Database Develop

Have i permanently bricked my Phone ? Please Help Needed

I just restored my phone to stock rom using rom manager.. After rebooting the phone just keeps on blinking like every two seconds with the LG symbol. Is there any solution to fix this ? Please help..

can you get to "recovery mode" ?
pull out battery, does it still do it when turned on again?
i had this when i used (Rom Manager) to restart my fone into recovery once, it doesnt correctly follow instruction some times.. however manual CWM usually works.

Najmuddin NP said:
I just restored my phone to stock rom using rom manager.. After rebooting the phone just keeps on blinking like every two seconds with the LG symbol. Is there any solution to fix this ? Please help..
Click to expand...
Click to collapse
which ROM you were in before?EXT3 or EXT4?
if you gone back to Stock, u used a smartflash method?did u do the three wipes?switch off the phone, then hold vol down + power key button until you get the second greyish LG logo and then choose wipe data/cache and dalvik (to make a fresh an clean flashing)and reflash the stock ROM...it should be fine then.
hope it helps

from reading the log (as it quickly fly's up the screen) you will see it does this automatically

try nvflash and try to update your recovery.. if your using cwm recovery use 5.0.2

thanks for the help guyz.. its fixed.

Najmuddin NP said:
thanks for the help guyz.. its fixed.
Click to expand...
Click to collapse
For the benefit of everyone. May you share how you fixed your phone?

Please Help!!!!!!!

i just bricked my phone!! i was trying to flash ics chainfire repack with mobile odin. i t then restarted my phone but once it went off the screen where it says "galaxy note gt-7000 i got a blank screen
how do i fix this??
also, what have i done wrong so i dont do it again?
thanks

Press Volume Down + Home + Power for a few seconds and check if it enters download mode ?

Akiainavas said:
Press Volume Down + Home + Power for a few seconds and check if it enters download mode ?
Click to expand...
Click to collapse
thanks for the reply
yes it does enter what i presume to be download mode (up to continue, down to restart)

Boot into download mode and flash a stock rom via Odin then start over your not bricked don't worry

After you do the stock ROM via Odin and let it settle, you can try the ICS repack again. Someone here can help you, but theres already good threads out there for step by step.
One thing I can say since you asked what not to do again is use PC Odin instead of Mobile Odin. Yes, you will get a triangle but you can use triangle away to get rid of it, if you wish. I personally sport the triangle on my phone

Yeah, your phone is not bricked, no worries.
Here's a thread that will help you, make sure to get correct files and flash to stock using PC Odin:
http://forum.xda-developers.com/showthread.php?t=1424997
Thanks to dr. Ketan for his amazing job in gathering it all in one place.

thanks for all the support
as you can tell im abit of a newbie to android (iPhone owner for the last 2 years). if anything happened like this with ios you were basically screwed, so its nice to see thats not the case on android.
also this was the first major thing that had gone with my one week old device so sorry if i over-reacted :/
ps: as im abit of a newbie can anyone point me to a good tutorial for installing ICS rom's?? much appreciated

alex22808 said:
thanks for all the support
as you can tell im abit of a newbie to android (iPhone owner for the last 2 years). if anything happened like this with ios you were basically screwed, so its nice to see thats not the case on android.
also this was the first major thing that had gone with my one week old device so sorry if i over-reacted :/
ps: as im abit of a newbie can anyone point me to a good tutorial for installing ICS rom's?? much appreciated
Click to expand...
Click to collapse
Try long pressing power button and rebooting, if not downloading mode is your way, (do you have ICS rom zip into SD Card?), you will need it to flash it, goes to development threads and you can find it, you can choose one of them, actually I´m on Criskelo V2 LPC6 its good for dayly use its full working, when you got it press at same time Vol +/power button/home and enter in Clockwork mode goes to install zip from sd card, choose from sd card and ICS zip, back to menu wipe data, wipe cache, goes to advanced and wipe dalvick cache, reboot system now and follow steps introducing gmail account and its all enjoy yor NOTE with ICS.

[SOLVED] Help!!! BootLoop and no CWM

Hi Guys
I really hope someone can help me!
I've searched the forums and can't find anyone else with my problem.
I flashed ICS stunner and that was working fine.
Then I tried LiquidSmooth and eventually got that working fine.
Then I tried to go back to ICS Stunner and this is where my problems start.
I had some failed flashes with CWM and I think I've messed up the kernel.
I tried to sort this out by flashing back to pre-rooted GB rom so I could reinstall CF Kernel.
The flash in Odin appears to complete successfully, but afterwards phone just goes into bootloop at Samsung boot animation.
As I flashed back to pre-rooted stock rom I don't have recovery.
As far as I can find, to install a kernel I will need to either boot into android (which I can't due to bootloop) or install through CWM (which I can't as no longer have CWM)
Can anyone help?

