Related
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
A few questions:
spazlon said:
I tried installing a custom ROM on my 7310 and it had issues.
Click to expand...
Click to collapse
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop.
Click to expand...
Click to collapse
How far into the boot sequence does it get?
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Have you tried seeing what is causing the boot-loop using adb?
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Click to expand...
Click to collapse
This is an action of last resort. Exhaust all other avenues first.
boscorama said:
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
Click to expand...
Click to collapse
I used CWM to flash AOSP 4.1.2. It seemed to work fine for a day or two, but then it needed charging (as normal). I let it charge over night and in the morning it had less battery. I figured the charger or cable were flaky so I tried another set on another outlet and same thing. Then it finally ran out of battery. I let it charge again over night and when I tried to turn it on it was really slow. The boot animation was only 1 frame every couple seconds. It would eventually boot all the way up, but it was still REALLY slow. So I went into CWM and reflashed the same ROM. Then I got a boot loop of the boot animation. I couldn't get into CWM any more, so then I went into download mode and flashed the official firmware and flashed it with ODIN.
boscorama said:
How far into the boot sequence does it get?
Click to expand...
Click to collapse
Now when I turn it on it just says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I can flash again with ODIN and it will get to the Samsung boot animation and just pulse SAMSUNG.
boscorama said:
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Click to expand...
Click to collapse
If I hold power and volume down I can get into download mode or Samsung recovery, not CWM, and power with volume up doesn't do anything.
boscorama said:
Have you tried seeing what is causing the boot-loop using adb?
Click to expand...
Click to collapse
I don't know anything about adb and I'm not sure what I would be looking for. Is there a tutorial I can follow somewhere?
Thanks for any help!
This worked for me with similar problem
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Thanks! I'll give this a try when I get home. I'll let you know how it works out.
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
jd1639 said:
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Agreed - my procedure avoids manual repartitioning - I tried lots of other procedures but none worked. I think my data partition had become corrupt because I kept getting error messages. My first try was to recover with my cwm recovery file I made originally but I kept getting back to the boot loop .
spazlon said:
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
Click to expand...
Click to collapse
I always got something like that ...
After bootloop just go to recrovery mode then factory riset ... its 100% WORK
Sent from my GT-P7300 using xda premium
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
Sorry - being a newbie myself I'm at a loss. It worked a charm for me.
spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
did a format /system before installing the custom roms? This is an important step.
prince93 said:
did a format /system before installing the custom roms? This is an important step.
Click to expand...
Click to collapse
This fixed it. Never had to do it with any of my other devices. CM10 loaded quickly after that. Loving how fast JB is!
Thanks!
Sent from my GT-P7310 using Tapatalk HD
It worked
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
WOw! This fixed my Tablet! thank you ever so much!!
mjramos15 said:
WOw! This fixed my Tablet! thank you ever so much!!
Click to expand...
Click to collapse
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
Gee thanks. This saved my tab. I'd almost given up on it and then voila.
See several posts below for the steps that worked for me
I'm posting this here because my post in the Q&A forums has received zero replies.
I feel like I've tried everything. I installed the UVMA1 over-the-air update and have lost and am unable to regain root. I seriously need a solution to this.
Has anyone been able to root the most updated SGH-T879 with the UVMA1 build?
Re: [Q] Rooting the OTA updated UVMA1 build
You have to do following steps
1.download CWM recovery. tar
2.download odin flashable CWM touch recovery.tar
3.go to download mode
4.flash the UVAM1.tar file through odin
5.flash the CWM recovery.tar through odin
6.flash the CWM touch recovery.tar through odin
7.go to recovery mode flash the super user
8.reboot
You should be okay...
I hope that it helping you to Root the phone.
Let me know if you did.
Good luck..
Sent from my SGH-T879 using xda premium
Flash the CWM recovery tar through Odin.
https://www.onlinefilefolder.com/3sYujqhSWDjt5I
After CWM has been installed, flash superusers through recovery.
https://www.onlinefilefolder.com/3sRc8Cz8TcpOLC
To change recovery to TWRP (which most people seem to prefer now days) flash TWRP zip through CWM recovery. I like this method better than trying to install TWRP through Goomanager, I always have trouble with that for some reason.
