Open ports on the phone help needed REAL BAD!!! - Motorola Droid Bionic

I need to be able to access my FTP server from the Internet but all ports are closed.
My Bionic is my only connection to the Internet for my home network. I am using the Verizon Hotspot app and from my home network I can do anything I want to. This connectivity is great.
However, when away from home I need to access my FTP server on ports 21, 8080, and 443. I am using CrushFTP as my server. I have configured no-ip and from within CrushFTP it passes the built-in no-ip connectivity test, Thus my FTP server is reaching no-ip just fine. I check my IP that Google says I have against a ping to mydomain.no-ip.biz and the both match. But when I do a Sheilds-Up port scan, ALL ports are in stealth mode.
Next I loaded Port Forwarder on the phone and tried every connection to my laptop but still no luck. BTW, I connected the laptop directly to the hotspot taking out all routers and switches of my home network. Same results. The firewall is OFF on the laptop.
Then I downloaded a port scanner onto the pone. When I scan the phone's public IP, 70.201.1.55 port 21, 8080 etc are closed. So i tried scanning port 21 on my laptop's IP, 192.168.44.149 and it said OPEN. This proves the problem is not the laptop rather the phone.
After long talks with Verizon they assure me that they are not blocking inbound ports. I believe them because my neighbor has both a Bionic and a 3G hotspot stick. When he tries to get to his IP camera with the Bionic it fails. But if he connects his 3G stick, he CAN get to his camera.
I am willing to pay someone to get the Bionic to work! Or, if you know of a different phone that can do what I need to do, PLEASE PLEASE tell me. I cannot stress how important this is to me.
Thank You for reading.

Well it turns out that although Verizon does not block ports, your 4G phone in NATed and thus easily connecting from the Internet back to your system is not possible. Apps like LovMeIn do work just fine. But if you are trying to connect back to an FTP server, IP camera, etc, you cannot.
However, I was able to get me needs met by signing up for one of those VPN solutions AND getting a public IP from them too. I choose PureVPN and it is costing me $74/year for the service. I have a Microsoft Server 2003 running under VMware where my FTP server runs. I loaded the VPN client on the MS server and I can not access my FTP server from the Internet. I did setup the firewall for added protection.
Please note that your system will be fully accessible to anyone unless you set up a good firewall and block all um-necessary open ports. I put this server under VMware and it only runs the FTP server program for additional protection.
Good Luck!

