Related
hey guys, i am not new to the scene but i have actually run into a big problem.
A few minutes ago i flashed a Hero rom followed by the ebi1 kernel, it booted up perfectly fine and went into installation, still no problems.
Once installation finished i learned that for some reason the home app(launcher) doesn't load, it just constantly gives an error force close when trying to go to the home.
Everything else does work.
I then decided to reflash the ROM, when booting my phone it would not go into recovery, i held the home button and it froze at rogers logo,
I tried again after a battery pull and same result, i thought uh oh, BRICK!
When i rebooted again( holding nothing down ) I learned that it apparently does boot! if i leave it alone, it does the whole buttons light up screen dims thing just before it boots, then the screen dies off and I hear a sound meaning usb connected, **(all this while it is still showing the second boot screen)**
The end button works to turn screen off and on but it it stuck at the second (MLGIN or whatever nexus style boot screen)
I nave now found a way to actually get past the boot screen, if i call the phone it will go into the dialer and I can actually use it as a phone!!, once in like this I can actually use the phone completely except for going to launcher(home), I can make calls (if someone calls me to get into the dialer), use the lockscreen, send a message (if someone sends one to me), enable usb mount.
I have a nandroid and a BART saved but like I said i cannot get into recovery.
Any help is GREATLY appreciated.
Please let me know if my post doesnt make any sense, i can try and get my thoughts out again!
EDIT I CAN get Droid explorer to work, this means i can install any apps that could help! but i dont think i could launch them
-with droid explorer i can use terminal, cant i launch stuff with that? also, when i click Bart manager it says i need to buy a license, aww
- I clicked on reboot into recovery in droid manager, the phone rebooted but it hung at the rogers logo, I really cant understand how the recovery doesn't work!
EDIT it WILL boot into fastboot mode!
Can i install an alternate launcher with droid explorer, I think that if i can do this, when i hit home it will give me the option of choosing which laucher right? i then choose the new one.
Any one know where to get a different launcher? or perhaps the launcher from this ROM so i can try and reinstall it
Because i can use droid explorer, the options are nice,
I still need help organising the above attempt, but if that fails I could also use the flash recovery image option in DE and try that.
Am i right in saying that I should first try and get a different launcher to work or should i go straight for the recovery. If the recovery doesnt wokr could I lose access to the phone booting? (thus droid explorer)
OK I would LOVE some community help here:
I think i wave 3 options
1) install any apk (namely a new launcher and get the phone to atleast function properly)
2) Re flash a recovery image
3) Flash a ROM
All of these would be done with droid explorer, i think i have listed them from least risky to most risky (if i flash ROM and that doesn't fix it i could be out of droid explorer)
Could you guys help me start up, where can i get what, my mind is racing too much!!!
ok, using droid explorer i re flashed the recovery, it now boots into recovery. i am going to reflash the hero rom as i really want to use it!
Hello
i have a problem with my nexus one,
i tried to install some theme's and it whent horribly wrong.
when ever i boot my nexus one it tells me prosesses have stopped unexpectedly, and it shuts down again. and it stays in this loop.
now ive tried to recover my phone a few times with
"fastboot devices"
"fastboot flash recovery "image file""
how ever the command promt doesnt go beyond "waiting for device"
i think the problem is that USB debugging is turned off, is there any way of turning this on without haveing to go to settings ? (couse yeh i cant get there)
please help me on this one
hope im not totaly f-ed
//Duvel
sorry if there are typo's im dutch
did you put the phone into fastboot mode, before you tried the fastboot command? and second, why are you flashing the recovery image? that won't fix you phone
i think you should try a factory reset, either by flashing your rom again or by selecting some option. what rom do you have installed? stock? if not, which and which recovery image do you have installed? there is an option in amon_ra's image do factory reset. i never used the stock recovery, but there should be an option to wipe there as well. anybody?
ps: please stop using fastboot and adb commands, if you are don't know what you are doing, before you brick your phone.
