Hi!
This is my first post an I hope I did put it on the right place and I havent found any other post that really matches my problem.
Anyway, I was so happy for being able to bring back stock rom on a rooted SGS2 I9100 who didnt worked proper with its root. In this case, no USB-debugging were necessary.
After this mission I felt ready to try to downgrade the SGS Advance I9070 from stock Jelly Bean to Stock Ginger Bread by mainly following one of all those tutorials about how to do it. And I know its said - enable USB-debugging.
But as I were interupted by my wife just before I were going to proceed, I totally forgot it when I finally went back to my work of downgrading. As I were a bit stressed, I just connected the phone to Odin and slammed the PDA-button like I did with the SGS2. It went smooth all the way through Odin and the green PASS showed up. But when the phone were about to boot up it stuck at the Samsung-logo. Its in a bootloop. After a short time of wondering about what went wrong, it struck my head I forgot to enable USB-debugging. Amen!
So, I forgot debugging while running JB-stock to downgrade to GB-stock. The only thing I can reach now is download-mode except the bootloop Samsung start interface. Its probably occured because I forgot enable debugging, right? And does it mean this device is bricked for real or is there anyway to bring back life?
Best regards // emsoh
emsoh said:
Hi!
This is my first post an I hope I did put it on the right place and I havent found any other post that really matches my problem.
Anyway, I was so happy for being able to bring back stock rom on a rooted SGS2 I9100 who didnt worked proper with its root. In this case, no USB-debugging were necessary.
After this mission I felt ready to try to downgrade the SGS Advance I9070 from stock Jelly Bean to Stock Ginger Bread by mainly following one of all those tutorials about how to do it. And I know its said - enable USB-debugging.
But as I were interupted by my wife just before I were going to proceed, I totally forgot it when I finally went back to my work of downgrading. As I were a bit stressed, I just connected the phone to Odin and slammed the PDA-button like I did with the SGS2. It went smooth all the way through Odin and the green PASS showed up. But when the phone were about to boot up it stuck at the Samsung-logo. Its in a bootloop. After a short time of wondering about what went wrong, it struck my head I forgot to enable USB-debugging. Amen!
So, I forgot debugging while running JB-stock to downgrade to GB-stock. The only thing I can reach now is download-mode except the bootloop Samsung start interface. Its probably occured because I forgot enable debugging, right? And does it mean this device is bricked for real or is there anyway to bring back life?
Best regards // emsoh
Click to expand...
Click to collapse
LOL...:laugh: Wives will remain Wives!
The device is Soft Bricked and can be resurrected..did you follow this procedure: http://forum.xda-developers.com/showthread.php?t=2195673 ?
arneldna said:
LOL...:laugh: Wives will remain Wives!
The device is Soft Bricked and can be resurrected..did you follow this procedure: http://forum.xda-developers.com/showthread.php?t=2195673 ?
Click to expand...
Click to collapse
Haha.. Well, I had to drive her to the shop and that was enough to make me lose my patience of remembering important rules just because I had to go with other important rules. Like the gentleman I am. :fingers-crossed:
Thanx for reply. It makes me glad you do believe its possible to fix this issue. The link you showed is on of those I been looking at before I got started. But after a lot of comparing between several links from i-net, I decided to go with the procedure that the majority declared. For example, in this link its said "re-partition" must be ticked in. The other guides said not. Only "reboot" and "time-reset" to be ticked in.
The stock firmwire I downloaded were from some address connected to Samsung. It means there were only one file with all included just to insert in the PDA. Now, afterwards..I do understand it isent that hard to fill in 3 lines myself instead of one. But it seemed simplier with only one at that time. As I am a newbie about changing software in phones, I were ready to make mistakes but not this mistake and I really dont know what guides who are the best to go with.
Do you think it will make any difference if I go with your link and try again?
Remember, the phone were not rooted. Im really not sure, but I think I read somewhere that if debugging are not enabled on official kernel, theres no way back because cant reach debugging in any way. But I hope its not true.
Now, as far as I understand in my case...what I did was to erase the operation system I had (stock 4.1.2) and filled it up with (stock 2.3.6) but it only reached the gates and not the internal of the phone. It means there are no operating system at all?
Then why Odin shows PASS? And if no communication files can reach the phone, how is it possible that the counter now shows the phone has been rooted? Yes, I tried to root it today and Odin showed PASS again. And as the counter counts, it must mean the phone is not 100% blocked from communication even without debugging enabled?
But still the phone act as described earlier. Only Samsung-logo, bootloop and I can only go forward to download-mode.
:crying:
emsoh said:
Haha.. Well, I had to drive her to the shop and that was enough to make me lose my patience of remembering important rules just because I had to go with other important rules. Like the gentleman I am. :fingers-crossed:
Thanx for reply. It makes me glad you do believe its possible to fix this issue. The link you showed is on of those I been looking at before I got started. But after a lot of comparing between several links from i-net, I decided to go with the procedure that the majority declared. For example, in this link its said "re-partition" must be ticked in. The other guides said not. Only "reboot" and "time-reset" to be ticked in.
