Related
I need help really bad.....
Apparently I didnt brick my phone because I can get into hboot, but when I go to boot my phone the htc screen will go in and out ..in and out...etc...continuously....I tried flashing a radio..and when I booted it kept doing this...I cant even get into recovery AT ALL....it will just boot into htc over and over again...HELP ME PLEASE....I think I have to use adb but I need instructions....
A little backround info
I have the incredible S ... I was on the virtuous affinity rom and I restored back to my origional backup that I made when I purchased the phone...I needed a froyo radio because I had a gingerbread radio on there .... and I went to make a call and knew right away that I needed a radio....please help...OMGGGGGGGGGSO SO
IncredibleSlover said:
I need help really bad.....
Apparently I didnt brick my phone because I can get into hboot, but when I go to boot my phone the htc screen will go in and out ..in and out...etc...continuously....I tried flashing a radio..and when I booted it kept doing this...I cant even get into recovery AT ALL....it will just boot into htc over and over again...HELP ME PLEASE....I think I have to use adb but I need instructions....
A little backround info
I have the incredible S ... I was on the virtuous affinity rom and I restored back to my origional backup that I made when I purchased the phone...I needed a froyo radio because I had a gingerbread radio on there .... and I went to make a call and knew right away that I needed a radio....please help...OMGGGGGGGGGSO SO
Click to expand...
Click to collapse
I think you first have to flash the correct radio. Then flash the recovery and then the rom.
IncredibleSlover said:
I need help really bad.....
Apparently I didnt brick my phone because I can get into hboot, but when I go to boot my phone the htc screen will go in and out ..in and out...etc...continuously....I tried flashing a radio..and when I booted it kept doing this...I cant even get into recovery AT ALL....it will just boot into htc over and over again...HELP ME PLEASE....I think I have to use adb but I need instructions....
A little backround info
I have the incredible S ... I was on the virtuous affinity rom and I restored back to my origional backup that I made when I purchased the phone...I needed a froyo radio because I had a gingerbread radio on there .... and I went to make a call and knew right away that I needed a radio....please help...OMGGGGGGGGGSO SO
Click to expand...
Click to collapse
since Your phone is S-OFF and able to boot into hboot, then everything should be fine. Have you adb live in your pc (?) presumed you used windows base pc. Connect your phone to your pc and ensure all drivers are well installed. You are on hboot state > changed to fastboot (on Your Phone) > connect to pc via usb > check with command > fastboot devices > you will see the out put will be
Code:
HT13ATD00430 fastboot
if output something else please copy and paste to post here. Presumed you have proper output.
Put any rom in adb folder and run command > fastboot flash zip rom_name.zip
x1123 said:
since Your phone is S-OFF and able to boot into hboot, then everything should be fine. Have you adb live in your pc (?) presumed you used windows base pc. Connect your phone to your pc and ensure all drivers are well installed. You are on hboot state > changed to fastboot (on Your Phone) > connect to pc via usb > check with command > fastboot devices > you will see the out put will be
Code:
HT13ATD00430 fastboot
if output something else please copy and paste to post here. Presumed you have proper output.
Put any rom in adb folder and run command > fastboot flash zip rom_name.zip
Click to expand...
Click to collapse
Yes I have adb but it wont recognize my device..it says unknown device in the device manager...I am goig to pull my hair out soon.
incrediblealex said:
I think you first have to flash the correct radio. Then flash the recovery and then the rom.
Click to expand...
Click to collapse
Thanks I am trying to do that, but its saying my battery is too low in the bootloader screen...ahhhhhhh...this is too much
IncredibleSlover said:
Yes I have adb but it wont recognize my device..it says unknown device in the device manager...I am goig to pull my hair out soon.
Click to expand...
Click to collapse
You need to install HTC Sync to have your drivers properly installed.
Sent from my HTC Incredible S using XDA App
"I checked everywhere and I can't fine it. How to remove this horrible CWM ? Anything . I need anything! I tried to install 4EXT when CWM was still on and phone now seems to be bricked. It doesn't want to boot into the system or recovery. It just hangs on HTC white boot logo. Please help."
This should have been posted in the General section, not the Development section.
If you can boot the phone into HBOOT, then you can flash a new recovery image in FASTBOOT USB mode.
If you have more questions post in the GENERAL section after you have searched.
- Problem is, that when I try to flash anything it's loading it (I can see green uploading animation in HTC) but it isn't writing it (I can see quick red uploading animation) and nothing happens afterwards...
Could you recommend particular recovery image please ? I'm very tight on time.
hey ive had this happen to me before when i first started. the way i solved my problem was boot into fastboot and run the ruu it will restore everything to stock then run revolutionary to get s-off and flash cwm. then download 4ext recovery and in the app u can flash it straight over the top of cwm
heres the link to find your ruu
http://forum.xda-developers.com/showthread.php?t=1033922
try reverting to Stock.)
hey wanna try this thing..: http://forum.xda-developers.com/showpost.php?p=18079795&postcount=1 may be it'll work.)
funCrash93 said:
hey wanna try this thing..: http://forum.xda-developers.com/showpost.php?p=18079795&postcount=1 may be it'll work.)
Click to expand...
Click to collapse
This will not work. This is how the OP just into the situation he is in. The RUU will not successfully install because he has the Revolutionary S-OFF HBOOT on his phone and the RUU is not able to overwrite with the HBOOT from the RUU.
tpbklake said:
This will not work. This is how the OP just into the situation he is in. The RUU will not successfully install because he has the Revolutionary S-OFF HBOOT on his phone and the RUU is not able to overwrite with the HBOOT from the RUU.
Click to expand...