Paste below address into your browser
goo.im/devs/OpenRecovery/sgh-t879/openrecovery-twrp-2.3.1.1-sgh-879.zip
Now your phone is rooted and you have TWRP.
Re: [Q] Rooting the OTA updated UVMA1 build
I did as same as it.
But. I couldn't go to recovery
That is why important that make it sure flashing CWM touch recovery.tar through odin.
Maybe just my phone?.
Thank you.
Sent from my SGH-T879 using xda premium
I got my phone to root, but have been unable to change the recovery so I can switch to 4.2.2.
I will clean this up as time permits.
Success!
Through trial and error, on Ubuntu and Windows, I have managed to successfully root the UVMA1 build. I did not screenshot the process so I'll be going from memory. On the other hand I will post a stock backup of the ROM for everyone to use as needed.
This did not work on Ubuntu, had to use Windows.
You will need:
Android Tools SDK
CWM
most recent ODIN
Superuser zip
Steps:
download Android Tools SDK.
Extract to your C: on your windows machine
Open command prompt and navigate to the Platform-Tools directory
enable debugging mode on your Note (Settings > Developer Options > USB Debugging
Leaving your phone on, connect via USB to your computer
wait while the Samsung drivers load
On command prompt type "adb reboot-bootloader" or "adb reboot bootloader" and wait (might need to try both)
Your phone should reboot into downloader mode
Open the newest version of ODIN
In Odin, nothing significant will change, I only saw a blue box in the first square top left
Click on 'Bootloader' button and select the tar.md5 file from Tomin's Goodies thread (link to come later)
In Odin, click on Start
Odin will scroll some text in the little window (bottom left) and then stop. I waited about five minutes. Nothing changed.
Disconnect your phone, pull the battery, press the power button (to dissipate magic electrons), put the battery back in and turn the phone on
Your phone should show a screen saying there is an issue with the Firmware and to use Samsung Kies to fix it. IGNORE THIS, don't do anything
Reconnect phone to PC via USB
wait about 30 seconds for the computer
In Odin, press Start again.
Odin should do something differently than the first time, you should see the top left window go green and 'Reset Ok' in the bottom left window.
Your phone will reboot. If it loads to Android then go to the command prompt window on your PC and type 'adb reboot recovery'
wait about a minute. CWM should load on your phone.
Now is the time to install Superuser zip through CWM.
Additionally, clear dalvik and other caches, reset permissions and backup your rom to external SD card now.
If anyone tries this, please document the process with screenshots so we can create a more comprehensive tutorial.
Recently i wanted to a full wipe including internal storage on my nexus 5 and since nexus 5 does not have external storage i found it a bit tricky to flash a rom again...
so,here im going to explain the easiest and simplest way to install a rom via adb sideload on nexus 5 using TWRP after a complete wipe
I am not responsible for bricked devices.
Please do some research if you have any concerns about adb sideload
BACKUP YOUR DATA FIRST
1.Download the file and place it on desktop View attachment Nexus5.zip
2.boot your device into recovery, wipe everything and connect it to pc and make sure drivers are installed. if not do as follows:
open device manager in control panel and if drivers are already installed, it shows something like ANDROID ADB INTERFACE,
if not,it shows some name with yellow symbol..
right click on it and select update drivers and select browse my computer and select let me pick..
click next > have disk>browse> and select the usb_drivers in downloaded file> open > open > ok
now it shows as ANDROID ADB INTERFACE..
3.In TWRP, select advanced and choose sideload option.
4.open command prompt and change the directory to where you downloaded the file ( easy if on desktop )
to open command prompt: win+r>cmd
for changing directory: cd desktop > cd nexus5
5.Now type adb devices in command prompt and it should show list of devices with your device code name and mode as sideload mode.
if not install drivers again.
6.copy your ROM zip file to the folder 'Nexus5' which you downloaded.
7.type adb sideload romzipname
8.now it starts copying and wait till it shows 100%. after copying it automatically starts installing.
when the installing is finished,it shows reboot system. reboot and njoy :highfive:
Note: If stuck while flashing rom, hold power and volume down until it reboots to fastboot then go to recovery and repeat the same procedure.