The stock firmwire I downloaded were from some address connected to Samsung. It means there were only one file with all included just to insert in the PDA. Now, afterwards..I do understand it isent that hard to fill in 3 lines myself instead of one. But it seemed simplier with only one at that time. As I am a newbie about changing software in phones, I were ready to make mistakes but not this mistake and I really dont know what guides who are the best to go with.
Do you think it will make any difference if I go with your link and try again?
Remember, the phone were not rooted. Im really not sure, but I think I read somewhere that if debugging are not enabled on official kernel, theres no way back because cant reach debugging in any way. But I hope its not true.
Now, as far as I understand in my case...what I did was to erase the operation system I had (stock 4.1.2) and filled it up with (stock 2.3.6) but it only reached the gates and not the internal of the phone. It means there are no operating system at all?
Then why Odin shows PASS? And if no communication files can reach the phone, how is it possible that the counter now shows the phone has been rooted? Yes, I tried to root it today and Odin showed PASS again. And as the counter counts, it must mean the phone is not 100% blocked from communication even without debugging enabled?
But still the phone act as described earlier. Only Samsung-logo, bootloop and I can only go forward to download-mode.
:crying:
Click to expand...
Click to collapse
Don't worry - as long as you have access to download mode you are fine :good:
I am not sure as I never downgraded to GB myself, but from my understanding of posts in here it is partitioning issue.
JB got different sizes or mount points (forgot exactly) of key partitions and that is what is wrong here - it cannot find some components to finish booting.
re-partition is the main thing here.
Get file from this guide.
Key point is:
9)Hit on PIT button and select the PIT file extracted from the downloaded package in first step above (GT-I9070_EUR_XX_8G.pit).
You should be able to use your 1-file-ROM and get it working, as long as you use .pit and tick re-partition.
Worst case scenario - flash JB again (no re-partition needed) and it will be working as before ;]
th3cr0w said:
Don't worry - as long as you have access to download mode you are fine :good:
I am not sure as I never downgraded to GB myself, but from my understanding of posts in here it is partitioning issue.
JB got different sizes or mount points (forgot exactly) of key partitions and that is what is wrong here - it cannot find some components to finish booting.
re-partition is the main thing here.
Get file from this guide.
Key point is:
9)Hit on PIT button and select the PIT file extracted from the downloaded package in first step above (GT-I9070_EUR_XX_8G.pit).
You should be able to use your 1-file-ROM and get it working, as long as you use .pit and tick re-partition.
Worst case scenario - flash JB again (no re-partition needed) and it will be working as before ;]
Click to expand...
Click to collapse
Ok, it makes me a bit more calm and Im starting to believe a bit, theres a way back for the phone to rise again. So you mean it might not be the failure of missed debugging, instead the critical main thing can be re-partiton?! It sounds very possible based on what you said.
The thing now is, ofcourse I would be satisfied if my first plan come true. But right now I really dont care what version it´ll be running, rooted or not. I only want it to act like a smartphone again n matter what´s installed. So I will go with your advise and test it one by one.
Thanx so far! To be continued..
SOLVED Forgot USB-debugging downgrading
I must admit I didnt really believed it wud work even I hoped it wud do. Before I started the new operation I gave it the chances 75% negative and 25% positive. But I was so wrong.
It really passed!!
Im so thankful for the support. To arneldna who made me reconsider this current version and tutorial for firmware downgrade. And to th3cr0w who explained and really pointed out the missing spot in my failure of action during the installing process.
The solution - Just to be sure, I followed the tutorial exactly. When it rebooted it showed up not to be my country region so I did it again with my nordic region all-in-one tar-file. This time just to be safe, I enabled usb-debugging and also unknown sources. Idk if it had any use but just in case of. And Voila..back to my region and everything seems to be as it was the first time I started up the phone when it was new last summer. After that I did a factory reset which I learned is useful to do.
As this was only one of my childrens phones, I actually got 3 more of the same to downgrade to work smooth again. But now I learned another lesson. I hope!
THANX A LOT to both of you! :good:
emsoh said:
I must admit I didnt really believed it wud work even I hoped it wud do. Before I started the new operation I gave it the chances 75% negative and 25% positive. But I was so wrong.
It really passed!!
Im so thankful for the support. To arneldna who made me reconsider this current version and tutorial for firmware downgrade. And to th3cr0w who explained and really pointed out the missing spot in my failure of action during the installing process.