Click to collapse
I tried your RUU yesterday late night but it won't work. Only way I know to do it is to rename it to PG32IMG.zip and have it autoloaded by unlit. But it let's loaded (green loading animation) and than red loading animation which finishes but dissent make any changes I will try to find stock Rom (stock recovery?) With exe and try to flash it from console via windows. I would be happy if you could advise which file to flash as I travel and can access only wiz gprs on other phone which cost me dear and I can't really see anything I wouldn't mind to also format everything including memory where cwm or 4ext sits if its possible. I'm sorry to ask for that but will appreciate links if someone done it before due to those restrictions of searching through roaming oon company phone. Thanks guys.
birkopf said:
I tried your RUU yesterday late night but it won't work. Only way I know to do it is to rename it to PG32IMG.zip and have it autoloaded by unlit. But it let's loaded (green loading animation) and than red loading animation which finishes but dissent make any changes I will try to find stock Rom (stock recovery?) With exe and try to flash it from console via windows. I would be happy if you could advise which file to flash as I travel and can access only wiz gprs on other phone which cost me dear and I can't really see anything I wouldn't mind to also format everything including memory where cwm or 4ext sits if its possible. I'm sorry to ask for that but will appreciate links if someone done it before due to those restrictions of searching through roaming oon company phone. Thanks guys.
Click to expand...
Click to collapse
I have Vivo Pvt Ship S-On (not off) HBOOT 2.00.0000
I am trying everything and nothing wants to work. When I connect this incredible s by USB and i go to fastboot it changes to fastboot usb. so it sees the phone. but windows system doesnt see it. when i run from console "adb" and "adb devices" it says nothing is nonnected. when I got RUU with .exe extension it tells me there is connection error 260 and I can't go beyond.
Does anyone have any ideas please ?
I was really hoping that flashing from windows will solve it
birkopf said:
I have Vivo Pvt Ship S-On (not off) HBOOT 2.00.0000
I am trying everything and nothing wants to work. When I connect this incredible s by USB and i go to fastboot it changes to fastboot usb. so it sees the phone. but windows system doesnt see it. when i run from console "adb" and "adb devices" it says nothing is nonnected. when I got RUU with .exe extension it tells me there is connection error 260 and I can't go beyond.
Does anyone have any ideas please ?
I was really hoping that flashing from windows will solve it
Click to expand...
Click to collapse
Have you installed the HTC drivers on your PC? If you have installed HTC Sync to get the HTC drivers installed, make sure that HTC Sync is not running in the background or System Tray.
Penguins method actually works, though he hasnt given in much detail. I know whats he saying exactly.
One mate had the same issue, he got over it, guess there was a thread where i helped him for this issue. Have it bookmarked
here's the link : http://forum.xda-developers.com/showthread.php?t=1263465
Sorry bro, got exams till 22nd.
Cant help you to the fullest till then. But try the link and see if it helps in any way, its old thread :/
oh yes, that user Rizzu(something) in the link has his exams over, ask him or send him a pm, definitely he'll help you out
He's jobless now during his summer
birkopf said:
I have Vivo Pvt Ship S-On (not off) HBOOT 2.00.0000
I am trying everything and nothing wants to work. When I connect this incredible s by USB and i go to fastboot it changes to fastboot usb. so it sees the phone. but windows system doesnt see it. when i run from console "adb" and "adb devices" it says nothing is nonnected. when I got RUU with .exe extension it tells me there is connection error 260 and I can't go beyond.
Does anyone have any ideas please ?
I was really hoping that flashing from windows will solve it
Click to expand...
Click to collapse
Also when you are in FASTBOOT USB mode, the command to use is:
fastboot devices, not adb devices
Do you have usb debugging enabled?
Settings > Developers Options
acme anvil said:
Do you have usb debugging enabled?
Settings > Developers Options
Click to expand...
Click to collapse
I had it enabled as well as fastboot disabled but now i don't even have a system. all i can do is to power into hboot. i cant get into recovery (that's where cwm and 4ext was sitting and it hangs everytime i try to access) nothing else. i had separate drivers for htc but i have installed and updated htc sync. will kill it everytime tries to run. i still cant get over this connection problem. RUU advised above have broken or payable links. the one i tried to install is from here: http://shipped-roms.com/download.ph...igned_Raphael_52.58.25.30_1.11.25.01_Ship.exe
could someone be so kind and actually send me a link to the file that i need to insstall to finally got it moving?
i am at the moment so confused by searching thought topics i completely lost my point. please - be so kind and direct me to some downloadable link and to whatever i need to flash...
on another note - can I wipe everything somehow and than install from scratch ? (by everything i mean also the place where CWM is istting)
birkopf said:
I had it enabled as well as fastboot disabled but now i don't even have a system. all i can do is to power into hboot. i cant get into recovery (that's where cwm and 4ext was sitting and it hangs everytime i try to access) nothing else. i had separate drivers for htc but i have installed and updated htc sync. will kill it everytime tries to run. i still cant get over this connection problem. RUU advised above have broken or payable links. the one i tried to install is from here: http://shipped-roms.com/download.ph...igned_Raphael_52.58.25.30_1.11.25.01_Ship.exe
could someone be so kind and actually send me a link to the file that i need to insstall to finally got it moving?
i am at the moment so confused by searching thought topics i completely lost my point. please - be so kind and direct me to some downloadable link and to whatever i need to flash...
on another note - can I wipe everything somehow and than install from scratch ? (by everything i mean also the place where CWM is istting)
Click to expand...
Click to collapse
If that is the RUU you tried to install, no wonder you are having issues. That RUU is not for the IncS, so it is a wonder you can still even get into HBOOT.
Try this one:
http://www.filefactory.com/file/c0a...5AU_3805.06.03.03_M_release_199308_signed.exe
The problem seems to be coming from inability to connect/recognise my device in first place. I will try this suggested Rom today and let you know in few hours.
Logically thinking - what could go wrong with this phone ? I had CWM which I wanted to remove. I couldn't so I tried to install 4ext to overwrite it when I lost hope. this didn't work. Than I tried some "stock Rom" which came out to be dodgy and I'm in situation now. It's S-ON phone and all I can do is to get to hboot. But I am still cautious about this connercition error 260. I hope its because of wrong file I tried to use previously... But.... I will troy files suggested here. If that won't work - what will be next step ? Could I let's say try to download gingerbread and install it from .exe ? Would that fix it ?
tpbklake said:
http://www.filefactory.com/file/c0a...5AU_3805.06.03.03_M_release_199308_signed.exe
Click to expand...
Click to collapse
I cant access this (or the other file) that you sent me
struggling a bit to find correct on in google. What i should search for ?
birkopf said:
I cant access this (or the other file) that you sent me
struggling a bit to find correct on in google. What i should search for ?