Please hit the 'thanks' if this helped you.
jaj473 said:
Recently i wanted to a full wipe including internal storage on my nexus 5 and since nexus 5 does not have external storage i found it a bit tricky to flash a rom again...
so,here im going to explain the easiest and simplest way to install a rom via adb sideload on nexus 5 using TWRP after a complete wipe
I am not responsible for bricked devices.
Please do some research if you have any concerns about adb sideload
BACKUP YOUR DATA FIRST
1.Download the file and place it on desktop View attachment 2461684
2.boot your device into recovery, wipe everything and connect it to pc and make sure drivers are installed. if not do as follows:
open device manager in control panel and if drivers are already installed, it shows something like ANDROID ADB INTERFACE,
if not,it shows some name with yellow symbol..
right click on it and select update drivers and select browse my computer and select let me pick..
click next > have disk>browse> and select the usb_drivers in downloaded file> open > open > ok
now it shows as ANDROID ADB INTERFACE..
3.In TWRP, select advanced and choose sideload option.
4.open command prompt and change the directory to where you downloaded the file ( easy if on desktop )
to open command prompt: win+r>cmd
for changing directory: cd desktop > cd nexus5
5.Now type adb devices in command prompt and it should show list of devices with your device code name and mode as sideload mode.
if not install drivers again.
6.copy your ROM zip file to the folder 'Nexus5' which you downloaded.
7.type adb sideload romzipname
8.now it starts copying and wait till it shows 100%. after copying it automatically starts installing.
when the installing is finished,it shows reboot system. reboot and njoy :highfive:
Note: If stuck while flashing rom, hold power and volume down until it reboots to fastboot then go to recovery and repeat the same procedure.
Please hit the 'thanks' if this helped you.
Click to expand...
Click to collapse
in the cmd prompt it keeps telling me it cannot read my rom file. any helpm please?
b_rangel29 said:
in the cmd prompt it keeps telling me it cannot read my rom file. any helpm please?
Click to expand...
Click to collapse
Did you copy the rom file to Nexus5 folder?
Why not use WugFresh's tool.... that thing does everything.
Sent from my Nexus 5 using Tapatalk
We try to discourage the use of toolkits as they remove the "ability" element or the "learning" aspect.
Doing things manually teaches the skills to get out of trouble later on.
Sent from my Nexus 5 using Tapatalk
try to update usb driver. browse the file inside dowloaded file but it came result windows was unable to instal your nexus 5
i'm using windows 7
any sugestions?
Help
So, I have/had a N5 on stock 4.4.4 rom, rooted & Xposed installed with TWRP & a lollipop preview on MultiRom.
Was installing the new Lollipop .zip. In an act of hurried stupidity, I wiped my phone, including the internal storage.
Which for some reason also wiped my NANDROID backup. I thought that is not supposed to be wiped even when doing an internal storage wipe, BUT it did.
Now, all i have is TWRP on my phone with no rom installed.
I tried connecting my phone to the pc to see if i can just transfer the rom file onto the internal memory, but nothing shows up when i connect my phone to PC.
after some searching, I ended up in this thread.
The problem is, when i connect my phone to the PC, the phone doesn't show up in the device manager.
So i cannot install the drivers & android SDK itself.
So, How do i Install a rom onto it?
I have a PC & a MAC, so i can use either of the machines. But i don't have much technical knowledge about stuff, I did all the above modifications with the help of tutorials & guids. so ELI5 please.
Please help!
Thank you.
Jugal.PM said:
So, I have/had a N5 on stock 4.4.4 rom, rooted & Xposed installed with TWRP & a lollipop preview on MultiRom.
Was installing the new Lollipop .zip. In an act of hurried stupidity, I wiped my phone, including the internal storage.
Which for some reason also wiped my NANDROID backup. I thought that is not supposed to be wiped even when doing an internal storage wipe, BUT it did.
Now, all i have is TWRP on my phone with no rom installed.
I tried connecting my phone to the pc to see if i can just transfer the rom file onto the internal memory, but nothing shows up when i connect my phone to PC.
after some searching, I ended up in this thread.
The problem is, when i connect my phone to the PC, the phone doesn't show up in the device manager.
So i cannot install the drivers & android SDK itself.
So, How do i Install a rom onto it?