The solution - Just to be sure, I followed the tutorial exactly. When it rebooted it showed up not to be my country region so I did it again with my nordic region all-in-one tar-file. This time just to be safe, I enabled usb-debugging and also unknown sources. Idk if it had any use but just in case of. And Voila..back to my region and everything seems to be as it was the first time I started up the phone when it was new last summer. After that I did a factory reset which I learned is useful to do.
As this was only one of my childrens phones, I actually got 3 more of the same to downgrade to work smooth again. But now I learned another lesson. I hope!
THANX A LOT to both of you! :good:
Click to expand...
Click to collapse
Glad to know you fixed it.. Appreciate your patience and efforts... :thumbup:
You don't care where I sent it from....!
Related
Hello
I hope i have posted in the right section and someone can explain too me if this is right or wrong.
I just downloaded the 2.0 version of samsung kies software,when i plugged my phone in it said i could do a firmware upgrade for my phone.
So of course i did so,i first done the backup which was an option in the process.Then pressed ok and it started doing its thing.
Well i left it and came back too see a green android guy on the phone and a message on laptop saying the update had failed and i need too recover the fail by going into emergency firmware recovery mode.
I did this(pressed yes) and it started doing its thing again and rebooted the phone,after it had done it said too disconnect and reconnect my usb cable which i did and the phone was back running again.
The question i have is what basically just happened?
I presume it was a fail on the firmware update since thats what it told me but on checking my stats it had done what it said it was going too and thats upgrade from CSC: JP5 to CSC: JP6.
So it said it failed but on the samsung kies software it now says the csc JP6 and i cant update any firther.
Im sorry i should maybe of checked the code better too be honest i didnt check the full version upgrade, i just thought ok firmware upgrade yup ill do that and flicked through the yes options til the upgrade started.
Thanks for any replies.I have a untouched samsung galaxy S by the way,i not done anything too it except installed apps and games.So no roms,no lag fix,no hacks at all.
Its been a coupleof days now since my post so hope its ok too comment in it again so maybe i can get some help.
Im not sure if my first post explained itself enough so if anyone has any questions i will be happy too answer them.I dont know if my phone will be affected long term but the fail or not.
Csc..what is this why had the software felt it needed too be changed from 5 to 6 ?
the fact it said it failed yet on checking i cannot update again and it has in fact changed from 5 to 6 as it said it would.All my added shortcuts on home screens went but the files stayed.
csc....has anyone also got the changed firmware like i have and gone through the failure too get it.
Im trying too add my own questions in the hope someone has some answers since i see many questions get answered in this section within no time,but mine seems too of stumped some.
thanks for replies guys it will settle my mind and i will of course try too find my own answers and if all else fails i will contact samsung and ask them what went wrong.
Hi,
I installed Kies today and connected my girlfriends cellphone, a Samsung Champ Duos (don't know if it's a phone only for the Philippino market)... Same here, started up first time and Kies prompted me to update the phone's firmware. I followed the steps, something went wrong and I was told to perform an emergency recovery.
I tried, but after 63% an error message appear telling me that something went wrong and "if the problem persists please contact support centre".
I've tried the recovery process maybe 20 times now and same every time. I have already sent an email to the support, but hoping someone here knows how to fix this in the meantime.
Thanks in advance!
Not sure Kies can be unreliable...
Have you tried another computer?
Try the recovery again but hold the usb cable in place, it may have a loose connection
Either way support should answer you shortly and they will sort it out, as it should be under warranty and kies messed it up. They will probably tell you to find your nearest service centre...
@Caz2k11 if you ever read this again and still haven't got your answer, it shouldn't have affected you that there was a problem installing in the first place.
CSC - there is a sticky on the the general section that describes most of this stuff but in brief i think its either country specific code or country service code, something like that. Really its only important if you have problems downloading things from the market, or reception/data related issues. Usually carrier related... Its worth checking you have the correct one when you update as it saves you from changing it later which results in a factory reset.
Ahh damn it...
Got a reply from their support this morning. They apologized and told me I have to send the phone to my nearest service centre. Great for me living in the province and I'll bet the closest service centre is located in Manila....
Does anyone know if the *original rom* is available somewhere on the internet?
Most of us do not use kies to update
You can fiind the latest original ROMs at samfirmware.com
jc
3d_jc said:
Most of us do not use kies to update
You can fiind the latest ROM ar samfirmware.com
jc
Click to expand...
Click to collapse
Hehe no ****
I'm running Andriod on my HTC Leo as well, but this is my girlsfriends phone, still warranty so I'll be a bit careful at the moment.
Have registered on the site mentioned above, not sure which file I'm going to use or anything, since I cannot start the phone to see the current firmware etc. The model no. is GT-E2652W and "SSN" is "E2652WGSMH", does that mean it's a E-series phone?
It means a few things ...
First of all, you are totaly at the wrong place since this forum section is for Samsung Galaxy S, and you Champ Duo , well, isn't a Galaxy S !