Click to expand...
Click to collapse
I sent you a Private Message last night with a good link. Please check you Private Messages.
ok then try this.)
http://forum.xda-developers.com/showthread.php?t=1705913
tpbklake said:
I sent you a Private Message last night with a good link. Please check you Private Messages.
Click to expand...
Click to collapse
I did, but the file is corrupted (= zip archive doesn't want to open )
birkopf said:
I did, but the file is corrupted (= zip archive doesn't want to open )
Click to expand...
Click to collapse
How did you try to open it?
Copy it to your SD card and rename it PG32IMG.zip and the reboot into HBOOT and it should ask you to Update.
tpbklake said:
How did you try to open it?
Copy it to your SD card and rename it PG32IMG.zip and the reboot into HBOOT and it should ask you to Update.
Click to expand...
Click to collapse
I tried to open zip to see what's inside. It didn't want to open zip file. I tried few times before to rename it to P32IMG and upload like that. My hboot detects it, loads it but nothing happens afterwards. I will try like that if the file is not corrupted. Did anyone checked it personally ? (this particular file)
Hi, im new here. Recently Installed Rom and bunch of other things on my HTC ONE. OverClocked it as well. Longs story short. I wanted to wipe the phone but click the Format option.
Now all I have is white screen with Htc logo on it. Cant connect to the computer. Cant boot it into recovery/fastboot Menu. Will not turn off. Just stuck on that HTC logo screen. Im waiting till battery dies may be than ill atleast be able to go to fastboot...
Is it possible to bring it back or the phone is done?
My apologies if im in the wrong area/section
Phone is on Rogers/Canada.
You don't have to worry. Drain battery and boot into bootloader tomorrow. You cam always fastboot flash the Rom if it won't boot. Easiest way is via m7 tools.
Sent from my HTC One using Tapatalk 2
put the phone under a bright light and hold power+volume down
JDR0iD said:
You don't have to worry. Drain battery and boot into bootloader tomorrow. You cam always fastboot flash the Rom if it won't boot. Easiest way is via m7 tools.
Sent from my HTC One using Tapatalk 2
Click to expand...
Click to collapse
I got it to go to fastboot./ recovery now need to find out what to do next.
Own31 said:
I got it to go to fastboot./ recovery now need to find out what to do next.
Click to expand...
Click to collapse
adb sideload from computer while phone is in recovery with sideload selected
skinsfanbdh said:
adb sideload from computer while phone is in recovery with sideload selected
Click to expand...
Click to collapse
googling it now. I got it to sideload in recovery but have no idea what to do on the computor. think i need a toolkit
This works in CWM anyway
Boot into recovery
from the pc do the adb push filename.zip /data/media
wait for it to copy
then on the phone reboot recovery your rom should be in the root of the sdcard waiting for you to flash
I just tested it and it worked perfect ( of coarse I didn't format my sdcard so ymmv )
Own31 said:
googling it now. I got it to sideload in recovery but have no idea what to do on the computor. think i need a toolkit
Click to expand...
Click to collapse
The sideload works but if you mess up in AROMA or it freezes you have to start from scratch
clsA said:
This works in CWM anyway
Boot into recovery
from the pc do the adb push filename.zip /data/media
wait for it to copy
then on the phone reboot recovery your rom should be in the root of the sdcard waiting for you to flash
I just tested it and it worked perfect ( of coarse I didn't format my sdcard so ymmv )
The sideload works but if you mess up in AROMA or it freezes you have to start from scratch
Click to expand...
Click to collapse
what i dont get is what file do i flash/adb.
I downloaded SDK kits, and half a million other zips. but no idea which file to take. I understood tho, that i need to move the file from pc to the phone with adb
If you download all in one toolkit it will make sideloading easier
Sent from my HTC One using xda premium
Im just lost everywhere. dont understand anything.
using cwm or all in one tool kit or a adb direct. too many things and dont know anything about either of those steps.
do i need to do anything prior using any of the three i listed. folders, files to put into the folders.... etc.
I tried using all in 1 kit. it goes into cmd but doesnt really do anything. I also dont understand when to or what to do in the phone while im doing stuff on the computer. Which menu the phone should be in. Im looking at so many different things and non work or non i understand.
errr this is painful.
Own31 said:
Im just lost everywhere. dont understand anything.
using cwm or all in one tool kit or a adb direct. too many things and dont know anything about either of those steps.
do i need to do anything prior using any of the three i listed. folders, files to put into the folders.... etc.
I tried using all in 1 kit. it goes into cmd but doesnt really do anything. I also dont understand when to or what to do in the phone while im doing stuff on the computer. Which menu the phone should be in. Im looking at so many different things and non work or non i understand.
errr this is painful.
Click to expand...
Click to collapse
Hi mate, I'd be happy to help on TeamViewer, as I understand it is complicated to do if you're new to the commands
when using all in one toolkit it will open two cmd windows you manually close the first one after that if it says waiting for device make sure it says fastboot usb at the top of bootloader screen on your phone if it says hboot press power button once. but if your sideloading a rom your phone must be in recovery and sideload selected in recovery. once sideload is done you will have the rom you sideloaded on your sd then you will have to flash that rom.zip
is there an step by step guide or a video?
Own31 said:
is there an step by step guide or a video?
Click to expand...
Click to collapse
1. Put phone into recovery
2. Plug into PC
3. Open adb/fastboot folder on PC and drag your chosen rom into there
4. Hold down shift and right-click inside the folder and select 'Open Command Prompt Here'
5. Type 'adb push NAMEOFROM.zip /data/media/' (/data/media/0/ if you were on 4.2.2)
6. Wait for it to complete, as there will be no progress indicator. It takes around 250 seconds (4 minutes)
7. Type 'adb reboot recovery'
8. Install zip from sdcard as usual. Zip file will be on the root
thx Mac.
Lol skinfan using your info i somehow got into CWM using all in one. I closed one window. then went into recovery mod and it put me into CWM.
now i have few option, im sure you all know them.
reboot sys now
install zip from sideload
etc
Own31 said:
thx Mac.
Lol skinfan using your info i somehow got into CWM using all in one. I closed one window. then went into recovery mod and it put me into CWM.
now i have few option, im sure you all know them.
reboot sys now
install zip from sideload
etc
Click to expand...