Related

WM6: Ok, VPN: Ok, Remote Desktop: NOT Ok - HELP

Hello all,
I have been successful in loading the WM6 ROM: works great! I have been successful at using the phone for Bluetooth DUN. I have been successfull at setting up a VPN connection to my place of employment: I can look at the RRAS server GUI and see that I have established a viable connection.
What I have NOT been successful at is getting Remote Desktop to work. RD is one of the reasons I upgraded to this ROM. Has any one been able to get their Windows desktop on their Treo? If so, how did you do it?
I can't seem to find any pertinent information on how to make this work so anything you can tell me would be a great help.
Cheers,
idyllic
http://forum.xda-developers.com/showthread.php?p=1453117#post1453117
http://forum.xda-developers.com/showthread.php?p=1451613#post1451613
joannaex said:
http://forum.xda-developers.com/showthread.php?p=1453117#post1453117
http://forum.xda-developers.com/showthread.php?p=1451613#post1451613
Click to expand...
Click to collapse
Joannaex,
thank you for the forum pointers. Alas, they did not help. I did try to load the cab file from one of the threads, but it loaded the same version of Remote Desktop Mobile that I already had. I still get the same errors encountered with the previous version. Maybe this behavior is due to the "unofficial" ROM not being fully functional in some way? I don't know. It would be interesting to hear from someone that actually got this to work.
Cheers
idyllic
PS: in occurs to me that this might be a routing issue in the 10.x.x.x/192.x.x.x space. I could verify this if there were a command prompt where I could run things like ipconfig, tracert, netstat, etc. Or a log file that could be viewed. Just wishful thoughts I suppose
PPS: Just found two great progs, one called VXIPCONFIG which give you the info you would get in you did an ipconfig /all. The other is called VXUTIL which you can do PING, TRACERT, WHOIS and a lot more. The utilities are available from http://www.cam.com/windowdsce.html.
I have been able to connect to remote desktop. What has been successful for me has been to already initiate my 3G connection then connect using remote desktop. It doesn't seem to be able to start up the connection itself.
andokai said:
I have been able to connect to remote desktop. What has been successful for me has been to already initiate my 3G connection then connect using remote desktop. It doesn't seem to be able to start up the connection itself.
Click to expand...
Click to collapse
andokia,
I am doing the exact same thing: starting my 3G connection, then my VPN connection, and lastly Remote Desktop Mobile. The RDN ALWAYS times out with one of these two errors: "Connection Status - Cannot Connect. Likely reasons are: 1. Specified computer name or IP does not exist, 2. A network error occurred while establishing a connection." So, I'm kind of at a loss here as the troubleshooting tools available are not great. Thank you for the response!
Cheers,
idyllic
Hi idyllic,
Can you access a remote desktop when a VPN session isn't active? I have used the two separately without problems but haven't tried them together.
andokai said:
Hi idyllic,
Can you access a remote desktop when a VPN session isn't active? I have used the two separately without problems but haven't tried them together.
Click to expand...
Click to collapse
andokia,
no, I cannot access any system. I have tried my home system (firewalls turned off and on). I have tried my work systems (VPN on and off). Nothing seems to work. It's really frustrating to have a tool that you know can help you, but it doesn't work: aaaaaaaaaaaahhhhhhhhhhhhhhhhhhhhhhhh!
Cheers,
idyllic
I'm assuming you're trying to use a local address because you are connecting with vpn first. Did you put the local address in the exceptions list? If not the vpn connection will disconnect anytime you try to use an address that is not in the exceptions list.
Exceptions list: start\settings\connections\connections\advanced\exceptions
then add the local url
Hope this helps. Used to be the problem I had when trying to use VPN.
chris44gw said:
I'm assuming you're trying to use a local address because you are connecting with vpn first. Did you put the local address in the exceptions list? If not the vpn connection will disconnect anytime you try to use an address that is not in the exceptions list.
Exceptions list: start\settings\connections\connections\advanced\exceptions
then add the local url
Hope this helps. Used to be the problem I had when trying to use VPN.
Click to expand...
Click to collapse
chris44gw,
yes, I'm trying to connect to a local addres, but that address isn't a URL. The address I'm entering is an IP address of the machine for which I want to get a desktop. Now maybe I'm wrong, but my understanding is that I can use Remote Desktop Mobile to get, say, a desktop/console of one of my servers.