Second thing is that this forum, as well as samfirmware, deal mostly with Android phones, which your isn't, I believe. It does somehow look like, but isn't.
Sorry I can't help more
jc
3d_jc said:
It means a few things ...
First of all, you are totaly at the wrong place since this forum section is for Samsung Galaxy S, and you Champ Duo , well, isn't a Galaxy S !
Second thing is that this forum, as well as samfirmware, deal mostly with Android phones, which your isn't, I believe. It does somehow look like, but isn't.
Sorry I can't help more
jc
Click to expand...
Click to collapse
Yes, I'm awared of that. Found this thread when I Google-searched "samsung emergency recovery".
Sure, no arm done, it's just that non android phone have a different way to recover. I did a couple of googling too, but must admit I did not find a great deal of information either,
Sorry and best of luck for bringing your device back to happiness.
jc
I have done hours of researching and this isn't my first time i bricked a phone so I kind off have some experince fixing the phone but this seems harder than before.
I first tired to flash a kernel through odin on my captivate because i wanted to try out cyanogen mod but somehow the kernel had failed on me. When i tried to restart my phone, I got the phone---!---pc logo.
So i did some research on how to get the phone out of the soft brick. First thing I did was trying to get into recovery mode with the 3 buttons, but didnt work out. After that I tried to get into download mode and it worked. My first thought was too use odin and reflash, and that is what i did. Now the problem is, I had put the correct pit file and stock rom, because I had reflashed using these two same files before, but the thing is, it gets stuck on "set partition". So I did everything from, trying on different computers to changing usb cables to using different versions of odin and finally to taking out the sim card and sd card and taking out and placing the phones battery back in. And i had everything checked too so that wasn't the problem. The following were checked: Auto Reboot, Check Re-Partition and F.Reset Time.
If anyone knows the solution can you please help me out, thank you in advance!
When you check repartition, you need to load a pit file in the pit slot/tab for Odin. You have two options.
1) Flash froyo stock(kb2), if you don't want/need Gingerbread Bootloaders. The Heimdall package from Adam Outler is an easy 1 click solution.
2) Flash KF1 if you need GB bootloaders. This will also fix ant previous 3 button combo problem you may have. Use the package with a pit file and bootloaders.
It also sounds like you may need ajig to get into download mode, but if you follow the Captivate sig link below, you should be able to find everything you need to get going.
Thank you !
Thanks a lot mrhaley30705 ! I have gone through of some guides and done more research about these two, and I was thinking of flashing kb2 on to my phone but I'm really worried if it might brick my phone, because the captivate I have is the rogers one not the ATT&T one.
I just had a few questions like, before I do the Heimdall One-Click, is it required to install the Zadig file ? because it had came up before I opened up the Heimdall One Click program. I think i had used the Heimdall One-Click before (the video that is posted on youtube) by outleradam, but the thing was, it wasn't recognizing my phone. So I'm guessing it has something to do with Zadig file, because I made sure I ran it as Administrator also so I'm kinda lost.
My other question was, the consequences, if this program would not work for me, would it hard brick my phone? I really want to make sure I go ahead with it.
And my last question is, if I were to go ahead with this, it said on the forum I would have to reset my APN settings, so would that be applying another software to the phone or can i configure that manual ?
And Thanks again for all your help !
If you want the Canadian firmware, search for TRusselo's stock threads. He has a full set of Canadian firmware.
Anytime you flash bootloaders there is a chance of hard bricking your phone, either from an interruption in communication between your phone and computer (think power outage or bad cable) or accidentally mismatching bootloaders (think the old 3 button fix on top of GB bootloaders). Just follow all of the precautions you can when flashing bootloaders.
APN editing is done manually.
Oh alright I got how put the APN information, thank you.
And oh okay, that makes more senses.
And for the Canadian firmwares, that's what I pretty much did with Odin, I took his stock firmware and tried to flash it with Odin but wasn't passing the "set partition" part like I mentioned before. I followed his instructions too. So, that's why I'm a bit confused now, because I'm guessing if Odin doesn't work then I would have to use the Kb2 link that is posted on your Sig. Do you have any suggestions maybe ?
The canadian version of the captivate will flash the US verson, it just changes your boot screen and kernel splash to an att one. I would flash the KB2, then if you absolutley had to have the canadian version, flash it.
Thank you !
Thanks a lot once again ! and I will give it a try and let you know how it goes !