Click to collapse
install zip from sideload
skinsfanbdh said:
install zip from sideload
Click to expand...
Click to collapse
Hmm you seem to have forgotten that there is a high possibilty of AROMA freezing and then having to restart the sideload. Why waste his time?
Mac Ill try you steps shorty. if this doesnt work whats going in right now.
skinsfanbdh said:
install zip from sideload
Click to expand...
Click to collapse
yeh dont know what i did but im pushing i think Android_Revolution_HD-One_10.1
thats the problem i dont even know what to push.
Now New update. I gues Android Rev 10.1 worked because now im in the Welcome Menu and I can install it. It asks me to. Should I? is this the right file to install?
I was gonna push cm-10.1-20130312-NIGHTLY-ville and gapps-jb-20130301-signed next. Just cause I read somewhere I had to. and try both ways. but since And. Rev 10.1 asks me to install i think i will
MacHackz said:
Hmm you seem to have forgotten that there is a high possibilty of AROMA freezing and then having to restart the sideload. Why waste his time?
Click to expand...
Click to collapse
if he downloaded rayglobe like i recommended that wont be a problem as reyglobe doesnt use aroma
---------- Post added at 10:25 AM ---------- Previous post was at 10:23 AM ----------
Own31 said:
Mac Ill try you steps shorty. if this doesnt work whats going in right now.
yeh dont know what i did but im pushing i think Android_Revolution_HD-One_10.1
thats the problem i dont even know what to push.
Now New update. I gues Android Rev 10.1 worked because now im in the Welcome Menu and I can install it. It asks me to. Should I? is this the right file to install?
I was gonna push cm-10.1-20130312-NIGHTLY-ville and gapps-jb-20130301-signed next. Just cause I read somewhere I had to. and try both ways. but since And. Rev 10.1 asks me to install i think i will
Click to expand...
Click to collapse
i would use rayglobe to at least get a fully functional rom on your phone and make a backup then flash what you want
---------- Post added at 10:33 AM ---------- Previous post was at 10:25 AM ----------
whats with the ville at the end of the cm file. i think that is not for your phone it should say m7 at the end for the htc one
skinsfanbdh said:
if he downloaded rayglobe like i recommended that wont be a problem as reyglobe doesnt use aroma
---------- Post added at 10:25 AM ---------- Previous post was at 10:23 AM ----------
i would use rayglobe to at least get a fully functional rom on your phone and make a backup then flash what you want
Click to expand...
Click to collapse
is this it? http://forum.xda-developers.com/showthread.php?t=2312312
I installed Rev and it worked (i think) asks me to setup the phone now. Not sure if it will work fully well tho.
So i was trying to get my at&t htc one back to 100% stock so i could send it in for warranty. I got my replacement htc one, but while in the process of going back to stock something happened the phone wont load into recovery, when it boots into the os it stays at the htc screen but plays the at&t boot animation sound, and to top it off the old phone wont connect properly through usb (the new one will just fine). So i am stuck in bootloader anyone have any ideas?
crazyvash1 said:
So i was trying to get my at&t htc one back to 100% stock so i could send it in for warranty. I got my replacement htc one, but while in the process of going back to stock something happened the phone wont load into recovery, when it boots into the os it stays at the htc screen but plays the at&t boot animation sound, and to top it off the old phone wont connect properly through usb (the new one will just fine). So i am stuck in bootloader anyone have any ideas?
Click to expand...
Click to collapse
what guide are you using to get to stock ?
how far did you get ? are you s-off ?
what was the last version OS on the phone ? What hboot ?
clsA said:
what guide are you using to get to stock ?
how far did you get ? are you s-off ?
what was the last version OS on the phone ? What hboot ?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2358738 this was the guide *Remove red warning from boot screen + custom hboot: http://forum.xda-developers.com/showthread.php?t=2316726 thats where things got messed up i pushed the FUU and flashed it thats where things got messed up. the phone is s-off Hboot-1.55.0000 and the os-1.20.401.1(3.10.502.2)
im guessing i screwed up and rushed things i just figured i would post as a last resort and get outside input before i decided if i should send it in as is send the new one back or what lol i appreciate any help.
crazyvash1 said:
http://forum.xda-developers.com/showthread.php?t=2358738 this was the guide *Remove red warning from boot screen + custom hboot: http://forum.xda-developers.com/showthread.php?t=2316726 thats where things got messed up i pushed the FUU and flashed it thats where things got messed up. the phone is s-off Hboot-1.55.0000 and the os-1.20.401.1(3.10.502.2)
im guessing i screwed up and rushed things i just figured i would post as a last resort and get outside input before i decided if i should send it in as is send the new one back or what lol i appreciate any help.
Click to expand...
Click to collapse
you should check this post before going any further
http://forum.xda-developers.com/showpost.php?p=47794190&postcount=3
I don't know what you mean by I pushed the FUU and flashed it. do you mean you flashed firmware?
If you flashed a custom hboot with no red text you will brick the phone when you lock the bootloader.
Don't lock bootloader !!
Use this tool to remove Tampered and set to Locked
Guru_Bootloader_Reset_1.0.zip
http://www.androidfilehost.com/?fid=23501681358538585
MD5: fdb8264a8f4741bae22939cd7734f7c2
at this point just flash the AT&T RUU
http://dl3.htc.com/application/RUU_...13_10.38j.1157.04_release_334235_signed_2.exe
and see where your at.
From the Guide you linked
Before you can proceed with the 2 following threads for removing Tampered and then Locking you need to have Superuser installed. There are links to how to do this in each thread. You can also use this toolkit. Just remember to delete the SuperUser and busybox apk if installed before you return the phone.
2. - First remove the Tampered Flag. Instructions are in this thread
http://forum.xda-developers.com/showthread.php?t=2477792
3. - Second Lock the bootloader. Instructions are in this thread
http://forum.xda-developers.com/showthread.php?t=2475914
The older REVONE commands/instructions for Tampered and Locking:
Now since you had to install SuperUser to perform the previous 2 steps make sure you unroot by deleting the Superuser.apk and busybox.apk (If installed) from the /system/app folder and also the su binary from /system/xbin on your phone.