I've been able to surf the web on the phone, I've been able to use the phone as a Bluetooth modem, I've been able to connect to each of my companies VPN servers. Still now desktop. Whether I enter a fully qualified domain name or an IP address it never works.
Now, I have a little more information. If I just connect to the AT&T 3G network I can do a traceroute to the VPN servers. If I then connect to the VPN (PPTP connection verfied and active) I CANNOT ping anything on the corp. net. It has to be a routing issue I'm thinking. It seems that it needs to be fixed on the phone side, but I can't seem to figure out where to do this.
Anyway, I appreciate the pointer about the URL exception list.
Cheers,
idyllic
That's what mine looks like. Once I'm connected vpn wise into my 2003 server I can RDP into it and another XP machine on the network through the local IP. Only thing I can think of is if you have activesync connecting to an exchange server. It might disconnect the vpn. I think you've said you're verifying the vpn connections so I might look into the firewall on the computer or make sure RDP is on for the computer (although you've probably done that). Good luck though.
chris44gw said:
That's what mine looks like. Once I'm connected vpn wise into my 2003 server I can RDP into it and another XP machine on the network through the local IP. Only thing I can think of is if you have activesync connecting to an exchange server. It might disconnect the vpn. I think you've said you're verifying the vpn connections so I might look into the firewall on the computer or make sure RDP is on for the computer (although you've probably done that). Good luck though.
Click to expand...
Click to collapse
chris44gw,
thank you for the screen-shot. I gave this a try, but no luck. We don't use exchange servers at work and I've verified that no active sync is active during the connect process. Having downloaded a couple of tools to help troubleshoot, I've noticed that I CANNOT ping anything on the internal network: this after verify that the VPN connection active and viable. I have also verified that each system that I am connecting to has RDP turned on. I guess I'll just keep experimenting. I just can't help but think that there is ONE LITTLE THING that is keeping this from working.
Cheers,
idyllic
PS: What encryption level does the Treo 750 VPN app use? 56bit? 128?
PPS: Upon further testing... when I connect to the RRAS server (and connecting to the RRAS server has NEVER been the problem) on the West Coast (Windows 2000 Server std. SP4) I cannot ping the "inside" network. When I connect to the East coast RRAS server (Windows Server 2003 SP2) I CAN ping "inside" network. In either case I still cannot get a remote desktop.
Have the same problem on Diamond
Hi all,
After upgrading to wm6.1 on O2 Diamond unable connect to Remote Desktop.
When manually connected to Internet it works perfect, but from RD Client there is always an error (dial up or Proxy settings). All other programmes can always correctly initiate internet connection via GPRS/UMTS. Via Active sync RD works always.
MFG
Sorry, never got it to work. Call me a traitor, but I now have an iPhone and everything works the way I expect it... with two major exceptions: 1. no cut-and-paste, 2. can't be used as a tethered modem without jail-breaking the phone (which I'm not willing to do).
--idyllic
Similar problem HTC Touch HD
Hi all, sorry in advance if my problem ends up being because I've missed something basic; I'm trying to setup RDC on my HTC Touch HD with no luck. Computer name is right, password is right, IP is right. Fail message:
"connection status. cannot connect. likely reasons are: 1. specified computer name or ip does not exist. 2. A network error occurred while establishing the connection."
I'm connected to my WiFi network which also has the machine i'm trying to connect to on it. I've also tried when out of network range, connecting via 3G/HSDPA. Steps I've taken:
-Enabled remote desktop in system properties on target machine. Haven't added any remote users as it already allows me (admin on target machine) and I'm using those login details to access.
-Allowed RD in the packet settings of Kaspersky antivirus, using the address as the ip of my mobile, found by going to whatsmyip.com, and name as the name I've set on the device.
-Probably unrelatedly, I've also allowed the HTC to access the wifi through the MAC address access list
I can connect via a standard windows machine on the same router (which just needs the computer name, not the IP). Have found this useful as I had the details around the wrong way, but even now it's not working. Based on the tips in the link above, I'm under the impression that I should set things up thus:
Computer: the ip address of target machine
User name: EITHER my username OR MACHINENAME/User Name, e.g. John Smith OR JOHNSPC\John Smith
Password: pw
Domain: either machinename or blank.
Anyone know if this is right / which of the options for username and domain is right?
Cheers
Dez