i used the following guide to root
forum.xda-developers.com/showthread.php?t=636795
i just stoped at the part where the sence ui was installed,
yes i put my phone into fastboot mode but again i think the problem is that i cant enable USB Debugging
ok i just recovered my phone with the following image
"CyanogenMOD version : recovery-RA-nexus-v1.7.0-cyan.img"
how ever im still getting unexpected application stops,
com.android.setupwizard
com.android.bluetooth
com.android.callender
com.android.mms
any idea on how to restore them ?
maybe its usefull to know i tried to use the morph "BlackMatteMorph"
from the following thread "forum.xda-developers.com/showthread.php?t=654858"
//Duvel
got it fixed now
thanks alot FloOGB some of your pointers realy helped me out,
i fixed it by installing the drivers provided by th3fallen
"forum.xda-developers.com/showthread.php?t=613217"
after that i followed the following steps got from from a post of Jeremy Sikora
"forum.androidcentral.com/google-nexus-one-roms-hacks/7366-how-install-custom-roms-your-nexus-one.html"
im sure the same topic is on XDA somewhere, this was just the first website i got directed to by google
1.) With your device powered off hold down on the volume down rocker while pressing the power button. From there select "recovery".
2.) Once in recovery select backup/restore and choose Nand backup.
When that is completed you now have a backup image saved on your SD card in case you ever need to go back to the normal ROM.
3.) Now from the recovery menu select Wipe and then Wipe data/factory reset.
4.) Once the wipe is completed select Flash zip from sdcard to select the ROM you wish to install.
5.) Once the flashing process is completed simply reboot and enjoy your freshly flashed Nexus One!
i installed the rom: Cyanogenmod For Nexus One V5.0.6
"forum.cyanogenmod.com/index.php?/topic/150-cyanogenmod-for-nexus-one-v506-04152010/?"
sorry that you arent able to click the links im providing, im new to the forum and im not allowed to make direct links yet.
so thanks again FloOGB.
//Duvel
you're welcom, no problem
even if i didn't say anything that useful i think i would have never thought about drivers since i'm using only linux and it's sort of plug and flash here.
Facts:
Ive searched the site multiple times, cannot find the same issue elsewhere
Ive unlocked my bootloader and rooted my N1, so I know how to access the bootloader/recovery
When I hold down the rollerball and hit power to start the N1, it boots straight to the OS, not the bootloader menu
The OS is: Android 2.2, Build FRF50, Kernel [email protected] #5
The OS doesnt show a cell signal
The OS has lines through moving graphics
The OS crashes to the X graphic with the moving colors about every 30sec to 2 minutes
I can access abd-mac commands via usb, but ./adb-mac reboot recovery just reboots my phone back to the OS again
I tried http://wiki.cyanogenmod.com/index.php/RE-recovery-img
but the last step of ./adb-mac shell flash_image recovery /sdcard/recovery.img
comes back with "error opening /sdcard/recovery.img: No such file or directory
Im sure the recovery.img is on the sd card
in the gui of the OS I tried looking at the available space of the sd, and it states sd- unavailable
available space - unavailable.
Any more ideas?
I can think of three options:
boot to fastboot by holding the trackball while turning on the phone (you say this doesn't work)
boot to bootloader by holding volume down while turning on the phone
if your OS is stable enough, try installing "Quick Boot" from the market (it requires root). That app has the option to reboot to either bootloader, or recovery
just follow this guide forum.xda-developers.com/showthread.php?t=636795 no such file is because you have to put the recovery image in the root folder of the sd card in other words it should'nt be within another folder when you open and view your sd card.
slicklynice said:
just follow this guide forum.xda-developers.com/showthread.php?t=636795 no such file is because you have to put the recovery image in the root folder of the sd card in other words it should'nt be within another folder when you open and view your sd card.
Click to expand...
Click to collapse
Thanks slickynice, but recovery.img is on the root of the sd card.
pikipirs said:
I can think of three options:
boot to fastboot by holding the trackball while turning on the phone (you say this doesn't work)
boot to bootloader by holding volume down while turning on the phone
if your OS is stable enough, try installing "Quick Boot" from the market (it requires root). That app has the option to reboot to either bootloader, or recovery
Click to expand...