If you ran a RUU your systems firmware and software is all reset back to stock. If you restored via Stock ROM reset or Nandroid you should be running the stock software but it could be on non stock (version mismatch) firmware.
In either case your bootloader should display Locked and no Tampered just like out of the box. Now all that’s left is to S-On. To do that issue this fastboot command:
Code:
fastboot oem writesecureflag 3
Done - device should be just like it was out of the box with no indication of any modding.
*******I am not responsible for any problems you encounter. I am simply informing you of what is needed to complete a restoration to Stock. Read all steps and commands carefully and perform them in the correct order.********
Click to expand...
Click to collapse
clsA said:
you should check this post before going any further
http://forum.xda-developers.com/showpost.php?p=47794190&postcount=3
I don't know what you mean by I pushed the FUU and flashed it. do you mean you flashed firmware?
If you flashed a custom hboot with no red text you will brick the phone when you lock the bootloader.
Don't lock bootloader !!
Use this tool to remove Tampered and set to Locked
Guru_Bootloader_Reset_1.0.zip
http://www.androidfilehost.com/?fid=23501681358538585
MD5: fdb8264a8f4741bae22939cd7734f7c2
at this point just flash the AT&T RUU
http://dl3.htc.com/application/RUU_...13_10.38j.1157.04_release_334235_signed_2.exe
and see where your at.
From the Guide you linked
Click to expand...
Click to collapse
the problem im having is the phone wont connect properly through usb to either of my computers ive tried different ports and different cables
This device cannot start. (Code 10)
A device which does not exist was specified.
thats the error i get in device status but my other htc connects perfect
crazyvash1 said:
the problem im having is the phone wont connect properly through usb to either of my computers ive tried different ports and different cables
This device cannot start. (Code 10)
A device which does not exist was specified.
thats the error i get in device status but my other htc connects perfect
Click to expand...
Click to collapse
are they both windows 8 computers ?
Windows 8.1 and hboot 1.44 don't get along
you'll have to use a driver hack to get it working
Both windows 8.1 like i said the weird part is one phone works perfect through usb the old one (the one i need to work) doesn't
crazyvash1 said:
Both windows 8.1 like i said the weird part is one phone works perfect through usb the old one (the one i need to work) doesn't
Click to expand...
Click to collapse
yeah .. here's the driver hack to make it work
Download
I repeat this is a REALLY DIRTY solution that may harm your system, personal data, hardware and/or cat.
Here are the steps:
0. Have a Linux or Windows LiveCD just in case something goes wrong
1. Download and extract files from attachment
2. Navigate to the folder corresponding to your system version (x86 = 32-bit, x64 = 64 bit)
3. Right-click franken-usb.bat and click "Run as Administrator"
5. Wait for it to finish and reboot the system. If everything went fine, you will boot your system successfully
6. Install ADB/Fastboot drivers just like on Windows 8
7. Connect your phone in Fastboot mode to your USB 2.0 port and check if it works
8. Enjoy and wait for official fix
How does it work:
It's not any kind of magic - it just replaces Windows 8.1's usbhub.sys and usbport.sys with Windows 8's ones.
Old files don't check for BOS descriptor so Fastboot can work.
Script updated - it should now actually copy the files but please double check if files were copied to C:\Windows\system32\Drivers!
Hope it helps you!
Regards!
Click to expand...
Click to collapse
Taken for here >> http://forum.xda-developers.com/showthread.php?p=49131915
It Works I been using it for over a year
Ok thank you very much i will try this when i get home from work tomorrow and hopefully its works for me then i can just follow the guide you posted to get back to stock then all will be good
im still getting the same issue with the drivers i made sure to manually install the files but still no luck.
Have you tried a Linux live boot disc? If you have troubles with Windows drivers, always fall back to Linux as it will always work if the device isn't faulty.
Sent from my HTC6500LVW using XDA Free mobile app
Uzephi said:
Have you tried a Linux live boot disc? If you have troubles with Windows drivers, always fall back to Linux as it will always work if the device isn't faulty.
Sent from my HTC6500LVW using XDA Free mobile app
Click to expand...
Click to collapse
ive been trying with linux my issue now is just getting fasboot to work (as i have very little knowledge of linux) and still having no luck with windows im considering just sending the replacement they sent and then saving and buying a phone out right
crazyvash1 said:
ive been trying with linux my issue now is just getting fasboot to work (as i have very little knowledge of linux) and still having no luck with windows im considering just sending the replacement they sent and then saving and buying a phone out right
Click to expand...
Click to collapse
all you have to do is install the driver I linked reboot the pc
put the phone is fastboot USB mode and plug it into the pc.
if it's still not visible with fastboot devices
go to device manager find the failed driver / Unknown device
choose update driver / Browse for Driver / Let me Pick / uncheck show compatible hardware
Choose HTC on the left and My HTC Version 2.0.7.22 on the Right. ...Click next / click done ..
clsA said:
all you have to do is install the driver I linked reboot the pc
put the phone is fastboot USB mode and plug it into the pc.
if it's still not visible with fastboot devices
go to device manager find the failed driver / Unknown device
choose update driver / Browse for Driver / Let me Pick / uncheck show compatible hardware
Choose HTC on the left and My HTC Version 2.0.7.22 on the Right. ...Click next / click done ..
Click to expand...
Click to collapse
ok so i got it to work in fastboot now as for getting back to stock i am on hboot 1.55 and the os will not boot now i can flash the hboot 1.44 that you linked and i can use the gruu bootloader to get the tampered and set to lock (should i do this with having no working os on the phone?) and once you run the RUU.exe doesnt the phone need to be booted up and into the os? with usb debugging enabled or can i run it with it in the bootloader or fastboot? i just want to make sure im clear before i attempted to go through and do this again lol
crazyvash1 said:
ok so i got it to work in fastboot now as for getting back to stock i am on hboot 1.55 and the os will not boot now i can flash the hboot 1.44 that you linked and i can use the gruu bootloader to get the tampered and set to lock (should i do this with having no working os on the phone?) and once you run the RUU.exe doesnt the phone need to be booted up and into the os? with usb debugging enabled or can i run it with it in the bootloader or fastboot? i just want to make sure im clear before i attempted to go through and do this again lol
Click to expand...