I have a PC & a MAC, so i can use either of the machines. But i don't have much technical knowledge about stuff, I did all the above modifications with the help of tutorials & guids. so ELI5 please.
Please help!
Thank you.
Click to expand...
Click to collapse
Read here - http://forum.xda-developers.com/showthread.php?p=48915118
Sent from my Android 5.0 Nexus 5
accidently wiped internal memory in lenovo p1m
i accidently wiped internal memory using twrp. so now can i flash a custom rom for my lenovo p1m
I know this one has been answered a few times in pieces, and somewhat understandable manner. However, I wanted to decrypt this for everyone to be able to understand how to do it and to overcome this particular issue.
Issue: You have a custom recovery installed and your LG G2 prompts you to install the new OTA (i.e. KitKat update). You then accidentally/unknowing of consequences accept the update. Your phone restarts and keeps going to the custom recovery which you had installed, instead of booting to the update. You endlessly try to boot to your phone, but it just keeps going back to your custom recovery.
Things to do ahead:
1. Have LG G2 drivers installed on computer you will be using. You can get those from the LG website easily by searching LG G2.
2. Obtain ADB and fastboot files from HERE
3. Obtain working TWRP vs 2.7.0 from HERE if you don't have the TWRP recovery installed (i.e. if you're using CWM or Philz recovery).
Recovery Procedure:
1. If you have TWRP recovery installed, proceed from step 9
2. If you have CWM or Philz recovery installed, follow these next steps.
3. When inside CWM/Philz recovery, click on option to install zip.
4. Have your phone connected to a computer which has the LG G2 drivers installed, found on LG's site. Make sure to install drivers without phone connected to computer first. After installing, restart computer, and then plug phone to computer USB port.
5. Now that you have the phone plugged to comp, and that the comp has recognized your phone, open up CMD and navigate to the folder where you have your ADB file located and workable TWRP recovery zip file.
6. Once there, click on install using sideload on your phone's custom recovery which should be located inside the install zip option.
7. Then type in CMD on computer this: ADB sideload TWRP-file-name.zip
Note. Replace TWRP-file-name.zip with whatever the TWRP zip file on your computer is named to the letter.
8. Your phone will install TWRP recovery at this point. Once it finishes, restart your phone by rebooting recovery (should be an option somewhere there in the main level of the recovery)
9. TWRP should boot now. Once inside TWRP, click on Advance
10. Then click on Terminal Command
11. Next click on Select
Note: Do not navigate to any other folder. Just click on Select. You'll know what I mean once your in Terminal Command.
11. Type this command in the space provided in your phone (NOT in CMD) which should be now in Terminal Command mode exactly to the last letter. I'm not kidding; don't miss a character or replace a number. You risk nuking your phone. Double check your typing.
Type this: dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/fota
Note: You should note that there is a space between dd and if=/dev, and another space between /zero and of=/dev
12. Once the command finishes running, about 30 seconds or less, restart phone. And voila. Your phone should boot back to your pre-selecting update with OTA mode.
In my case, I wiped everything and tried restoring one of my nandroids. That did not help me boot my phone. However, when I did the above mentioned steps, my phone booted to my backed up state which I installed prior.
Hopefully you don't end up being a victim of this. But if you are, now you can confidently bring yourself back :good:
Good luck and share your progress. Thanks!
Cheers,
~Atrio
Terminal Command didn't work ...
AtriosM3 said:
I know this one has been answered a few times in pieces, and somewhat understandable manner. However, I wanted to decrypt this for everyone to be able to understand how to do it and to overcome this particular issue.
Issue: You have a custom recovery installed and your LG G2 prompts you to install the new OTA (i.e. KitKat update). You then accidentally/unknowing of consequences accept the update. Your phone restarts and keeps going to the custom recovery which you had installed, instead of booting to the update. You endlessly try to boot to your phone, but it just keeps going back to your custom recovery.
Things to do ahead:
1. Have LG G2 drivers installed on computer you will be using. You can get those from the LG website easily by searching LG G2.
2. Obtain ADB and fastboot files from HERE
3. Obtain working TWRP vs 2.7.0 from HERE if you don't have the TWRP recovery installed (i.e. if you're using CWM or Philz recovery).