Click to collapse
Thanks pikipirs. vol down while booting doesnt do anything for me either. I cant access anything with market. Is there a way to manually install the "quick boot" app with abd-mac?
Try something like rom manager or quickboot and see if they can get you into recovery?
MSigler said:
Try something like rom manager or quickboot and see if they can get you into recovery?
Click to expand...
Click to collapse
Do you know if any is accessible from the explorer because my market doesnt respond.
DrBlast33 said:
Do you know if any is accessible from the explorer because my market doesnt respond.
Click to expand...
Click to collapse
Hold on, I'll find the APK for the free clockworkmod rom manager.
Actually he hasn't posted an APK, why can't you get it from market again?
My OS isnt stable enough, I have no radio, so I connect via wifi. When I go to the market, it says Loading.... and then the OS crashes to the X graphic with flying colors.... and the market is closed again.
DrBlast33 said:
My OS isnt stable enough, I have no radio, so I connect via wifi. When I go to the market, it says Loading.... and then the OS crashes to the X graphic with flying colors.... and the market is closed again.
Click to expand...
Click to collapse
Does ADB work?
Yes, adb-mac command works, but ./adb-mac reboot recovery or ./adb-mac reboot bootloader doesnt boot into the recovery or bootloader, instead it just restarts the phone back to the OS.
Thats why if I can get something to install via adb, I can do it that way, and hopefully get it to the bootloader to install a working rom.
is it stable enough to try to run an app?
amazingly trivial suggestion here, but have you attempted to reset to factory defaults from inside the system? Perhaps this will give you just enough stability to accomplish a recovery load so you can get your phone back to a happy state.
Of course, I have no idea why that would resolve your issue but nobody has suggested it yet and your situation sorta sucks
Best of luck!!
Thanks for your suggestions. Yes, it freezes up when I try to do factory defaults again. But I did a factory default before I put the bad rom on it, so its pain without any apps currently. Some apps will work like the browser for a few minutes. Not many other apps to use, since it was wiped prior.
Well, looks like Im going to send it to HTC. They said it will be $196+ to fix it. They have to replace the main board which, if its the only issue, is $196. Ill be shipping it out tomorrow. Anyone with any last suggestions before I bite the bullet on $200? I guess it beats buying the phone again for $580!
Try volume down and power to boot?
MSigler said:
Try volume down and power to boot?
Click to expand...
Click to collapse
Tried it, just boots to the OS still.
Try safe mode? Turn it off, wait for the X and the unlock icon, then hold trackball until it boots. Should say "Safe mode" in the lower left corner. Might be able to get it running stable and fix from there.
MSigler said:
Try safe mode? Turn it off, wait for the X and the unlock icon, then hold trackball until it boots. Should say "Safe mode" in the lower left corner. Might be able to get it running stable and fix from there.
Click to expand...
Click to collapse
I am able to boot to safe mode.... but Im not sure what I can do while in it that I cant do while in the OS otherwise.
so i finally decided to root my lg optimus 2x, after a few tries, i finnaly did it. so after that i went to the google play store to download the app Rom Manager, after it finished installing, i went deeper into the app (Rom Manager), and found out that i could just download and install a custom rom directly from my phone, without any pc connectivity. so i choose one that was written stable on, after the custom rom was downloaded, i clicked on the icon in the notification tap to install. there were some preferences i could choose, so i decided not to backup the files from my build-in rom. after that, the phone rebooted and my phone was showing alot of text informations, and in the background of that the Rom Manager icon was showing. after the installation was done my phone got turned off. after that i decided to turn it on (obviously), and it just got stuck at the LG logo in the beginning.
so the question is, what do, i do now? i have tried everything.
