it does is make the home button flash then stop then flash again. I left it charge on my computer overnight to try and get it to trickle charge. When I woke up the home button wasn't flashing and when I try to turn it on, the red battery comes up for a second then the white plug icon. I guess I'll see about getting an OEM cable, hopefully that works.
UPDATE: I got it into "recovery" mode? It was plugged into my PC so I held power and vol up until my pc recognized it. But it's showing up as palm in the device manager, and no drivers seem to work for it.
UPDATE 2: My sister found her OEM charger and now it seems to be actually charging. Thanks for the help, I'll let you know if this doesn't work.

Yep, usually issues like that are because of not using the OEM Charger.

pr621 said:
I cannot get my sisters TP to boot. I guess she let it die completely, so now when I plug it in, all I get is the home button to blink back and forth. If I try to turn it on, I get the red battery with a lighting bolt icon, then a white plug icon, and when I plug it in from there I get the "To reliably charge" message. I don't have the original ac adapter or cable because she lost it. I have already reflashed the A6 firmware. Also, if I leave it plugged it with the home button flashing, after about 20 minutes or so, the flashing stops for a few seconds, then starts for a few seconds, then stops again and so on and so forth. Is there anything else I should try? Or is this thing dead?
Click to expand...
Click to collapse
Only hope is original charger or Touchstone
Sent from my cm_tenderloin using Tapatalk 2

Battery dead, bricking issue
I have had several charging issues with my Touchpad. I am using ClassicNerd Butta OS. IF I am using the Android OS (Butta) and I turn off the Touchpad and then plug it in to charge it will restart the Butta OS. When this happens the Touchpad discharges instead of charging. So, when I come back later the Touchpad is dead and it takes a lot of messing around to get it going again. To prevent this I always turn off the Touchpad when I am using the Butta OS but I don't immediately attach the charging cable. Instead, I wait a bit. Then when I plug in the charging cable I immediately switch to the WebOS operating system. The device seems to charge well using WebOS. When it is done charging I unplug the cable and turn the device off. Next time I restart the Touchpad I let it boot to Butta. Then when it discharges to 80% or so I start the process again as stated. Sticking with these procedures has prevented the no-charge / no-boot issue from reoccurring. I also no longer charge the Touchpad at night. Instead, I charge it in the morning or during the day and only leave it on the charger for an hour or two until it is fully charged. It is my understanding that technique should result in longer battery life and better (longer) charge in the battery.
When my Touchpad battery has gone completely dead it is a real pain to get it to charge up the battery again. When the batter is totally dead the device will not boot into any OS or allow me to even get to the boot loader program. Takes a lot of messing around to get it to start charging again. Though I have been able to, eventually, get it to boot into WebOS and start to charge. But this was not an easy process by any means.
Also, I would agree that you really need to get a stock charger with the cable for your Touchpad. Using a different charger could damage the battery in your Touchpad and/or cause the battery to charge too slowly.
Good luck!
pr621 said:
I cannot get my sisters TP to boot. I guess she let it die completely, so now when I plug it in, all I get is the home button to blink back and forth. If I try to turn it on, I get the red battery with a lighting bolt icon, then a white plug icon, and when I plug it in from there I get the "To reliably charge" message. I don't have the original ac adapter or cable because she lost it. I have already reflashed the A6 firmware. Also, if I leave it plugged it with the home button flashing, after about 20 minutes or so, the flashing stops for a few seconds, then starts for a few seconds, then stops again and so on and so forth. Is there anything else I should try? Or is this thing dead?
Click to expand...
Click to collapse

My Hp TouchPad tablet came today and I was told when bidding that it was doing exactly the same thing as mentioned here. I have the OEM charger and cable.. I'll let you know when I can get it straightened out and I hope it is a good one.. Thanks for the info..

While on the OEM charger it booted and I selected webos for the tptb to reflash A6, but soon after it was off charger it went back to the battery icon. battery life low I guess? I selected shutdown. Let it charge over night and see what happens.
Many thanks to many members who are so helpful...