Recovery Procedure:
1. If you have TWRP recovery installed, proceed from step 9
2. If you have CWM or Philz recovery installed, follow these next steps.
3. When inside CWM/Philz recovery, click on option to install zip.
4. Have your phone connected to a computer which has the LG G2 drivers installed, found on LG's site. Make sure to install drivers without phone connected to computer first. After installing, restart computer, and then plug phone to computer USB port.
5. Now that you have the phone plugged to comp, and that the comp has recognized your phone, open up CMD and navigate to the folder where you have your ADB file located and workable TWRP recovery zip file.
6. Once there, click on install using sideload on your phone's custom recovery which should be located inside the install zip option.
7. Then type in CMD on computer this: ADB sideload TWRP-file-name.zip
Note. Replace TWRP-file-name.zip with whatever the TWRP zip file on your computer is named to the letter.
8. Your phone will install TWRP recovery at this point. Once it finishes, restart your phone by rebooting recovery (should be an option somewhere there in the main level of the recovery)
9. TWRP should boot now. Once inside TWRP, click on Advance
10. Then click on Terminal Command
11. Next click on Select
Note: Do not navigate to any other folder. Just click on Select. You'll know what I mean once your in Terminal Command.
11. Type this command in the space provided in your phone (NOT in CMD) which should be now in Terminal Command mode exactly to the last letter. I'm not kidding; don't miss a character or replace a number. You risk nuking your phone. Double check your typing.
Type this: dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/fota
Note: You should note that there is a space between dd and if=/dev, and another space between /zero and of=/dev
12. Once the command finishes running, about 30 seconds or less, restart phone. And voila. Your phone should boot back to your pre-selecting update with OTA mode.
In my case, I wiped everything and tried restoring one of my nandroids. That did not help me boot my phone. However, when I did the above mentioned steps, my phone booted to my backed up state which I installed prior.
Hopefully you don't end up being a victim of this. But if you are, now you can confidently bring yourself back :good:
Good luck and share your progress. Thanks!
Cheers,
~Atrio
Click to expand...
Click to collapse
I repeated this three times, and no luck... any suggestions?
I did it a tad differently. I am running Windows 7.
First I downloaded these universal drivers so my phone was recognized under Device Manager, went to my adb directory with command prompt and typed the following:
adb shell
dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/fota
I just preferred using the keyboard, but your directions will work, too.
secure booting error
got the OTA update ...after that boots to Logo with a "secure booting error" message then a black screen, can't go to download mode, phone is recognized as QHSUSB in device manager, factory recovery doesn't work.
what can be done in this case??
eddie 2t said:
got the OTA update ...after that boots to Logo with a "secure booting error" message then a black screen, can't go to download mode, phone is recognized as QHSUSB in device manager, factory recovery doesn't work.
what can be done in this case??
Click to expand...
Click to collapse
U had a custom recovery flashed correct? To me it sounds like your on stock recovery
bleedingthru said:
U had a custom recovery flashed correct? To me it sounds like your on stock recovery
Click to expand...
Click to collapse
I rooted the phone, tried to install clockwork but didn't succeed so I forgot about it, then the update totally screwed me.
eddie 2t said:
I rooted the phone, tried to install clockwork but didn't succeed so I forgot about it, then the update totally screwed me.
Click to expand...
Click to collapse
Ive never used cwm on this device only twrp so i dont know about that recovery
boot
I have philz touch and all my phone will do is boot to philz?
I received as gift a samsung watch, that come with Tizen, I will describe how to do all the steps to install the custom rom.
I have a lot of problem and I write this to help all in special noobs like me.
(no wondershare, no root, no phone needed)
Things I used:
Odin 3.12 - Will write into rom of your device, in this case gear.
Stock Rom (Go to Sammobile, you will have to do a account) - "Rom original to install".
Null rom (don't get the 27, the last version is 23)
ADB
Samsung Drivers
In some cases:
SDB
Downgrade Tizen To Android
I will write the other steps bellow it's just too much things to do it.
I will came back to say all steps. and putting links and forum I was based.