Maybe try NOT checking re-partition. This sometimes can cause a problem, in fact most tutorials i have seen always say DO NOT check re-partition. It's worth a try
Hello there,
I just bought a galaxy note <well a week ago> and now i ended up soft bricking it.
here's how i did it -
I went to my friends place thinking of rooting my phone while he told me to add a custom rom to it . well since he was experienced i let him do it . he added a firmware of i9200(chinese ). well it worked now i found some chinese system applications that i didn't need and while searching on net how to do it i found a firmware of n7000 ics online and decided to flash it in. since i was at home i thought i would be able to do it myself and did what i shouldn't have done. i followed every step they said online and started the downloading of the rom but unfortunately when pc odin was at it's end i mean the end of downloading i actually disconnected the cable ( what the f*** was i thinking) . now i tried to reinstall the same rom but couldn't - pc odin always showed setting up connection or something like this and then stalled for hours ... i thought of flashing some other rom but it didn't - same thing <stalling for hours> . Now what should i do??? help me - maybe i can go to samsung customer care service and ask them to reset my phone but since the usb debugging was on last time when i turned my phone off , kies might not do the job . can u suggest me a way.
one more thing i can't flash stock rom into it and <i am dumb> i didn't backed up my stock rom.
p.s. my flash count is 2 . i can't load my phone into recovery mode but can into download mode and can't do it with a jig (am from india plus i am a little low on technical know how).
i can't hard reset it either. a suitable help would be appreciated ,pls
kunalteji1993 said:
Hello there,
I just bought a galaxy note <well a week ago> and now i ended up soft bricking it.
here's how i did it -
I went to my friends place thinking of rooting my phone while he told me to add a custom rom to it . well since he was experienced i let him do it . he added a firmware of i9200(chinese ). well it worked now i found some chinese system applications that i didn't need and while searching on net how to do it i found a firmware of n7000 ics online and decided to flash it in. since i was at home i thought i would be able to do it myself and did what i shouldn't have done. i followed every step they said online and started the downloading of the rom but unfortunately when pc odin was at it's end i mean the end of downloading i actually disconnected the cable ( what the f*** was i thinking) . now i tried to reinstall the same rom but couldn't - pc odin always showed setting up connection or something like this and then stalled for hours ... i thought of flashing some other rom but it didn't - same thing <stalling for hours> . Now what should i do??? help me - maybe i can go to samsung customer care service and ask them to reset my phone but since the usb debugging was on last time when i turned my phone off , kies might not do the job . can u suggest me a way.
one more thing i can't flash stock rom into it and <i am dumb> i didn't backed up my stock rom.
p.s. my flash count is 2 . i can't load my phone into recovery mode but can into download mode and can't do it with a jig (am from india plus i am a little low on technical know how).
i can't hard reset it either. a suitable help would be appreciated ,pls
Click to expand...
Click to collapse
I have no experience with this, but I did keep this video link on how to put a bricked Samsung into download mode just in case I needed it. The usb jig is the same for both the captivate and the Note from what I have read:
http://androidforums.com/captivate-...ung-captivate-usb-jig-video-start-finish.html
If you are able to enter download mode then Just try with different version of PC Odin , like V1.83, V1.85, V1.87. and do not worry about Stock ROM you can always download it from below link.
http://forum.xda-developers.com/showthread.php?t=1329360
thankyou guys but i can't use jig since i can't buy it nor am i capable of making one.
Rajan , bro my problem is something different. the roms i am trying to insert in my phone was via the odin i used earlier to flash my first rom. and it went successfully . but last time the second rom i inserted was interrupted during download and am not able to add anymore of them. now i have talked to samsung care and they told me to bring my phone along with the bill maybe they can do it. even though my warranty is done for, but i think i can believe them . yet if there are any other suggestions pls tell me or should i give it to samsung care. I really don't wanna keep my phone rooted so i have no problem flashing stock but it's not happening. CAN KIES HELP?
p.s i have used all 1.85 , 1.87 and 1.83 version no use.
kunalteji1993 said:
thankyou guys but i can't use jig since i can't buy it nor am i capable of making one.
Rajan , bro my problem is something different. the roms i am trying to insert in my phone was via the odin i used earlier to flash my first rom. and it went successfully . but last time the second rom i inserted was interrupted during download and am not able to add anymore of them. now i have talked to samsung care and they told me to bring my phone along with the bill maybe they can do it. even though my warranty is done for, but i think i can believe them . yet if there are any other suggestions pls tell me or should i give it to samsung care. I really don't wanna keep my phone rooted so i have no problem flashing stock but it's not happening. CAN KIES HELP?
p.s i have used all 1.85 , 1.87 and 1.83 version no use.
Click to expand...
Click to collapse
I fear your Note is done for, if your PC Odin session got interrupted.
chasmodo said:
I fear your Note is done for, if your PC Odin session got interrupted.
Click to expand...
Click to collapse
don't say that ... help me my situation is getting even worse now... will i be able to recover my phone!???! help me help me!
kunalteji1993 said:
don't say that ... help me my situation is getting even worse now... will i be able to recover my phone!???! help me help me!
Click to expand...
Click to collapse
Dont take it service centre.If you do so also dont say them you flashed custom rom.Then they wont fix it under warranty.Dont worry now.