Bionic will not power on

Hello:
I recently got a use Bionic with a cracked screen, no battery, and no sim card. I replaced the screen and bought a non-oem extended battery with cover. When I got everything and fixed it, the phone worked for 3 days. During this time I did a factory reset plus cache wipe then updated everything to latest software and firmware. I had it plugged into my computer to charge over night but on the third day after being plugged in to the computer to charge, I tried to turn on the phone and the white light started blinking at me. I had a wall charger that I use for my Samsung Galaxy Precedent (current using phone) to charge it over night again but all I would get is the Motorola M logo and a then the battery charge status. I search some forums and some one said that my battery was bad so I got an OEM extended battery and an OEM wall charger with dock station. So at this point, the only thing I can access is the recovery screen but that only happens when it is pugged into the wall charger but when I hit the power button I get the Motorola M logo and the battery status which say 5%. Once the screen goes dark again I hit the power button and the battery says 100%. But once I unplug it, I get nothing. Not even the recovery screen. When I plug it into my computer I get the white light again but this time it stays solid. It still will not power up, or even access the recovery screen while plugged into the computer as well. Any suggestion on what might be wrong and what I might do to fix it? Please help someone!

[Q] Strange (hard?) brick

Hi,
After many years of enjoying this magnificent phone the disaster came.
The phone discharged overnight and switched off. In the morning I had to send some texts, so plugged the wall charger into USB socked (a weak one ~500mA), after few moments a charging icon appeared and stated that battery has 1%. Ok, I really had to send those messages: I've pressed the power button and phone started to boot.
Sony logo: OK, purple wave, OK...
After 10-20 seconds it suddenly switched of, red LED started to blink.
I thought: OK, system startup needs a lot of power, maybe a charger is too week to keep up.
So I left phone for few more minutes to charge, but without success.
That was the last time I saw screen was on.
Phone is a C6903, running on a stock, rooted 14.6.A.1.236 with the recent XZRecovery.
Bootloader has been unlocked.
For the moment I've tried everything but opening back and doing the testport-trick.
When I connect the power only red led blinks (I left the phone charging overnight, no change).
When I try to enter flash mode: nothing happens but red blinking light.
When I try to start phone nothing happens at all.
But there is still hope:
I connected the phone to 2A charger using a magnetic cable.
Then I've connected normal USB cable to my PC, strange thing started to happen:
When I pressed volume Up (even after few minutes of connecting power+usb) the phone suddenly jumped to fastboot mode (blue led, it was discovered by PC, fastboot terminal was functional)
When I press power button, phone vibrates for a second, then the led pattern changes to: 1s red followed by 0.1s green, then long red, then it repeats...
I'm still unable to enter any recovery nor flashmode...
I'd really appreciate any help, have you got any ideas left how can I revive my phone?

Qba_S said:
Hi,
After many years of enjoying this magnificent phone the disaster came.
The phone discharged overnight and switched off. In the morning I had to send some texts, so plugged the wall charger into USB socked (a weak one ~500mA), after few moments a charging icon appeared and stated that battery has 1%. Ok, I really had to send those messages: I've pressed the power button and phone started to boot.
Sony logo: OK, purple wave, OK...
After 10-20 seconds it suddenly switched of, red LED started to blink.
I thought: OK, system startup needs a lot of power, maybe a charger is too week to keep up.
So I left phone for few more minutes to charge, but without success.
That was the last time I saw screen was on.
Phone is a C6903, running on a stock, rooted 14.6.A.1.236 with the recent XZRecovery.
Bootloader has been unlocked.
For the moment I've tried everything but opening back and doing the testport-trick.
When I connect the power only red led blinks (I left the phone charging overnight, no change).
When I try to enter flash mode: nothing happens but red blinking light.
When I try to start phone nothing happens at all.
But there is still hope:
I connected the phone to 2A charger using a magnetic cable.
Then I've connected normal USB cable to my PC, strange thing started to happen:
When I pressed volume Up (even after few minutes of connecting power+usb) the phone suddenly jumped to fastboot mode (blue led, it was discovered by PC, fastboot terminal was functional)
When I press power button, phone vibrates for a second, then the led pattern changes to: 1s red followed by 0.1s green, then long red, then it repeats...
I'm still unable to enter any recovery nor flashmode...
I'd really appreciate any help, have you got any ideas left how can I revive my phone?
Click to expand...
Click to collapse
Hi, this just happened to me, my phone has been dead for over 4 weeks with just the red led blinking. i tried the test point thing with no success at that point I gave up but last week i decided to get a new genuine battery and it worked it booted up. Your battery is just completely dead thats why it won't boot up!

tilakpatel22 said:
Hi, this just happened to me, my phone has been dead for over 4 weeks with just the red led blinking. i tried the test point thing with no success at that point I gave up but last week i decided to get a new genuine battery and it worked it booted up. Your battery is just completely dead thats why it won't boot up!
Click to expand...
Click to collapse
Thanks for the info! I've ordered a replacement battery already.
I'll open my phone today and measure all voltages. I'll keep you updated.