Try factory reset from stock recovery.

Boy124 said:
Try factory reset from stock recovery.
Click to expand...
Click to collapse
How do I get into stock recovery?
Edit: Done it and it worked! Thank you sooooo much!
Really thought I'd screwed it! lol!

May be using kies in recovery mode
↖(^▽^)↗ Sent from Galaxy Note ↖(^▽^)↗

How do I get to stock recovery
zX TheRipper Xz said:
Hi Guys
I really hope someone can help me!
I've searched the forums and can't find anyone else with my problem.
I flashed ICS stunner and that was working fine.
Then I tried LiquidSmooth and eventually got that working fine.
Then I tried to go back to ICS Stunner and this is where my problems start.
I had some failed flashes with CWM and I think I've messed up the kernel.
I tried to sort this out by flashing back to pre-rooted GB rom so I could reinstall CF Kernel.
The flash in Odin appears to complete successfully, but afterwards phone just goes into bootloop at Samsung boot animation.
As I flashed back to pre-rooted stock rom I don't have recovery.
As far as I can find, to install a kernel I will need to either boot into android (which I can't due to bootloop) or install through CWM (which I can't as no longer have CWM)
Can anyone help?
Click to expand...
Click to collapse
Hi guys I'm having the same is issue as above
I'm a bit of a noob and still learning
How do I get into stock recovery
Baring in mind im having the same issues as quoted above
Any help would b greatly appreciated
As I'm miserable without my note
Thanks in advance

lalaricon said:
Hi guys I'm having the same is issue as above
I'm a bit of a noob and still learning
How do I get into stock recovery
Baring in mind im having the same issues as quoted above
Any help would b greatly appreciated
As I'm miserable without my note
Thanks in advance
Click to expand...
Click to collapse
Turn off your phone, press and hold the three following buttons together for more than 10 seconds: Volume up button + Home button + Power button
That is if you are having bootloops after flashing Gingerbread using PC Odin coming from ICS

Sorry, I know this post is really old, i have the exact same issue. I dont have a home button so what can i use instead of that? also when it try to boot into recovery it just shows the open android logo.

Mohan211 said:
Sorry, I know this post is really old, i have the exact same issue. I dont have a home button so what can i use instead of that? also when it try to boot into recovery it just shows the open android logo.
Click to expand...
Click to collapse
You do not have the same issue because here nobody spoke of a missing home button.
So: What do you mean? Your home button is broken? Or you do have a device without home button?
After this is clear we can start to analyze your problem.

ThaiDai said:
You do not have the same issue because here nobody spoke of a missing home button.
So: What do you mean? Your home button is broken? Or you do have a device without home button?
After this is clear we can start to analyze your problem.
Click to expand...
Click to collapse
I have a device without a home button so im not sure how to get into recovery without it.

A Samsung Galaxy Note GT-N7000 without a home button? hmmmmm, hmmmmm, hmmmmm. Mohan chachu can you share some Pictures of it please?

Unbelievable. May be you don't know what is home button or your phone is not n7000
Sent from my GT-N7000 using xda premium

Mohin chachoo kya funny ye to yaar
Sent from my GT-N7000 using xda premium

Bricked Note

I have been searching for a solution, but haven't found any..
I flashed to kingdroid rom a while ago from stock GB with abyss kernel. Everything went fine, and later wanted to try a new rom.
So I wiped the data and factory reset in CWM and tried to restore the old stock GB. I don't know if anything went wrong in that process, but now I can't even turn on the phone? I can't boot up CWM either?

fruddy said:
I have been searching for a solution, but haven't found any..
I flashed to kingdroid rom a while ago from stock GB with abyss kernel. Everything went fine, and later wanted to try a new rom.
So I wiped the data and factory reset in CWM and tried to restore the old stock GB. I don't know if anything went wrong in that process, but now I can't even turn on the phone? I can't boot up CWM either?
Click to expand...
Click to collapse
Can you enter download mode??If so flash any GB rom.If the flash is getting stuck at factoryfs or somewhere for long than 15 mins..you have superbricked your phone by doing a wipe.Only way is to replace the mobo or trying this

yeah go on download mode. Use odin pc. It will raise the counter, but its much better than a brick note.. Hehe

Download mode is volume down, home key and turn on key right?
Doesnt work.. how long is I supposed to hold it in?
And what is a MOBO?