WM6 internet sharing with whole network

Hi, I have a Tilt and do not have a problem tethering to a single computer. What I would like to do is share with all four computers in my home. I have tried bridging the sharing connection to my lan connection and have gotten dhcp on the Tilt to assign addresses to all computers on the network, but they still can't ping each other (other than the tilt and the computer its directly tethered to. I have turned off all firewalls and still nothing. Rebooted everything. Still nothing. Is it possible to do this? Thanks for any help.
There's a program around here somewhere that allows you to make your TILT a wireless router. If you do this, any machine with wi-fi can connect to the SSID and go.
Anyone have the link handy?
Wireless Router
Could I have it connect with my current wireless router to provide internet to my wired network through the rj45 ports on the router ? 3 of the 4 computers are on a wired lan. You see, we just got HSDPA on Monday and I love it. I got a bit ahead of myself and cancelled my home DSL connection. Now I'm realizing that I am stuck with only having one computer on the internet at a time. This has got to be possible. - I just found the thread on setting up as a wireless router. I will start playing with it. Any suggestions/instructions are appreciated.
OK, get connected to your carrier whilst tethered.
Then from any Explorer window on your tethered PC, select, 'Set up a home or small Office Network'.
Select the first option in the following box 'This computer directly connects...' and follow it through.
This should set up your Activesync PC as an IP address of 192.168.1.1. (an access point IP)
If you connect any other PC/laptop to this PC via wireless or LAN (you do know how to do that I hope??) to this computer, it will share the internet connection..
Remember, this will change any prior Internet configuration you have on the PC/Laptop!
Hope this helps.
Internet sharing
Thanks for the suggestion. I am going to try that again. The first time I tried that I found out that the Tilt had already assigned itself the address of 192.168.0.1 . On the XP machine, the computer will always use that same address to share its connection, so it immediately complained that another computer on the network is already using the required address for internet connection sharing. Maybe all I need to do is force the Tilt to use a different ip address like 192.168.0.10? I am not sure how to do that since this is my first time using Windows Mobile as part of a network sharing its connection. The only reference I could find to 192.168.0.1 in the registry was HKLM\Comm\BTPAN1\Parms\TcpIp. Should I change that?
jebrown1 said:
Thanks for the suggestion. I am going to try that again. The first time I tried that I found out that the Tilt had already assigned itself the address of 192.168.0.1 . On the XP machine, the computer will always use that same address to share its connection, so it immediately complained that another computer on the network is already using the required address for internet connection sharing. Maybe all I need to do is force the Tilt to use a different ip address like 192.168.0.10? I am not sure how to do that since this is my first time using Windows Mobile as part of a network sharing its connection. The only reference I could find to 192.168.0.1 in the registry was HKLM\Comm\BTPAN1\Parms\TcpIp. Should I change that?
Click to expand...
Click to collapse
NO, 192.168.0.1 or 2.1 or.3.1 are all access point AD's.
You have to go into your PC/laptop Network Places icon to tel IT to then share the connection.
I am sorry, but if you have never shared an internet connection on your PC before (ie via modem or ADSL), you will not really understand how it is done.
Access points
Thanks for your reply. The problem is that we are trying to make the pc an access point and trying to make the tilt an access point at the same time. They both are using 192.168.0.1 as the default ip address and as far as I tell there is not a way given to change that. The Tilt automatically uses 192.168.0.1 and when you using the sharing wizard on the pc it also uses the same address for its network card thats connected to the home wired network. Unfortunately for me, two devices on a network cannot have the same ip address. There must be a way...
jebrown1 said:
Thanks for your reply. The problem is that we are trying to make the pc an access point and trying to make the tilt an access point at the same time. They both are using 192.168.0.1 as the default ip address and as far as I tell there is not a way given to change that. The Tilt automatically uses 192.168.0.1 and when you using the sharing wizard on the pc it also uses the same address for its network card thats connected to the home wired network. Unfortunately for me, two devices on a network cannot have the same ip address. There must be a way...
Click to expand...
Click to collapse
OK, set all computers on the network to fixed IP's of 192.168.0.xxx in Internet protocol (under TCPIP on network)with the same subnet mask with a default gateway matching your device! Try that...
sharing
That was my first attempt at a work around. The problem is that there are
actually two network connections to the pc. One for the Tilt (usb) and one for the LAN (nic card). They don't seem to see each other even when they have matching ip addresses and subnets. Thats why I tried right clicking them and selecting "bridge these connections." It seems that internet sharing "requires" DHCP to be used. I tried setting all the computers to use DHCP and actually had the Tilt assigning ip addresses to all of the computers on the network by bridging the two connections and using dhcp. Oddly, though, the computers on the network could not ping the Tilt. I think its because bridging uses the data link layer of the osi networking model?
There must be a hack to change the ip address that windows uses for the sharing access point. Alternatively, it would be nice if there were a device out there that could act as a hub to network usb and 100baseT devices together. In other words, plugging usb and cat5 cable rj45 plugs into the same box and having them all be on the same network.
OK, I have asked smitty to get on this but both of us are WAYYYYy past our bedtimes.
He should get back to you tomoz on this. (he's the Network buff..)
Hope it works out..
this is the app mentioned earlier and may help your solution...
http://forum.xda-developers.com/showthread.php?t=341398
I can't make this work. I don't have WiFi on all of my computers. I was hoping to use WMWifiRouter to connect to my wireless router and then to my whole wired network. Is there a way to make the Tilt wireless router to connect with another wireless router? I'm thinking what I will do is go back to an AT&T rom and use "wireles modem" instead of "internet sharing". That way I can share the modem with the whole network. There doesn't seem to be a good way to use the Tilt internet sharing with the whole network. What do you guys think?
Deleted.....
For any future readers of this thread: I put the stock AT&T rom back on this phone and did a soft reset during the initial boot to stop the bloatware from loading. I went to start>settings>connections and tapped the wireless modem icon to open the app. I selected "usb" and tapped done then plugged the usb into my computer. My win xp computer found the new modem hardware and installed the HTC modem driver. I then setup a new dialup connection on my computer, and used the following to setup the login and dial:
username: [email protected]
password: cingular1
dial #: *99***1#
When I clicked on dial, it quickly connected to the AT&T network and I had internet access on my computer! I went to a speed test website and clocked my download speed at 1.2mbs and upload at 300kbs. I then opened "my network" and started the network setup wizard. I selected "this computer connects directly to the internet" and "file and printer sharing". To make a long story short, I am now able to share the Tilt's HSDPA internet connection with my whole network! I could not do it using the internet sharing function of the Tilt with either the AT&T rom or the kaiser rom. It would be awesome if someone more educated than me could make this function part of the HTC kaiser rom.
Nojnaworb wrote:
.....the problem is that we are trying to make the pc an access point and trying to make the tilt an access point at the same time. They both are using 192.168.0.1 as the default ip address and as far as I tell there is not a way given to change that. The Tilt automatically uses 192.168.0.1 and when you using the sharing wizard on the pc it also uses the same address for its network card thats connected to the home wired network. Unfortunately for me, two devices on a network cannot have the same ip address. There must be a way.......
I have same problem. I agree with Nojnaworb, this is the reason why its not working.
I have no Wifi at home and have to use LAN for my home network (2 PC + 1 ppc).
Under WM5 it was easy to share Internetconnection with all Lan adapters.
I cannot believe there is no way.
PLS Networkexperts, tell me how to setup !!
Its really quite simple.
You dont connect all the computers to the tilt. You use ICS on the tilt to provide one pc with an internet connection.
You then share the internet connection from that pc to the other pc's using the networking wizard.
I think part of this persons problem was that he needed to bridge the 2 connections.
here have this.
http://www.windowsnetworking.com/articles_tutorials/wxpbrdge.html
You should be able to connect the Tilt, (let it use whatever address it wants) and then make a bridge from the tilt to your nic in the server. Then I beleive you just use internet connection sharing to disperse the lovely packets to the rest of the network. Without the bridge, there is no way to share from one network to another.
I'm pretty sure that you will need to set the address to 192.168.0.2 on the server or any other number were the 2 is. If your using a router then I would suggest turning off dhcp and not using the WAN port on it. Just treat the router like a switch/hub because it will just makes things even harder to figure out.
wish we had service that was worth sharing to my network.

Need to do one of two things... or both?