Good luck

tilakpatel22 said:
Good luck
Click to expand...
Click to collapse
Yup! That was it (at least I think so, I don't have new battery yet)
The Al part of positive battery terminal was broken: I have no idea why, maybe because of age, oxidation and high currents that were drained from this LiPo cell...
Anyway I've managed to temporarily join two broken Al parts, kernel and recovery booted successfully.
Now I need to wait for a replacement battery.
Phone is alive again, thanks tilakpatel for help!
But the magnetic cable trick might be useful in other hardbrick cases: just connect magnetic charger, connect normal USB cable to PC and hold volUp. Phone should be able to enter fastboot even with completely drained battery...

Qba_S said:
Yup! That was it (at least I think so, I don't have new battery yet)
The Al part of positive battery terminal was broken: I have no idea why, maybe because of age, oxidation and high currents that were drained from this LiPo cell...
Anyway I've managed to temporarily join two broken Al parts, kernel and recovery booted successfully.
Now I need to wait for a replacement battery.
Phone is alive again, thanks tilakpatel for help!
But the magnetic cable trick might be useful in other hardbrick cases: just connect magnetic charger, connect normal USB cable to PC and hold volUp. Phone should be able to enter fastboot even with completely drained battery...
Click to expand...
Click to collapse
no problem

Seriously need help with P8 Lite

I suppose my phone is soft bricked. It doesn't get past the Huawei boot screen. I am still sort of able to enter bootloader and recovery, but I have a problem charging the phone also (which happened after I left in in fastboot mode connected to my PC for a little too long), which means no power to keep it on long for enough to flash rom via fastboot, and trying to do it via 3 key combo with UPDATE.APP on the memory card just says the image is incompatible. The thing with the battery is, when I plug it in it shows that red circle with lightning bolt in the middle like when it's charging, but it immediately changed to green (as if it's fully charged I assume) and the red led flickers. As I understand it, the red light flicking means a battery fault. I know when the red light stays on continuously it means the phone is charging, but that doesn't happen. It just blinks. I can disconnect the battery and retry and it always just keeps blinking, and turning it on means it'll die within 30 seconds. So I can't unbrick my phone if the battery won't charge and furthermore Best of ll is this is I installed a new battery 2 weeks ago and had no problem new battery. I even replaces it AGAIN when I thought the battery was faulty. So perhaps you guys know of some software, hardware, or unconventional trick to get it to charge. I'm very desperate for help! Thanks all for reading!

Just keep it plugged in overnight.

Ugliest Moa said:
I suppose my phone is soft bricked. It doesn't get past the Huawei boot screen. I am still sort of able to enter bootloader and recovery, but I have a problem charging the phone also (which happened after I left in in fastboot mode connected to my PC for a little too long), which means no power to keep it on long for enough to flash rom via fastboot, and trying to do it via 3 key combo with UPDATE.APP on the memory card just says the image is incompatible. The thing with the battery is, when I plug it in it shows that red circle with lightning bolt in the middle like when it's charging, but it immediately changed to green (as if it's fully charged I assume) and the red led flickers. As I understand it, the red light flicking means a battery fault. I know when the red light stays on continuously it means the phone is charging, but that doesn't happen. It just blinks. I can disconnect the battery and retry and it always just keeps blinking, and turning it on means it'll die within 30 seconds. So I can't unbrick my phone if the battery won't charge and furthermore Best of ll is this is I installed a new battery 2 weeks ago and had no problem new battery. I even replaces it AGAIN when I thought the battery was faulty. So perhaps you guys know of some software, hardware, or unconventional trick to get it to charge. I'm very desperate for help! Thanks all for reading!
Click to expand...
Click to collapse
Your battery is drained.. That's the thing.. Charge it, the LED will blink red few times amd as you mentioned, red circle will turn green.. it doesn't mean that the battery is full charged, but instead, it means that the battery is charging... Let the battery charge for few minutes (possibly an hour or so). Do note whether the phone reboots or not.. if not.. its ok..
After charging your device, switch it off (if your device is turned on). Connect it to your PC and just press & hold the vol- key... It should go into fastboot mode... If it goes, then just flash the boot image of your current build..
I too faced similar problem few days back amd resolved it by doing this.. (I was on b596 when I faced this problem, I flashed b596 boot.img)