Easy ... Don't Panic
fruddy said:
I have been searching for a solution, but haven't found any..
I flashed to kingdroid rom a while ago from stock GB with abyss kernel. Everything went fine, and later wanted to try a new rom.
So I wiped the data and factory reset in CWM and tried to restore the old stock GB. I don't know if anything went wrong in that process, but now I can't even turn on the phone? I can't boot up CWM either?
Click to expand...
Click to collapse
The First Thing you did was right, since you did the wipe using the AbyssKernel kernel, witch was safe and away from the HardBrick Thing around the Stock ICS Kernel.
But what you did wrong, is that you did wipe and restore using the Kernel inside the rom you used, wich of course was in cause !!!! so Here is what you will do, just Follow the Steps in My following Post, and you are done
http://forum.xda-developers.com/showpost.php?p=26772618&postcount=12
IF this Helped, Then you Know what to do

Glad to hear kimifender!
Sorry for not being that bright in all this.. But how can I do all the instructions when I can't turn the phone on? I can't find the sdcards on my computer either when i connect the phone to the computer

Sounds like you have a big paperweight. You need to somehow get it to a Samsung repair center to get the motherboard replaced. There's a thread in the General section that MIGHT help revive it, but no guarantees.
Always make sure you read, read, read before you flash anything. Like other people said, the restore is what bricked it.

kimifender said:
The First Thing you did was right, since you did the wipe using the AbyssKernel kernel, witch was safe and away from the HardBrick Thing around the Stock ICS Kernel.
But what you did wrong, is that you did wipe and restore using the Kernel inside the rom you used, wich of course was in cause !!!! so Here is what you will do, just Follow the Steps in My following Post, and you are done
http://forum.xda-developers.com/showpost.php?p=26772618&postcount=12
IF this Helped, Then you Know what to do
Click to expand...
Click to collapse
He said he wiped after beeing on the other rom. So he wiped with an unsafe kernel.
=> Superbrick.

So there is no way I can revive my phone?
Maybe im just not turning it on the right way?

fruddy said:
So there is no way I can revive my phone?
Maybe im just not turning it on the right way?
Click to expand...
Click to collapse
If you're pushing the power button, you are turning it on. If you are holding down volume up/down + power + home button you are trying to put it in download/recovery.
Sorry, but it sounds like it is a paperweight/brick.

fruddy said:
So there is no way I can revive my phone?
Maybe im just not turning it on the right way?
Click to expand...
Click to collapse
Check battery. make sure it still has power. Pull out and leave out 5 minutes and replace it back as well.
Then turn it on and try to enter download mode (Home volume-down and power) and connect it to PC odin (even in case the screen does not turn on) and see the yellow box is there. If there is, you can flash kernel that has CWM as well, and there is hope to revive it.
If you cannot get odin to see it, then SS service is the only way.

fruddy said:
So there is no way I can revive my phone?
Maybe im just not turning it on the right way?
Click to expand...
Click to collapse
Well Of course, If your phone is not ON, it won't show any usb storage on the PC.
Don't Give up Yet !!!
Are you sure your phone has enough battery charge,
Not Sure? well Do this :
- Keep your phone under AC Battery Charger (no USB charging) for at least 45 min.
- Take Off the Battery for at least 10s seconde,
put it back, Then try to to enter to download mode directly : Vol down + Power + Home Button at the same time untill you see the Yellow Dowload Logo, Don't Try to turn your phone on by Pressing the power Button as Normally, It Simply won't turn on !!
Keep taking the Battery Off and Back untill it works, believe me this happened before.

How much would it cost to get it fixed?
How much would a new motherboard cost?

fruddy said:
How much would it cost to get it fixed?
How much would a new motherboard cost?
Click to expand...
Click to collapse
Try My Post First untill it works, Believe it or not !!!!!

I really doubt that will work if he has a superbrick. If it does it would be amazing.

But how can i flash, when I can't even turn on the phone?

fruddy said:
But how can i flash, when I can't even turn on the phone?
Click to expand...
Click to collapse
Try what I told you in Post N°12,
If you get the chance to get into the download mode : then Follow My Post N°5.
You Have to Make sure your phone is really Dead, or just need a push to wake up again.
I swear this happened to me before, and believe me I'm no noob.
Just Try First. If it doesn't work, then Buy another one ;;;;

how i fixed it
Iám new as a member here but not new on reading here on this forum.
Want to post fast how i brickt my phone with ics and kernel problems and wipe going wrong.
Cwm still working but nothing is going anymore.
In cwm flash a franco kernel (i used Franco kernel 10 because had it on my sd card) then reboot into recovery and flash the Abys kernel.
Reboot into recovery and install your rom or restore an backup you made.
I hope sthis works for all.