Ok, well basically my end need is to have my Google Calendar synced to my phone on which I have no service or access to WiFi internet. I'm in Iraq right now, and the only internet I have is via Ethernet.
I am hoping to, at the least, sync my calender over USB. But one thing I'd love to do is share my internet connection to my phone via USB like WinMo does. That way I can mess with new roms and the such while I'm out here. Thing is, it can't have it's own IP address because all IP's are assigned and I have to log in via my browser on my computer once I'm connected. It's a pain in the ass.
But, any help would be great. Thanks!
I am pretty sure there is not a way to do what you are asking. Without wifi or and kind of data signal, there is no way to connect the gmail servers to your phone. I am pretty sure that usb is out of the question, which seems to be your only option.
Sorry my friend.
This might help, all you need is linux. You could virtualize it, but idk if you can do that where you are at right now.
any possibility of getting a usb wifi device and setting up Internet Connection Sharing so your phone would have a local ip like 192.168. and share the connection on your computer with your phone???
I don't know exactly how the IP shiz works with ICS, but the ISP out here uses 192.168 IP's. All I know is that the phone would need to not have an IP, or something along those lines, for it to work. IDFK....
If you're in iraq, it might be hard to get your hands on one of these, BUT, in the interests of completeness,
Use of a regular cheap broadband router with integrated wifi WILL do what you are looking to do...
You might need to clone your computer's MAC address to the router's WAN device, then it'll connect to the DHCP server, then using EITHER the computer OR the phone, go to the browser and authenticate.
Note: I don't think that there is really any way to network the phone to the computer using USB, though bluetooth IS an option... it'll be a console-only operation though.
Final option is to get your hands on a wifi device for the computer (can be a USB device) and run it as a NAT, i.e. use iptables.
my95z34 said:
Ok, well basically my end need is to have my Google Calendar synced to my phone on which I have no service or access to WiFi internet. I'm in Iraq right now, and the only internet I have is via Ethernet.
I am hoping to, at the least, sync my calender over USB. But one thing I'd love to do is share my internet connection to my phone via USB like WinMo does. That way I can mess with new roms and the such while I'm out here. Thing is, it can't have it's own IP address because all IP's are assigned and I have to log in via my browser on my computer once I'm connected. It's a pain in the ass.
But, any help would be great. Thanks!
Click to expand...
Click to collapse
lbcoder said:
If you're in iraq, it might be hard to get your hands on one of these, BUT, in the interests of completeness,
Use of a regular cheap broadband router with integrated wifi WILL do what you are looking to do...
You might need to clone your computer's MAC address to the router's WAN device, then it'll connect to the DHCP server, then using EITHER the computer OR the phone, go to the browser and authenticate.
Note: I don't think that there is really any way to network the phone to the computer using USB, though bluetooth IS an option... it'll be a console-only operation though.
Final option is to get your hands on a wifi device for the computer (can be a USB device) and run it as a NAT, i.e. use iptables.
Click to expand...
Click to collapse
They don't care what the MAC is, just IP's. I can get a WiFi router if I need to. But, if I turn off DHCP on the router, does it still need it's own IP address? Or does it just act as a switch? All IP configuration is done on the device, there is no DHCP ran by the ISP.
my95z34 said:
They don't care what the MAC is, just IP's. I can get a WiFi router if I need to. But, if I turn off DHCP on the router, does it still need it's own IP address? Or does it just act as a switch? All IP configuration is done on the device, there is no DHCP ran by the ISP.
Click to expand...
Click to collapse
The cheap broadband router has TWO IP addresses. The public IP address assigned by the ISP's DHCP server (or manually if the ISP doesn't have DHCP), and the PRIVATE IP address used to communicate with the other devices that you hook up to it. It uses NETWORK ADDRESS TRANSLATION (see http://en.wikipedia.org/wiki/Network_address_translation ) to connect the client machines to the public network. To the public network, it appears that there is ONLY ONE machine connecting -- the NAT box (router) itself.
You will leave the DHCP *SERVER* (LAN SIDE) running on the router, you will disable the DHCP *CLIENT* (WAN SIDE) and configure the WAN IP/NETMASK/DNS/GATEWAY to the specifications required by the ISP. You will use the router's WAN port to connect to your ISP, you will use any LAN port to connect to your computer, and you will use the WiFi to connect to your phone. You will then have private IP addresses assigned to your computer and your phone, and these devices will be able to connect through your ISP's network via the router.
So doing that the ISP will see my router as my computer, then both my phone and computer can connect at the same time because they'll have their own private IP?

reverse tether, ad-hoc, on mac filtered network?