Ugliest Moa said:
I suppose my phone is soft bricked. It doesn't get past the Huawei boot screen. I am still sort of able to enter bootloader and recovery, but I have a problem charging the phone also (which happened after I left in in fastboot mode connected to my PC for a little too long), which means no power to keep it on long for enough to flash rom via fastboot, and trying to do it via 3 key combo with UPDATE.APP on the memory card just says the image is incompatible. The thing with the battery is, when I plug it in it shows that red circle with lightning bolt in the middle like when it's charging, but it immediately changed to green (as if it's fully charged I assume) and the red led flickers. As I understand it, the red light flicking means a battery fault. I know when the red light stays on continuously it means the phone is charging, but that doesn't happen. It just blinks. I can disconnect the battery and retry and it always just keeps blinking, and turning it on means it'll die within 30 seconds. So I can't unbrick my phone if the battery won't charge and furthermore Best of ll is this is I installed a new battery 2 weeks ago and had no problem new battery. I even replaces it AGAIN when I thought the battery was faulty. So perhaps you guys know of some software, hardware, or unconventional trick to get it to charge. I'm very desperate for help! Thanks all for reading!
Click to expand...
Click to collapse
Did you recently flash anything to the phone

amageek said:
Your battery is drained.. That's the thing.. Charge it, the LED will blink red few times amd as you mentioned, red circle will turn green.. it doesn't mean that the battery is full charged, but instead, it means that the battery is charging... Let the battery charge for few minutes (possibly an hour or so). Do note whether the phone reboots or not.. if not.. its ok..
After charging your device, switch it off (if your device is turned on). Connect it to your PC and just press & hold the vol- key... It should go into fastboot mode... If it goes, then just flash the boot image of your current build..
I too faced similar problem few days back amd resolved it by doing this.. (I was on b596 when I faced this problem, I flashed b596 boot.img)
Click to expand...
Click to collapse
I thought the green circle and red flashing led meant doomsday for my device. I left it overnight at some point and it even got really hot. Strangest thing is, the screen doesn't turn off when it shows the red circle and blinking red led. And having left it overnight like that connected to the charger made the phone very hot and it didn't charge at all.
Roya1jr said:
Did you recently flash anything to the phone
Click to expand...
Click to collapse
I did in fact flash some things, but even after that charging worked just fine! (that was before this charging problem) Just now it doesn't boot. (but I was certain flashboot would rescue me. I know I flashed something I shouldn't have, which is why I'm eager to get back into fastboot, but can't without any power and the PC USB to phone connection doesn't provide enough power for it to stay on.
This oddness started randomly while my phone was connected to my PC in fastboot mode (thankfully before trying to flash anything or running any commands)
I very sincerely hope someone has answers for me. I'm desperate as this was a gift and I just had to tinker. to try a better rom :crying:
But luckily I know this forum has the best experts around!

Is the problem the same as the people in this thread

Open the cell phone and disconnect the battery and reconnect it.
I had the same problem and solved it this way.

Roya1jr said:
Is the problem the same as the people in this thread
Click to expand...
Click to collapse
Yes, I guess it's most likely this way..
---------- Post added at 02:33 AM ---------- Previous post was at 02:30 AM ----------
Ugliest Moa said:
I thought the green circle and red flashing led meant doomsday for my device. I left it overnight at some point and it even got really hot. Strangest thing is, the screen doesn't turn off when it shows the red circle and blinking red led. And having left it overnight like that connected to the charger made the phone very hot and it didn't charge at all.
I did in fact flash some things, but even after that charging worked just fine! (that was before this charging problem) Just now it doesn't boot. (but I was certain flashboot would rescue me. I know I flashed something I shouldn't have, which is why I'm eager to get back into fastboot, but can't without any power and the PC USB to phone connection doesn't provide enough power for it to stay on.
This oddness started randomly while my phone was connected to my PC in fastboot mode (thankfully before trying to flash anything or running any commands)
I very sincerely hope someone has answers for me. I'm desperate as this was a gift and I just had to tinker. to try a better rom :crying:
But luckily I know this forum has the best experts around!
Click to expand...
Click to collapse
Either you open your back case and remove your battery..
Or connect your device to the PC but just by holding your vol- key, that will boot you in fastboot mode.. no matter how little charge you have, it should work

amageek said:
Yes, I guess it's most likely this way..
---------- Post added at 02:33 AM ---------- Previous post was at 02:30 AM ----------
Either you open your back case and remove your battery..
Or connect your device to the PC but just by holding your vol- key, that will boot you in fastboot mode.. no matter how little charge you have, it should work
Click to expand...
Click to collapse
Hey there, thanks for your reply. I have in fact disconnected and reconnected the battery countless times without any effect. I also connected it to PC, disconnected battery, reconnected battery while holding VOL- and it didn't boot into fastboot, just the green circle. Just switching it off with the power button makes it switch on again immediately and holding VOL-still doesn't boot into fastboot mode. I actually once got it to boot into fastboot mode, I can't remember how, but it lasted about a minute then it died from low power even while connected to a US 3.0 port with extra power. y the way, one oddity is that when holding VOL+ is actually goes into recovery mode, but I reflashed stock recovery to try and to flash the UPDATE.APP automatic upgrade, but it didn't work and so it's pretty useless.
Thanks for all the suggestions, you guys are awesome! Really hoping you guys can help me out in the end though!