Click to collapse
just do the steps in order
the RUU.exe step will put the OS back on the phone and your essentially done after that
From HTC ..ignore the t-mobile
Manual system update instructions:
If you are outside of T-Mobile/Wi-Fi coverage, or the update is not found, you may perform a manual system update. This process requires that you download and install HTC Sync Manager first in order to get the proper drivers. If you do not have HTC Sync Manager installed already, you may download the software from http://www.htc.com/www/software/htc-sync-manager/.
WARNING: Performing the system update manually will delete all information from the device. Ensure all information is backed up before proceeding. See the Help & How To section of this website for more information on backing up your device contents.
Performing the ROM Update:
1. Download and save the HTC One™ for T-Mobile ROM update to your PC.
2. Connect your device to your PC via the supplied USB cable.
3. If the device is not recognized by the PC, ensure you have HTC Sync Manager installed and then disconnect and reconnect the device from the USB cable.
4. Once the device is properly recognized on the PC, locate the HTC One™ for T-Mobile ROM Update that you downloaded. Double-click on the file to launch the system update wizard.
5. Follow all of the system update wizard instructions shown on your PC.
6. Once the update is complete, click Finish in the Wizard and the device will reboot.
7. Once the device reboots, the initial setup wizard will appear.
8. Once the initial setup process is complete, the device is ready for use.
Note: If the ROM update wizard fails to recognize the device, close the wizard and then follow the steps below:
· From a powered off state, hold VOLUME DOWN while powering on the device.
· Use the volume buttons to scroll to FASTBOOT and then press the POWER button to select it.
· Connect the device to the PC while in this state and attempt the ROM update again.
To exit FASTBOOT manually, use the volume keys to navigate to REBOOT and press the POWER button to select it.
Click to expand...
Click to collapse
Thank you so much for your help everything is stock and perfect its all set and ready to be sent back
crazyvash1 said:
Thank you so much for your help everything is stock and perfect its all set and ready to be sent back
Click to expand...
Click to collapse
Very good ...just hit the thanks button and change the thread title to [solved] if you get time
( I posted this elsewhere, but i guess its beter in the actual HTCONE section) , mod feel free to delete my other one, thank you.
Good afternoon, !!!
First and foremost , I want to thank you all in advance for ANY and help, time & consideration with my current issue. I will try my best to be clear, and give all relevant info here in my first post. Please bear with me, I am pretty good when it comes to following directions, but i havent been able to find a CLEAR solution to this yet, and worried about further screwing up my phone.
** I use a mac. I currently dont have access to a PC, so i am looking for a mac remedy if possible.
I have an HTCONE m7. Tmobile.
- Bootloader - Unlocked
- S- ON
- Rooted
I kept getting a OTA software update notice for 5.14xxx, i understand the install kept failing due to the bootloader being unlocked and/or root. So after being annoyed for not able to get it, i began googling ways to get the update but to no avail. So i decided to do CM11, & recovery which i installed with no problem via, Cyanogenmod Installer.
After doing so, i realized i lost my Tmobile Wifi Calling (Yes, my own fault for not further checking that scenario before doing cm11), The wifi calling is needed 10000%, due to bad service in my apartment. Prior to finding out that cm11 doesnt contain the tmobile wifi calling , I attempted another system update thru the phone, (I assume it was updating cm11).
This is where the problem began, phone rebooted to Cyanogenmod simple recovery ,
1st few times that i tried = "apply update" > choose from internal storage , i searched different folders for the "update" file, but to no avail. The phone wouldnt start up, or install anything , and will just stay on the simple recovery. I even attempted an adb sideload. But couldnt figure that out correctly either.
After a few failed attempts, I tried wiping the phone, cache, factory reset etc. now the phone still stays on simple recovery, and all folders are gone, except for an o/ folder, that contains a clockworkmod folder, which contains nothing.
So now basically,Do i have to eventually get back to STOCK on this phone, to regain tmobile wifi calling ? IF So i need the easiest, mac friendly route to go .
Again, i thank you ALLLLL in advance, & my apologies if this is in the wrong section. Please note ive done my fair share of googling , and reading up on this. But consistently run into a problem.
OnlyEYEShine said:
Good afternoon, !!!
First and foremost , I want to thank you all in advance for ANY and help, time & consideration with my current issue. I will try my best to be clear, and give all relevant info here in my first post. Please bear with me, I am pretty good when it comes to following directions, but i havent been able to find a CLEAR solution to this yet, and worried about further screwing up my phone.
** I use a mac. I currently dont have access to a PC, so i am looking for a mac remedy if possible.
I have an HTCONE m7. Tmobile.
- Bootloader - Unlocked
- S- ON
- Rooted
I kept getting a OTA software update notice for 5.14xxx, i understand the install kept failing due to the bootloader being unlocked and/or root. So after being annoyed for not able to get it, i began googling ways to get the update but to no avail. So i decided to do CM11, & recovery which i installed with no problem via, Cyanogenmod Installer.
After doing so, i realized i lost my Tmobile Wifi Calling (Yes, my own fault for not further checking that scenario before doing cm11), The wifi calling is needed 10000%, due to bad service in my apartment. Prior to finding out that cm11 doesnt contain the tmobile wifi calling , I attempted another system update thru the phone, (I assume it was updating cm11).
This is where the problem began, phone rebooted to Cyanogenmod simple recovery ,
1st few times that i tried = "apply update" > choose from internal storage , i searched different folders for the "update" file, but to no avail. The phone wouldnt start up, or install anything , and will just stay on the simple recovery. I even attempted an adb sideload. But couldnt figure that out correctly either.
After a few failed attempts, I tried wiping the phone, cache, factory reset etc. now the phone still stays on simple recovery, and all folders are gone, except for an o/ folder, that contains a clockworkmod folder, which contains nothing.
So now basically,Do i have to eventually get back to STOCK on this phone, to regain tmobile wifi calling ? IF So i need the easiest, mac friendly route to go .
Again, i thank you ALLLLL in advance, & my apologies if this is in the wrong section. Please note ive done my fair share of googling , and reading up on this. But consistently run into a problem.
Click to expand...