annoniem said:
Iám new as a member here but not new on reading here on this forum.
Want to post fast how i brickt my phone with ics and kernel problems and wipe going wrong.
Cwm still working but nothing is going anymore.
In cwm flash a franco kernel (i used Franco kernel 10 because had it on my sd card) then reboot into recovery and flash the Abys kernel.
Reboot into recovery and install your rom or restore an backup you made.
I hope sthis works for all.
Click to expand...
Click to collapse
Reaaaaaaad,
He can not wake his phone up, or turn it on !!!
So How would he install any Franco or what ever ...... !!!!!!!!

bricked Note
kimifender said:
Reaaaaaaad,
He can not wake his phone up, or turn it on !!!
So How would he install any Franco or what ever ...... !!!!!!!!
Click to expand...
Click to collapse
You tell him lol, i love how he wrote "Im new as a member here but not new on reading here on this forum"

Help please with flashing Rom (potentially bricked?)

Hi,
I was running the JellyBam installer having rooted using a guide at cursed4eva, using cwm.zip. The only thing I'm unsure of is because the phone was owned before me, whether a custom kernel was installed (perhaps Franco as it was on the sd card)... I wiped everything using recovery mode, and ran cwm.zip, then followed the guide. Everything was going fine, until during the installer it asked if I want to update a kernel or keep the kernel thats already on, but not knowing what to do and not being able to find anything on the internet, I just left it at the default option and updated the kernel. It remained on 2% while uncompressing the image file, but when I looked my phone had turned off and was unresponsive. I was going from rooted stock 4.04. Both recovery mode and download mode aren't available...
Is it likely to be hard-bricked or softbricked, and what do you suggest doing? I haven't had it over a year, so under UK law I should still have warranty on it, right?
Please help!
Warm regards,
Lee

Sounds more like a superbrick.. It's wells known that cwm.zip adviced by cursed4eva in YouTube its dangerous and can trigger the emmc bug.. I don't know why that dude haven't remove that video so far..
Try removing the battery for some minutes and then turn on the device in odin mode (power +volume down +home) and flash a stock gingerbread with pc odin
Tapatalking on my n7000

msedek said:
Sounds more like a superbrick.. It's wells known that cwm.zip adviced by cursed4eva in YouTube its dangerous and can trigger the emmc bug.. I don't know why that dude haven't remove that video so far..
Try removing the battery for some minutes and then turn on the device in odin mode (power +volume down +home) and flash a stock gingerbread with pc odin
Tapatalking on my n7000
Click to expand...
Click to collapse
Thanks for your quick and helpful response. I'll try it in the next few hours, and let you know how it goes. Is the superbrick fix the thing which, if successful loses 3gb of space?
Once again, thanks for your help

angus_mcfisher said:
Thanks for your quick and helpful response. I'll try it in the next few hours, and let you know how it goes. Is the superbrick fix the thing which, if successful loses 3gb of space?
Once again, thanks for your help
Click to expand...
Click to collapse
Yes that's the one.

angus_mcfisher said:
Thanks for your quick and helpful response. I'll try it in the next few hours, and let you know how it goes. Is the superbrick fix the thing which, if successful loses 3gb of space?
Once again, thanks for your help
Click to expand...
Click to collapse
First what it's first.. Flash the stock gb.. If that doesn't work then following question would be do you have warranty?
Tapatalking on my n7000

msedek said:
First what it's first.. Flash the stock gb.. If that doesn't work then following question would be do you have warranty?
Tapatalking on my n7000
Click to expand...
Click to collapse
I haven't been able to access a PC tonight, but I'll try tomorrow. I don't suppose it's possible on a Mac is it? It is within my 1 year statutory rights, so that should be ok
Thanks for all your help guys!

If nothing happens when I've connected it to the PC with Odin open, and pressing Power+Vol Dwn+Home, does that mean its super bricked, or am I just doing something wrong?

angus_mcfisher said:
If nothing happens when I've connected it to the PC with Odin open, and pressing Power+Vol Dwn+Home, does that mean its super bricked, or am I just doing something wrong?
Click to expand...
Click to collapse
You need to put the device in odin mode (volume down + home + Power until a warning shows up) when the warning appear on the screen release everything and press volume up to confirm.. Once in odin mode you can plug the device to the pc.
But before that you need to install either kies or samsung drivers in your pc.. You can find samsung drivers in Dr ketans toolbox in general section.. Once done with this, connect the device and wait for Windows to setup the device..
Once donde you can open odin.. And a yellow block should turn on In the upper left corner..
Tapatalking on my n7000