Ugliest Moa said:
Hey there, thanks for your reply. I have in fact disconnected and reconnected the battery countless times without any effect. I also connected it to PC, disconnected battery, reconnected battery while holding VOL- and it didn't boot into fastboot, just the green circle. Just switching it off with the power button makes it switch on again immediately and holding VOL-still doesn't boot into fastboot mode. I actually once got it to boot into fastboot mode, I can't remember how, but it lasted about a minute then it died from low power even while connected to a US 3.0 port with extra power. y the way, one oddity is that when holding VOL+ is actually goes into recovery mode, but I reflashed stock recovery to try and to flash the UPDATE.APP automatic upgrade, but it didn't work and so it's pretty useless.
Thanks for all the suggestions, you guys are awesome! Really hoping you guys can help me out in the end though!
Click to expand...
Click to collapse
Has it charged since then? When you plug in your cable, does it charge, or does it turn on?
I tried charging with powerbank (at that time, I was out on a bus), it got superhot (the only hot thing I got in my life) and it was turning on automatically... I let it charge for 30 minutes, and then I hold the Power button to shut it down (but it didn't work, I guess).. then I connected it to my laptop just holding the volume- button, it did boot to fastboot..
I am out of suggestions, will post you again if anything else comes to my mind...
Hang in there buddy..

amageek said:
Has it charged since then? When you plug in your cable, does it charge, or does it turn on?
I tried charging with powerbank (at that time, I was out on a bus), it got superhot (the only hot thing I got in my life) and it was turning on automatically... I let it charge for 30 minutes, and then I hold the Power button to shut it down (but it didn't work, I guess).. then I connected it to my laptop just holding the volume- button, it did boot to fastboot..
I am out of suggestions, will post you again if anything else comes to my mind...
Hang in there buddy..
Click to expand...
Click to collapse
Nope, it's not charging. I've used multiple chargers and even different PC's USB connections, but all that comes up onscreen is the round green logo with the battery, and sometimes a red one instead of green.
And of course the constant blinking led, it never goes away. and also the screen doesn't go off like it does when it's charging. I swear the moment it turns solid red, if that ever happens, I shall rejoice.
Nevertheless, I have utmost respect for this site and faith in its member! :good::laugh: I just KNOW someone will help me resolve this. I can enter recovery (stock) but it doesn't charge there not does the silly stock recovery have a option to turn off. And even sometimes when it seems completely drained, it seems like it starts charging after about 2 minutes after I plugged it but it turns on the screen, shows the green circle, and red blinking led. I'm at my wit's end. :crying: It was a gift and I messed it up.

I didn't read everything in this thread, sorry, but just asking, did you try to charge it overnight? My brother had an old, really small Vodafone Huawei Phone and sometimes it just turned off and needed at least 12 hours charging time to turn on again. Maybe just try to let it plugged in for a day. It may help.

Vinnipinni said:
I didn't read everything in this thread, sorry, but just asking, did you try to charge it overnight? My brother had an old, really small Vodafone Huawei Phone and sometimes it just turned off and needed at least 12 hours charging time to turn on again. Maybe just try to let it plugged in for a day. It may help.
Click to expand...
Click to collapse
Yep, I did. Annoying thing is the screen stays on when it's plugged in, unlike charging. I kept it plugged in to a wall charger overnight, and the next morning the phone was hot (supposedly because the screen stayed on) and the led was blinking still. When I unplugged it it lost power. This is so strange because just a week ago there was nothing wrong with the battery even.

Had the same problem couple of times
Try this...
1. unplug battery
2. plug-in charger (without battery!)
3. when charger is plugged to the phone then plug battery connector
Enjoy

groobybca said:
Had the same problem couple of times
Try this...
1. unplug battery
2. plug-in charger (without battery!)
3. when charger is plugged to the phone then plug battery connector
Enjoy
Click to expand...
Click to collapse
I've tried that, multiple times. I don't know what to do anymore, I'm desperate.