Process
Steps
[Step USB Debuging](Gear)
[Preparation 1 - ADB and verify android](Windows)
[Preparation 1.1 - In case you have tizen installed](Windows)
[Preparation 2 - Intall custom recovery](Windows)
[Preparation 3 - Copying null_23 to sdcard](Windows)
[Installing Null rom 23](Gear)
[Step USB Debuging]
Unlock you phone, and enable usb debuging
You don't need to use a phone to do it. At any version of SO installed you can go without a phone.
In case you think you need the phone to go to configuration you don't need.
Press the touchscreen on the version of your watch, at least 10 times, then press and hold where is writed gear, and you will unlock the phone.
Go to configurations, about the phone select usb debuging.
If you are not seeing the usb debuging, then go to the menu and click 7 times on version, and will unlock the usb debuging.
Go back and enable usb debuging. If you having problems I do a tutorial, but send a picture of your watch and screen.
[Preparation 1](Windows)
First thing you need to know if you are using Android or Tizen OS.
Install Samsung Drivers, to recognize your gear, connect the gear to computer.
Install ADB, or download it.
Then open a terminal, windows + R type cmd and press enter.
Navigate ADB folder, and type adb devices, if no device is show and you have gear plugged and dock and at pc with the right part of gear at the dock, and Samsung drivers, maybe you are using Tizen.
You can't go on until you see the device at adb devices.
[Preparation 1.1](Windows)
In case you wanna see if you are using Tizen then:
Install SDB, or download it.
Then open a terminal, windows + R type cmd and press enter.
Navigate SDB folder, and type sdb devices, if are showing devices you are using Tizen and need to do a Downgrade to Android to continue the installation.
Download the downgrade, unzip and do as I say, because I was doing wrong and my touch stopped working, then I need to reinstall the stock rom.
[Go to download option]Hold power button for 10 seconds, than press it at least 10 times, press until download and then press for 3 seconds and released.
Open Odin, connect you gear to pc.
You have to see [com:X] to see that your gear is connect.
Than select the pit tab, select the file .pit inside the folder you unziped.
Select the file at AP that started with 1.
Uncheck all, and leave only Reset time and Repartion checked.
WAIT until you see PASS, don't remove it at RESET.
Please now you don't go again to download option, you have to go to recovery, if you don't do it your touch will not work, and you will need to reinstall stock and restart full proccess.
[Go to recovery option] Hold power button for 10 seconds, than press it at least 10 times, press until recovery and then press for 3 seconds and released.
[Black screen]You now have to see the lack screen of death to continue, it say you have to connect to Kies and stuff(Just don't do it).
Now at this black screen you can continue.
Close Odin, and open it again.
Select at Ap rom that started with 2, uncheck auto restart, and press start.
WAIT until Odin say to Pass, don't remove at RESET.
If every thing goes right you installed MK7, and can continue the proccess.
Reboot and do the step again [Step USB Debuging].
[Preparation 2 - Intall custom recovery](Windows)
You have android installed at your gear, if you don't have the mk7 version, please download it at sammobile, use odin with checked restart and reset time, and hit start.
Now with MK7 version you will install a modification to when you use the [Go to recovery option], and now will have another feature this recovery.
At this new feature you can install a custom rom, and this case we will install null23(that is the lastest version, do not install null27)
To do so you will install a custom recovery TWRP, this will only affect the recovery option of your rom.
Open Odin, select the twrp.tar, and hit start.
Wait for PASS, and reboot and do the step again [Go to recovery option].
Check if touch is working, if this is not working, and you did a downgrade you need to do it again, i did this step at least 10 times, and the problem was I wasn't doing exatcly as I said.
If touch work you can go to the next step.
[Installing Null rom 23](Gear)
Now if your recovery changed you can go to your new customized recovery.
[Go to recovery option]
Click at wipe.
Wait, and back to menu.
Install, look for null_23.zip
Click at it.
Now you are installing the custom rom.
End
Hope I Helped.
filipemelo said:
[Installing Null rom 23](Gear)
Now if your recovery changed you can go to your new customized recovery.
[Go to recovery option]
Click at wipe.
Wait, and back to menu.
Install, look for null_23.zip
Click at it.
Now you are installing the custom rom.
End
Hope I Helped.
Click to expand...
Click to collapse
In what step did you actually install null_23 onto the gear??? In recovery I see twrp folder, but null 23 is not under it. I'm stuck at this point because I can't put null 23 in my sd card so I can install it.