Click to collapse
Here is a TWRP nandroid backup. You will have to put TWRP 2.6.3.3 on your phone. You will unzip the file and the resulting folder you will put on your phone in the following directory: //sdcard/TWRP/BACKUP/<Serial #>/<Name_of_folder>. If you are not able to get TWRP on your phone and the folder on your phone then you will need to find a Windows machine. Here is what you will need to do:
** Extract the RUU and grab the rom.zip file. This is the most important file you need from the RUU and afterwards you can delete the RUU exe if you want. To get the rom.zip from your RUU exe file, you just need to run the RUU exe file once, and then when the window is ready and waiting for you to press on the "Next" button, just leave it open and go to your temp folder. I'm using Windows XP SP3 32-bit and my temp folder is located at this path: C:\Documents and Settings\Administrator\Local Settings\Temp. Now, you will see several files and folders. Sort everything in that temp folder based on "Date Modified" with the most recent folder showing up above all other folders. This is the folder you want. The folder name will be bunch of letters and numbers. Inside that folder you will find several files, but what you need is rom.zip and android-info.txt. Copy both these files and paste them somewhere safe on your hard drive. The android-info.txt contains crucial information about the compatibility of that RUU for your phone.
** Go to your bootloader. Do:
Code:
fastboot oem lock
fastboot oem rebootRUU
This will reboot your HTC One and you will see a black screen with a silver HTC logo. Now, you will need to access the rom.zip file and flash it. I have copied my rom.zip to my adb folder located at: C:/mini-sdk/rom.zip. So, type:
Code:
fastboot flash zip C:/mini-sdk/rom.zip
Don't touch anything during the flash process. It will start and after some time, you will see FAILED error. Don't worry; it's the file preparation process if you have firmware higher than that of the RUU. Just do the same command again and the flash process will complete successfully this time. Look at the Command Prompt to know when the flash is complete. At the same time if you look at your phone, you will notice a green progress bar. When the flashing is complete on the Command Prompt, you will notice that the green bar is stuck at about 95%. This is normal. It's just a bug in the progress bar - what matters is the output from the Command Prompt window.
** Then, you reboot. Do:
Code:
fastboot reboot
This will restart your phone. Let it boot up. It might take a little longer for the first boot up sequence. You will then have completely stock software (firmware & ROM). Go to your bootloader and check that you are S-ON/OFF and Bootloader lock/unlock are unchanged from before the RUU rom.zip flashing procedure. You can now also receive OTA updates.
majmoz said:
Here is a TWRP nandroid backup. You will have to put TWRP 2.6.3.3 on your phone. You will unzip the file and the resulting folder you will put on your phone in the following directory: //sdcard/TWRP/BACKUP/<Serial #>/<Name_of_folder>. If you are not able to get TWRP on your phone and the folder on your phone then you will need to find a Windows machine. Here is what you will need to do:
** Extract the RUU and grab the rom.zip file. This is the most important file you need from the RUU and afterwards you can delete the RUU exe if you want. To get the rom.zip from your RUU exe file, you just need to run the RUU exe file once, and then when the window is ready and waiting for you to press on the "Next" button, just leave it open and go to your temp folder. I'm using Windows XP SP3 32-bit and my temp folder is located at this path: C:\Documents and Settings\Administrator\Local Settings\Temp. Now, you will see several files and folders. Sort everything in that temp folder based on "Date Modified" with the most recent folder showing up above all other folders. This is the folder you want. The folder name will be bunch of letters and numbers. Inside that folder you will find several files, but what you need is rom.zip and android-info.txt. Copy both these files and paste them somewhere safe on your hard drive. The android-info.txt contains crucial information about the compatibility of that RUU for your phone.
** Go to your bootloader. Do:
Code:
fastboot oem lock
fastboot oem rebootRUU
This will reboot your HTC One and you will see a black screen with a silver HTC logo. Now, you will need to access the rom.zip file and flash it. I have copied my rom.zip to my adb folder located at: C:/mini-sdk/rom.zip. So, type:
Code:
fastboot flash zip C:/mini-sdk/rom.zip
Don't touch anything during the flash process. It will start and after some time, you will see FAILED error. Don't worry; it's the file preparation process if you have firmware higher than that of the RUU. Just do the same command again and the flash process will complete successfully this time. Look at the Command Prompt to know when the flash is complete. At the same time if you look at your phone, you will notice a green progress bar. When the flashing is complete on the Command Prompt, you will notice that the green bar is stuck at about 95%. This is normal. It's just a bug in the progress bar - what matters is the output from the Command Prompt window.
** Then, you reboot. Do:
Code:
fastboot reboot
This will restart your phone. Let it boot up. It might take a little longer for the first boot up sequence. You will then have completely stock software (firmware & ROM). Go to your bootloader and check that you are S-ON/OFF and Bootloader lock/unlock are unchanged from before the RUU rom.zip flashing procedure. You can now also receive OTA updates.
Click to expand...
Click to collapse
Thanks for the info !!!,
But right off of the top, i am confused. I am currently downloading TMRP nandroid back up, as you said in beginning. Thing is i am unaware how to get that file onto my phone. Since it is stuck on the recovery page.... (DL is going to take a while on this machine), But if this fails, ill probably end up just tossing the phone, as i dont know anyone , nor have access to a PC machine. Sadly.
update - will attempt to push this thru via Terminal / adb will keep u posted !
-Update .. @majmoz well, i got hold of a PC laptop, did an adb / fastboot installed, dl'd the RUU, but i cant find the file from it after running the RUU. I even did cmd - Echo %temp% to make sure i was in the correct temp folder etc. Searched every sub folder there , and no zip files , or android.txt files was found . and i sorted them as u said as well.
Will continue trying tho...
Updated again - Well this time as RUU was installing again, i went to the temp files faster, and found 2 files Rom_01 & Rom_02 both zip files. But was unable to find any android text file. So now im at a standstill.
OnlyEYEShine said:
update - will attempt to push this thru via Terminal / adb will keep u posted !
-Update .. @majmoz well, i got hold of a PC laptop, did an adb / fastboot installed, dl'd the RUU, but i cant find the file from it after running the RUU. I even did cmd - Echo %temp% to make sure i was in the correct temp folder etc. Searched every sub folder there , and no zip files , or android.txt files was found . and i sorted them as u said as well.