AssShavin said:
so i finally decided to root my lg optimus 2x, after a few tries, i finnaly did it. so after that i went to the google play store to download the app Rom Manager, after it finished installing, i went deeper into the app (Rom Manager), and found out that i could just download and install a custom rom directly from my phone, without any pc connectivity. so i choose one that was written stable on, after the custom rom was downloaded, i clicked on the icon in the notification tap to install. there were some preferences i could choose, so i decided not to backup the files from my build-in rom. after that, the phone rebooted and my phone was showing alot of text informations, and in the background of that the Rom Manager icon was showing. after the installation was done my phone got turned off. after that i decided to turn it on (obviously), and it just got stuck at the LG logo in the beginning.
so the question is, what do, i do now? i have tried everything.
Click to expand...
Click to collapse
please move this to questions and answers
you should look into more what you need to know, need to do before flashing a custom rom
well, you either try flashing a Stock rom via Smartflash and if that doesn't work, you'll have to use Nvflash, but don't worry, your phone is fine, there's nothing to be afraid about.
Next time you try a rom, you migh want to root the device, install cwm, then make a backup with the app Titanium Backup, after that, you go into the cwm, wipe as needend and install the rom. Do read the guides there are about flashing, because things like this could happen if you don't know what your doing.
If you have done a Backup of your Rom you just simply click restore in cwm and everything would get back to normal, but since you didn't, you have to use Smartflash.
But anyways, if I were you, instead of using Smartflash as my first choice, this is what i would do:
1.- Download a CM7 rom (or any other rom i like) for the O2X in its page with the gapps (google apps), if you like Stable versions, then go for it.
2.- I'd put that rom in a microsd card directly from my pc and then put that microSD card on the device.
3.- I'd go into cwm by doing this: While the phone is off, you click: Volume down + Power button at the same time and wait until the secong LG logo appears before releasing them.
4.- I'd do the firsts 2 wipes it shows there: Data wipe/factory reset (as I already have a Titanium backup) and Cache partition wipe
5.- Go into "Advanced" and wipe: Dalvik cache and Battery stats.
6.- Go back and choose: "Install zip from SD card" then "Choose zip from sd card"
7.- Locate the file and apply it
After that you'll see that "lots of text information" you saw the first time, that's fine, just wait a little, after it's done simply click "Reboot system now" and wait a little bit for the Rom to charge for its first time, if everything goes fine, you'll have CM7 installed and your phone will be functional again.
If you like the Rom, then look for tutorials so you can configure it the way you want and flash the gapps.
Hope this helps you
I think that the reason you got stuck in LG logo, was because you were installing a rom that doesn't automatically convert the EXT3 partition into EXT4 or something, or maybe what you installed wasn't a rom, i don't know, just be sure to check a little more in the future Good luck!
Note: not all roms require to flash gapps, only Cyanogenmods and some others.
frikou said:
well, you either try flashing a Stock rom via Smartflash and if that doesn't work, you'll have to use Nvflash, but don't worry, your phone is fine, there's nothing to be afraid about.
Click to expand...
Click to collapse
Thanks for the tips, but i have problem, and this might seem like a stupid question, but how does smartflash work exactly.....?
AssShavin said:
Thanks for the tips, but i have problem, and this might seem like a stupid question, but how does smartflash work exactly.....?
Click to expand...
Click to collapse
Search a guide... it isn't difficult
Inviato dal mio LG-P990
After having issues with the low 4GB memory of the myphone uno, i decided to try rooting the phone using some online instructions using Android One Toolkit. I ended up bricking it. Now when i turn on the phone, its stuck with the 4 animated circles.
I am a noob when it comes to android phones, but i do know how to install windows xp, vista, 7. I have used online instructions to clone my pc HD using clonezilla. I believe that if someone were kind enough to give step by step instructions on what files to download(like the original "OS" / "image") and where to get them. And how to use the software, i can get my myphone uno back to working order. So please anyone out there, can you help?
t-rayms said:
After having issues with the low 4GB memory of the myphone uno, i decided to try rooting the phone using some online instructions using Android One Toolkit. I ended up bricking it. Now when i turn on the phone, its stuck with the 4 animated circles.