Try different usb ports,uninstalling drivers and reinstalling it and try again.And as you are noob I recommend not to flash ICS customs at the moment.Stay with GB
I say go to your friend first who rooted your phone then ask him to try the various methods given in the forum recovering from softbrick.
i have read in some other websites that i will need a pit file to restore my phone + the rom file while checking repartition and auto time fe: reset in odin 1.83 then maybe i will be able to return back to gb . do u think this is ok for me to do .
p.s i live in chandigarh while my friend has moved to gurgaon so no chance to go to his place. and i have talked to customer care and told them everything. they told me to take the phone to service centre and they will help me.
now tell me what are my options!?
kunalteji1993 said:
i have read in some other websites that i will need a pit file to restore my phone + the rom file while checking repartition and auto time fe: reset in odin 1.83 then maybe i will be able to return back to gb . do u think this is ok for me to do .
p.s i live in chandigarh while my friend has moved to gurgaon so no chance to go to his place. and i have talked to customer care and told them everything. they told me to take the phone to service centre and they will help me.
now tell me what are my options!?
Click to expand...
Click to collapse
Ok now try to flash abyss kernel with red pill first lets see if it revives the phone.Yeah you are right pit file is required when you tick repartition and auto reboot and f.reset must be ticked all time.
vijai2011 said:
Ok now try to flash abyss kernel with red pill first lets see if it revives the phone.Yeah you are right pit file is required when you tick repartition and auto reboot and f.reset must be ticked all time.
Click to expand...
Click to collapse
wait . what? what is this red pill and all .. i think you can save me but i would liike you to brief me about the procedure plus i read this - i need a (wipe) rom to be able to reflash my rom or something like this .
p.s i am still downloading my firmware ...
but would be better if i get the info i need before hand!
dude.. don't panic... I don't think ur phone is dead... best is to buy a jig... try on eBay... I got it for 200rs in eBay... I don't think that's a big deal for any one with a note .. I bought it even before experimenting because I thought some thing like this might happen....
its safest way to remove the triangle and get into recovery mode... as somebody else suggested flashing red pill also works ... search in development section for abyss kernel... ull find it...
kunalteji1993 said:
wait . what? what is this red pill and all .. i think you can save me but i would liike you to brief me about the procedure plus i read this - i need a (wipe) rom to be able to reflash my rom or something like this .
p.s i am still downloading my firmware ...
but would be better if i get the info i need before hand!
Click to expand...
Click to collapse
its a kernel with a custom recovery.Its like CWM(Clock Work Mod).You could find it in the development section.Download the kernel.Could you get into recovery mode by turning off the phone,holding "vol up+home button+powerbutton"?
---------- Post added at 09:08 AM ---------- Previous post was at 09:00 AM ----------
kvsandeepreddy said:
dude.. don't panic... I don't think ur phone is dead... best is to buy a jig... try on eBay... I got it for 200rs in eBay... I don't think that's a big deal for any one with a note .. I bought it even before experimenting because I thought some thing like this might happen....
its safest way to remove the triangle and get into recovery mode... as somebody else suggested flashing red pill also works ... search in development section for abyss kernel... ull find it...
Click to expand...
Click to collapse
No need for jig because he can enter DL mode.And did using jig removed the yellow triangle for you
thanx guys for helping and current updates ---
i am in 12 th so untill my entrance exams are over i won't get to have the phone in my possession since my dad has it now ... so maybe after they are over i will continue on my quest to get it corrected!
well my note is all well except one thing. now whenever i connect note to kies it shows kies dpn't support upgrading of my device. my kernel is lc1 (inu)...
help pls?
kunalteji1993 said:
well my note is all well except one thing. now whenever i connect note to kies it shows kies dpn't support upgrading of my device. my kernel is lc1 (inu)...
help pls?
Click to expand...
Click to collapse
how did you fix it? this may help some else in the future
ratcom said:
how did you fix it? this may help some else in the future
Click to expand...
Click to collapse
service centre guys....remember he/she saying in pm
kunalteji1993 said:
well my note is all well except one thing. now whenever i connect note to kies it shows kies dpn't support upgrading of my device. my kernel is lc1 (inu)...
help pls?
Click to expand...
Click to collapse
wenn connecting to Kies at firmware Kies says something like LC1. lb2 (XXX) as product code? if so they have changed the board on the service center and they haven't activate the Pcode on your phone google "Pcode not active" you will find few posts till now only ppl from Germany had it who send their phones to service center via Saturn/Media Markt ist guess it was/is a technician you was sleeping on the seminare/briefing how to change the board on Note. hope it will help you if it is that try to replace your phone, had the XXX Pcode after service center got a replacement. after a month of arguing with the salesman.