msedek said:
You need to put the device in odin mode (volume down + home + Power until a warning shows up) when the warning appear on the screen release everything and press volume up to confirm.. Once in odin mode you can plug the device to the pc.
But before that you need to install either kies or samsung drivers in your pc.. You can find samsung drivers in Dr ketans toolbox in general section.. Once done with this, connect the device and wait for Windows to setup the device..
Once donde you can open odin.. And a yellow block should turn on In the upper left corner..
Tapatalking on my n7000
Click to expand...
Click to collapse
Thanks for your quick reply. I tried putting my device into Odin mode, but nothing appeared on the screen (and I held it for about a minute!). I've downloaded the Samsung Drivers, just to double check that it was already installed, and it was.
I can't get anything whatsoever on the screen. I don't even know if it's working at all... I can't get anything even though it's plugged into the mains. Any help would be greatly appreciated

First of all try to charge the battery externally using other phone or a ext charger. make sure there is juice on the battery and try to go to download mode again. battery might not get charged in that phone...
Once that done and still the phone is unresponsive .., no indication of screen display at all.like the N7000 logo (vol dwn+pwr+home) or (vol up+power+home), then it may be hard bricked and need a motherboard replacement .. I guess the samsung warranty is from the date of purchase as on the cash memo

Many thanks. I've had it plugged in and I can feel its warm so it must be charging. I've also tried a replacement battery to no avail. I guess it must be completely bricked. If Samsung only replace the motherboard then I'll try the retailer first, worth a try!
Many thanks for your help

Ok.. and let us know how it goes

nokiamodeln91 said:
Ok.. and let us know how it goes
Click to expand...
Click to collapse
Have to love Amazon! Even though I bought it last May, they're replacing it - no questions asked! Is there a guide on how to do this the best way possible on the new device? There's so much out of date information on the internet, including the guide I initially followed!

angus_mcfisher said:
Have to love Amazon! Even though I bought it last May, they're replacing it - no questions asked! Is there a guide on how to do this the best way possible on the new device? There's so much out of date information on the internet, including the guide I initially followed!
Click to expand...
Click to collapse
Dead its dead... Just return it and please do not ever wipe on ics stock kernels or use cwm.zip just read here or ask... Better ask than burning another device
Tapatalking on my n7000

Well lesson learned my friend and also for everyone else that reads this including myself. Happy to see you are getting it replaced l!
->] [ALLIANCE] [ICS] [FINAL] [<-

angus_mcfisher said:
Is it likely to be hard-bricked or softbricked, and what do you suggest doing? I haven't had it over a year, so under UK law I should still have warranty on it, right?
Please help!
Warm regards,
Lee
Click to expand...
Click to collapse
Hope this will help,
http://forum.xda-developers.com/showthread.php?t=1656635

amjiffy70 said:
Hope this will help,
http://forum.xda-developers.com/showthread.php?t=1656635
Click to expand...
Click to collapse
Hes already getting a replacement

Thanks guys. Yeah, I got a replacement today from Amazon. No questions asked! Just to clarify to install Jellybam, I can follow the steps on http://forum.xda-developers.com/showthread.php?t=1901191 to replace the kernel, and then going into Recovery Mode, flash the zip and then during the installer I don't want to replace the kernel? Right?

angus_mcfisher said:
Thanks guys. Yeah, I got a replacement today from Amazon. No questions asked! Just to clarify to install Jellybam, I can follow the steps on http://forum.xda-developers.com/showthread.php?t=1901191 to replace the kernel, and then going into Recovery Mode, flash the zip and then during the installer I don't want to replace the kernel? Right?
Click to expand...
Click to collapse
Philz kernel is only for stock samsung roms. If the new phone you go is on stock ICS rom, then install this kernel from stock recovery. This will give you root.
The boot into recovery and do all wipes ( factory reset and wipe cache partition dalvik cache)
then go to mounts & storage and do format /system, format/data, format/preload.
then go to Install Zip and install the rom
This rom wont work with Philz kernel. so you need to use the kernel included in the ROM or Hydracore V7.

nokiamodeln91 said:
Philz kernel is only for stock samsung roms. If the new phone you go is on stock ICS rom, then install this kernel from stock recovery. This will give you root.
The boot into recovery and do all wipes ( factory reset and wipe cache partition dalvik cache)
then go to mounts & storage and do format /system, format/data, format/preload.
then go to Install Zip and install the rom
This rom wont work with Philz kernel. so you need to use the kernel included in the ROM or Hydracore V7.
Click to expand...
Click to collapse
Ok thank you for your help! I'll start now and let you know how it goes. Is there anything in this process that I need to be careful to ensure I don't brick it (other than using cwm.zip!)?