I am a noob when it comes to android phones, but i do know how to install windows xp, vista, 7. I have used online instructions to clone my pc HD using clonezilla. I believe that if someone were kind enough to give step by step instructions on what files to download(like the original "OS" / "image") and where to get them. And how to use the software, i can get my myphone uno back to working order. So please anyone out there, can you help?
Click to expand...
Click to collapse
If you could tell us more clearly about what did you do actually and which instructions did you followed?
DNA_Uncut said:
If you could tell us more clearly about what did you do actually and which instructions did you followed?
Click to expand...
Click to collapse
i followed(or tried to) the instructions from the site of androidmtk with topic
"how to root android one devices easily"
sorry but system will not let me paste the actual link.
Process involved the use of android one toolkit.
and now my phone no longer boots. Stuck with those 4 animated circles. I have to remove the battery to get out of that screen. But no matter what i did, isn't there a way to just install android? Like installing windows on a blank hard drive? Start from scratch? Loss of data is not a factor
t-rayms said:
i followed(or tried to) the instructions from the site of androidmtk with topic
"how to root android one devices easily"
sorry but system will not let me paste the actual link.
Process involved the use of android one toolkit.
and now my phone no longer boots. Stuck with those 4 animated circles. I have to remove the battery to get out of that screen. But no matter what i did, isn't there a way to just install android? Like installing windows on a blank hard drive? Start from scratch? Loss of data is not a factor
Click to expand...
Click to collapse
Just follow the thread
http://forum.xda-developers.com/dream-uno/development/stock-rom-spice-dream-uno-mi498-t2915844
Download ROM (from the same thread)
http://forum.xda-developers.com/showpost.php?p=61588267&postcount=23
You should get back to stock kitkat (if you follow the instructions as explained). Once you get back your phone to working. Install ota updates you receive that will get you to stock 6.01
t-rayms said:
After having issues with the low 4GB memory of the myphone uno, i decided to try rooting the phone using some online instructions using Android One Toolkit. I ended up bricking it. Now when i turn on the phone, its stuck with the 4 animated circles.
I am a noob when it comes to android phones, but i do know how to install windows xp, vista, 7. I have used online instructions to clone my pc HD using clonezilla. I believe that if someone were kind enough to give step by step instructions on what files to download(like the original "OS" / "image") and where to get them. And how to use the software, i can get my myphone uno back to working order. So please anyone out there, can you help?
Click to expand...
Click to collapse
You don't need to go back on kitkat as DNA uncut says .....your device is running on which recovery ??
devil anand said:
You don't need to go back on kitkat as DNA uncut says .....your device is running on which recovery ??
Click to expand...
Click to collapse
im sorry but i dont know what "recovery" is. The phone is also no longer turning on so i cant get that info. But im ok with trying kitkat and if the flashing of the ROM works, at least ill have a working phone. And go from there and experiment some more to get the most out of the device.
When your phone is switched off. ....press the power and volume+ button at the same time and hold it till you see a menu .....then navigate to recovery as the menu instructs ....then tell me what you see
---------- Post added at 03:58 AM ---------- Previous post was at 03:49 AM ----------
t-rayms said:
im sorry but i dont know what "recovery" is. The phone is also no longer turning on so i cant get that info. But im ok with trying kitkat and if the flashing of the ROM works, at least ill have a working phone. And go from there and experiment some more to get the most out of the device.
Click to expand...
Click to collapse
When your phone is switched off. ....press the power and volume+ button at the same time and hold it till you see a menu .....then navigate to recovery as the menu instructs ....then tell me what you see
DNA_Uncut said:
Just follow the thread
http://forum.xda-developers.com/dream-uno/development/stock-rom-spice-dream-uno-mi498-t2915844
Download ROM (from the same thread)
http://forum.xda-developers.com/showpost.php?p=61588267&postcount=23
You should get back to stock kitkat (if you follow the instructions as explained). Once you get back your phone to working. Install ota updates you receive that will get you to stock 6.01
Click to expand...