Will continue trying tho...
Click to expand...
Click to collapse
The RUU Update Window should still be on the computer when you are looking for the files. Once the RUU goes past the first screen, the folder will be erased. You should also sort the /Temp folder by date so the most recent folder is at the top.
majmoz said:
The RUU Update Window should still be on the computer when you are looking for the files. Once the RUU goes past the first screen, the folder will be erased. You should also sort the /Temp folder by date so the most recent folder is at the top.
Click to expand...
Click to collapse
If i would of refreshed the page i would of seen your response, as i just re-editted my last post. with another update. =0)
I found 2 files with rom, Rom_01 & Rom_02 , both are zip files. but i cant find any android text file .
another thing, i am trying to find adb devices , but it is not locating my phone . I was able to earlier reboot into bootloader , etc. Now it tells me repeatedly that device is not found , i have tried adb kill-server, start-server etc. .. and phone is still on cyanogen simple recovery screen . .
Thanks again for ur time & help .. .definetly is appreciated !
OnlyEYEShine said:
If i would of refreshed the page i would of seen your response, as i just re-editted my last post. with another update. =0)
I found 2 files with rom, Rom_01 & Rom_02 , both are zip files. but i cant find any android text file .
another thing, i am trying to find adb devices , but it is not locating my phone . I was able to earlier reboot into bootloader , etc. Now it tells me repeatedly that device is not found , i have tried adb kill-server, start-server etc. .. and phone is still on cyanogen simple recovery screen . .
Thanks again for ur time & help .. .definetly is appreciated !
Click to expand...
Click to collapse
Keep both ROM files and save them for future use. Since you are able to use the PC, I would just run the RUU from the PC. Then in the future try to figure out how to run the two ROM files on your Mac. Just start the RUU again and let it do its thing.
majmoz said:
Keep both ROM files and save them for future use. Since you are able to use the PC, I would just run the RUU from the PC. Then in the future try to figure out how to run the two ROM files on your Mac. Just start the RUU again and let it do its thing.
Click to expand...
Click to collapse
Hey hey , good morning. Had some errands to do last nite then fell asleep. Going to attempt this again today . Oh, and i did run the RUU on the PC so thats where ill keep them also.
Will attempt to see if i can even connect to the phone with ADB, it seemed as if i was unable to last nite.
-update I got the phone to load to bootloader, & to fastboot usb I will try now to attempt this after coffee.. =0)
HAHAHAHHAHA ,, Oh man. Ok well being that it was pretty late last nite, and i had just woken up earlier .... I didnt realize that the RUU actually does the entire process on the PC. and that i DIDNT need to use cmd., and adb etc.
I want to thank you a TON @majmoz With my day or two of aggravation , then to just not get it right last nite.. I think i wasnt there mentally to actually read and pay attention.
My phone is in set up mode now. So i am 99% sure it is all good... Again, thanks , i definetly appreciate it !
OnlyEYEShine said:
HAHAHAHHAHA ,, Oh man. Ok well being that it was pretty late last nite, and i had just woken up earlier .... I didnt realize that the RUU actually does the entire process on the PC. and that i DIDNT need to use cmd., and adb etc.
I want to thank you a TON @majmoz With my day or two of aggravation , then to just not get it right last nite.. I think i wasnt there mentally to actually read and pay attention.
My phone is in set up mode now. So i am 99% sure it is all good... Again, thanks , i definetly appreciate it !
Click to expand...
Click to collapse
Glad you are back in business! :good:
@majmoz Hey i tried sending a PM earlier . but i see it never went thru in my sent Messages.
Just wondering if you can help me one last time. As i stated, i MUST have tmobile wifi calling. I initially had my bootloader unlocked months ago, and only rooted it few days before this brick issue.
Now since i did this process to fix the phone, i see bootloader = Relocked.
I dont want to add any custom roms etc, I simple want to root the device again. I know when i just did it , it was quick n easy and simple. But as im googling for the process now, i cant seem to find any that is similar to what i just did a few days ago. The processes seem extremely long. I think i just added a superuser apk of sorts , and it rooted.
Thanks again !
OnlyEYEShine said:
@majmoz Hey i tried sending a PM earlier . but i see it never went thru in my sent Messages.
Just wondering if you can help me one last time. As i stated, i MUST have tmobile wifi calling. I initially had my bootloader unlocked months ago, and only rooted it few days before this brick issue.
Now since i did this process to fix the phone, i see bootloader = Relocked.
I dont want to add any custom roms etc, I simple want to root the device again. I know when i just did it , it was quick n easy and simple. But as im googling for the process now, i cant seem to find any that is similar to what i just did a few days ago. The processes seem extremely long. I think i just added a superuser apk of sorts , and it rooted.
Thanks again !
Click to expand...
Click to collapse
Here is a step by step guide with pictures. This is called the HTCDev method and it is pretty standard. It just looks like a lot of steps but it isn't that bad.
majmoz said:
Here is a step by step guide with pictures. This is called the HTCDev method and it is pretty standard. It just looks like a lot of steps but it isn't that bad.
Click to expand...
Click to collapse
Gotcha, will try this in an hour or so . Have some errands to run. Thanks again !
OnlyEYEShine said:
Gotcha, will try this in an hour or so . Have some errands to run. Thanks again !
Click to expand...
Click to collapse
Keep this for future reference on how to flash the two RUU ROM zip files:
From nkk71's SuperGUIDE to returning 100% back to stock - Post #1211
http://forum.xda-developers.com/showpost.php?p=55921790&postcount=1211
How to flash two RUU ROM zip files
Code:
[B]fastboot oem rebootRUU
fastboot flash zip RUU_ROM_1.zip [COLOR="Red"][I]<-- hboot preupdate[/I][/COLOR]
fastboot flash zip RUU_ROM_1.zip[COLOR="Red"][I] <-- rest of the files in "1"[/I][/COLOR]
fastboot flash zip RUU_ROM_2.zip [I][COLOR="Red"]<-- files in "2" (kernel, touchscreen drivers 2, wipe userdate)[/COLOR][/I]
fastboot reboot-bootloader
[/B]
Click to expand...
Click to collapse