Sent from my GT-N7000 using Tapatalk 2
Uninstall the Odin in your PC and install it again to see if it works.
i am pretty much sure that they didn't change the mother board. they must have added the firmware that's all as my mboard wasn't damaged at all , it was just that the battery failed when i gave it to samsung people that's why my phone overheated when they charged it and that's when the battery must have been destroyed maybe due to that overheating they must have thought to change mboard (but they didn't cause those engineers must have changed the battery prior to examining my phone for the problem). AND i didn't have pc odin on my THIS pc to start with. it was in my laptop and kies didn't even reckoned my phone there well that's why i installed kies on HERE . i guess service center people can update it the same way they installed this firmware here..... what do u suggest?
AND Braxos Pcode is active --- it's something :
GT-N7000ZBAINU
and no, the current firmware info kies shows is something like ---
N7000DDLC1/N7000ODDLC1/N7000DDLC1/N7000DDLC1(INU)
(now i think they have done something wrong - it's all n7000ddlc1 here. what is this? )
GUYS can u also tell me what does your firmware version shows (just for reference , pls do it!)
p.s my phone is still in warranty since they fixed my phone free of cost plus they also replaced the battery for free . before my phone was sent to service center my phone had a flash count of two yet they fixed it under warranty(yay!).And thank you everyone!
MY ADVICE TO NEWBIES----
If your phone is soft bricked and you don't know what to do and you think you will make the matter even worse then don't do anything to permanently brick it . you guys should go to service center , they might even fix it for u for free just like they did it for me!
Hey guys,
In a bit of a pickle at the moment. I grabbed an S1 off a friend to try and teach myself about rooting and flashing custom ROMs and such using Odin. With the final intent getting it to run ICS. Not a very hard challenge, but evidently it is for me.
I'll explain what I did, and if you can help without investing too much of your time I would be very grateful.
When I got it, it was running 2.3.3, all the tutorials I read told me to update it to 2.3.6 before doing anything more. I managed to root the phone easy enough, no issues there. But when I tried to put 2.3.6 on via Mobile Odin, (which I used to flash my S2 to ICS, long story) it had seemed to freeze on 'flashing flash kernel' for a good 15 or so minutes.
Being the daft monkey that I am, I exited the program...by removing the battery (don't judge me please). When I went to turn it on, it wouldn't load past the "Samsung Galaxy S" screen.
It goes into Download mode fine, and I've tried to flash an abundance of different Gingerbread ROMs onto the phone and Odin has just been getting stuck on the "setup connection" every time I've tried to flash.
I have tried using different USB ports which is readily suggested by most people and seems to work, using my laptop instead, different cords as well. No luck. Nothing happens when I press volume UP + home + lock like it used to, so I can't even factory reset or anything =\
I did find somewhere that suggested adding a PIT file to Odin and selecting repartition but every one yells at each other when 'repartition' gets mentioned, lol.
I hope this is in the right place, please bare with me if I used any wrong terminologies, I am relatively new to this.
Has anyone got some suggestions that may help me with my problem? =\
Thank you!
Taylor
sigh...here's my recovery kit, unzip, read .txt file, proceed
http://db.tt/MOGZx01S
Credits to nitr8 and chainfire
Thanks, sorry for being such a hassle...
Twinning92 said:
Thanks, sorry for being such a hassle...
Click to expand...
Click to collapse
No problems, was teasing ya! You will end up with root and custom recovery, if you then go to slim website and read and follow installation instructions you will then have lush ics
Morning all,
I apologise if this is in the wrong section but I am new to the forum and in a bit of pickle.
Around a week ago I rooted my lovely new note 3 to hopefully one day install some nice new ROM to get rid of the horrid touch wiz and actually see the full potential of the phones power. However, for some silly reason while I was using titanium backup on my phone I thought it would be a good idea to uninstall touch wiz thinking it would magically go back to basic android however it didn't. It is completely broken now, woops. The first issue I had was it would boot up and stick to the Samsung logo and just glow so I thought it would be an idea to install stock ROM via ODIN to try and revert it back to normal. Once I downloaded the correct stock ROM it was uploading through download mode however at the last minute it failed with a ext4 error which I think it means it's bricked? Not sure, completely new to this. I am now a bit stuck as I am not 100% sure what to do next.
The phone will only boot into either the firmware upgrade has encountered an issue, basically Odin mode or download mode. I have tried recovering it through kies however it cant connect to it. It knows it is there as it will start searching for it when it's connected however says it can't find it.
My phone is a note 3 SN SN-9005. The system status is custom, reactivation lock is off, Knox kernel lock 0x0, Knox warranty void 0x1 and write protection is enabled.
Obviously I would like to get the phone back to normal, I don't care if it has to be completely wiped and brought back to normal I would like it to just work. I've been an complete idiot and fiddled with something I'm not 100% sure on and I would like to not have a 600 quid paper weight hehe.
I will greatly appreciate any help or feedback.