Click to collapse
i installed the Android CDC Driver. DL the SP Flash Tool and the custom ROM. Rebooted the PC. Ran the SP Flash Tool. The final stage where i click on DL and connect my phone, nothing happens. The scrolling progress bar at the bottom of the flash tool doesnt start. With or w/o batteries in the phone. What do i do next?
devil anand said:
When your phone is switched off. ....press the power and volume+ button at the same time and hold it till you see a menu .....then navigate to recovery as the menu instructs ....then tell me what you see
---------- Post added at 03:58 AM ---------- Previous post was at 03:49 AM ----------
When your phone is switched off. ....press the power and volume+ button at the same time and hold it till you see a menu .....then navigate to recovery as the menu instructs ....then tell me what you see
Click to expand...
Click to collapse
when i selected the recovery option, the next screen is a picture of the android robot lying face up. With its body panel door open with red triangle with black exclamation markm, "No command" prompt
t-rayms said:
when i selected the recovery option, the next screen is a picture of the android robot lying face up. With its body panel door open with red triangle with black exclamation markm, "No command" prompt
Click to expand...
Click to collapse
First download a custom kernel zip (recommend thunderzap 5.1)
Then SuperSU 2.54 zip
Move this to files to your phones sd card
And again go to the menu which I told you during recovery (power and volume+ buttons at same time holding) then navigate to fastboot and enter ....you will se fastboot mode in the last line of the menu .
Now connect your phone to pc and open toolkit and press root.
You will see philz recovery loaded on your phone (philz recovery written on the top).
Then tap on wipe option and then factory reset and confirm it.
After factory resetting tap on install zip and select thunderzap zip
After successful installation of thunderzap select SuperSU zip and after installation of super su ...reboot now .......it will take 10 -15 mins......
Link - kernel- http://www.thunderzap.in/downloads/
SuperSU - https://download.chainfire.eu/741/SuperSU?_e_pi_=7,PAGE_ID10,5223979215
devil anand said:
First download a custom kernel zip (recommend thunderzap 5.1)
Then SuperSU 2.54 zip
Move this to files to your phones sd card
And again go to the menu which I told you during recovery (power and volume+ buttons at same time holding) then navigate to fastboot and enter ....you will se fastboot mode in the last line of the menu .
Now connect your phone to pc and open toolkit and press root.
You will see philz recovery loaded on your phone (philz recovery written on the top).
Then tap on wipe option and then factory reset and confirm it.
After factory resetting tap on install zip and select thunderzap zip
After successful installation of thunderzap select SuperSU zip and after installation of super su ...reboot now .......it will take 10 -15 mins......
Link - kernel- http://www.thunderzap.in/downloads/
SuperSU - https://download.chainfire.eu/741/SuperSU?_e_pi_=7,PAGE_ID10,5223979215
Click to expand...
Click to collapse
great. thanks. it worked. still cant believe it. But thank you very very very much.
t-rayms said:
great. thanks. it worked. still cant believe it. But thank you very very very much.
Click to expand...
Click to collapse
Just hit thanks!!
I went to Android mtk website ...then I knew where was the problem.
Note : SuperSU zip is used to root a phone via custom recovery (twrp,philzz) ...but in marshmallow you can't root your phone just by installing SuperSU zip ....you need to install a custom *kernel* first ....remember next time??
devil anand said:
Just hit thanks!!
I went to Android mtk website ...then I knew where was the problem.
Note : SuperSU zip is used to root a phone via custom recovery (twrp,philzz) ...but in marshmallow you can't root your phone just by installing SuperSU zip ....you need to install a custom *kernel* first ....remember next time
Click to expand...
Click to collapse
i take it that this step Then tap on wipe option and then factory reset and confirm it. fixed the bricking of the phone
and these steps After factory resetting tap on install zip and select thunderzap zip
After successful installation of thunderzap select SuperSU zip and after installation of super su ...reboot now .......it will take 10 -15 mins......
rooted the phone right?
One other thing is, whenever theres a system update, during the rebooting it does an error and i have to remove battery to restart the phone. Does rooting the phone cause updates not to work?
t-rayms said:
i take it that this step Then tap on wipe option and then factory reset and confirm it. fixed the bricking of the phone
and these steps After factory resetting tap on install zip and select thunderzap zip
After successful installation of thunderzap select SuperSU zip and after installation of super su ...reboot now .......it will take 10 -15 mins......
rooted the phone right?