I have a rooted N1 with cyanogen 5.0.4.1 on it.
I'm studying abroad this semester, and the university I'm at seems to have done everything they could to prevent me from connecting my phone to the internet on their network.
There is a wireless network, but it doesn't reach my room, and there's a proxy; I haven't been able to get any of the various proxy apps to work with it, at all. On a somewhat related note, since moving to cyanogen I'm not able to connect to that network anymore (wpa enterprise, tls/pap/user+pass). No real loss, since it didn't work as I couldn't get the proxy going.
The rooms have ethernet, with a static IP and mac filtering, and of course the same proxy. In addition, on the wired network in the rooms you have to connect to a vpn in order get anything other than the school's intranet
With cyanogen's rom, I have been able to connect my phone to my computer's ad-hoc network by giving it the parameters (IP, gateway, netmask, dns), that were provided to me, but I can't download anything. My only guess as to why that's not working is their static IP/mac filtering combo is not playing nicely.
I haven't ever delved very deeply into networking type stuff such as proxies, ssh tunnels, etc, so these two ideas of mine could be completely unworkable, but what I've been able to come up with is:
1. Is there a way to have my laptop keep handling all the proxy/ip/vpn nonsense, and just route http data to and from my phone? I've never dealt with ssh or anything of that sort, but I run linux so it should be pretty trivial to get it set up on the laptop's side of the equation.
2. Failing that, I'm allowed to have 3 devices with 3 different mac addresses, each of which is given a separate IP address, so I give the people in charge of the network the mac address for my phone and get an IP address for it. Then, connect to my laptop's ad-hoc network, which is on IP #1, and go to the advanced wifi settings on my N1 and set up a static IP with IP #2. Does that work, at all? This of course doesn't account for the vpn at all, but if it does in fact work I'd then move on to that.
What a ****ing brain-buster. Goodluck!
As an update, I can use cyanogen's included tethering ability, in conjunction with ConnectBot, to ssh from my phone to my computer (got that working after a bit of work, and learned something new). However, when I try to set up port forwarding in ConnectBot, it doesn't work; I don't know which ones to forward, whether to choose local or remote, and if I try to forward something below 1024 it gives me an error because of that. Does anybody know what ports I need to forward, and how to do that properly with ConnectBot?

VPN access/useragentswitcher/ or a way to bypass isp packet sniffers.