You won't get the best feedback for a 9005 model here. We are the 900A version stuck on AT&T. Yes, however, we have plenty of intelligent people here. It's best to post your question here in the main Samsung Galaxy Note 3 thread next time:
http://forum.xda-developers.com/galaxy-note-3/help
Next, since you've voided your warranty as Knox being 0x1 - you're pretty much screwed for a refund or replacement based on PRESENT development from what I have read all over the AT&T threads. Understand this. Now, that being said, did you install a custom recovery or have your original recovery?
Here's my input/help. Forget about ODIN. You don't need that if all you did was remove your touch wiz.
Take out your battery, put it back in and hold VOLUME UP, POWER, and HOME together until you reach a recovery. Then if it's the stock recovery, wipe your cache partition, then wipe data/factory reset. Then reboot and you're good back to starting over. Check with a rooting application to see if you still have or not. If not, then obviously reroot
Also, don't ever do anything like that again without thinking what it could do, lol . Always tread carefully whenever you are new to something. Just my two cents for you. If you came here to root and learn it, don't be afraid to ask questions about applications and expanding your knowledge. No one will ignore you if you ask a simple question in the right manner/thread.
Good luck!
Thank you for the feedback. I have defiantly learnt from my mistake with this one. I have usually been lucky diving into things blindly hehe. I have tried to put it into recovery mode however it just vibrates like it should and then comes back up to firmware upgrade issue with the two computer screens an a attention sign in the middle. Is there anyway to get recovery mode back.
apdnote said:
Thank you for the feedback. I have defiantly learnt from my mistake with this one. I have usually been lucky diving into things blindly hehe. I have tried to put it into recovery mode however it just vibrates like it should and then comes back up to firmware upgrade issue with the two computer screens an a attention sign in the middle. Is there anyway to get recovery mode back.
Click to expand...
Click to collapse
Wish you had come here when you deleted touchwiz only instead of playing with Odin. Looks like you messed it up even further and have to now use Odin to reinstall your firmware. I'm about to go to sleep, but do this.
1) Take out battery and put it back in. Then press and hold VOLUME DOWN + HOME + POWER at the same time until you reach DOWNLOAD MODE.
2) Follow the steps here and use your odin or latest odin (shouldn't matter):
http://www.androidrootz.com/2013/10/how-to-unrootunbrick-galaxy-note-3.html
Oh, and google is your friend. It's how I learned things over the years...READING, then tinkering....you're welcome .
I wish I did as well. I will try this when I get back from uni this evening and post back results.
Thank you again.
apdnote said:
I wish I did as well. I will try this when I get back from uni this evening and post back results.
Thank you again.
Click to expand...
Click to collapse
You're very welcome, bro.
opasha said:
You're very welcome, bro.
Click to expand...
Click to collapse
I used what you have said to do and downloaded the correct firmware however when I try and install it via odin in download mode I get a FAIL(SIZE!) message at the end. Its not an ext4 error anymore but im worried at what is going on now. I have tried searching it up on google however nothing has come up. Looks like ive completely broken it... ='(
apdnote said:
I used what you have said to do and downloaded the correct firmware however when I try and install it via odin in download mode I get a FAIL(SIZE!) message at the end. Its not an ext4 error anymore but im worried at what is going on now. I have tried searching it up on google however nothing has come up. Looks like ive completely broken it... ='(
Click to expand...
Click to collapse
You have the 9005 right? I think you have the wrong file to odin. What is the exact model number of your phone and where are you located in the world? (reason I ask is there are different regions to choose from)
agent929 said:
You have the 9005 right? I think you have the wrong file to odin. What is the exact model number of your phone and where are you located in the world? (reason I ask is there are different regions to choose from)
Click to expand...
Click to collapse
SSN: SM-N9005GSMH
S/N: RF1D96B6ELB
United Kingdom Vodafone.
Im sure I downloaded the 9005 for samsung in the uk but I wil try again from a different site that specficly says what country and code.
If not would you be able to post me a link to the exact one?
Many thanks
Thank you so much everyone for your input. I hunted out the correct EU snapdragon firmware and booted it on, emptied the cache and restored to factory settings and its finally running! Only took 2 days hehe but at least its working. Thanks again everyone
Good to hear!
apdnote said:
Thank you so much everyone for your input. I hunted out the correct EU snapdragon firmware and booted it on, emptied the cache and restored to factory settings and its finally running! Only took 2 days hehe but at least its working. Thanks again everyone
Click to expand...
Click to collapse
Your welcome, don't forget to hit the thanks button for anyone that helped you!
apdnote said:
Thank you so much everyone for your input. I hunted out the correct EU snapdragon firmware and booted it on, emptied the cache and restored to factory settings and its finally running! Only took 2 days hehe but at least its working. Thanks again everyone
Click to expand...
Click to collapse
Hi, I am using same SSN. Can you please confirm the working rom download URL? Appreciate your help.
Thank you.