One other thing is, whenever theres a system update, during the rebooting it does an error and i have to remove battery to restart the phone. Does rooting the phone cause updates not to work?
Click to expand...
Click to collapse
You took a bit ....if you have rebooted your phone after just factory reset .....you may have got bootloop again.....(stuck on boot animation).
About your second problem ....
When the error happens in between these steps of installation .......you tap on reboot and install and your phone goes to recovery and after successful installation your reboots .
What's the error ??
Yeah rooting your phone changes system which causes problem while installation of the original update...??
devil anand said:
You took a bit ....if you have rebooted your phone after just factory reset .....you may have got bootloop again.....(stuck on boot animation).
About your second problem ....
When the error happens in between these steps of installation .......you tap on reboot and install and your phone goes to recovery and after successful installation your reboots .
What's the error ??
Yeah rooting your phone changes system which causes problem while installation of the original update...
Click to expand...
Click to collapse
i get the prompt about an update ready for install, i click on it, it does the prompt to reboot so i choose to reboot. During the rebooting it tries to install updates, then the robot image comes up with the word "error". Stuck there until battery is removed. Afterwards the phone will turn back on.
t-rayms said:
i get the prompt about an update ready for install, i click on it, it does the prompt to reboot so i choose to reboot. During the rebooting it tries to install updates, then the robot image comes up with the word "error". Stuck there until battery is removed. Afterwards the phone will turn back on.
Click to expand...
Click to collapse
Just unroot your phone and try updating again !!!??
devil anand said:
First download a custom kernel zip (recommend thunderzap 5.1)
Then SuperSU 2.54 zip
Move this to files to your phones sd card
And again go to the menu which I told you during recovery (power and volume+ buttons at same time holding) then navigate to fastboot and enter ....you will se fastboot mode in the last line of the menu .
Now connect your phone to pc and open toolkit and press root.
You will see philz recovery loaded on your phone (philz recovery written on the top).
Then tap on wipe option and then factory reset and confirm it.
After factory resetting tap on install zip and select thunderzap zip
After successful installation of thunderzap select SuperSU zip and after installation of super su ...reboot now .......it will take 10 -15 mins......
Click to expand...
Click to collapse
It worked for me too, but now I can`t update SuperSU.
Update from OS failed, from TWRP gives bootloop.
I`m on CM13 SNAPSHOT.
... also front camera cant take picture, but preview works ok.
Johnny_16 said:
It worked for me too, but now I can`t update SuperSU.
Update from OS failed, from TWRP gives bootloop.
I`m on CM13 SNAPSHOT.
... also front camera cant take picture, but preview works ok.
Click to expand...
Click to collapse
What's the need of updating SuperSU ..,...
Use Google camera ....
Sent from my A1 using XDA-Developers mobile app
t-rayms said:
i get the prompt about an update ready for install, i click on it, it does the prompt to reboot so i choose to reboot. During the rebooting it tries to install updates, then the robot image comes up with the word "error". Stuck there until battery is removed. Afterwards the phone will turn back on.
Click to expand...
Click to collapse
You've root? And which update do you wanna install on your phone!?
Just tell me what's your build number.. I'll help ya out.
HELP
My cousins Myphone Uno is not turning on when pressing the power button, but if I put in a charge the screen turns on after a few minutes showing the battery but I don't know if it is charging. after a minute the display will go out and the screen flashes a once or twice then off and screen turns on and display the battery it will be on a loop, I can still get to boot option when screen flashes starts,
it shows:
[Recovery Mode]
[Fastboot Mode]
[Normal Boot]
[Normal Boot +ftrace]
[Normal slub debug off]
but when I select any options or not to ,the phone will turn off. Can you help me find a way to make this phone work again? thank you in advance!
PS: If I connect it in my PC it wasn't detected and the the loop will go on and on.
Usb debugging mode is also turned off