Is there any way to connect to internet via VPN (PPTP, L2TP-IPSec, or OPENvpn). Is it possible to install the necessary system/binary stuff to be able to so through adb, ssh, or telnet. I am connected to the internet through my phones hotspot, my laptop is connected to VPN. And when I am not connected to VPN for any reason I can make the chrome useragent changer to appear as an ubuntu or linux machine running chrome. When the content being requested is local on laptop plex media server and requesting it through patched plex it can play just fine, and that is with the laptop connected to internet via VPN, when I try to play something on plex that is streaming it just hangs like it wants to play but doesn't load. when I attempt to play streaming media via AVIA I get sent to the 4gLTE ISP provider (tmobile) upsell page that appears when they sense that you have something connected via wifi hotspot tether. I think that when plex is hanging at the loading page that it is also getting the upsell page but it just doesn't show up on the screen. If it is possible to make the CC connect through VPN or change the user agent of the chromecast I should be able to bypass the upsell page that is saying I can't connect via wifi tethered devices. This makes me think that the dns servers I have set in eureka web panel may not actually be making their connection through the servers from openNIC that I set it to use. The chromecast can communicate with my laptop when it is connected to VPN simultaneously without a problem.
Is it possible to innstall the privateinternetaccess PIA VPN app on the chromecast and add it to the eurekarom whitelist? or any openvpn app will work so other people with different vpn providers can also connect with the correct configuration files in place. Or does anyone know how to make the chromecast go through VPN that is active on phone, like the way a router that is connected to VPN makes all of the clients connected to it go through the VPN without the need to sign in to the vpn on each device.
Here's how I did it !!!
I'm also tethering via T-Mobile & ran into the same problem as you !!! What I've done before the 15250 update was run an app named Network Spoofer downloaded from blackmart app // I turned hotspot on my phone & my Asus Tf700 was connected to the WiFi created by t mobile I used VPN unlimited & while its connected // I ran the Network spoofer app & I either use adblock *** or redirect traffic through phone - this being the most often used option !!! After selecting redirect // I selected default gateway // I then chose the IP address that my chromescast is using // the chromecast name under IP address sometimes doesn't show up // so you'll have to know what your chrome cast IP address is // you can find this by using the chrome cast app !!!
The network spoofer app, found on sourceforge doesn't function correctly on nexus 4, at least not for me.
I ran into the same problem. Plex Media Server would not work on T-mobile tethering. I tried Network Spoofer and used Redirect Traffic Through Phone and give it the ip address of the the laptop that hosts Plex Media Server, it didn't work. Even the browser on this laptop would bring up the T-mobile upsell page. It seems this feature would simply let everything pass through the phone.
Any other suggestion?
Here's my setup
An LG phone with T-mobile LTE attached to my router via USB tethering. The router then serves every device, wired and wireless, on my network. Roku and all PCs works fine if I change the User Agent of the browser. Only the Plex Media Server would cause T-mobile to bill the traffic against the limited 2.5G tethering, the rest got billed against the unlimited data plan.
1.connect windows PC to wifi/usb tether connection
2.connect computer to VPN
3.create WiFi hotspot on CPU via
"Solution A
- Go to*Control Panel*>*Network*/*Network and Sharing Center
- Go to*Set up a new connection or network
- Go to*Set up a wireless ad hoc (computer-to-computer) network
- Add a Name and Password (and set the security type onWEP) and Checked*Save this network*and press*Next
- [Windows 8.1] Confirm*Turn On*Internet Connect Sharing
- [Windows 8, 7 or Older] Right Click on available network and select*Properties*and go to*Sharing*Tab and checkedAllow other network users to connect through this computer's Internet connection
Solution B
- Go to*Control Panel*>*Network*/*Network and Sharing Center
- Go to left sidebar and select*Manage Wireless Networks
- Go to top left and select*Add
- Go to*Set up a wireless ad hoc (computer-to-computer) network
- Select*Next
- Add a*Name*and*Password*(leave security type on*WEP) and Checked*Save this network*option
Solution C
- Press*Windows Key + R*and type*ncpa.cpl
- Select current WiFi Adapter and Right Click on it and select*Properties
- Go to*Sharing*Tab and checked*Allow other network users to connect through this computer's Internet connection
- [WINDOWS 8.1]: go to left bottom screen and selectCommand Prompt (Admin)
- [WINDOWS 8, 7 or Older]: Press*Windows Key + R
- Change PASSWORD 12345678 and SSID AMASTANEH in below text and type it on black terminal screen
netsh wlan set hostednetwork mode=allow ssid="AMASTANEH" key="12345678"
- you can start and see the ready network with this command
netsh wlan start hostednetwork
Solution D
- Download Virtual Router (Wifi Hot Spot for Windows 8, Windows 7 and 2008 R2) fromhttp://virtualrouter.codeplex.com/
- Install and Run and Enjoy
Solution E
- Download*Connectify from*www.connectify.me
- Install and Run and Enjoy "
4.connect chromecast to wlan hotspot created in step 3
Step 3's source comes from here
http://blog.amastaneh.com/2014/01/how-to-create-windows-wifi-hotspot.html?m=1
smartymcfly said:
1.connect windows PC to wifi/usb tether connection
2.connect computer to VPN
3.create WiFi hotspot on CPU via
"Solution A
- Go to*Control Panel*>*Network*/*Network and Sharing Center
- Go to*Set up a new connection or network
- Go to*Set up a wireless ad hoc (computer-to-computer) network
- Add a Name and Password (and set the security type onWEP) and Checked*Save this network*and press*Next
- [Windows 8.1] Confirm*Turn On*Internet Connect Sharing
- [Windows 8, 7 or Older] Right Click on available network and select*Properties*and go to*Sharing*Tab and checkedAllow other network users to connect through this computer's Internet connection
...
Click to expand...
Click to collapse
Hi smartymcfly,
Thanks for the info. It seems step 3 above is to turn the laptop into a wifi hotspot. However, In my case the laptop is already visible throughout the whole network because it's attached to the router via an ethernet cable. The router gets its internet from the USB port attached to a smart phone and all devices attached to the router.
Based on your instruction (step 2) is to connect to a vpn. I will try to run Hotspot Shield on the laptop to see if that helps. My router is an Asus wl-520gu running DD-WRT so I think it has builtin VPN server, I will try that too.
By the way, did you get your Plex Server to work without T-mobile upsell? Thanks
slick3r said:
I ran into the same problem. Plex Media Server would not work on T-mobile tethering. I tried Network Spoofer and used Redirect Traffic Through Phone and give it the ip address of the the laptop that hosts Plex Media Server, it didn't work. Even the browser on this laptop would bring up the T-mobile upsell page. It seems this feature would simply let everything pass through the phone.
Any other suggestion?
Here's my setup
An LG phone with T-mobile LTE attached to my router via USB tethering. The router then serves every device, wired and wireless, on my network. Roku and all PCs works fine if I change the User Agent of the browser. Only the Plex Media Server would cause T-mobile to bill the traffic against the limited 2.5G tethering, the rest got billed against the unlimited data plan.
Click to expand...
Click to collapse
This might not be directly related but here is a little something I learned....
I have PMS with a VPN. There are a few things you need to set up before you can get it to work. (Also works for vudu)
Basically, the VPN won't work because it needs access to a few IP addresses that it can communicate directly with the myplex servers but not through the VPN. I did tons of packet sniffing to figure these IP addresses out..
What happens is, if you are connected to the VPN, ALL outgoing traffic goes through the VPN and the Plex servers don't understand where that traffic came from and will block it. If your server is reported as being at one address and the traffic comes from another, that makes it look like something is spoofed.
If you have a firewall or VPN that can separate your traffic, I have the IP addresses for you.
The good thing is, the IP address ranges that you'll input, don't effect how your channels are retrieved; meaning that you can still get international channel content from channels like BBC iPlayer or CBC.
I had to use a very special feature on my firewall called ISP Redundancy and route traffic to certain IP ranges directly to the source. This also helped with Verizon FiOS throttling stuff like Netflix and Vudu.
Sent from my Nexus 7 using Tapatalk
abuttino said:
This might not be directly related but here is a little something I learned....
I have PMS with a VPN. There are a few things you need to set up before you can get it to work. (Also works for vudu)
Basically, the VPN won't work because it needs access to a few IP addresses that it can communicate directly with the myplex servers but not through the VPN. I did tons of packet sniffing to figure these IP addresses out..
What happens is, if you are connected to the VPN, ALL outgoing traffic goes through the VPN and the Plex servers don't understand where that traffic came from and will block it. If your server is reported as being at one address and the traffic comes from another, that makes it look like something is spoofed.
If you have a firewall or VPN that can separate your traffic, I have the IP addresses for you.
The good thing is, the IP address ranges that you'll input, don't effect how your channels are retrieved; meaning that you can still get international channel content from channels like BBC iPlayer or CBC.
I had to use a very special feature on my firewall called ISP Redundancy and route traffic to certain IP ranges directly to the source. This also helped with Verizon FiOS throttling stuff like Netflix and Vudu.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Hi abuttino,
Thanks for the info. I'm ordering a new, more powerful router and should have it by tomorrow. I will be using DD-WRT firmware on this new router. DD-WRT should have builtin VPN and firewall. I've been reading on the firewall features, and it seems that it allows routing traffic both ways based on ip addresses. What I'm not sure about his whether or not the routing is running inline with the vpn or can be set to run parrallel so we can have some traiffcs encrypted and some are not.
So for the exception to the IP addresses that need unencrypted communications, do they require both ways (from internet to Plex and from Plex to internet) or just one way?
They need to run in both directions. I'll give you the IP ranges when you are ready, but be prepared to run wireshark to sniff out more IP addresses if myPlex doesn't connect
Sent from my Nexus 7 using Tapatalk
abuttino said:
They need to run in both directions. I'll give you the IP ranges when you are ready, but be prepared to run wireshark to sniff out more IP addresses if myPlex doesn't connect
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Hi abuttino,
I bought an Asus RT-N66U thinking I was able to use Android usb tethering (Asus said that it could) but I haven't been able to get it going. I must be able to use this router with usb tethering first before configuring VPN. Thank you. I will keep you posted.
slick3r said:
Hi abuttino,
I bought an Asus RT-N66U thinking I was able to use Android usb tethering (Asus said that it could) but I haven't been able to get it going. I must be able to use this router with usb tethering first before configuring VPN. Thank you. I will keep you posted.
Click to expand...
Click to collapse
Does the RT-N66U have a server and dlna function that can be used with Bubbleupnp?
slick3r said:
Hi smartymcfly,
Thanks for the info. It seems step 3 above is to turn the laptop into a wifi hotspot. However, In my case the laptop is already visible throughout the whole network because it's attached to the router via an ethernet cable. The router gets its internet from the USB port attached to a smart phone and all devices attached to the router.
Based on your instruction (step 2) is to connect to a vpn. I will try to run Hotspot Shield on the laptop to see if that helps. My router is an Asus wl-520gu running DD-WRT so I think it has builtin VPN server, I will try that too.
By the way, did you get your Plex Server to work without T-mobile upsell? Thanks
Click to expand...
Click to collapse
Sorry for the untimely response...
in step 2, in your case you would need to connect your router to VPN
or
Connect computer to VPN, create hotspot and have your chromecast connect to newly created hotspot but this way would defeat the need to use the router. This the way I have it. There is also an app named klink that may allow you to connect phone to VPN and push all traffic through VPN but I do not know how well it works or if it will work with chromecast.
slick3r said:
Hi abuttino,
I bought an Asus RT-N66U thinking I was able to use Android usb tethering (Asus said that it could) but I haven't been able to get it going. I must be able to use this router with usb tethering first before configuring VPN. Thank you. I will keep you posted.
Click to expand...
Click to collapse
You may need to update the routers firmware. Or install one that will allow it.
http://support.asus.com/FAQ/Detail....DB9-CC0E-5F67-85F7D3FB48E4&m=RT-N66U+(VER.B1)
"B. Update the firmware to version 3.0.0.4.268 or later"
http://www.flashrouters.com/routers...router-tomatousb-router-privateinternetaccess
If you use privateinternetaccess for your VPN their is a Tomato firmware customized for it Tomato Version:*K26VRT-N
It lists the firmware.
http://www.flashrouters.com/tomato-firmware-router-information
https://gist.github.com/joshenders/3941269

Categories

Resources